Page 1 Command Manual NWA-033623-001 ISSUE 3.0 To view the latest issue of this document go to NEC Knowledgebase @ http://www.kbase.cns.nec.com.au & search for NEC-10632...
Page 2 Periodically changes are made to the information contained in this manual. Although all efforts have been made to ensure that the contents are correct, NEC shall not be liable for any direct, indirect, consequential or incidental damages resulting from the use of the equipment, manual or any related materials.
Page 3 NEC Infrontia Corporation reserves the right to change the specifica- tions, functions, or features, at any time, without notice. NEC Infrontia Corporation has prepared this document for use by its employees and customers. The information contained herein is the property of NEC Infrontia Corporation and shall not be reproduced without prior written approval from NEC Infrontia Corporation.
Page 4: Table Of Contents
TABLE OF CONTENTS INTRODUCTION PURPOSE ........................ OUTLINE OF THIS MANUAL ................... TERMS IN THIS MANUAL ..................PBX SYSTEM DESIGNATION ..................ATTENDANT CONSOLE NAME ..................TERMINAL NAME ......................COUNTRY REFERENCE ....................REFERENCE MANUAL ................... Chapter 1 HOW TO USE CAT CAT AND PCPro ...................... CAT KEY FUNCTIONS ....................
Page 5 [CM04] DISPLAY LANGUAGE FOR MULTILINE TERMINAL/DESKCON LCD, DEFAULT SETTING PATTERNS FOR MULTILINE TERMINAL, KIND OF TONE FOR IP STATION/TDM, INQUIRY NO. IN PASSWORD LOCK STATE FOR DT700 SERIES, SINGLE LINE TELEPHONE RINGING SIGNAL FOR STATION-TO-STATION CONNECTION, SINGLE LINE TELEPHONE RINGING SIGNAL FROM A TRUNK, SPECIAL RINGING SIGNAL FOR SINGLE LINE TELEPHONE RING, SETTING OF SERVICES, A-LAW/µ-LAW SETTING FOR EACH UNIT ................
Page 6 [CM35] TRUNK ROUTE DATA ................3-222 [CM36] RESTRICTION DATA/PAD DATA FOR TANDEM CONNECTION .... 3-254 [CM40] FUNCTION OF CPU RS-232C PORT ............3-256 [CM40] CPU RS-232C PORT .................. 3-257 [CM40] CPU BUILT-IN MODEM ................3-260 [CM41] SYSTEM TIMER DATA ................3-261 [CM42] SYSTEM COUNTER DATA/PAD DATA/TRUNK RESTRICTION CLASS...
Page 7 [CM77] STATION/TRUNK ROUTE/CS/ZT/DESKCON NAME ASSIGNMENT ..3-399 [CM78] DESTINATION OF SPLIT CALL FORWARDING ........3-404 [CM81] TOLL RESTRICTION PATTERN ON EACH TRUNK RESTRICTION CLASS ......................3-405 [CM85] MAXIMUM NUMBER OF SENDING DIGITS ..........3-408 [CM8A] LCR/TOLL RESTRICTION DEVELOPMENT TABLE ......... 3-410 [CM8A] TOLL RESTRICTION DEVELOPMENT TABLE .........
Page 8 [CME9] PASSWORD ....................3-532 [CMEA] FAULT INFORMATION STORE/DISPLAY FUNCTIONS ......3-533 [CMEC] MAINTENANCE BY PCPro/CAT ..............3-542 [CMEE] APPLICATION BLADE DATA ASSIGNMENT ..........3-547 [CMF0] CPU MEMORY DUMP ................3-549 [CMF1] CPU MEMORY READ/WRITE ..............3-549 [CMF5] LINE/TRUNK MEMORY/ALARM MEMORY READ ........3-550 [CMF6] ONLINE MP-FP COMMAND OUTPUT ............
Page 9 THIS PAGE LEFT BLANK INTENTIONALLY. NWA-033623-001 Rev.3.0 91toc001.fm...
Page 10 INTRODUCTION PURPOSE INTRODUCTION PURPOSE This manual explains all of the commands required for programming the SV8300, using the Customer Administration Terminal (CAT) or PCPro. NWA-033623-001 Rev.3.0 91ch0001.fm...
Page 11: Outline Of This Manual
INTRODUCTION OUTLINE OF THIS MANUAL OUTLINE OF THIS MANUAL This manual consists of three chapters. The following paragraphs summarize Chapters 1 through 3. CHAPTER 1 HOW TO USE CAT This chapter explains how to use the Customer Administration Terminal (CAT) which is used as the man-machine interface with the PBX.
Page 12: Terms In This Manual
PBX system is usually designated as “PBX” or “system”. When we must draw a clear line between the PBX systems, they are designated as follows. SV8300 : UNIVERGE SV8300 2000 IPS : NEAX 2000 IPS INTERNET PROTOCOL SERVER 2400 IPX: NEAX 2400 IPX Internet Protocol eXchange ATTENDANT CONSOLE NAME Attendant Console is usually designated as “Attendant Console”.
Page 13: Terminal Name
INTRODUCTION TERMS IN THIS MANUAL TERMINAL NAME The following digital multi-function terminals are designated as “Multiline Terminal” usually, unless we need to mention the type of terminal in particular. TERMINAL NAME PRODUCT NAME term term Multiline Digital Multiline 70 (Elite) Terminal Terminal term...
Page 14 INTRODUCTION TERMS IN THIS MANUAL COUNTRY REFERENCE The exclusive commands for specific country are described as follows; [Asia] [Latin America Only] [Australia Only] [New Zealand Only] [Australia/Argentina] [North America Only] [Australia/Europe] [North America/Latin America] [Australia/France] [North America/EU] [Australia/New Zealand] [Not used in Australia/North America] [Australia/North America] [Not used in Australia/North America/UK] [Brazil Only]...
Page 15: Reference Manual
INTRODUCTION REFERENCE MANUAL REFERENCE MANUAL Refer to the following manuals for information on each service programming. System Manual: Contains the system description and the programming procedure of the SV8300 System. Programming Manual: Contains procedure for programming each business, hotel, ISDN, OAI and WCS feature. Networking Manual: Contains the system description and the programming procedure for the CCIS, Q-SIG and Remote UNIT over IP System.
Page 16 UNIVERGE SV8300 Command Manual HOW TO USE CAT Chapter This chapter explains how to use the Customer Administration Ter- minal (CAT) which is used as the man-machine interface with the PBX. NWA-033623-001 Rev.3.0 91ch1001.fm...
Page 17: Cat And Pcpro
Chapter 1 HOW TO USE CAT CAT AND PCPro CAT AND PCPro In this system, the Customer Administration Terminal (CAT) or PCPro is used for programming the system data. The CAT is a digital multi function telephone (Multiline Terminal) which is equipped with function keys, a dial pad and LCD and interfaces with the system via the CPU blade.
Page 18: Cat Key Functions
Chapter 1 HOW TO USE CAT CAT KEY FUNCTIONS CAT KEY FUNCTIONS In the CAT mode, each key on the Multiline Terminal is automatically assigned as shown in figure below. For the function of each key, see “CAT Function Keys”. Page 1-7 CAT Key Assignment [For 8300R1]...
Page 19 Chapter 1 HOW TO USE CAT CAT KEY FUNCTIONS CAT Key Assignment term Series i Exit Help ← − − Directory Message PQRS WXYZ ← DTR-32D-1 NOTE: The buttons marked by “*” are available when using 8300R2 software or later. Continued on next page NWA-033623-001 Rev.3.0 91ch1001.fm...
Page 20 Chapter 1 HOW TO USE CAT CAT KEY FUNCTIONS • 16 Line/Trunk Feature Keys + 16 One Touch Keys (CM12 Y=24 2nd data=7) CAT Key Assignment Exit Help ← − 1 2 3 − 4 5 6 7 8 9 A 0 B ←...
Page 21 Chapter 1 HOW TO USE CAT CAT KEY FUNCTIONS • 24 Line/Trunk Feature Keys + 8 One Touch Keys (CM12 Y=24 2nd data=0) CAT Key Assignment Exit Help ← − 1 2 3 − 4 5 6 7 8 9 A 0 B ←...
Page 22 Chapter 1 HOW TO USE CAT CAT KEY FUNCTIONS CAT Function Keys FUNCTION KEY MEANING Command entry start Execution of data write Cancel of key operation (Clear entry) Display of next data (Step forward) Separator; to be entered between two different data such as first/second data (For example CM72) –...
Page 23: Cat Mode Setting Procedure
Chapter 1 HOW TO USE CAT CAT MODE SETTING PROCEDURE CAT MODE SETTING PROCEDURE To set CAT mode: term term term • For DT300/DT700 Series/D 70 (Elite)/D 75 (Series E)/D 85 (Series i) 1. Press the Keys on the terminal in the following order when the terminal is on idle state. "C"...
Page 24 Chapter 1 HOW TO USE CAT CAT MODE SETTING PROCEDURE To clear the CAT mode: term term term • For DT300/DT700 Series/D 70 (Elite)/D 75 (Series E)/D 85 (Series i) While “COMMAND= –” is displayed on the LCD. 1. Press EXIT key. 1.
Page 25: Notice On Cat Mode
Chapter 1 HOW TO USE CAT NOTICE ON CAT MODE NOTICE ON CAT MODE The CAT is used in on-line. Therefore, system data clear commands (CM00, CM01) cannot be accessed from the CAT. To use the CAT after clearing all system data, perform the following operations on the system. 1.
Page 26 Chapter 1 HOW TO USE CAT NOTICE ON CAT MODE Command List Set by Standard System Data Assignment COMMAND Y NUMBER 1ST DATA 2ND DATA REMARKS CODE 192.168.1.1 IP address of Maintenance Port of Unit No. 01 255.255.255.0 Subnet Mask of Maintenance Port of Unit No.
Page 27 Chapter 1 HOW TO USE CAT NOTICE ON CAT MODE Command List Set by Standard System Data Assignment COMMAND Y NUMBER 1ST DATA 2ND DATA REMARKS CODE 172.16.4.1 IP address of VOIP Port for control packet of Unit No. 04 255.255.0.0 Subnet Mask of VOIP Port for con- trol packet of Unit No.
Page 28 Chapter 1 HOW TO USE CAT NOTICE ON CAT MODE Command List Set by Standard System Data Assignment COMMAND Y NUMBER 1ST DATA 2ND DATA REMARKS CODE 172.16.2.5 IP address 4 of VOIP Port for voice control of Unit No. 02 172.16.2.6 IP address 5 of VOIP Port for voice control of Unit No.
Page 29 Chapter 1 HOW TO USE CAT NOTICE ON CAT MODE Command List Set by Standard System Data Assignment COMMAND Y NUMBER 1ST DATA 2ND DATA REMARKS CODE 255.255.0.0 Subnet Mask of VOIP Port for voice control of Unit No. 03 172.16.4.2 IP address 1 of VOIP Port for voice control of Unit No.
Page 30 Chapter 1 HOW TO USE CAT NOTICE ON CAT MODE NOTE 6: The standard system data is the data which shall be valid for the following data. • Station number 300 (for Digital Multiline Terminal) for Physical Port number 010101 •...
Page 31: Cat Operation
Chapter 1 HOW TO USE CAT CAT OPERATION CAT OPERATION When setting the system data, it is necessary to enter the following three kinds of data. • Command Code • First Data • Second Data The operation is explained below. To confirm the existing system data + Command Code + + First Data +...
Page 32 Chapter 1 HOW TO USE CAT CAT OPERATION The examples of data setting is described below. Example in the case that station number 300 is to be assigned to Physical Port No. 010101 and station number 301 to Physical Port No. 010102 by CM10 Y=00. Example of CAT Operation (Display) STEP 1...
Page 33 Chapter 1 HOW TO USE CAT CAT OPERATION Example of correcting the data entry In STEP 5 in the above (1) example, when has been pressed after entering “010102” by mistake, press . Then the state returns to STEP 4. STEP1: CM10 Y=00 has been entered and has been 1000>...
Page 34 Chapter 1 HOW TO USE CAT CAT OPERATION Example of deleting station number “300” assigned to Physical Port No. 010101 after completing all the operation in the above (1) example. STEP1: Press COMMAND= STEP2: Enter “1000”. (Command Code) COMMAND=10 STEP3: Press 1000>...
Page 35: Error Messages
Chapter 1 HOW TO USE CAT ERROR MESSAGES ERROR MESSAGES When an operation is incorrect, or wrong data is entered, an error message is displayed on the LCD. Error messages and their meanings are shown below. Error Messages ERROR MESSAGE MEANING OF MESSAGE ACTION CM DIGIT ERROR [0]/...
Page 36 Chapter 1 HOW TO USE CAT ERROR MESSAGES Error Messages ERROR MESSAGE MEANING OF MESSAGE ACTION SD CODE NOT Second data which is not allowed in Check whether the second data is ALLOWED/CODE the current status. available or not. NOT ALLOWED NOTE CM CODE NOT USED/ The command code entered is not in...
Page 37 Chapter 1 HOW TO USE CAT ERROR MESSAGES Error Messages ERROR MESSAGE MEANING OF MESSAGE ACTION WRONG The data stored in the memory is Clear the present data by entering wrong. This message is displayed “CCC”, or enter the correct data. when too many digits are entered.
Page 38 UNIVERGE SV8300 Command Manual PRECAUTION Chapter This chapter explains precautions for using commands, such as conditions for using commands, method of setting on-line/off-line mode, port allocation, password entry, and nation code assignment. NWA-033623-001 Rev.3.0 91ch2001.fm...
Page 39: Conditions For Using Commands
Chapter 2 PRECAUTION CONDITIONS FOR USING COMMANDS CONDITIONS FOR USING COMMANDS Some commands require a system reset after data setting, and others cannot be assigned/changed unless the system is in off-line mode (a state in which call processing is at a halt). These commands are shown in the following table, categorized according to the conditions for their use.
Page 40 Chapter 2 PRECAUTION CONDITIONS FOR USING COMMANDS Conditions for Using Commands CONDITION COMMANDS MEANINGS Commands which require a CM08>335, 368, 390, 391, Basic Services reset of the CPU blade after 392, 396, 397, 420, 592, data setting. • Press RESET switch on CM0B LAN Data Assignment the CPU blade for system...
Page 41 Chapter 2 PRECAUTION CONDITIONS FOR USING COMMANDS Conditions for Using Commands CONDITION COMMANDS MEANINGS Commands which require a CM04 Y=10-59>01, 02 Display Language for Multiline Terminal/ reset of the blade after data DESKCON LCD, Default Setting Patterns for setting. Multiline Terminal, Kind of Tone for IP Sta- •...
Page 42 Chapter 2 PRECAUTION CONDITIONS FOR USING COMMANDS Conditions for Using Commands CONDITION COMMANDS MEANINGS Commands which require a CMAE Y=00>03-05 CS/ZT Operation Data Assignment reset of the blade after data Y=10, 11, 15, 19 setting. CMEE Y=0-3 Application Blade Data Assignment •...
Page 43: Method Of Setting On-Line/Off-Line Mode
Chapter 2 PRECAUTION METHOD OF SETTING ON-LINE/OFF-LINE MODE METHOD OF SETTING ON-LINE/OFF-LINE MODE FOR CPU BLADE • Setting Off-line mode Set SENSE switch on the CPU blade to “E” or “F”. Press RESET switch on the CPU blade. • Setting On-line mode Set SENSE switch on the CPU blade to “0-4”.
Page 44 Chapter 2 PRECAUTION METHOD OF SETTING ON-LINE/OFF-LINE MODE NOTE: The data setting is as follows. • When the SENSE switch is set to E (default setting): RS-232C CONNECTION IP CONNECTION (RS1/RS2 port) (ETHERNET/VOIP port) Data speed : 9600 bps • Maintenance port Data length : 8 bits Data speed : Auto Negotiation...
Page 45: Password Entry
Chapter 2 PRECAUTION PASSWORD ENTRY PASSWORD ENTRY In a system with password service, a maintenance person is required to enter a authorization level number (Password Level) and appropriate password prior to engaging in programming the system data with the PCPro/CAT. A maximum of eight (8) Password Levels can be set up. The number of commands that the maintenance person can access is determined by the Password Level.
Page 46 Chapter 2 PRECAUTION PASSWORD ENTRY Table below shows the example for the Password Level Table. Example of Password Level Assignment MAINTENANCE PASSWORD ACCESIBLE COMMANDS PERSONNEL LEVEL Level 7 All commands Level 4 CM05, 08, 0B-13, 15, 30, 35, 36 Level 3 CM08, 0B-13, 15, 30, 35 Level 2 CM10, 11, 30, 35...
Page 47: Nation Code Assignment
Chapter 2 PRECAUTION NATION CODE ASSIGNMENT NATION CODE ASSIGNMENT With the Nation Code assigned, the system offers the particular services to the users of each country. For Australia or New Zealand, appropriate nation code to the user should be assigned by CM31 Y=0 as shown below.
Page 48: System Data Backup
Chapter 2 PRECAUTION SYSTEM DATA BACKUP SYSTEM DATA BACKUP CAUTION • If you operate as follows without system data backup after system data setting or service memory setting (registration of the features such as “Call Forwarding” and “Speed Dialing” from a station), the data that has been set is invalid. You must execute the system data backup before the following operations.
Page 49 THIS PAGE LEFT BLANK INTENTIONALLY. 2-12 NWA-033623-001 Rev.3.0 91ch2001.fm...
Page 50: Command Description
UNIVERGE SV8300 Command Manual COMMAND DESCRIPTION Chapter This chapter explains the function, precaution, assignment proce- dure and data table of each command. Explanations are given in numerical and alphabetical order of the command code. NWA-033623-001 Rev.3.0 91ch3001.fm...
Page 51: How To Read This Chapter
Chapter 3 COMMAND DESCRIPTION HOW TO READ THIS CHAPTER HOW TO READ THIS CHAPTER HOW TO READ THIS CHAPTER Information about each command is presented in the following order: FUNCTION: The function of the command. PRECAUTION: Precautions related to assigning data. ASSIGNMENT PROCEDURE: The procedure for assigning data in CAT mode.
Page 52 CM00 COMMAND CODE TITLE: SYSTEM DATA MEMORY ALL CLEAR/BILLING MEMORY CLEAR OFF LINE FUNCTION: This command is used to confirm that system data memory (RAM) area can be written-in/read-out, and to assign the default to the RAM area. PRECAUTION: This command can only be used in off-line mode. When this command is executed, “OK”...
Page 53 CM00 COMMAND CODE TITLE: SYSTEM DATA MEMORY ALL CLEAR/BILLING MEMORY CLEAR OFF LINE DATA TABLE: 1ST DATA 2ND DATA DATA MEANING DATA MEANING System data memory all clear Clear SRAM area clear Clear [8300R2] NOTE: Be careful handling CM00>02. Because all stored data in a SRAM area is cleared when the SRAM area memory clear is executed by this command.
Page 54 CM01 COMMAND CODE TITLE: OFF LINE SYSTEM DATA MEMORY PARTIAL CLEAR FUNCTION: This command is used to clear the data for specific features. PRECAUTION: This command can only be used in off-line mode. ASSIGNMENT PROCEDURE: CLEAR DESIGNATION + DE (2/3 digits) DATA TABLE: CLEAR DESIGNATION SYSTEM DATA TO BE CLEARED...
Page 55 CM02 COMMAND CODE TITLE: SETTING OF SYSTEM CLOCK/READING OUT OF DAYLIGHT SAVING TIME FUNCTION: This command is used to assign system clock data (year, date and time). And this command is used to read out of the daylight saving time. PRECAUTION: The system clock starts when is pressed.
Page 56 CM02 COMMAND CODE TITLE: SETTING OF SYSTEM CLOCK/READING OUT OF DAYLIGHT SAVING TIME DATA TABLE: : Default 1ST DATA 2ND DATA DATA MEANING DATA MEANING Setting of Calendar Year YYYY Calendar Year YYYY: Year (2008-2099) NONE No data Setting of Date (Month, Day, Day of Week) MMDDWW Date MM: Month (01-12)
Page 57 CM03 COMMAND CODE TITLE: LOG IN/LOG OUT OF PASSWORD MODE FUNCTION: This command is used to enter a password which allows the authorized personnel to access commands in accordance with preassigned authorization levels. PRECAUTION: The password for each level is set by CME9. The accessible commands for each level is set by CME7.
Page 58: Setting For Each Unit
CM04 TITLE: COMMAND CODE DISPLAY LANGUAGE FOR MULTILINE TERMINAL/DESKCON LCD, DEFAULT SETTING PATTERNS FOR MULTILINE TERMINAL, KIND OF TONE FOR IP STATION/TDM, INQUIRY NO. IN PASSWORD LOCK STATE FOR DT700 SERIES, SINGLE LINE TELEPHONE RINGING SIGNAL FOR STATION-TO-STATION CONNECTION, SINGLE LINE TELEPHONE RINGING SIGNAL FROM A TRUNK, SPECIAL RINGING SIGNAL FOR SINGLE LINE TELEPHONE RING, SETTING OF SERVICES, A-LAW/µ-LAW SETTING FOR EACH UNIT FUNCTION:...
Page 59 CM04 TITLE: COMMAND CODE DISPLAY LANGUAGE FOR MULTILINE TERMINAL/DESKCON LCD, DEFAULT SETTING PATTERNS FOR MULTILINE TERMINAL, KIND OF TONE FOR IP STATION/TDM, INQUIRY NO. IN PASSWORD LOCK STATE FOR DT700 SERIES, SINGLE LINE TELEPHONE RINGING SIGNAL FOR STATION-TO-STATION CONNECTION, SINGLE LINE TELEPHONE RINGING SIGNAL FROM A TRUNK, SPECIAL RINGING SIGNAL FOR SINGLE LINE TELEPHONE RING, SETTING OF SERVICES, A-LAW/µ-LAW SETTING FOR EACH UNIT DATA TABLE:...
Page 60 CM04 TITLE: COMMAND CODE DISPLAY LANGUAGE FOR MULTILINE TERMINAL/DESKCON LCD, DEFAULT SETTING PATTERNS FOR MULTILINE TERMINAL, KIND OF TONE FOR IP STATION/TDM, INQUIRY NO. IN PASSWORD LOCK STATE FOR DT700 SERIES, SINGLE LINE TELEPHONE RINGING SIGNAL FOR STATION-TO-STATION CONNECTION, SINGLE LINE TELEPHONE RINGING SIGNAL FROM A TRUNK, SPECIAL RINGING SIGNAL FOR SINGLE LINE TELEPHONE RING, SETTING OF SERVICES, A-LAW/µ-LAW SETTING FOR EACH UNIT : Default...
Page 61 CM04 TITLE: COMMAND CODE DISPLAY LANGUAGE FOR MULTILINE TERMINAL/DESKCON LCD, DEFAULT SETTING PATTERNS FOR MULTILINE TERMINAL, KIND OF TONE FOR IP STATION/TDM, INQUIRY NO. IN PASSWORD LOCK STATE FOR DT700 SERIES, SINGLE LINE TELEPHONE RINGING SIGNAL FOR STATION-TO-STATION CONNECTION, SINGLE LINE TELEPHONE RINGING SIGNAL FROM A TRUNK, SPECIAL RINGING SIGNAL FOR SINGLE LINE TELEPHONE RING, SETTING OF SERVICES, A-LAW/µ-LAW SETTING FOR EACH UNIT : Default...
Page 62 CM04 TITLE: COMMAND CODE DISPLAY LANGUAGE FOR MULTILINE TERMINAL/DESKCON LCD, DEFAULT SETTING PATTERNS FOR MULTILINE TERMINAL, KIND OF TONE FOR IP STATION/TDM, INQUIRY NO. IN PASSWORD LOCK STATE FOR DT700 SERIES, SINGLE LINE TELEPHONE RINGING SIGNAL FOR STATION-TO-STATION CONNECTION, SINGLE LINE TELEPHONE RINGING SIGNAL FROM A TRUNK, SPECIAL RINGING SIGNAL FOR SINGLE LINE TELEPHONE RING, SETTING OF SERVICES, A-LAW/µ-LAW SETTING FOR EACH UNIT : Default...
Page 63 CM04 TITLE: COMMAND CODE DISPLAY LANGUAGE FOR MULTILINE TERMINAL/DESKCON LCD, DEFAULT SETTING PATTERNS FOR MULTILINE TERMINAL, KIND OF TONE FOR IP STATION/TDM, INQUIRY NO. IN PASSWORD LOCK STATE FOR DT700 SERIES, SINGLE LINE TELEPHONE RINGING SIGNAL FOR STATION-TO-STATION CONNECTION, SINGLE LINE TELEPHONE RINGING SIGNAL FROM A TRUNK, SPECIAL RINGING SIGNAL FOR SINGLE LINE TELEPHONE RING, SETTING OF SERVICES, A-LAW/µ-LAW SETTING FOR EACH UNIT : Default...
Page 64 CM04 TITLE: COMMAND CODE DISPLAY LANGUAGE FOR MULTILINE TERMINAL/DESKCON LCD, DEFAULT SETTING PATTERNS FOR MULTILINE TERMINAL, KIND OF TONE FOR IP STATION/TDM, INQUIRY NO. IN PASSWORD LOCK STATE FOR DT700 SERIES, SINGLE LINE TELEPHONE RINGING SIGNAL FOR STATION-TO-STATION CONNECTION, SINGLE LINE TELEPHONE RINGING SIGNAL FROM A TRUNK, SPECIAL RINGING SIGNAL FOR SINGLE LINE TELEPHONE RING, SETTING OF SERVICES, A-LAW/µ-LAW SETTING FOR EACH UNIT : Default...
Page 65 CM04 TITLE: COMMAND CODE DISPLAY LANGUAGE FOR MULTILINE TERMINAL/DESKCON LCD, DEFAULT SETTING PATTERNS FOR MULTILINE TERMINAL, KIND OF TONE FOR IP STATION/TDM, INQUIRY NO. IN PASSWORD LOCK STATE FOR DT700 SERIES, SINGLE LINE TELEPHONE RINGING SIGNAL FOR STATION-TO-STATION CONNECTION, SINGLE LINE TELEPHONE RINGING SIGNAL FROM A TRUNK, SPECIAL RINGING SIGNAL FOR SINGLE LINE TELEPHONE RING, SETTING OF SERVICES, A-LAW/µ-LAW SETTING FOR EACH UNIT : Default...
Page 66 CM04 TITLE: COMMAND CODE DISPLAY LANGUAGE FOR MULTILINE TERMINAL/DESKCON LCD, DEFAULT SETTING PATTERNS FOR MULTILINE TERMINAL, KIND OF TONE FOR IP STATION/TDM, INQUIRY NO. IN PASSWORD LOCK STATE FOR DT700 SERIES, SINGLE LINE TELEPHONE RINGING SIGNAL FOR STATION-TO-STATION CONNECTION, SINGLE LINE TELEPHONE RINGING SIGNAL FROM A TRUNK, SPECIAL RINGING SIGNAL FOR SINGLE LINE TELEPHONE RING, SETTING OF SERVICES, A-LAW/µ-LAW SETTING FOR EACH UNIT : Default...
Page 67 CM04 TITLE: COMMAND CODE DISPLAY LANGUAGE FOR MULTILINE TERMINAL/DESKCON LCD, DEFAULT SETTING PATTERNS FOR MULTILINE TERMINAL, KIND OF TONE FOR IP STATION/TDM, INQUIRY NO. IN PASSWORD LOCK STATE FOR DT700 SERIES, SINGLE LINE TELEPHONE RINGING SIGNAL FOR STATION-TO-STATION CONNECTION, SINGLE LINE TELEPHONE RINGING SIGNAL FROM A TRUNK, SPECIAL RINGING SIGNAL FOR SINGLE LINE TELEPHONE RING, SETTING OF SERVICES, A-LAW/µ-LAW SETTING FOR EACH UNIT : Default...
Page 68 CM04 TITLE: COMMAND CODE DISPLAY LANGUAGE FOR MULTILINE TERMINAL/DESKCON LCD, DEFAULT SETTING PATTERNS FOR MULTILINE TERMINAL, KIND OF TONE FOR IP STATION/TDM, INQUIRY NO. IN PASSWORD LOCK STATE FOR DT700 SERIES, SINGLE LINE TELEPHONE RINGING SIGNAL FOR STATION-TO-STATION CONNECTION, SINGLE LINE TELEPHONE RINGING SIGNAL FROM A TRUNK, SPECIAL RINGING SIGNAL FOR SINGLE LINE TELEPHONE RING, SETTING OF SERVICES, A-LAW/µ-LAW SETTING FOR EACH UNIT : Default...
Page 69 CM04 TITLE: COMMAND CODE DISPLAY LANGUAGE FOR MULTILINE TERMINAL/DESKCON LCD, DEFAULT SETTING PATTERNS FOR MULTILINE TERMINAL, KIND OF TONE FOR IP STATION/TDM, INQUIRY NO. IN PASSWORD LOCK STATE FOR DT700 SERIES, SINGLE LINE TELEPHONE RINGING SIGNAL FOR STATION-TO-STATION CONNECTION, SINGLE LINE TELEPHONE RINGING SIGNAL FROM A TRUNK, SPECIAL RINGING SIGNAL FOR SINGLE LINE TELEPHONE RING, SETTING OF SERVICES, A-LAW/µ-LAW SETTING FOR EACH UNIT : Default...
Page 70 CM04 TITLE: COMMAND CODE DISPLAY LANGUAGE FOR MULTILINE TERMINAL/DESKCON LCD, DEFAULT SETTING PATTERNS FOR MULTILINE TERMINAL, KIND OF TONE FOR IP STATION/TDM, INQUIRY NO. IN PASSWORD LOCK STATE FOR DT700 SERIES, SINGLE LINE TELEPHONE RINGING SIGNAL FOR STATION-TO-STATION CONNECTION, SINGLE LINE TELEPHONE RINGING SIGNAL FROM A TRUNK, SPECIAL RINGING SIGNAL FOR SINGLE LINE TELEPHONE RING, SETTING OF SERVICES, A-LAW/µ-LAW SETTING FOR EACH UNIT Fixed pattern and Programmable pattern...
Page 71 CM04 TITLE: COMMAND CODE DISPLAY LANGUAGE FOR MULTILINE TERMINAL/DESKCON LCD, DEFAULT SETTING PATTERNS FOR MULTILINE TERMINAL, KIND OF TONE FOR IP STATION/TDM, INQUIRY NO. IN PASSWORD LOCK STATE FOR DT700 SERIES, SINGLE LINE TELEPHONE RINGING SIGNAL FOR STATION-TO-STATION CONNECTION, SINGLE LINE TELEPHONE RINGING SIGNAL FROM A TRUNK, SPECIAL RINGING SIGNAL FOR SINGLE LINE TELEPHONE RING, SETTING OF SERVICES, A-LAW/µ-LAW SETTING FOR EACH UNIT •...
Page 72 CM04 TITLE: COMMAND CODE DISPLAY LANGUAGE FOR MULTILINE TERMINAL/DESKCON LCD, DEFAULT SETTING PATTERNS FOR MULTILINE TERMINAL, KIND OF TONE FOR IP STATION/TDM, INQUIRY NO. IN PASSWORD LOCK STATE FOR DT700 SERIES, SINGLE LINE TELEPHONE RINGING SIGNAL FOR STATION-TO-STATION CONNECTION, SINGLE LINE TELEPHONE RINGING SIGNAL FROM A TRUNK, SPECIAL RINGING SIGNAL FOR SINGLE LINE TELEPHONE RING, SETTING OF SERVICES, A-LAW/µ-LAW SETTING FOR EACH UNIT •...
Page 73 CM04 TITLE: COMMAND CODE DISPLAY LANGUAGE FOR MULTILINE TERMINAL/DESKCON LCD, DEFAULT SETTING PATTERNS FOR MULTILINE TERMINAL, KIND OF TONE FOR IP STATION/TDM, INQUIRY NO. IN PASSWORD LOCK STATE FOR DT700 SERIES, SINGLE LINE TELEPHONE RINGING SIGNAL FOR STATION-TO-STATION CONNECTION, SINGLE LINE TELEPHONE RINGING SIGNAL FROM A TRUNK, SPECIAL RINGING SIGNAL FOR SINGLE LINE TELEPHONE RING, SETTING OF SERVICES, A-LAW/µ-LAW SETTING FOR EACH UNIT •...
Page 74 CM05 COMMAND CODE TITLE: BLADE RESET BLADE TYPE, TRUNK BLADE NUMBER FUNCTION: This command is used to designate the type of blade installed. PRECAUTION: This command requires a blade reset after data setting. ASSIGNMENT PROCEDURE: UNIT/SLOT NUMBER DATA ST + + DE (4 digits) (2-3 digits)
Page 75 CM05 COMMAND CODE TITLE: BLADE TYPE, TRUNK BLADE NUMBER BLADE RESET 1ST DATA 2ND DATA RELATED COMMAND MEANING DATA MEANING DATA MEANING Blade Type XX ZZ XX : Unit No. (01-50) LD Trunk Blade ZZ : Slot No. (01-18) (CD-4DIOPA) “About Unit Basic Rate (2B + D) number, Slot number...
Page 76 CM05 COMMAND CODE TITLE: BLADE TYPE, TRUNK BLADE NUMBER BLADE RESET : Default 1ST DATA 2ND DATA RELATED COMMAND MEANING DATA MEANING DATA MEANING Blade Type XX ZZ XX : Unit No. (01-50) In-Skin UMS Blade ZZ : Slot No. (01-18) (CD-VM00) “About Unit Conference Blade...
Page 77 CM08 COMMAND CODE TITLE: BASIC SERVICES FUNCTION: This command is used to assign basic features on a system wide basis. PRECAUTION: After setting 1st data 335, 368, 390, 391, 392, 396, 397, 420, 592, 909, system reset is required. ASSIGNMENT PROCEDURE: BASIC SERVICE DATA (0/1) + 08 +...
Page 78 CM08 COMMAND CODE TITLE: BASIC SERVICES : Default BASIC SERVICE SETTING DATA C.O. to C.O. transfer by station or attendant To allow NOTE: Not allowed This data is effective for C.O. trunks (Ground Start/ Loop Start) which receive a release signal from the C.O.
Page 79 CM08 COMMAND CODE TITLE: BASIC SERVICES : Default BASIC SERVICE SETTING DATA Warning Tone sent to connected parties to alert Executive Right Not sent of Way, Busy Verification or Attendant Override To send • Three burst tone [Other than New Zealand] •...
Page 80 CM08 COMMAND CODE TITLE: BASIC SERVICES : Default BASIC SERVICE SETTING DATA Toll Restriction-Total Digit Count for PB to PB/DP to PB Con- To provide nection Not provided [Not used in North America] Trunk seizure sequence when CM35 Y=083: 0 Highest available trunk NOTE: Lowest available trunk...
Page 81 CM08 COMMAND CODE TITLE: BASIC SERVICES BASIC SERVICE: 101-199 : Default BASIC SERVICE SETTING DATA When CM08>102: 0 for Single Line Telephone The call with STA-B is disconnected, and STA-A returns to STA-C Three Party Conference When the station (STA-A), after holding the other station (STA- As per CM08>101 C), has made a switch hook flash while talking with another sta- STA-B is held, and STA-A returns to...
Page 82 CM08 COMMAND CODE TITLE: BASIC SERVICES : Default BASIC SERVICE SETTING DATA While the station (STA-A) is talking with another station (STA- STA-A returns to the call with C.O. B) after consultation hold with a C.O. call, when STA-B has line hung up STA-A hears ROT...
Page 83 CM08 COMMAND CODE TITLE: BASIC SERVICES : Default BASIC SERVICE SETTING DATA A trunk line placed in Consultation Hold by Call Park-System/ Not available Tenant, can be retrieved by pressing trunk line appearance key Available on Multiline Terminal Periodic Time Indication Tone sending for C.O. Line connec- To send tion CM41 Y=0>09...
Page 84 CM08 COMMAND CODE TITLE: BASIC SERVICES : Default BASIC SERVICE SETTING DATA Attendant access capability from the stations belonging to a To allow tenant with no Attendant Console Not allowed [8300R2] CM62 Individual attendant access from a station within another tenant Restricted [8300R2] CM20>A095...
Page 85 CM08 COMMAND CODE TITLE: BASIC SERVICES : Default BASIC SERVICE SETTING DATA Whether dialing digit “1” upon encountering trunk busy is Effective as switch hook flash effective as switch hook flash. (For DP telephone) Ineffective NOTE: Effective only when CM08>151: 1. Dialing of a Single Digit Feature Access Code while the calling Available station hears RBT, or performs a Voice Call...
Page 86 CM08 COMMAND CODE TITLE: BASIC SERVICES : Default BASIC SERVICE SETTING DATA Multiple Radio Paging access after accessing a Radio Paging Not available trunk with delay type Radio Paging Available NOTE: This is ineffective when CM08>157: 0. Step Call for an incoming call from a Tie Line Not available Available Replay timer for Attendant Delay Announcement...
Page 87 CM08 COMMAND CODE TITLE: BASIC SERVICES : Default BASIC SERVICE SETTING DATA When the transferring station goes on-hook before the called Not available station answers for Call Transfer-All Calls service, if the trans- Available ferred call remains unanswered for a preprogrammed duration, the transferring station is recalled.
Page 88 CM08 COMMAND CODE TITLE: BASIC SERVICES BASIC SERVICE: 200-294 : Default BASIC SERVICE SETTING DATA Wake-up time printout on Hotel printer and the report is sent to Available PMS, when setting wake-up time from guest station Not available Do Not Disturb records print on Hotel printer and the report is Available sent to PMS, when setting Do Not Disturb from guest station Not available...
Page 89 CM08 COMMAND CODE TITLE: BASIC SERVICES : Default BASIC SERVICE SETTING DATA Dialing of a Single Digit Feature Access Code, while the calling Available station hears busy tone Not available To activate Single Digit Feature Access Code, set CM08>050, 051, 069 and 148 to “1”. If the * button on a DTMF telephone is pressed while hearing busy tone, it is Ineffective regarded as a Switch Hook Flash...
Page 90 CM08 COMMAND CODE TITLE: BASIC SERVICES : Default BASIC SERVICE SETTING DATA When a caller encounters all ACD/UCD stations busy Busy Tone is to be sent out Caller is placed into queuing mode Method to cancel Call Forwarding-All Calls/-Busy Line/-No Feature access code + Feature key Answer Feature access code + “*”...
Page 91 CM08 COMMAND CODE TITLE: BASIC SERVICES : Default BASIC SERVICE SETTING DATA To complete the operation for setting Call Forwarding-All Setting when the station goes on Calls-Outside/Busy Line-Outside/No Answer-Outside hook/when receiving Service Set Tone (ORT time out) Setting when receiving Service Set Tone (ORT time out) Whether the transferred C.O.
Page 92 CM08 COMMAND CODE TITLE: BASIC SERVICES : Default BASIC SERVICE SETTING DATA Dial Intercom to station set for Do Not Disturb Restricted (ROT connection) Allowed Call Forwarding-Busy Line/Station Hunting for station with Do Allowed Not Disturb set Restricted (ROT connection) Destination of call transfer by CM51 Y=10 in a system with The call is routed to a station within multiple-tenants, when a station/DID/Tie Line call from another...
Page 93 CM08 COMMAND CODE TITLE: BASIC SERVICES : Default BASIC SERVICE SETTING DATA Whether the Hold key of the Multiline Terminal is used as the Call Park-Tenant Set key Call Park-Tenant Set key for an internal or external call Hold key When the temporary service class returns to proper service class When called number has been dialed (Forced Account Code and Authorization Code)
Page 94 CM08 COMMAND CODE TITLE: BASIC SERVICES : Default BASIC SERVICE SETTING DATA Call termination to My Line while the station user makes a call Restricted with a Sub line or trunk line on Multiline Terminal NOTE 1 Allowed Busy indication on BLF of large type DESKCON, DSS Con- Station base sole or Multiline Terminal by station base or extension base Extension base...
Page 95 CM08 COMMAND CODE TITLE: BASIC SERVICES : Default BASIC SERVICE SETTING DATA Room Cutoff Not Allowed To allow Wake Up time display on Front Desk Terminal 24-Hour (Military format) 12-Hour MW lamp indication on Multiline Terminal to which Message Flashing (60 IPM) Waiting/Message Reminder is set Steady lighting Continued on next page...
Page 96 CM08 COMMAND CODE TITLE: BASIC SERVICES BASIC SERVICE: 301-398 : Default BASIC SERVICE SETTING DATA When system is reseted Multiline Terminal MIC lamp ON Multiline Terminal MIC lamp OFF Display last calling station number 6 seconds Until next call Display calling station number when a calling station abandons Not available a call before the call is answered Available...
Page 97 CM08 COMMAND CODE TITLE: BASIC SERVICES : Default BASIC SERVICE SETTING DATA When a call is transferred by Remote Access to System (DISA) Disconnect call to predetermined station and time-out occurs, the call is contin- Continue call ued or dropped CM30 Y=30 CM41 Y=0>39 Buzzer sound when terminating incoming call to attendant that Not provided...
Page 98 CM08 COMMAND CODE TITLE: BASIC SERVICES : Default BASIC SERVICE SETTING DATA Call Forwarding Override-CCIS Not available (BT connection) Available Alternative Routing when outgoing trunks of tandem office are Available all busy/Alternate Routing for multiple SIP Not available Send Call Forwarding station information through CCIS To send Not sent When forwarded call is terminated to VMS via CCIS, whether...
Page 99 CM08 COMMAND CODE TITLE: BASIC SERVICES : Default BASIC SERVICE SETTING DATA Holding/held party control for Music on Hold tenant basis Held party control (tenant) Holding party control (tenant) Multiline Terminal tone ringer selection By pressing Feature key and dialing 3 NOTE 1 RESET As per CM15 Y=083, 084, 093,...
Page 100 CM08 COMMAND CODE TITLE: BASIC SERVICES : Default BASIC SERVICE SETTING DATA Multiline Terminal ringing signal patterns for an internal/exter- Depends on the combination of nal call and special ringing CM08>392 and 396 [Not used in North America] (See the following table) Depends on the data set by RESET CM08>392 and 396...
Page 101 CM08 COMMAND CODE TITLE: BASIC SERVICES : Default BASIC SERVICE SETTING DATA Provide PAD for Multiline Terminal at all times To provide NOTE: For Europe, be sure to set the data to 0. Not provided Multiline Terminal connection PAD With PAD [For EU] Without PAD NOTE 1:...
Page 102 CM08 COMMAND CODE TITLE: BASIC SERVICES BASIC SERVICE: 400-489 : Default BASIC SERVICE SETTING DATA Send Calling Party Subaddress to ISDN network To send Not sent Terminating system for Called Party Subaddress Station call Terminating system assigned by CM30 Y=02/03/40/41 Advice of Charge (AOC) display on Multiline Terminal when Flashing display the charge has been summed over $9999.99/€...
Page 103 CM08 COMMAND CODE TITLE: BASIC SERVICES : Default BASIC SERVICE SETTING DATA Charging to the transferring station or transfer destination sta- Charging to transferring station tion Charging to transfer destination sta- tion Shown below are stations to which call is to be charged in the case of various transfer patterns. STA: station DESKCON: Desk Console Transfer Pattern...
Page 104 CM08 COMMAND CODE TITLE: BASIC SERVICES : Default BASIC SERVICE SETTING DATA Forced release when called ISDN Telephone does not answer Not available during 3 minutes Available ISDN CPN (Calling Party Number) when making a call from CPN entered in ISDN Telephone ISDN Telephone CPN assigned by CM12 Y=12/13 Recall display on Attendant Console...
Page 105 CM08 COMMAND CODE TITLE: BASIC SERVICES : Default BASIC SERVICE SETTING DATA Send ANI/Caller ID/CPN to SMDR terminal Available Not available OAI TSAPI Same as 2400 IPX system (recom- SCF facility mended setting) SMFN Off-Hook indication sent SCF error code type SCF error Detail SCF error Kind Method of readout the traffic information...
Page 106 Protected Login Mode for All IP Sta- tions As per CM15 Y=480 Whether the system encodes the station number when IP Sta- To encode (NEC Original method) tions login to the network Not encoded Whether the system encodes the password when IP Stations...
Page 107 : Default BASIC SERVICE SETTING DATA Encoding method for the password NOTE: NEC Original method Effective when CM08>515 is set to 1. Whether the system sends SPDT when entering the name/num- Not sent ber for Dial by Name To send...
Page 108 CM08 COMMAND CODE TITLE: BASIC SERVICES : Default BASIC SERVICE SETTING DATA Whether the step call is to be restricted or not Restricted Allow Selection of the Guest information displayed on an administra- Display PMS information A/B tive station (Multiline Terminal/Attendant Console) for 8 char- Display VIP/language acters display in left-side on upper line of LCD Whether the PMS information for 8 characters display in left-...
Page 109 CM08 COMMAND CODE TITLE: BASIC SERVICES : Default BASIC SERVICE SETTING DATA Information to display on the middle line of the Multiline Ter- Forwarding station name minal/DESKCON LCD when forwarding a trunk call to the Caller ID Multiline Terminal/DESKCON by Call Forwarding-All Calls/ (Calling number/Calling name) No Answer/Busy Line/Not Available Display the first forwarding station number via CCIS or the...
Page 110 CM08 COMMAND CODE TITLE: BASIC SERVICES : Default BASIC SERVICE SETTING DATA Whether the service which is set to a group member station is Effective effective when the group members are called by Group Feature Ineffective NOTE: When the second data of CM08>585 is set to 0, the following services are effective. Call Forwarding-All Calls/Split Call Forwarding-All Calls/Call Forwarding-All Calls of Mobility Access/Do Not Disturb/Transfer the call to station set Do Not Disturb (CM51 Y=10)/Call Forwarding- Logout...
Page 111 CM08 COMMAND CODE TITLE: BASIC SERVICES BASIC SERVICE: 600-699 : Default BASIC SERVICE SETTING DATA Selection of trunk route seized for Call Forwarding-All Calls/ By calling party’s tenant/terminating Busy Line/No Answer-Outside, Split Call Forwarding-All trunk’s tenant Calls/Busy Line/No Answer-Outside By Call Forwarding setting station’s tenant Reset of Queue Limit counter for TAS per tenant Not provided...
Page 112 CM08 COMMAND CODE TITLE: BASIC SERVICES : Default BASIC SERVICE SETTING DATA Connected line number indication on DESKCON display in Not provided ETSI ISDN Connected Line Identification Presentation (COLP) To provide [For EU] Trunk access code display when a call terminates via ETSI Available ISDN Not available...
Page 113 CM08 COMMAND CODE TITLE: BASIC SERVICES : Default BASIC SERVICE SETTING DATA Output message which is sent from PBX to ISDN network CALL PROC + ALERT + DISC when the 2nd line is released by Mobility Access hooking CALL PROC + ALERT + NOTE: This data is effective only when the 2nd data of CONNECT + DISC...
Page 114 CM08 COMMAND CODE TITLE: BASIC SERVICES BASIC SERVICE: 702-732 : Default BASIC SERVICE SETTING DATA Ringing signal/Live Record Start signal which includes caller To send information (such as station number and kind of calling party) Not sent is sent to VMS NOTE: Set the second data to “0”...
Page 115 CM08 COMMAND CODE TITLE: BASIC SERVICES : Default BASIC SERVICE SETTING DATA Whether to link with a VMS soft key feature (CM13 Y=37)/ Only as per CM13 Y=37/CM08>702 expand AAINFO (CM08>702) As per CM13 Y=37/CM08>702 and expansion information sent to VMS Station number sent to VMS when accessing VMS from a sub- Subline station number line assigned on Multiline Terminal...
Page 116 CM08 COMMAND CODE TITLE: BASIC SERVICES BASIC SERVICE: 801-898 : Default BASIC SERVICE SETTING DATA Send Office Number to Center Office for Centralized Billing- To send CCIS Not sent NOTE: When the network adopts Open Numbering Plan, set the office number by CMA7 Y=06. When the network adopts Closed Numbering Plan, set the office number by CMA7 Y=07.
Page 117 CM08 COMMAND CODE TITLE: BASIC SERVICES : Default BASIC SERVICE SETTING DATA OAI SMFN STS (status) when the forwarded call with Call SMFN STS=4/5/6 Forwarding-All Calls/Busy Line/No Answer is terminated to a SMFN STS=0 station via CCIS (SMFN FID=1) OAI SMFN STS (status) when a station answers via CCIS the SMFN STS=5/6/7 forwarded call with Call Forwarding-All Calls/Busy Line/No SMFN STS=0...
Page 118 CM08 COMMAND CODE TITLE: BASIC SERVICES : Default BASIC SERVICE SETTING DATA Kind of Center Office for Centralized Billing-CCIS SV8300 2400 IPX NOTE 1: Set this data to the Local Office of the Centralized Billing-CCIS. This data setting is not required for Center Office.
Page 119 CM08 COMMAND CODE TITLE: BASIC SERVICES : Default BASIC SERVICE SETTING DATA Setting CAMP ON to the destination when Call Forwarding-All To set Calls is set by SCF FID=19 Not set Send OAI SMFN when setting CAMP ON of OAI SMFN To send FID=6 STS (status)=3 for the Call Hold status Not sent...
Page 120 CM08 COMMAND CODE TITLE: BASIC SERVICES : Default BASIC SERVICE SETTING DATA Printing way of Automatic Wake Up for an individual station To print process and result execution To print only result NOTE: When the second data is set to 1, the record of the start of calling/the called station is busy/re-calling is also printed.
Page 121 CM08 COMMAND CODE TITLE: BASIC SERVICES : Default BASIC SERVICE SETTING DATA Setting of number of sending digits for printer Printer for 80 digits [8300R2] Printer for 20 digits Whether to give ACC/AUTH for Station Individual Call To give Record Print Not given [8300R2] Setting of decimals for Call charge...
Page 122 CM08 COMMAND CODE TITLE: BASIC SERVICES BASIC SERVICE: 909 : Default BASIC SERVICE SETTING DATA Allow built-in modem/speech synthesis service Allow Restricted RESET 3-73 NWA-033623-001 Rev.3.0 91ch3001.fm NOVEMBER/12/2008...
Page 123 CM0B COMMAND CODE TITLE: RESET LAN DATA ASSIGNMENT FUNCTION: This command is used to assign the LAN data for Maintenance port of CPU blade and VOIP port of VoIPDB. Set each port by the operational pattern to be used. For details, refer to PRECAUTION (1) on this page.
Page 124 CM0B COMMAND CODE TITLE: RESET LAN DATA ASSIGNMENT There are the following conditions when setting the Default Gateway Address by this command. • Only one default gateway address can be set for the system. • Set the Default Gateway Address to the Maintenance port (Y=0XX) when not using VoIPDB. •...
Page 125 CM0B COMMAND CODE TITLE: RESET LAN DATA ASSIGNMENT DATA TABLE: Y=0XX : Default 1ST DATA 2ND DATA RELATED COMMAND MEANING DATA MEANING DATA MEANING 0XX 0 : Maintenance Port IP Address for the sys- XXX.XX IP Address XX: Unit No. (01-50) ...X (Maximum 15 digits) XXX.XXX.XXX.XXX=...
Page 126 CM0B COMMAND CODE TITLE: RESET LAN DATA ASSIGNMENT : Default 1ST DATA 2ND DATA RELATED COMMAND MEANING DATA MEANING DATA MEANING 0XX 0 : Maintenance Port Whether to allow the Restricted XX: Unit No. (01-50) connection with PCPro Allow OAI Port number OAI port number 1024 OAI port number 1025 OAI port number 1039...
Page 127 CM0B COMMAND CODE TITLE: RESET LAN DATA ASSIGNMENT : Default 1ST DATA 2ND DATA RELATED COMMAND MEANING DATA MEANING DATA MEANING 0XX 0 : Maintenance Port SNMP port Open SNMP port XX: Unit No. (01-50) Not open SNMP port NOTE: Only Unit No.
Page 128 CM0B COMMAND CODE TITLE: RESET LAN DATA ASSIGNMENT : Default 1ST DATA 2ND DATA RELATED COMMAND MEANING DATA MEANING DATA MEANING 0XX 0 : Maintenance Port Contact with the system XX...X Character manager (sysContact) (Maximum 64 characters) XX: Unit No. (01-50) NOTE NONE No data...
Page 129 CM0B COMMAND CODE TITLE: RESET LAN DATA ASSIGNMENT : Default 1ST DATA 2ND DATA RELATED COMMAND MEANING DATA MEANING DATA MEANING 0XX 0 : Maintenance Port IP Address for the desti- XXX.XX IP Address for the destina- XX: Unit No. (01-50) nation of trap ...X tion of trap...
Page 130 CM0B COMMAND CODE TITLE: RESET LAN DATA ASSIGNMENT : Default 1ST DATA 2ND DATA RELATED COMMAND MEANING DATA MEANING DATA MEANING 0XX 0 : Maintenance Port Required IP Address for XXX.XX IP Address for the SNMP XX: Unit No. (01-50) the SNMP manager ...X manager...
Page 131 CM0B COMMAND CODE TITLE: RESET LAN DATA ASSIGNMENT Y=1XX : Default 1ST DATA 2ND DATA RELATED COMMAND MEANING DATA MEANING DATA MEANING 1XX 1 : VOIP Port IP Address for the sys- XXX.XX IP Address XX: Unit No. (01-50) ...X (Maximum 15 digits) XXX.XXX.XXX.XXX= 0.0.0.1-255.255.255.254...
Page 132 CM0B COMMAND CODE TITLE: LAN DATA ASSIGNMENT RESET : Default 1ST DATA 2ND DATA RELATED COMMAND MEANING DATA MEANING DATA MEANING 1XX 1 : VOIP Port Location number for sta- Location number 00 XX: Unit No. (01-50) tions accommodated in Location number 63 the Unit Location number 00...
Page 133 CM0B COMMAND CODE TITLE: RESET LAN DATA ASSIGNMENT : Default 1ST DATA 2ND DATA RELATED COMMAND MEANING DATA MEANING DATA MEANING 1XX 1 : VOIP Port UDP Port for IP Multi- 01024 TCP/UDP/RTP Port num- XX: Unit No. (01-50) line Terminal voice con- 65534 trol NONE...
Page 134 CM0B COMMAND CODE TITLE: RESET LAN DATA ASSIGNMENT : Default 1ST DATA 2ND DATA RELATED COMMAND MEANING DATA MEANING DATA MEANING 1XX 1 : VOIP Port OAI Port number OAI port number 1024 XX: Unit No. (01-50) OAI port number 1025 OAI port number 1039 OAI port number 60030 NOTE:...
Page 135 CM0B COMMAND CODE TITLE: RESET LAN DATA ASSIGNMENT : Default 1ST DATA 2ND DATA RELATED COMMAND MEANING DATA MEANING DATA MEANING 1XX 1 : VOIP Port Query interval to a DNS 0001 1 minute XX: Unit No. (01-50) server (1 minute increments) 1440 14440 minutes NONE...
Page 136 CM0B COMMAND CODE TITLE: LAN DATA ASSIGNMENT RESET : Default 1ST DATA 2ND DATA RELATED COMMAND MEANING DATA MEANING DATA MEANING 1XX 1 : VOIP Port Start time for the auto- Not execute the automatic XX: Unit No. (01-50) matic changeover to nor- changeover to normal mal mode from survival mode...
Page 137 CM0B COMMAND CODE TITLE: RESET LAN DATA ASSIGNMENT : Default 1ST DATA 2ND DATA RELATED COMMAND MEANING DATA MEANING DATA MEANING 1XX 1 : VOIP Port SNMP port Open SNMP port XX: Unit No. (01-50) Not open SNMP port NOTE: Only Unit No.
Page 138 CM0B COMMAND CODE TITLE: RESET LAN DATA ASSIGNMENT : Default 1ST DATA 2ND DATA RELATED COMMAND MEANING DATA MEANING DATA MEANING 1XX 1 : VOIP Port Contact with the system XX...X Character manager (sysContact) (Maximum 64 characters) XX: Unit No. (01-50) NOTE NONE No data...
Page 139 CM0B COMMAND CODE TITLE: RESET LAN DATA ASSIGNMENT : Default 1ST DATA 2ND DATA RELATED COMMAND MEANING DATA MEANING DATA MEANING 1XX 1 : VOIP Port IP Address for the desti- XXX.XX IP Address for the destina- XX: Unit No. (01-50) nation of trap ...X tion of trap...
Page 140 CM0B COMMAND CODE TITLE: RESET LAN DATA ASSIGNMENT : Default 1ST DATA 2ND DATA RELATED COMMAND MEANING DATA MEANING DATA MEANING 1XX 1 : VOIP Port Required IP Address for XXX.XX IP Address for the SNMP XX: Unit No. (01-50) the SNMP manager ...X manager...
Page 141 CM0B COMMAND CODE TITLE: RESET LAN DATA ASSIGNMENT Y=2XX : Default 1ST DATA 2ND DATA RELATED COMMAND MEANING DATA MEANING DATA MEANING 2XX 2 : VOIP Port IP Address 1 (RTP) for XXX.XX IP Address XX: Unit No. (01-50) VoIPDB ...X (Maximum 15 digits) XXX.XXX.XXX.XXX=...
Page 142 CM0B COMMAND CODE TITLE: LAN DATA ASSIGNMENT RESET : Default 1ST DATA 2ND DATA RELATED COMMAND MEANING DATA MEANING DATA MEANING 2XX 2 : VOIP Port IP Address 2 (RTP) for XXX.XX IP Address XX: Unit No. (01-50) VoIPDB ...X (Maximum 15 digits) NOTE 1, NOTE 2 XXX.XXX.XXX.XXX=...
Page 143 CM0B COMMAND CODE TITLE: RESET LAN DATA ASSIGNMENT : Default 1ST DATA 2ND DATA RELATED COMMAND MEANING DATA MEANING DATA MEANING 2XX 2 : VOIP Port RTP Base Port for Voice 01024 RTP Port number CMA7 Y=46 XX: Unit No. (01-50) Packet transmitting/ CMBA receiving...
Page 144 CM0B COMMAND CODE TITLE: RESET LAN DATA ASSIGNMENT Y=000 : Default 1ST DATA 2ND DATA RELATED COMMAND MEANING DATA MEANING DATA MEANING 000 Unit number setting – Unit No. 01 OFF LINE Unit No. 50 NONE Unit No. 01 NOTE 1: This command should be set in each unit.
Page 145 CM0C COMMAND CODE TITLE: UPDATING OF IP STATION FIRMWARE/REMOTE SYSTEM UPGRADE FUNCTION: This command is used to specify the update information of IP Station firmware and Remote System Up- grade. PRECAUTION: None ASSIGNMENT PROCEDURE: 1ST DATA 2ND DATA + 0CYY + (1-8 digits) (1-12 digits) DATA TABLE:...
Page 146 CM0C COMMAND CODE TITLE: UPDATING OF IP STATION FIRMWARE/REMOTE SYSTEM UPGRADE : Default 1ST DATA 2ND DATA MEANING DATA MEANING DATA MEANING Update information Firmware file ver- AABBCCDD AA : Integral No. of file version Profile No. sion for update (For SIP Multi- (00-99) line Terminal)
Page 147 CM0C COMMAND CODE TITLE: UPDATING OF IP STATION FIRMWARE/REMOTE SYSTEM UPGRADE : Default 1ST DATA 2ND DATA MEANING DATA MEANING DATA MEANING Information of XX01 Port number for 00001 TCP Port No. for the FTP server Remote System FTP server Upgrade (Main Unit/ 65534 Remote Unit)
Page 148 CM0C COMMAND CODE TITLE: UPDATING OF IP STATION FIRMWARE/REMOTE SYSTEM UPGRADE : Default 1ST DATA 2ND DATA MEANING DATA MEANING DATA MEANING Information of XX04 Directory name XXX...X Directory name Remote System (Maximum 32 characters) Upgrade (Main Unit/ XX: 01-04: Main Clear Remote Unit) Unit No.
Page 149 CM0C COMMAND CODE TITLE: UPDATING OF IP STATION FIRMWARE/REMOTE SYSTEM UPGRADE 1ST DATA 2ND DATA MEANING DATA MEANING DATA MEANING Start updating IP IP Station No. Start updating Station firmware XXXXXXXX NOTE: After setting the first data and second data, PCPro/CAT displays the status of the IP Station. The table below shows the contents of the display and its meaning.
Page 150 CM0C COMMAND CODE TITLE: UPDATING OF IP STATION FIRMWARE/REMOTE SYSTEM UPGRADE : Default 1ST DATA 2ND DATA MEANING DATA MEANING DATA MEANING Remote System XX00 Execute CPU pro- Start to download Upgrade (Main Unit/ gram download Now downloading Remote Unit) Not executed XX: 01-04: Main YYYY MM...
Page 151 CM0C COMMAND CODE TITLE: UPDATING OF IP STATION FIRMWARE/REMOTE SYSTEM UPGRADE : Default 1ST DATA 2ND DATA MEANING DATA MEANING DATA MEANING Remote System XX01 Changeover YYYY MM YYYY: Year (2008-2099) Upgrade (Main Unit/ (changeback) DD HH mm : Month (01-12) Remote Unit) time : Date (01-31)
Page 152 CM0C COMMAND CODE TITLE: UPDATING OF IP STATION FIRMWARE/REMOTE SYSTEM UPGRADE : Default 1ST DATA 2ND DATA MEANING DATA MEANING DATA MEANING Remote System XX05 The latest result XX YY ZZ XX: File type Upgrade (Main Unit/ of CPU program YYYYMMDD 00: CPU program file Remote Unit)
Page 153 CM10 COMMAND CODE TITLE: STATION NUMBER, TRUNK NUMBER, BLADE NUMBER FUNCTION: This command is used to assign station numbers, trunk numbers, and blade numbers to Physical Port No. (Unit No. + Slot No. + Circuit No.)/Virtual Port No.. PRECAUTION: When deleting a station number (Single Line or Multiline Terminal), be sure to delete Call Pickup data (CM16), ACD/UCD Group data (CM17) and Station Hunting Group data (CM18) in advance.
Page 154 CM10 COMMAND CODE TITLE: STATION NUMBER, TRUNK NUMBER, BLADE NUMBER 1ST DATA 2ND DATA RELATED COMMAND MEANING DATA MEANING DATA MEANING TDM terminal/Trunk XXYYZZ Physical Port num- D000 Trunk number (C.O./Tie CM30 registration Line, Paging, Radio Paging,) CM35 D511 “About Unit XX: Unit number NOTE 1: Do not assign...
Page 155 CM10 COMMAND CODE TITLE: STATION NUMBER, TRUNK NUMBER, BLADE NUMBER : Default 1ST DATA 2ND DATA RELATED COMMAND MEANING DATA MEANING DATA MEANING TDM terminal regis- XXYYZZ Physical Port num- EC00 Add-on Module number CM90 tration NOTE: The same number CM98 “About Unit XX: Unit number...
Page 156 CM10 COMMAND CODE TITLE: STATION NUMBER, TRUNK NUMBER, BLADE NUMBER : Default 1ST DATA 2ND DATA RELATED COMMAND MEANING DATA MEANING DATA MEANING IP terminal registra- 0000 Virtual Port num- IP Station number tion ber. (for IP termi- X: 0-9, A (*), B (#) 1499 nal) XXXX...
Page 157 CM10 COMMAND CODE TITLE: STATION NUMBER, TRUNK NUMBER, BLADE NUMBER : Default 1ST DATA 2ND DATA RELATED COMMAND MEANING DATA MEANING DATA MEANING IPT (P2P CCIS) regis- Virtual Port num- D000 Trunk No. tration ber (for IPT [P2P CCIS]) D511 IPT (P2P CCIS) RESET NONE No data...
Page 158: Unit Configuration
CM10 COMMAND CODE TITLE: STATION NUMBER, TRUNK NUMBER, BLADE NUMBER About Unit number, Slot number and Circuit number The following describes the Unit number, Slot number and Circuit number that are set by CM05 and CM10. Unit Number The Unit means the Main Unit that consists of CPU chassis (1U) and Line/Trunk chassis (2U). Up to a maximum of 50 Units can be installed, and each Unit is managed by the Unit number.
Page 159 CM10 COMMAND CODE TITLE: STATION NUMBER, TRUNK NUMBER, BLADE NUMBER Outline of the Unit No. Unit No. 01 Unit No. 02 Unit No. 05 Unit No. 50 Unit No. 03 Unit No. 04 Remote Unit for Remote UNIT over IP Stand-alone system/ Main Unit for Remote UNIT over IP Continued on next page...
Page 160 CM10 COMMAND CODE TITLE: STATION NUMBER, TRUNK NUMBER, BLADE NUMBER Slot number and Circuit number The Slot number is the number assigned to the slot which accommodates the blade in a Line/Trunk chassis. The Circuit number is the number assigned to the circuit which accommodates the blade in a Line/ Trunk chassis.
Page 161 CM10 COMMAND CODE TITLE: STATION NUMBER, TRUNK NUMBER, BLADE NUMBER Setting method of Port number/Station number in Dual port mode When using Analog Port Adapter and PGD(2)-U10 ADP in Dual port mode NOTE 1, the Circuit numbers (17-32) of the DLC blade slot which accommodate Digital Multiline terminal/PGD(2)- U10 ADP are used for the virtual station.
Page 162 CM11 COMMAND CODE TITLE: VIRTUAL LINE NUMBER FUNCTION: This command is used to assign station numbers, Intercom numbers, Loop Line numbers and ICI/OPR Line numbers (for Multiline Terminal Attendant Position) to Virtual Lines assigned on Multiline Termi- nal. PRECAUTION: Virtual Line station numbers must be different from station numbers assigned by CM10. The Virtual Port No.
Page 163 CM11 COMMAND CODE TITLE: VIRTUAL LINE NUMBER ASSIGNMENT PROCEDURE: Virtual VIRTUAL LINE INTERCOM + 11 + + EXE NUMBER NUMBER PORT NUMBER (4 digits) (1-8 digits) (4 digits) DATA TABLE: VIRTUAL RELATED VIRTUAL LINE NUMBER PORT No. COMMAND 0000-0999 Station number (1-8 digits) CM20 X: 0-9, A (*), B (#) CM90...
Page 164 CM11 COMMAND CODE TITLE: VIRTUAL LINE NUMBER VIRTUAL RELATED VIRTUAL LINE NUMBER PORT No. COMMAND 0000-0999 B000 Dial Intercom number CM12 Y=03 CM56 Y=12 B900 BX YY CM90 B001 X : Intercom Code (0-9) YY : Dial Intercom Group number (00-24) NOTE 3 B901 B024...
Page 165 CM11 COMMAND CODE TITLE: VIRTUAL LINE NUMBER NOTE 1: Automatic Intercom numbers are assigned as shown below: AUTOMATIC AUTOMATIC AUTOMATIC INTERCOM INTERCOM INTERCOM GROUP No. (A) No. (B) A000 A100 A001 A101 A031 A131 NOTE 2: Manual Intercom numbers are assigned as shown below: MANUAL INTERCOM GROUP...
Page 166 CM12 COMMAND CODE TITLE: STATION CLASS-1 FUNCTION: The features for each station are determined by assigning Station Class-1 to each station number. PRECAUTION: When assigning Station Class-1 to Multiline Terminal by this command, enter “X-XXXXXXXX (My Line number)” of FX-FXXXXXXXX, which is assigned by CM10 Y=00, as the first data.
Page 167 CM12 COMMAND CODE TITLE: STATION CLASS-1 CM12 Y=24: 7 (A mode) CM12 Y=24: 0 (B mode) DT330/ LINE01 LINE05 LINE01 LINE05 DT730/ LINE02 LINE06 LINE02 LINE06 DT750 LINE03 LINE07 LINE03 LINE07 (8LD LINE04 LINE08 LINE04 LINE08 [DESI- LINE09 LINE13 LINE09 LINE13 less]) LINE10...
Page 168 CM12 COMMAND CODE TITLE: STATION CLASS-1 CM12 Y=24: 7 (A mode) CM12 Y=24: 0 (B mode) term LINE01 LINE02 LINE03 LINE04 DSS01 DSS02 LINE01 LINE02 LINE03 LINE04 LINE05 LINE06 Series i/ LINE05 LINE06 LINE07 LINE08 DSS03 DSS04 LINE07 LINE08 LINE09 LINE10 LINE11 LINE12 term LINE09 LINE10 LINE11 LINE12 DSS05 DSS06...
Page 169 CM12 COMMAND CODE TITLE: STATION CLASS-1 CM12 Y=24: 7 (A mode) CM12 Y=24: 0 (B mode) term LINE01 LINE02 LINE09 LINE10 Series i/ LINE03 LINE04 LINE11 LINE12 term Same as CM12 Y=24: 7 (A mode) LINE05 LINE06 LINE13 LINE14 (DTR- 16LD) LINE07 LINE08 LINE15 LINE16...
Page 170 CM12 COMMAND CODE TITLE: STATION CLASS-1 u: To assign –: Not assigned STATION NUMBER 00 01 02 03 04 05 07 11 12 13 16 19 20 22 23 24 25 Single line station number – – – – (Assigned by CM10 Y=00) Multiline Terminal My line –...
Page 171 CM12 COMMAND CODE TITLE: STATION CLASS-1 u: To assign –: Not assigned STATION NUMBER 26 29 30 31 32 33 34 35 36 37 38 39 43 44 45 46 47 Single line station number – – – – (Assigned by CM10 Y=00) Multiline Terminal My line –...
Page 172 CM12 COMMAND CODE TITLE: STATION CLASS-1 u: To assign –: Not assigned STATION NUMBER 48 50 61 62 63 64 65 66 67 68 69 70 71 90 92 93 Single line station number – – – – – – –...
Page 173 CM12 COMMAND CODE TITLE: STATION CLASS-1 ASSIGNMENT PROCEDURE: STATION Automatic/ Loop ICI/OPR DATA Manual/ Line Line No. (1-12 12YY ST + + DE (1-8 digits) Dial Intercom (4 digits) digits) No. (4 digits) (4 digits) DATA TABLE: : Default SETTING DATA RELATED COMMAND MEANING...
Page 174 CM12 COMMAND CODE TITLE: STATION CLASS-1 : Default SETTING DATA RELATED COMMAND MEANING DATA MEANING Kind of Telephone House Phone 0 CM51 Y=14 House Phone 1 House Phone 2 House Phone 3 FAX Call Station Group No. 0 CM51 Y=14 FAX Call Station Group No.
Page 175 CM12 COMMAND CODE TITLE: STATION CLASS-1 : Default SETTING DATA RELATED COMMAND MEANING DATA MEANING Service Restriction Class C Service Restriction Class C (00-15) CM15 NOTE: The features available in each Class are programmed in CM15. Kind of idle status of called Called station idle (No Charge) station on DID MFC call Called station control (Charge)
Page 176 CM12 COMMAND CODE TITLE: STATION CLASS-1 : Default SETTING DATA RELATED COMMAND MEANING DATA MEANING Combination of the main Main station number/Sub station number station and sub station for WCS Number Sharing XXXXXXXX NONE No data NOTE: Assign the data as follows. 1st data: Main station (Multiline Terminal My line) 2nd data: Sub station (PS) 1st data: Sub station (PS)
Page 177 CM12 COMMAND CODE TITLE: STATION CLASS-1 : Default SETTING DATA RELATED COMMAND MEANING DATA MEANING Kind of Multiline Terminal B mode CM94 A mode NOTE 1: The table below shows the combination of Line/Trunk/Feature Keys and One Touch Keys of the Multi- line Terminals.
Page 178 CM12 COMMAND CODE TITLE: STATION CLASS-1 : Default SETTING DATA RELATED COMMAND MEANING DATA MEANING Send indication data to To send indication data Line Key LCD of Multiline Data sending completed/Not sent Terminal (DESI-less) Request my line number to Available CM15 Y=210 the Multiline Terminal Not available...
Page 179 CM12 COMMAND CODE TITLE: STATION CLASS-1 : Default SETTING DATA RELATED COMMAND MEANING DATA MEANING Location number of IP Sta- Location number 00 CM67 tion for Local Connection Location number 63 NONE Location number 00 Group number for Group Group Call No. 00 CM13 Y=45 Call by Pilot Number Dial- CM57 Y=10-...
Page 180 CM12 COMMAND CODE TITLE: STATION CLASS-1 : Default SETTING DATA RELATED COMMAND MEANING DATA MEANING Location number of IP Sta- Location number 00 CM67 tion for Remote Connec- tion Location number 63 NONE Location number 00 Warning SST sending timer Depends on Timer A (CM41 Y=0>114) CM35 Y=247 for forced release...
Page 181 CM12 COMMAND CODE TITLE: STATION CLASS-1 : Default SETTING DATA RELATED COMMAND MEANING DATA MEANING Unit number to ISDN Unit number 01 Alternative Routing Unit for IP station/virtual PS sta- Unit number 50 tion number in Remote NONE No data Unit survival mode Kind of PGD(2)-U10 sta- Paging...
Page 182 CM12 COMMAND CODE TITLE: STATION CLASS-1 : Default SETTING DATA RELATED COMMAND MEANING DATA MEANING Assign the PGD(2)-U10 PGD(2)-U10 Station number station number to control the relay specified by an XXXX intervening Virtual Line XXXX Station NONE No data [8300R2] NOTE: This data is not available when setting the first data that is not a virtual station number.
Page 183 CM12 COMMAND CODE TITLE: STATION CLASS-1 : Default SETTING DATA RELATED COMMAND MEANING DATA MEANING MAC Address registration X..XXX MAC Address in Fixed Connection Mode (12 digits) Clear NONE No data NOTE 1: A maximum of 256 MAC Addresses can be registered in Fixed Connection Mode. NOTE 2: This command has to be registered after assigning CM15 Y=480 2nd data “1”...
Page 184 CM13 COMMAND CODE TITLE: STATION CLASS-2 FUNCTION: The features for each station are to be designated by assigning Station Class-2 for each station number. PRECAUTION: When assigning Station Class-2 to a Multiline Terminal by this command, enter “X-XXXXXXXX (My Line number)” of FX-FXXXXXXXX, which is assigned by CM10 Y=00, as the first data.
Page 185 CM13 COMMAND CODE TITLE: STATION CLASS-2 u: To assign –: Not assigned 34 35 37 39 40 41 45 46 49 51 52 54 55 56 57 58 59 60 61 63 64 66 67 68 STATION NUMBER Single line station number –...
Page 186 CM13 COMMAND CODE TITLE: STATION CLASS-2 : Default SETTING DATA MEANING DATA MEANING SMDR/Centralized Billing-CCIS for out- Not provided CM35 Y=014 going call To provide Analog data station (FAX, MODEM, Data station etc.) or ordinary station Ordinary station PRECAUTION (2) Send or not ringing signal to the single Not sent ringing signal CM12 Y=05...
Page 187 CM13 COMMAND CODE TITLE: STATION CLASS-2 : Default SETTING DATA MEANING DATA MEANING Automatic live recording To provide Not provided NOTE: When this feature is activated, be sure to set CM08>141, CM35 Y=22, and/or CM76 Y=13. CM08>141 CM35 Y=022 CM76 Y=13 In-Skin UMS or Digital Multiline Termi- In-Skin UMS Digital Multiline Terminal...
Page 188 CM13 COMMAND CODE TITLE: STATION CLASS-2 : Default SETTING DATA MEANING DATA MEANING WCS Roaming for Virtual Station of Vis- Available itor PS Not available [For PCS] [8300R2] Station number assigned by CM11 for Other office station BLF-CCIS Own office station Storage of the call record when answer- To store ing a station call...
Page 189 CM13 COMMAND CODE TITLE: STATION CLASS-2 : Default SETTING DATA MEANING DATA MEANING Provide Calling Number Display for the To provide stations of SLT/sub line of Multiline Ter- Not provided minal/Virtual line/Virtual station for PS that are accommodated to the Multiline Terminal multiline as a subline NOTE: When terminating the call to the stations of SLT/subline of Multiline Terminal/Virtual line/Virtual sta-...
Page 190 CM13 COMMAND CODE TITLE: STATION CLASS-2 : Default SETTING DATA MEANING DATA MEANING term Accommodation of D 70/PGD(2)-U10 To accommodate Not accommodated BLADE RESET NOTE 1: Set this data only for a Base Port of DLC blade. term NOTE 2: When the second data is set to “0”, D 70/PGD(2)-U10 ADP cannot be accommodated with term...
Page 191 CM15 COMMAND CODE TITLE: SERVICE RESTRICTION CLASS FUNCTION: Restriction of each service is to be set for each service restriction class assigned to the stations. There are four kinds of Service Restriction Class A/B/C and Charging Station. The services to be restricted by these Service Restriction Classes are different.
Page 192 CM15 COMMAND CODE TITLE: SERVICE RESTRICTION CLASS A DATA TABLE: Service Restriction Class A : Default SERVICE SETTING DATA REST. MEANING DATA MEANING CLASS (A) 000 Call Forwarding-All Calls Restricted Allow 001 Call Hold 002 Outgoing Trunk Queuing 003 Call Back 005 Executive Right of Way (Executive Override) Calling side 006 System Speed Dialing...
Page 193 CM15 COMMAND CODE TITLE: SERVICE RESTRICTION CLASS A Service Restriction Class A : Default SERVICE SETTING DATA REST. MEANING DATA MEANING CLASS (A) 021 Automatic Wake Up set from guest or administrative station Restricted (Different wake up time is set to multiple stations) Allow 022 Trunk-to-Trunk Transfer 024 Message Waiting Lamp set/reset from station...
Page 194 CM15 COMMAND CODE TITLE: SERVICE RESTRICTION CLASS A Service Restriction Class A : Default SERVICE SETTING DATA REST. MEANING DATA MEANING CLASS (A) 041 Voice Message Waiting-System/Individual Restricted Set/Cancel/Retrieve Allow 042 Voice Message Waiting-System Recording 043 Call Waiting Set-Calling Side 044 Call Waiting Answer-Called Side 046 Call Back-Multiple Assignment 047 Message Reminder Setting Side...
Page 195 CM15 COMMAND CODE TITLE: SERVICE RESTRICTION CLASS A Service Restriction Class A : Default SERVICE SETTING DATA REST. MEANING DATA MEANING CLASS (A) 115 PS Call Forwarding-Not Available Restricted Allow 116 Voice Guide Restricted Validity of dial tone sending Allow 117 WCS Roaming Allow [For PCS] [8300R2]...
Page 196 CM15 COMMAND CODE TITLE: SERVICE RESTRICTION CLASS A Service Restriction Class A : Default SERVICE SETTING DATA REST. MEANING DATA MEANING CLASS (A) 131 Set Relocation Allow Setting Side NOTE 1 NOTE 2 Restricted 132 Being moved and changed by Set Relocation Allow Set Side NOTE 1 NOTE 2...
Page 197 CM15 COMMAND CODE TITLE: SERVICE RESTRICTION CLASS A Service Restriction Class A : Default SERVICE SETTING DATA REST. MEANING DATA MEANING CLASS (A) 140 Pad Lock Set/Reset from station Allow Restricted 141 Station Authorization Code Set/Change Restricted Allow 143 IP Station Logout operation Allow Restricted 146 Sending Switch Hook Flash for Adjunct Analog System...
Page 198 CM15 COMMAND CODE TITLE: SERVICE RESTRICTION CLASS A Service Restriction Class A : Default SERVICE SETTING DATA REST. MEANING DATA MEANING CLASS (A) 207 Indication when a station is set to the Line Key of Multiline Station Number Terminal (DESI-less) Station Name 210 Display my line number on the Multiline Terminal Restricted...
Page 199 CM15 COMMAND CODE TITLE: SERVICE RESTRICTION CLASS A Service Restriction Class A : Default SERVICE SETTING DATA REST. MEANING DATA MEANING CLASS (A) 400 Displaying pattern of Caller ID on the LCD of Multiline Ter- To display calling minal before answering or after answering a trunk call number on upper line of LCD, calling name on middle line of LCD...
Page 200 CM15 COMMAND CODE TITLE: SERVICE RESTRICTION CLASS B Service Restriction Class B : Default SERVICE SETTING DATA REST. MEANING DATA MEANING CLASS (B) 053 TAS Service Restricted Allow 055 Individual Trunk Access from Station 056 Change of mode for CAT 059 Starting up OAI MSF from PB telephone/Multiline Terminal by using access code 060 Day Night Mode Change by Station Dialing...
Page 201 CM15 COMMAND CODE TITLE: SERVICE RESTRICTION CLASS B Service Restriction Class B : Default SERVICE SETTING DATA REST. MEANING DATA MEANING CLASS (B) 072 Automatic Hold Allow Restricted 073 Attendant Terminal ICI/OPE Key ICI/OPE Key CM15 Y=071 Regular station 075 Maid Status Restricted Allow 076 Collect Call Called Side...
Page 202 CM15 COMMAND CODE TITLE: SERVICE RESTRICTION CLASS C Service Restriction Class C : Default SERVICE SETTING DATA REST. MEANING DATA MEANING CLASS (C) 081 One hit ringing for Call Forwarding-All Calls Restricted Allow 082 Ringing Line Pick up Allow Restricted Multiline Terminal Ringer Tone Pattern See below The ringer tone pattern is assigned by the combination of...
Page 203 CM15 COMMAND CODE TITLE: SERVICE RESTRICTION CLASS C Service Restriction Class C : Default SERVICE SETTING DATA REST. MEANING DATA MEANING CLASS (C) Switch Hook Flash during internal call See below Result of a Switch Hook Flash during a station-to-station call is specified by the combination of CM15 Y=088, 089.
Page 204 CM15 COMMAND CODE TITLE: SERVICE RESTRICTION CLASS C Service Restriction Class C : Default SERVICE SETTING DATA REST. MEANING DATA MEANING CLASS (C) 093 Multiline Terminal Ringer Tone Pattern See below Multiline Terminal ringer tone pattern is assigned by the fol- lowing combination of CM15 Y=083, 084, and 093.
Page 205 CM15 COMMAND CODE TITLE: SERVICE RESTRICTION CLASS C Service Restriction Class C : Default SERVICE SETTING DATA REST. MEANING DATA MEANING CLASS (C) 099 Voice Call Mike Off Called Side Available Not available 182 Non private extension Available Not available 186 Voice Mail Live Monitoring Available Not available...
Page 206 CM15 COMMAND CODE TITLE: SERVICE RESTRICTION CLASS C Service Restriction Class C : Default SERVICE SETTING DATA REST. MEANING DATA MEANING CLASS (C) 481 Call Forwarding-Logout (IP Station)/Call Forwarding-PS Out Restricted of Cell (Zone) Allow (Send ROT when no destination is set) Allow (Send RBT when no destination is...
Page 207 CM15 COMMAND CODE TITLE: SERVICE RESTRICTION CLASS C Service Restriction Class C : Default SERVICE SETTING DATA REST. MEANING DATA MEANING CLASS (C) 484 Priority for Call Forwarding-All Calls of Mobility Access call See below PRIORITY 2ND DATA=0 2ND DATA=3 Restriction of Inter-tenant Connection Restriction of Inter-tenant Connection HIGH...
Page 208 CM15 COMMAND CODE TITLE: SERVICE RESTRICTION CLASS C Service Restriction Class C : Default SERVICE SETTING DATA REST. MEANING DATA MEANING CLASS (C) 485 Time that LCD backlight for DT300/DT700 Series Always off [8300R2] Always on 5 seconds 10 seconds 15 seconds 30 seconds 60 seconds...
Page 209 CM15 COMMAND CODE TITLE: CHARGING STATION CLASS Charging Station Class : Default CHARGING SETTING DATA STATION MEANING DATA MEANING CLASS 390 Send detail information of Immediate Printout Call Record for Allow the PMS Restricted 391 Accumulate the call charge Allow Restricted 393 The operation set by CM4B Y=00 is executed simultaneously Allow...
Page 210 CM16 COMMAND CODE TITLE: CALL PICKUP GROUP/GROUP DIVERSION GROUP FUNCTION: This command is used to allocate stations to each Call Pickup group and Group Diversion group. PRECAUTION: The maximum number of stations which can be assigned to a Call Pickup group is 60. There is no limitation to the number of Call Pickup groups.
Page 211 CM16 COMMAND CODE TITLE: CALL PICKUP GROUP/GROUP DIVERSION GROUP DATA TABLE: : Default STATION NUMBER (A) SETTING DATA MEANING DATA MEANING DATA MEANING Next station number Station number (A) Station number (B) in Call Pickup Group XXXXXXXX XXXXXXXX NONE No data When assigning station numbers to a Call Pickup group, only two station numbers can be assigned per operation.
Page 212 CM16 COMMAND CODE TITLE: CALL PICKUP GROUP/GROUP DIVERSION GROUP : Default STATION NUMBER (A) SETTING DATA MEANING DATA MEANING DATA MEANING Pilot station in Call Station number in Call Pilot station Pickup group Pickup-Group Member station NOTE XXXXXXXX NOTE: Only one station can be assigned as the Pilot station of a Call Pickup group. 3-163 NWA-033623-001 Rev.3.0 91ch3002.fm...
Page 213 CM17 COMMAND CODE TITLE: ACD/UCD GROUP FUNCTION: This command is used to define ACD (Automatic Call Distribution)/UCD (Uniform Call Distribution) groups. PRECAUTION: A maximum of 16 ACD/UCD groups can be assigned per system. A maximum number of 60 stations can be assigned to a ACD/UCD group. Prior to changing or deleting the station number within a ACD/UCD group, in CM17 Y=0, it is necessary to change the data for CM17 Y=1-7 to the default.
Page 214 CM17 COMMAND CODE TITLE: ACD/UCD GROUP : Default STATION NUMBER (A) SETTING DATA RELATED COMMAND MEANING DATA MEANING DATA MEANING Pilot station in Station number to Member station CM44 Y=00: ACD/UCD group be assigned as Pilot Pilot station 14XX XXXXXXXX CM49 Y=00 Pilot station and Station number to...
Page 215 CM17 COMMAND CODE TITLE: ACD/UCD GROUP : Default STATION NUMBER (A) SETTING DATA RELATED COMMAND MEANING DATA MEANING DATA MEANING ACD/UCD Delay Pilot station num- To send periodically CM41 Announcement ber of ACD/UCD To send only once Y=0>16/47/67 Service XXXXXXXX group CM49 Y=00 CM51 Y=17...
Page 216 CM18 COMMAND CODE TITLE: STATION HUNTING GROUP FUNCTION: This command is used to assign stations to a Station Hunting group. There are three hunt types; Station Hunting-Terminal, Station Hunting-Circular and Station Hunting-Secretarial. PRECAUTION: When a Station Hunting group requires a secretary station, it is necessary to assign CM18 Y=2. The maximum number of stations which can be assigned to a Station Hunting group is 60.
Page 217 CM18 COMMAND CODE TITLE: STATION HUNTING GROUP DATA TABLE: Station Hunting-Terminal : Default STATION NUMBER (A) SETTING DATA MEANING DATA MEANING DATA MEANING Next station number in Station number (A) Station number (B) Station Hunting group XXXXXXXX XXXXXXXX NONE No data When assigning station numbers to a Station Hunting group, only two station numbers can be assigned per operation.
Page 218 CM18 COMMAND CODE TITLE: STATION HUNTING GROUP : Default STATION NUMBER (A) SETTING DATA MEANING DATA MEANING DATA MEANING Secretary station Secretary station number Secretary station serial numbers Secretary station should XXXXXXXX be Pilot station. Not assigned Operation: The correspondence between Serial numbers and Secretary station numbers is set by CM19.
Page 219 CM18 COMMAND CODE TITLE: STATION HUNTING GROUP Station Hunting-Circular : Default STATION NUMBER (A) SETTING DATA MEANING DATA MEANING DATA MEANING Next station number in Station number (A) Station number (B) Station Hunting group XXXXXXXX XXXXXXXX NONE No data Example: When you define a Station Hunting-Circular group which consists of station numbers 310-312, the following three operations are required: Station No.
Page 220 CM18 COMMAND CODE TITLE: STATION HUNTING GROUP : Default STATION NUMBER (A) SETTING DATA MEANING DATA MEANING DATA MEANING Secretary station: Secretary station number Secretary station serial numbers Operation: XXXXXXXX Not assigned A B C D Secretary The correspondence between Serial numbers and Secretary station numbers is set by CM19.
Page 221 CM18 COMMAND CODE TITLE: STATION HUNTING GROUP Station Hunting-Secretarial : Default STATION NUMBER (A) SETTING DATA MEANING DATA MEANING DATA MEANING Next station number in Station number (A) Station number (B) Station Hunting group XXXXXXXX XXXXXXXX NONE No data Example: When you define Station Hunting-Secretarial group which consists of station numbers 320-323, the following four operations are required: Station No.
Page 222 CM18 COMMAND CODE TITLE: STATION HUNTING GROUP : Default STATION NUMBER (A) SETTING DATA MEANING DATA MEANING DATA MEANING Secretary station Secretary station number Secretary station serial numbers Operation: XXXXXXXX Not assigned The correspondence between Serial numbers and Secretary station numbers is set by Secretary CM19.
Page 223 CM19 COMMAND CODE TITLE: SECRETARY/GROUP DIVERSION STATION NUMBER FUNCTION: This command is used to assign Secretary station numbers. And also, to assign transferred stations for Group Diversion. PRECAUTION: None ASSIGNMENT PROCEDURE: SECRETARY STATION DATA GROUP DIVERSION ST + SERIAL NUMBER (1-8 digits) GROUP (00-30) (00-30)
Page 224 CM19 COMMAND CODE TITLE: SECRETARY/GROUP DIVERSION STATION NUMBER : Default SECRETARY SETTING DATA STATION SERIAL MEANING DATA MEANING NUMBER Transferred station of Call 00: Group Diversion Station number transferred. Forwarding-No Answer for each Group group 00 Data “E000” (DESKCON) Diversion group XXXXXXXX is not provided.
Page 225 CM1B COMMAND CODE TITLE: ISDN TELEPHONE MULTIPOINT STATION NUMBER FUNCTION: This command is used for an ISDN Telephone Multipoint station number. PRECAUTION: None ASSIGNMENT PROCEDURE: ISDN LINE ISDN DATA + 1B + STATION No. MULTIPOINT No. (1-8 digits) (1-8 digits) (0-7) DATA TABLE: 1ST DATA...
Page 226 CM1D COMMAND CODE TITLE: PS-ID ASSIGNMENT/PS OPERATION DATA DOWNLOAD FUNCTION: This command is used to assign the PS-ID, to download the PS operation data. PRECAUTION: When a PS is set up initially, set the PS in Data Download Mode by applying power to the PS while pressing the SEND key, and then execute the CM1D Y=20 in Calling Area No.
Page 227 CM1D COMMAND CODE TITLE: PS-ID ASSIGNMENT/PS OPERATION DATA DOWNLOAD : Default SETTING DATA RELATED PS STATION No. COMMAND MEANING DATA MEANING Terminal type of PS X-XXXXXXXX Multiline Terminal PS II CM10 Y=04 [For PCS] (Primary/Subline Type with PS software ver- PS Station No.) sion 7.02 or later NOTE 1:...
Page 228 CM1D COMMAND CODE TITLE: PS-ID ASSIGNMENT/PS OPERATION DATA DOWNLOAD : Default SETTING DATA RELATED PS STATION No. COMMAND MEANING DATA MEANING A combination of PS station X-XXXXXXXX XX...XX PS station No. CM10 Y=04 number that converted from (Primary Subline (assigned by CM1C from NEAX 2000 IPS and PS Station No.) NEAX 2000 IPS)
Page 229 CM20 COMMAND CODE TITLE: NUMBERING PLAN/SINGLE DIGIT FEATURE ACCESS CODE (PROGRAMMABLE) FUNCTION: Trunk routes and features are assigned by developing access codes. For Route Advance and Tenant development, see CM22 and CM23. The following figure shows the relationship between commands: For each access code Numbering Plan Route Advance Block...
Page 230 CM20 COMMAND CODE TITLE: NUMBERING PLAN/SINGLE DIGIT FEATURE ACCESS CODE (PROGRAMMABLE) Name Display Registration From Multiline Terminal is as follows. • You can configure the station number from the Multiline Terminal to which the station number belongs. • Register the characters from PCPro/CAT to SLT, Multiline Terminal without LCD and Trunk. •...
Page 231 CM20 COMMAND CODE TITLE: NUMBERING PLAN/SINGLE DIGIT FEATURE ACCESS CODE (PROGRAMMABLE) Character Table NUMBER OF TIMES Table 0-1 ASSIGNMENT PROCEDURE: ACCESS CODE DATA + DE (1-4 digits) (1-4 digits) 3-182 NWA-033623-001 Rev.3.0 91ch3003.fm...
Page 232 CM20 COMMAND CODE TITLE: NUMBERING PLAN/SINGLE DIGIT FEATURE ACCESS CODE (PROGRAMMABLE) DATA TABLE: Y=0-3 ACCESS CODE RELATED COMMAND MEANING Numbering Plan Group 0 X: 0-9, A (*), B (#) CM29 Numbering Plan Group 1 Numbering Plan Group 2 XXXX Numbering Plan Group 3 Continued on next page 3-183 NWA-033623-001 Rev.3.0...
Page 233 CM20 COMMAND CODE TITLE: NUMBERING PLAN/SINGLE DIGIT FEATURE ACCESS CODE (PROGRAMMABLE) SETTING DATA: A004-A097 SETTING DATA RELATED REMARKS COMMAND DATA MEANING A004 Outgoing Trunk Queueing/Call Back/Call When Outgoing Trunk Queueing, Call CM15 Y=002, 003, Completion to Busy Subscriber (CCBS) Set Back and Completion of Calls to Busy 025, 157, 158 [For EU]...
Page 234 CM20 COMMAND CODE TITLE: NUMBERING PLAN/SINGLE DIGIT FEATURE ACCESS CODE (PROGRAMMABLE) SETTING DATA RELATED REMARKS COMMAND DATA MEANING A027 Wake Up Call Set from Predetermined Station CM15 Y=020 (Single Wake Up time operation) A028 Wake Up Call Set from Predetermined Station CM15 Y=021 (Multiple Wake Up time operation) A029...
Page 235 CM20 COMMAND CODE TITLE: NUMBERING PLAN/SINGLE DIGIT FEATURE ACCESS CODE (PROGRAMMABLE) SETTING DATA RELATED REMARKS COMMAND DATA MEANING A047 TAS Answer A CM15 Y=053 CM53 A048 TAS Answer B A049 TAS Answer C A050 TAS Answer D A051 TAS Answer E A058 Trunk Hold A059...
Page 236 CM20 COMMAND CODE TITLE: NUMBERING PLAN/SINGLE DIGIT FEATURE ACCESS CODE (PROGRAMMABLE) SETTING DATA RELATED REMARKS COMMAND DATA MEANING A078 Paging Answer Zone 8 CM30 Y=28 CM44 A079 Paging Answer Zone 9 CM15 Y=008 CM08>157 A080 Speaker/Radio Paging Cancel CM41 Y=0>20 (Delay Operation) A081 Individual Trunk Access...
Page 237 CM20 COMMAND CODE TITLE: NUMBERING PLAN/SINGLE DIGIT FEATURE ACCESS CODE (PROGRAMMABLE) SETTING DATA RELATED REMARKS COMMAND DATA MEANING A095 Individual Attendant Access/Inter Position CM90 Transfer [8300R2] A097 Direct Data Entry CM90 Continued on next page 3-188 NWA-033623-001 Rev.3.0 91ch3003.fm NOVEMBER/12/2008...
Page 238 CM20 COMMAND CODE TITLE: NUMBERING PLAN/SINGLE DIGIT FEATURE ACCESS CODE (PROGRAMMABLE) SETTING DATA: 800-828 SETTING DATA RELATED REMARKS COMMAND DATA MEANING Operator Call CM90 [8300R2] 1 digit Station 2 digits Station 3 digits Station 4 digits Station 5 digits Station For the following features, do not assign 5 or more digits station number.
Page 239 CM20 COMMAND CODE TITLE: NUMBERING PLAN/SINGLE DIGIT FEATURE ACCESS CODE (PROGRAMMABLE) SETTING DATA: A100-A199 SETTING DATA RELATED REMARKS COMMAND DATA MEANING A100 Voice Response System Access Record CM10 CM15 Y=033 A101 Voice Response System Access Replay A102 Voice Response System Access Delete A103 Announcement Service Record CM10...
Page 240 CM20 COMMAND CODE TITLE: NUMBERING PLAN/SINGLE DIGIT FEATURE ACCESS CODE (PROGRAMMABLE) SETTING DATA RELATED REMARKS COMMAND DATA MEANING A126 LCR Group 0 CM8A Y=A000 A127 LCR Group 1 A128 LCR Group 2 A129 LCR Group 3 Assign A129 only when the LCR Group access code is included in the area code table in CM8A (Closed Numbering).
Page 241 CM20 COMMAND CODE TITLE: NUMBERING PLAN/SINGLE DIGIT FEATURE ACCESS CODE (PROGRAMMABLE) SETTING DATA RELATED REMARKS COMMAND DATA MEANING A146 Message Waiting/Message Reminder Search CM15 Y=047, 048 A147 Message Waiting/Message Reminder Retrieve CM13>03 A148 Message Reminder Set CM90 A149 Message Reminder Cancel A150 System Speed Dialing Origination For 1000 memories...
Page 242 CM20 COMMAND CODE TITLE: NUMBERING PLAN/SINGLE DIGIT FEATURE ACCESS CODE (PROGRAMMABLE) SETTING DATA RELATED REMARKS COMMAND DATA MEANING A181 Split Call Forwarding-All Calls Cancel A182 Split Call Forwarding-Busy Line/-No Answer A183 Split Call Forwarding-Busy Line/-No Answer Cancel A188 Whisper Page A189 Call Forwarding-Not Available Set A190...
Page 243 CM20 COMMAND CODE TITLE: NUMBERING PLAN/SINGLE DIGIT FEATURE ACCESS CODE (PROGRAMMABLE) SETTING DATA: A230-A258 SETTING DATA RELATED REMARKS COMMAND DATA MEANING A230 Station Class change with Station Authorization CM42>73 Code A231 Station Authorization Code/Password Change CM42>73 A232 Pad Lock Set by Station Authorization Code A233 Pad Lock Reset by Station Authorization Code A234...
Page 244 CM20 COMMAND CODE TITLE: NUMBERING PLAN/SINGLE DIGIT FEATURE ACCESS CODE (PROGRAMMABLE) SETTING DATA: 100-515 SETTING DATA RELATED REMARKS COMMAND DATA MEANING Trunk Route 00 Data is to be assigned for Trunk CM30 Routes corresponding to the access Trunk Route 63 codes for outgoing trunk calls (COT, LDT, ODT, etc.).
Page 245 CM20 COMMAND CODE TITLE: NUMBERING PLAN/SINGLE DIGIT FEATURE ACCESS CODE (PROGRAMMABLE) DATA TABLE: Y=4, 5 : Default SETTING DATA RELATED ACCESS CODE COMMAND DATA MEANING MEANING Single Digit X: 0-9, A (*), B (#) Call Back/Trunk Queuing- CM08>570 Feature Access Outgoing Code for BT Executive Override...
Page 246 CM21 COMMAND CODE TITLE: SINGLE DIGIT ACCESS CODE FUNCTION: This command sets a single digit code to be recognized under timing start condition. PRECAUTION: None ASSIGNMENT PROCEDURE: ACCESS DATA + DE CODE (3/4 digits) (1 digit) DATA TABLE: SETTING DATA ACCESS CODE MEANING DATA...
Page 247 CM22 COMMAND CODE TITLE: ROUTE ADVANCE FUNCTION: This command is used to assign alternative trunk routes to each Route Advance Block. PRECAUTION: A maximum of seven consecutive priorities can be assigned. ASSIGNMENT PROCEDURE: PRIORITY DATA + DE 22YY ORDER (3 digits) (1 digit) DATA TABLE: SETTING DATA...
Page 248 CM23 COMMAND CODE TITLE: TENANT DEVELOPMENT FUNCTION: Trunk routes and services are assigned by developing access codes for each tenant. For further development, use CM22 Route Advance. PRECAUTION: None ASSIGNMENT PROCEDURE: TENANT DATA + DE 23YY NUMBER (3/4 digits) (2 digits) DATA TABLE: SETTING DATA RELATED...
Page 249 CM25 COMMAND CODE TITLE: KIND OF SPECIAL TERMINAL DEVELOPMENT FUNCTION: For each access code assigned to a special terminal block, a trunk route can be assigned based on which type of special terminal (ordinary station or FAX station) is placing the call. For special terminal assign- ments requiring development of route advance data for trunk route assignment, route advance develop- ment and the corresponding trunk routes are assigned using CM22.
Page 250 CM29 COMMAND CODE TITLE: NUMBERING PLAN TENANT GROUP FUNCTION: When each tenant has its own numbering plan in a multiple-tenant system, all the tenants are divided into four groups. Numbering Plan Group data is then assigned on a tenant basis. PRECAUTION: If the data is not assigned (“NONE”), then Numbering Plan Group 0 is used for all tenants.
Page 251 CM2A COMMAND CODE TITLE: ID CODE ASSIGNMENT WITH CPU/DEVELOPMENT BLOCK NUMBER ASSIGNMENT FOR EACH CALLING PARTY NUMBER FUNCTION: This command assigns ID codes used for the Authorization Code/Forced Account Code/Remote Access to System (DISA) features with CPU and Development Block number for each calling party number. PRECAUTION: These ID codes are effective when CM08>216/217 are set to “0”.
Page 252 CM2A COMMAND CODE TITLE: ID CODE ASSIGNMENT WITH CPU/DEVELOPMENT BLOCK NUMBER ASSIGNMENT FOR EACH CALLING PARTY NUMBER : Default 1ST DATA 2ND DATA MEANING DATA MEANING DATA MEANING Valid range of ID Code 0000-2999 ID Code Pattern number Authorization Code, Forced Account Code, and Remote Access to System (DISA) Authorization Code, Forced...
Page 253 CM2A COMMAND CODE TITLE: ID CODE ASSIGNMENT WITH CPU/DEVELOPMENT BLOCK NUMBER ASSIGNMENT FOR EACH CALLING PARTY NUMBER : Default 1ST DATA 2ND DATA MEANING DATA MEANING DATA MEANING Service Restriction 0000-2999 ID Code Pattern Service Restriction Class C Class C number 00-15 NOTE:...
Page 254 CM2A COMMAND CODE TITLE: ID CODE ASSIGNMENT WITH CPU/DEVELOPMENT BLOCK NUMBER ASSIGNMENT FOR EACH CALLING PARTY NUMBER : Default 1ST DATA 2ND DATA MEANING DATA MEANING DATA MEANING ID Code Development Authorization Code ID Code Development number Number 00-09 Forced Account Code NOTE: CM2A (Related Command: CM2A...
Page 255: Assignment/Station Digest Authentication Password Assignment
CM2B COMMAND CODE TITLE: AUTHORIZATION CODE PER STATION/IP STATION PASSWORD ASSIGNMENT/STATION DIGEST AUTHENTICATION PASSWORD ASSIGNMENT FUNCTION: This command is used to set up the Authorization Code per station for PAD Lock feature. Also used to set up the password for the ID registration of the IP Station and Station Digest Authentication. PRECAUTION: None ASSIGNMENT PROCEDURE:...
Page 256 CM2B COMMAND CODE TITLE: AUTHORIZATION CODE PER STATION/IP STATION PASSWORD ASSIGNMENT/STATION DIGEST AUTHENTICATION PASSWORD ASSIGNMENT : Default 1ST DATA 2ND DATA RELATED COMMAND MEANING DATA MEANING DATA MEANING Trunk Restric- Station number Unrestricted (RCA) CM12 Y=02 tion Class Non-Restricted 1 (RCB) CM15 Y=031 XXXXXXXX Non-Restricted 2 (RCC)
Page 257 CM30 COMMAND CODE TITLE: TRUNK DATA FUNCTION: This command is used to assign characteristics to trunk lines and IPT (P2P CCIS) lines which have been defined by CM10. PRECAUTION: Do not assign Trunk number 511 for CCIS/IP. ASSIGNMENT PROCEDURE: TRUNK DATA 30YY NUMBER...
Page 258 CM30 COMMAND CODE TITLE: TRUNK DATA : Default SETTING DATA RELATED COMMAND MEANING DATA MEANING Terminating system in Day Mode Trunk Line (Direct) Appearance CM30 Y=18 for incoming C.O. calls Trunk Line (Direct) Appearance + TAS NOTE 1: When data 02, 03, 11 Direct-In Termination CM30 Y=04 or 12 is assigned, set...
Page 259 CM30 COMMAND CODE TITLE: TRUNK DATA : Default SETTING DATA RELATED COMMAND MEANING DATA MEANING Direct-In Termination in Day Station number for Direct-In Termina- CM10, CM11 Mode tion in Day Mode XXXXXXXX Abbreviated code of System Speed CM71>67 Dialing for DIT-Outside (XX: 00-31) CM35 Y=040 EBXXX Voice Response System number (XXX:...
Page 260 CM30 COMMAND CODE TITLE: TRUNK DATA : Default SETTING DATA RELATED COMMAND MEANING DATA MEANING CIC (Circuit Identification Code) CIC000 used for ISDN-Primary Rate Interface voice channels NOTE CIC029 NONE No data Restriction of outgoing connec- Restricted CM60 tion during Night Mode Allow NOTE: Assign CIC to voice channels only.
Page 261 CM30 COMMAND CODE TITLE: TRUNK DATA : Default SETTING DATA RELATED COMMAND MEANING DATA MEANING Trunk group number Identification of Trunk Group Busy CM44 Y=00: 11XX NOTE: Paging trunks cannot be Lamps on an external display device assigned to the Trunk Identification of Trunk Group Busy CM90 Y=00: Group Busy Lamp.
Page 262 CM30 COMMAND CODE TITLE: TRUNK DATA : Default SETTING DATA RELATED COMMAND MEANING DATA MEANING Trunk number XXXX Trunk ID code NOTE ISDN subscriber number XXXX ISDN subscriber number NOTE CM30 Y=34 CM50 Y=05 NOTE: For Individual Trunk Access, assign the trunk ID code/ISDN subscriber number by CM30 Y=19.
Page 263 CM30 COMMAND CODE TITLE: TRUNK DATA : Default SETTING DATA RELATED COMMAND MEANING DATA MEANING Handling of busy/not available C.O. line release CM41 Y=0>34 Automated Attendant/Remote Forward to TAS indicator CM30 Y=04, 05 Access to System Forward to Attendant Console CM49 Y=02 (DISA) destination in Day Mode [8300R2]...
Page 264 CM30 COMMAND CODE TITLE: TRUNK DATA : Default SETTING DATA RELATED COMMAND MEANING DATA MEANING Automated Attendant C.O. line release CM30 Y=30, 31 Handling of all PBR busy when Forward to TAS indicator 2nd announcement and DT are Forward to Attendant Console connected.
Page 265 CM30 COMMAND CODE TITLE: TRUNK DATA : Default SETTING DATA RELATED COMMAND MEANING DATA MEANING Terminating System in Mode A Trunk Line (Direct) Appearance CM30 Y=18 for incoming C.O. calls Trunk Line (Direct) Appearance + TAS NOTE 1: When data 02, 03, 11 Direct-In Termination CM30 Y=05 or 12 is assigned, set...
Page 266 CM30 COMMAND CODE TITLE: TRUNK DATA : Default SETTING DATA RELATED COMMAND MEANING DATA MEANING Direct-In Termination in Mode B Station number for Direct-In Termina- CM10, CM11 tion in Mode B: Night Connection- CM08>179 XXXXXXXX Fixed Abbreviated code of System Speed CM71>66 Dialing for DIT-Outside (XX: 00-31) CM35 Y=040...
Page 267 CM31 COMMAND CODE TITLE: MF-ANI TRUNK DATA FUNCTION: This command is used to assign the attribute data to MF-ANI trunk lines. PRECAUTION: None ASSIGNMENT PROCEDURE: 1ST DATA 2ND DATA + DE (1-2 digits) (1-2 digits) DATA TABLE: : Default 1ST DATA 2ND DATA DATA MEANING...
Page 268 CM31 COMMAND CODE TITLE: MF-ANI TRUNK DATA : Default 1ST DATA 2ND DATA DATA MEANING DATA MEANING Number of received digits of called 1 digit number from PSTN/T1 network 31 digits RESET NONE No data Signal pattern received from T1 network Called number + ANI [North America Only] Called number...
Page 269 CM31 COMMAND CODE TITLE: MF-ANI TRUNK DATA : Default 1ST DATA 2ND DATA DATA MEANING DATA MEANING Sending of ACK-WINK signal to DTI on To send receiving DP signal Not sent [North America Only] NOTE: When the signal pattern from T-1 network is FGD format, assign the data to “1”.
Page 270 CM31 COMMAND CODE TITLE: MF-ANI TRUNK DATA : Default 1ST DATA 2ND DATA DATA MEANING DATA MEANING Sending duration of Backward signal 0 ms. [Not used in Australia/ 50 ms. North America] Increment unit: 50 ms. 600 ms. RESET NOTE NONE NOTE: When this data is not assigned,...
Page 271 CM35 COMMAND CODE TITLE: TRUNK ROUTE DATA FUNCTION: This command is used to assign trunk route characteristics. A trunk route is a group of trunks with com- mon characteristics used for a common purpose. PRECAUTION: When assigning a Tie line, the data in CM35 Y=009 (Incoming connection signaling) should be similar to that of CM35 Y=020 (Sender starting condition).
Page 272 CM35 COMMAND CODE TITLE: TRUNK ROUTE DATA Voice quality improvement of SV8300 When the voice interruption or the echo occurs during calling via SV8300, you need to improve voice quality by setting PAD control etc. Control of Intra-office connection PAD (SLT/Mutiline Terminal) (1) CM13 Y=09 (Intra-office connection PAD) 1st data =X-XXXXXXXX (Station number) 2nd data=1...
Page 273 CM35 COMMAND CODE TITLE: TRUNK ROUTE DATA (2) CM35 Y=290 (Setting of PAD data from a station to a trunk) 1st data =00-63 (Trunk route number) 2nd data=13 (3 dB loss) (3) CM35 Y=291 (CODEC Filter Type) BLADE RESET 1st data=00-63 (Trunk route number) 2nd data: see below 2ND DATA RECITAL...
Page 274 CM35 COMMAND CODE TITLE: TRUNK ROUTE DATA • PAD data between locations (for IPT [P2P CCIS]) (1) CM67 Y=02 (PAD data between locations) 1st data=XX ZZ (Trunk route number) XX=00-63 (Location Number) ZZ =00-63 (Location Number) 2nd data=0004 (0 dB loss [send]/8 dB loss [receive]) NOTE 4: This command needs to be set for each location number.
Page 275 CM35 COMMAND CODE TITLE: TRUNK ROUTE DATA DATA TABLE: Y=000-098 : Default SETTING DATA RELATED COMMAND MEANING DATA MEANING Kind of Trunk Route DDD (C.O., DID, ISDN, SIP) trunk [North America Only] FX trunk RESET WATS trunk [North America Only] BLADE RESET CCSA trunk [North America Only]...
Page 276 CM35 COMMAND CODE TITLE: TRUNK ROUTE DATA : Default SETTING DATA RELATED COMMAND MEANING DATA MEANING Answer signal from distant Answer signal arrives (12 kHz, 50 Hz Metering CM41 Y=0 office for outgoing connec- signal) (C.O. line) tion Battery Reversal (C.O. line) Answer signal arrives (Tie line/ISDN/CCIS/SIP) Answer signal does not arrive...
Page 277 CM35 COMMAND CODE TITLE: TRUNK ROUTE DATA : Default SETTING DATA RELATED COMMAND MEANING DATA MEANING Toll Restriction To provide CM81, CM8A Not provided CM85 CM35 Y=076 Number of digits to be 1 digit CM76 received on DID for Devel- 2 digits CM35 Y=018 opment Table 0...
Page 278 CM35 COMMAND CODE TITLE: TRUNK ROUTE DATA : Default SETTING DATA RELATED COMMAND MEANING DATA MEANING Kind of call termination C.O. Incoming Call 0 (Standard “LDN” key) CM90 indicator key/lamp on Atten- CM50 dant Console C.O. Incoming Call 7 FX Incoming Call 0 (Standard “FX” key) [North America Only] Call termination indicator lamps further categorized by...
Page 279 CM35 COMMAND CODE TITLE: TRUNK ROUTE DATA : Default SETTING DATA RELATED COMMAND MEANING DATA MEANING Digit addition and deletion “0” add CM50 Y=00 at the time of a Tie line “1” add incoming call: “2” add On an incoming call from a “3”...
Page 280 CM35 COMMAND CODE TITLE: TRUNK ROUTE DATA : Default SETTING DATA RELATED COMMAND MEANING DATA MEANING Sender prepause timing 0 second CM08>193, 194, 0.5 seconds 1.0 second 1.5 seconds 2.0 seconds 2.5 seconds 4.0 seconds 5.0 seconds 6.0 seconds 7.0 seconds 8.0 seconds 9.0 seconds 10.0 seconds...
Page 281 CM35 COMMAND CODE TITLE: TRUNK ROUTE DATA : Default SETTING DATA RELATED COMMAND MEANING DATA MEANING DTMF Inter-digital pause 32 ms. 64 ms. 80 ms. 96 ms. 160 ms. 192 ms. 240 ms. 128 ms. DP Make Ratio 39 % Make Ratio 33 % Make Ratio BLADE RESET DTMF signal width...
Page 282 CM35 COMMAND CODE TITLE: TRUNK ROUTE DATA : Default SETTING DATA RELATED COMMAND MEANING DATA MEANING Interval of SLT/Multiline 0.4 seconds ON-0.2 seconds OFF-0.4 seconds Terminal ringing signal to ON-2 seconds OFF station on incoming calls 0.4 seconds ON-0.2 seconds OFF-0.4 seconds [North America Only] ON-2 seconds OFF 1 second ON-2 seconds OFF...
Page 283 CM35 COMMAND CODE TITLE: TRUNK ROUTE DATA : Default SETTING DATA RELATED COMMAND MEANING DATA MEANING Abbreviated Codes for speed Abbreviated Codes for System Speed Dialing CM71>66 calling for routing to C.O. assigned by CM71>66 CM72 line when all tie lines are busy NONE No data...
Page 284 CM35 COMMAND CODE TITLE: TRUNK ROUTE DATA : Default SETTING DATA RELATED COMMAND MEANING DATA MEANING Restriction of outgoing con- Restricted CM12 Y=01 nection Allow (Semi-Restricted-1) (RCD) Restriction of outgoing con- Restricted nection Allow (Semi-Restricted-2) (RCE) Restriction of outgoing con- Restricted nection Allow...
Page 285 CM35 COMMAND CODE TITLE: TRUNK ROUTE DATA : Default SETTING DATA RELATED COMMAND MEANING DATA MEANING Restriction of incoming Restricted CM12 Y=01 connection to station Allow (Semi-Restricted-2) (RCE) Restriction of incoming Restricted connection to station Allow (Restricted-1) (RCF) Restriction of incoming Restricted connection to station Allow...
Page 286 CM35 COMMAND CODE TITLE: TRUNK ROUTE DATA : Default SETTING DATA RELATED COMMAND MEANING DATA MEANING Designation of Area Code Area Code Development Pattern No. 0 CM8A Development Pattern No. for Y=4000-4007 Toll Restriction Area Code Development Pattern No. 7 CM85 Y=0-7 Analysis, and Maximum Not used...
Page 287 CM35 COMMAND CODE TITLE: TRUNK ROUTE DATA : Default SETTING DATA RELATED COMMAND MEANING DATA MEANING Common Channel Handler CCH00 CM30 Y=35 (CCH) number used for No. CMA7 7 CCIS/SIP CCH15 CMA8 NONE No data RESET NOTE: IPT (P2P CCIS) must be on CCH00. D Channel Handler (DCH) DCH00 number used for ISDN...
Page 288 CM35 COMMAND CODE TITLE: TRUNK ROUTE DATA Y=100-197 : Default SETTING DATA RELATED COMMAND MEANING DATA MEANING Kind of CCIS Trunk CCIS Trunk (T1) 2-wire E&M Trunk BLADE RESET NONE No data NOTE: When changing the data with online, the data is valid after the trunk blade is unplugged and plugged in. Call still Hold Available [Australia Only]...
Page 289 CM35 COMMAND CODE TITLE: TRUNK ROUTE DATA : Default SETTING DATA RELATED COMMAND MEANING DATA MEANING Forced release for tandem Available CM08>029 connection for incoming Not available CM41 Y=0>54 trunk Sending method of calling CALLER ID (CLASS SM) number from/to network T1-ANI [North America Only] Enhanced 911...
Page 290 CM35 COMMAND CODE TITLE: TRUNK ROUTE DATA : Default SETTING DATA RELATED COMMAND MEANING DATA MEANING Pursuit function after Roam- To provide ing PS Not provided [For PCS] NOTE: When using roaming service, set the [8300R2] second data to “0” for C.O. Trunk route of called side PBX.
Page 291 CM35 COMMAND CODE TITLE: TRUNK ROUTE DATA : Default SETTING DATA RELATED COMMAND MEANING DATA MEANING Calling party number is used Available CM2A Y=15, A0 as the ID Code for Remote Not available Access to System (DISA) NOTE: Assign this data only for Ring down connection.
Page 292 CM35 COMMAND CODE TITLE: TRUNK ROUTE DATA : Default SETTING DATA RELATED COMMAND MEANING DATA MEANING Multiline Terminal Ringer See below CM35 Y=034 Tone Pattern on incoming calls Multiline Terminal ringer tone pattern is assigned by the following combination of CM35 Y=034 and 164. : Default Y=34 Y=164: 0...
Page 293 CM35 COMMAND CODE TITLE: TRUNK ROUTE DATA : Default SETTING DATA RELATED COMMAND MEANING DATA MEANING Specification of charging Charging by C.O. line calls method No charge Alternate Routing for IPT To provide CM8A (P2P CCIS)/SIP Not provided CM35 Y=192 Trunk access code for Trunk Access Code to be added CM35 Y=044...
Page 294 CM35 COMMAND CODE TITLE: TRUNK ROUTE DATA Y=200-999 : Default SETTING DATA RELATED COMMAND MEANING DATA MEANING ISDN trunk tone sending To send Not sent Indication when a trunk is Trunk Route Name (4 characters) set to the Line Key of Multi- Trunk Route No.
Page 295 CM35 COMMAND CODE TITLE: TRUNK ROUTE DATA : Default SETTING DATA RELATED COMMAND MEANING DATA MEANING Release of ISDN trunk when Not released receiving the ISDN DIS- To release CONNECT message with Progress Description=08 from ISDN (effective for an incoming call from ISDN) NOTE: When sending the in-band tone to the called station from ISDN, set the second data to 0.
Page 296 CM35 COMMAND CODE TITLE: TRUNK ROUTE DATA : Default SETTING DATA RELATED COMMAND MEANING DATA MEANING Country Code for ETSI Country Code ISDN Addressing X: 0-9, A (*), B (#) [For EU] XXXX NONE No data Area Code for ETSI ISDN Area Code Addressing X: 0-9, A (*), B (#)
Page 297 CM35 COMMAND CODE TITLE: TRUNK ROUTE DATA : Default SETTING DATA RELATED COMMAND MEANING DATA MEANING Release of ISDN trunk when To release CM35 receiving the ISDN DIS- Not released Y=266, 158, 208 CONNECT message with Progress Description=08 from ISDN because the called party is busy in tan- dem connection (ISDN to ISDN)
Page 298 CM35 COMMAND CODE TITLE: TRUNK ROUTE DATA : Default SETTING DATA RELATED COMMAND MEANING DATA MEANING Forced release in designated To provide time for incoming trunk Not provided route Warning SST sending timer Depends on Timer A (CM41 Y=0>114) CM35 Y=247 for forced release to the Depends on Timer B (CM41 Y=0>115) CM41 Y=0>114...
Page 299 CM35 COMMAND CODE TITLE: TRUNK ROUTE DATA : Default SETTING DATA RELATED COMMAND MEANING DATA MEANING Specification of the call ter- To transfer to the VRS/another station/ CM35 Y=256, 258 minating method for incom- Attendant Console (assigned by CM51 Y=33) CM51 Y=33 ing call with no CLI in Night To reject the call termination...
Page 300 CM35 COMMAND CODE TITLE: TRUNK ROUTE DATA : Default SETTING DATA RELATED COMMAND MEANING DATA MEANING Dial Tone (DT) sending to To send DT of own office calling party of opposite To send DT of own office when the received office when receiving the Progress Description is not same as the Progress SETUP ACK message by...
Page 301 CM35 COMMAND CODE TITLE: TRUNK ROUTE DATA : Default SETTING DATA RELATED COMMAND MEANING DATA MEANING ISDN Alternative Routing Allow for Remote Unit in survival Restricted mode when receiving trunk call Call Completion to Busy Allow Subscriber (CCBS) for a call Restricted originating office [For EU]...
Page 302 CM35 COMMAND CODE TITLE: TRUNK ROUTE DATA : Default SETTING DATA RELATED COMMAND MEANING DATA MEANING Setting of PAD data from a -15 dB station to a trunk (1 dB increment) PRECAUTION (3) -1 dB 0 dB +1 dB (1 dB increment) +15 dB NONE 0 dB...
Page 303 CM36 COMMAND CODE TITLE: RESTRICTION DATA/PAD DATA FOR TANDEM CONNECTION FUNCTION: This command is used to assign restriction data and PAD data for tandem connection within a system, for each combination of an incoming trunk route and an outgoing trunk route. PRECAUTION: Any incoming trunk route assigned to “No release signal”...
Page 304 CM36 COMMAND CODE TITLE: RESTRICTION DATA/PAD DATA FOR TANDEM CONNECTION DATA TABLE: : Default INCOMING OUTGOING RELATED TRUNK TRUNK SETTING DATA COMMAND MEANING ROUTE ROUTE Setting of restric- Allow CM35 Y=005 tion data for tan- Restricted dem connection Setting of PAD aa bb aa : PAD data from an incoming CM35 Y=005...
Page 305 CM40 COMMAND CODE TITLE: FUNCTION OF CPU RS-232C PORT FUNCTION: This command is used to assign the function of the RS-232C ports on the CPU blade. The CPU blade has two RS-232C ports, which are used for the following purpose. u: To assign –: Not assigned ( ): Port Location Number RS-232C PORTS ON THE CPU BLADE UNIT01...
Page 306 CM40 COMMAND CODE TITLE: CPU RS-232C PORT u: To assign –: Not assigned ( ): Port Location Number RS-232C PORTS ON THE CPU BLADE UNIT01 UNIT02 UNIT03 UNIT04 FUNCTION REMARKS PORT PORT PORT PORT PORT PORT PORT PORT Remote Mainte- Available to use these ports nance using external at the same time...
Page 307 CM40 COMMAND CODE TITLE: CPU RS-232C PORT ASSIGNMENT PROCEDURE: PORT LOCATION NUMBER DATA 40YY + DE (0/1/4-7) (1-8 digits) DATA TABLE: CPU RS-232C port for PCPro/VoIP Log Collection/Built-in SMDR/MCI : Default SETTING DATA PORT LOCATION NUMBER REMARKS MEANING DATA MEANING Function UNIT01 PORT1 VoIP log collection...
Page 308 CM40 COMMAND CODE TITLE: CPU RS-232C PORT : Default SETTING DATA PORT LOCATION NUMBER REMARKS MEANING DATA MEANING RTS signal sent to UNIT01 PORT1 NOTE 3 terminal UNIT01 PORT2 High UNIT02 PORT1 CS control CS control is always [8300R2] NOTE 1 provided NOTE 6 UNIT02 PORT2...
Page 309 CM40 COMMAND CODE TITLE: CPU BUILT-IN MODEM CPU Built-In Modem : Default SETTING DATA PORT LOCATION NUMBER REMARKS MEANING DATA MEANING Station number of Fixed Built-in modem No. CM08>909 built-in modem X: 0-9, A (*), B (#) NOTE 1 XXXXXXXX NOTE 2 RESET NONE...
Page 310 CM41 COMMAND CODE TITLE: SYSTEM TIMER DATA FUNCTION: This command is used to assign the System Timer data. PRECAUTION: None ASSIGNMENT PROCEDURE: 1ST DATA 2ND DATA + 41Y + (2 digits) (2 digits) DATA TABLE: 2ND DATA INCREMENT MEANING DEFAULT DATA UNIT TIMER...
Page 311 CM41 COMMAND CODE TITLE: SYSTEM TIMER DATA 2ND DATA INCREMENT MEANING DEFAULT DATA UNIT TIMER Timing for Pseudo- NONE 00 01 02 03 04 05 06 07 08 Answer signal sent to 12 16 20 24 28 32 36 SMDR 4 seconds 12 16 20 24 28 32 36 40 seconds...
Page 312 CM41 COMMAND CODE TITLE: SYSTEM TIMER DATA 2ND DATA INCREMENT MEANING DEFAULT DATA UNIT TIMER Attendant Recall of NONE 01 02 03 04 05 06 ....... 13 held call 31.2 2.4 4.8 7.2 9.6 12.0 ....28.8 31.2 2.4 seconds [8300R2] 33.6 2.4 4.8 7.2 9.6 12.0 14.4 ....
Page 313 CM41 COMMAND CODE TITLE: SYSTEM TIMER DATA 2ND DATA INCREMENT MEANING DEFAULT DATA UNIT TIMER Unanswered timing NONE 01 02 03 ............30 for ACD/UCD Delay 8 ............116 Announcement and Attendant Delay 12 ............120 Announcement seconds 4 seconds Maximum ACD/UCD NONE 01 02 03 ............30 call waiting time 8 ............116...
Page 314 CM41 COMMAND CODE TITLE: SYSTEM TIMER DATA 2ND DATA INCREMENT MEANING DEFAULT DATA UNIT TIMER Automatic Recall NONE 01 02 03 04 05 .........15 Timing of Camp-On 16 24 32 40 ........120 8 seconds 16 24 32 40 48........128 seconds Interdigit Pause on NONE 03 04 05 06 07 .........14...
Page 315 CM41 COMMAND CODE TITLE: SYSTEM TIMER DATA 2ND DATA INCREMENT MEANING DEFAULT DATA UNIT TIMER Programmable Pause NONE 00 01 02 03 04 05 06 07 for System Speed 1.5 3.0 4.5 6.0 7.5 9.0 10.5 12.0 Dialing/Station Speed 1.5 seconds seconds NOTE: This pause is available by setting “D”...
Page 316 CM41 COMMAND CODE TITLE: SYSTEM TIMER DATA 2ND DATA INCREMENT MEANING DEFAULT DATA UNIT TIMER Announcement Ser- NONE 01 02 ..............99 vice Timer 4 ..............392 4 seconds 8 ..............396 seconds Timing of Multiple NONE 01 02 03 ..........29 Call Forwarding No 8 ..........
Page 317 CM41 COMMAND CODE TITLE: SYSTEM TIMER DATA 2ND DATA INCREMENT MEANING DEFAULT DATA UNIT TIMER Message Replay Timer NONE 01 02 03 ............31 for Automated Atten- 12 ............124 dant 12 16 ............128 seconds NOTE: In case that the recording time of Voice Re- 4 seconds sponse System is shorter than the time assigned by command (CM41Y=0>51), Voice Response...
Page 318 CM41 COMMAND CODE TITLE: SYSTEM TIMER DATA 2ND DATA INCREMENT MEANING DEFAULT DATA UNIT TIMER Forced release timing NONE 01 02 03 04 ..........13 for unanswered call 12 16 20 ..........56 with tandem connec- tion or trunk to trunk 4 seconds 12 16 20 24 ..........60 connection when a sta- seconds...
Page 319 CM41 COMMAND CODE TITLE: SYSTEM TIMER DATA 2ND DATA INCREMENT MEANING DEFAULT DATA UNIT TIMER Path On Delay timer NONE 01 02 03 ............14 when answering 0 160 320 ............2080 incoming trunk call 160 ms. 160 320 480 ............2240 SST Sending Timer NONE 01 02 03 ............14 when accessing Pag-...
Page 320 CM41 COMMAND CODE TITLE: SYSTEM TIMER DATA 2ND DATA INCREMENT MEANING DEFAULT DATA UNIT TIMER UCD Delay NONE 01 02 03 ............32 Announcement/ 8 ............124 Attendant Delay 4 seconds Announcement/OAI 12 ............128 Announcement Con- seconds nection Timer Recall interval timer NONE 45 46 ..............99 of CPU built-in...
Page 321 CM41 COMMAND CODE TITLE: SYSTEM TIMER DATA 2ND DATA INCREMENT MEANING DEFAULT DATA UNIT TIMER Message reply timer NONE 01 02 ..............99 for PS No Answer 4 ..............392 4 seconds 8 ..............396 seconds NOTE: Effective only when CM08>085: 0. Timer of Dial Tone NONE 05 06 07 ............30 sending after Off-...
Page 322 CM41 COMMAND CODE TITLE: SYSTEM TIMER DATA 2ND DATA INCREMENT MEANING DEFAULT DATA UNIT TIMER SPDT Timer after NONE 10 11 12 ............60 Hooking 1 second 10 11 12 ............60 seconds DTMF signal width on NONE 04 05 06 ............15 16 ms.
Page 323 CM41 COMMAND CODE TITLE: SYSTEM TIMER DATA 2ND DATA INCREMENT MEANING DEFAULT DATA UNIT TIMER Timer B of warning NONE 01 02 03 ............99 SST sending for – 64 128 192 ............6336 forced release NOTE: Set the time from the start of communications 64 seconds to the warning SST is sent.
Page 324 CM41 COMMAND CODE TITLE: SYSTEM TIMER DATA 2ND DATA INCREMENT MEANING DEFAULT DATA UNIT TIMER Expire value for NONE 00 01 02 ............99 DT700 Series REGIS- 2 ............99 TER (Day) seconds RESET NOTE 1: Usually, this data setting is not required. NOTE 2: This data implies the expire value for the DT700 Series REGISTER (terminal registration) and is set by the...
Page 325 CM41 COMMAND CODE TITLE: SYSTEM TIMER DATA 2ND DATA INCREMENT MEANING DEFAULT DATA UNIT TIMER Expire value for NONE 00 01 02 ............99 DT700 Series SUB- 3600 2 ............99 SCRIBE for Server seconds (Day) NOTE 1: Usually, this data setting is not required. RESET NOTE 2: This data implies the expire value for the DT700 Series...
Page 326 CM41 COMMAND CODE TITLE: SYSTEM TIMER DATA 2ND DATA INCREMENT MEANING DEFAULT DATA UNIT TIMER Expire value for NONE 00 01 02 ............99 DT700 Series SUB- 3600 2 ............99 SCRIBE for Client seconds (Day) NOTE 1: Usually, this data setting is not required. RESET NOTE 2: This data implies the expire value for the DT700 Series...
Page 327 CM41 COMMAND CODE TITLE: SYSTEM TIMER DATA 2ND DATA INCREMENT MEANING DEFAULT DATA UNIT TIMER Conference (built-in NONE 01 02 03 ............24 CPU) forced release 7 hours 3 ............24 1 hour timer NOTE: If this data set to “00”, Forced release is not [8300R2] provided hours.
Page 328 CM41 COMMAND CODE TITLE: SYSTEM TIMER DATA 2ND DATA INCREMENT MEANING DEFAULT DATA UNIT TIMER Delayed Ringing NONE 03 ..........20 2048 ms. Timer 10240 ms. 2048 4096 6144 ..........40960 On-Hook Detect NONE 01 02 03 ............60 Timer 20 ms. 700 ms. 20 40 60 ............1200 BLADE RESET Continued on next page...
Page 329 CM41 COMMAND CODE TITLE: SYSTEM TIMER DATA 2ND DATA INCREMENT MEANING DEFAULT DATA UNIT TIMER C.O. Trunk Termina- NONE 01 02 03 ............99 tion Detect Timer 8 ms. 224 ms. 16 24 ............792 BLADE RESET Single Ringing Detect NONE 01 02 03 ..........98 16 ms.
Page 330 CM41 COMMAND CODE TITLE: SYSTEM TIMER DATA 2ND DATA INCREMENT MEANING DEFAULT DATA UNIT TIMER COT Ground Start- NONE 01 02 03 ..........98 8 ms. ing Timer 48 ms. 16 24 ..........784 2040 (01-98) BLADE RESET OD Trunk Answer NONE 01 02 03 ..........98 20 ms.
Page 331 CM41 COMMAND CODE TITLE: SYSTEM TIMER DATA 2ND DATA INCREMENT MEANING DEFAULT DATA UNIT TIMER LD Wink signal send- NONE 01 02 03 ..........98 ing time for connection 20 ms. 200 ms. 20 40 60 ...........1960 2550 check (01-98) BLADE RESET LD Trunk Wink/Delay NONE 01 02 03 ..........98...
Page 332 CM41 COMMAND CODE TITLE: SYSTEM TIMER DATA 2ND DATA INCREMENT MEANING DEFAULT DATA UNIT TIMER Release Signal Detect NONE 01 02 03 ............15 Timing for C.O. trunk 512 ms. 64 128 192 ............960 64 ms. NOTE: If CM35 Y=009 is set to “01” or “15”, use CM41 Y=3> 05-12.
Page 333 CM41 COMMAND CODE TITLE: SYSTEM TIMER DATA 2ND DATA INCREMENT MEANING DEFAULT DATA UNIT TIMER Ground Start Release NONE 01 02 03 ............15 (Ground Off) Detect 384 ms. 64 128 192 ............960 64 ms. Timing for DTI Trunk NOTE: If CM35 Y=009 is set to “01” or “15”, use CM41 Y=3> 05-12.
Page 334 CM41 COMMAND CODE TITLE: SYSTEM TIMER DATA 2ND DATA INCREMENT MEANING DEFAULT DATA UNIT TIMER DTI Wink signal send- NONE 01 02 03 ..........98 ing time for connection 16 ms. 200 ms. 16 32 48 ...........1568 2040 check (01-98) BLADE RESET DTI Trunk Wink/ NONE 01 02 03 ..........98...
Page 335 CM42 COMMAND CODE TITLE: SYSTEM COUNTER DATA/PAD DATA/TRUNK RESTRICTION CLASS CONVERSION/CODEC LIST FUNCTION: This command is used to set the system counter data, the programmable PAD data, the Trunk Restriction Class data to convert the Restriction Class sent to or from the 2400 IPX as a Deluxe Traveling Class Mark-CCIS, and CODEC list.
Page 336 CM42 COMMAND CODE TITLE: SYSTEM COUNTER DATA DATA TABLE: System Counter Data : Default KIND OF SYSTEM COUNTER SETTING DATA REMARKS Number of waiting calls which will cause 1 call attendant’s CWXX on LCD to flash [DESKCON] 48 calls [8300R2] NONE 6 calls NOTE:...
Page 337 CM42 COMMAND CODE TITLE: SYSTEM COUNTER DATA : Default KIND OF SYSTEM COUNTER SETTING DATA REMARKS Maximum number of digits for Account Code 1 digit with OAI (SCF) 10 digits NONE 10 digits Maximum number of digits for Account Code 1 digit with CPU 16 digits...
Page 338 CM42 COMMAND CODE TITLE: SYSTEM COUNTER DATA : Default KIND OF SYSTEM COUNTER SETTING DATA REMARKS Maximum number of calls in queue in each 1 call UCD group for controlling external indicator 99 calls or Call Waiting lamp of Multiline Terminal NONE 1 call Maximum number of calls in queue in each...
Page 339 CM42 COMMAND CODE TITLE: SYSTEM COUNTER DATA : Default KIND OF SYSTEM COUNTER SETTING DATA REMARKS Volume Control (Side tone level) of Multiline –54 dB 6 dB Terminal/DESKCON increments –18 dB RESET NONE –30 dB NOTE 1: Do not change this data normally, incorrect data settings may cause howler of low-level speech. NOTE 2: For the volume control (Side tone level) of DT300/DT700 series, set the data by CM42>198.
Page 340 CM42 COMMAND CODE TITLE: TRUNK RESTRICTION CLASS CONVERSION Trunk Restriction Class Conversion SV8300 represents small model PBX system. 2400 IPX represents medium to large model PBX system. : Default 1ST DATA 2ND DATA REMARKS DATA MEANING DATA MEANING SV8300 Trunk Restriction Class 1 (RCA) 2400 IPX Trunk Restriction Class (0-15) SV8300 Trunk Restriction Class 2 (RCB)
Page 341 CM42 COMMAND CODE TITLE: TRUNK RESTRICTION CLASS CONVERSION NOTE 1: Default in the DATA TABLE represents the value for the data “NONE”. In this case, the fol- lowing conversion is performed in the Deluxe Traveling Class Mark-CCIS. (1) 2400 IPX to SV8300 2400 IPX SV8300 TRK RESTRICTION CLASS...
Page 342 CM42 COMMAND CODE TITLE: CODEC LIST CODEC List : Default 1ST DATA (CODEC TYPE) 2ND DATA REMARKS DATA MEANING DATA MEANING Priority 1-4 in CODEC list 0 G.711 µ-law 64 K CM67 G.711 A-law 64 K G.723.1 NOTE 1 G.729a Priority 1-4 in CODEC list 1 G.722 (Wide Band Codec) NOTE 2...
Page 343 CM42 COMMAND CODE TITLE: CODEC LIST NOTE 1: The following payload size can be assigned for each CODEC type. G.711 : 10 ms./20 ms./30 ms./40 ms. G.722 : 10 ms./20 ms./30 ms./40 ms. G.723.1: 30 ms. G.729a : 10 ms./20 ms./30 ms./40 ms. NOTE 7 on CM67 Y=00 NOTE 2: When the payload size setting differs from that for the opposite VoIPDB, the shorter size is...
Page 344 CM42 COMMAND CODE TITLE: CODEC LIST : Default 1ST DATA 2ND DATA REMARKS DATA MEANING DATA MEANING Room Status Code set by Check In operation Room Status Code 1 Room Status Code set by Check Out operation Room Status Code 8 Room Status Code when pressing Call NONE Not used...
Page 345 CM42 COMMAND CODE TITLE: CODEC LIST : Default 1ST DATA 2ND DATA REMARKS DATA MEANING DATA MEANING Time to lock the DT700 Series when number Not unlocked of password entries exceeded the limit 1 minute 99 minutes NONE 10 minutes NOTE: When the DT700 Series is in password lock state, a password entry is restricted until the time set by this command is elapsed.
Page 346 CM42 COMMAND CODE TITLE: CODEC LIST : Default 1ST DATA 2ND DATA REMARKS DATA MEANING DATA MEANING Time for monitoring long-time call duration of 1 minute trunk call in Call Charge Immediate Printout/ Call Charge Printout for individual station/ 99 minutes Call Charge Printout of a long-time call NONE Not monitored...
Page 347 CM43 COMMAND CODE TITLE: PERIODIC MAINTENANCE/IP STATION FIRMWARE AUTOMATIC UPDATE/SYSTEM DATA COPY/AUTOMATIC CLOCK CHANGE FUNCTION: This command is used to set the date, time and check item for periodic maintenance. The fault informa- tion display reminds you of the time for each periodic maintenance. [See CMEA Fault Information Display, fault kind No.
Page 348 CM43 COMMAND CODE TITLE: PERIODIC MAINTENANCE/IP STATION FIRMWARE AUTOMATIC UPDATE/SYSTEM DATA COPY/AUTOMATIC CLOCK CHANGE : Default MEANING MEANING 2ND DATA MEANING DATA 6 Time setting for IP IP Station firmware YYYY MM DD HH mm YYYY: Year (2008-2099) Station firmware auto- automatic update time : Month (01-12) matic update...
Page 349 CM43 COMMAND CODE TITLE: PERIODIC MAINTENANCE/IP STATION FIRMWARE AUTOMATIC UPDATE/SYSTEM DATA COPY/AUTOMATIC CLOCK CHANGE : Default MEANING MEANING 2ND DATA MEANING DATA 8 Time setting for Reading of system clock YYYY MM DD YYYY: Year (2008-2099) Automatic clock changed day from : Month (01-12) change standard time to...
Page 350 CM44 COMMAND CODE TITLE: EXTERNAL RELAY STARTING CONDITIONS FUNCTION: This command is used to assign the relay circuit number and Relay Group number of PGD(2)-U10 ADP/ External Relay Interface of CPU blade used for controlling external relay. PRECAUTION: For External Relay Interface of the CPU blade, assign 312, 313 (blade No. 31, circuit No. 2, 3). ASSIGNMENT PROCEDURE: RELAY RELAY...
Page 351 CM44 COMMAND CODE TITLE: EXTERNAL RELAY STARTING CONDITIONS : Default DATA 1 DATA 2 REMARKS DATA MEANING DATA MEANING Speaker Paging Machine Start Speaker Paging Zone 0 CM12 Y=68 CM20 Speaker Paging Zone 9 Indication for Trunk All Busy Trunk Group 01 CM30 Y=09 Trunk Group 62 TAS Indication...
Page 352 CM44 COMMAND CODE TITLE: EXTERNAL RELAY STARTING CONDITIONS The following table shows the interface condition of each external relay. EQUIPMENT KIND INTERFACE RELATED COMMAND REMARKS Speaker Paging DLC + PGD(2)-U10 ADP • CM05 Y=0 • Start by External Relay Control •...
Page 353 CM44 COMMAND CODE TITLE: EXTERNAL RELAY STARTING CONDITIONS EQUIPMENT KIND INTERFACE RELATED COMMAND REMARKS Indication for ACD/UCD CPU Built-in Relay • CM17 • Start by CPU Built-in Relay Call Waiting • CM44 Y=00>312, 313: 14XX DLC + PGD(2)-U10 ADP • CM05 Y=0 •...
Page 354 CM45 COMMAND CODE TITLE: MAKE BUSY CONDITION OF CFT FUNCTION: This command is used to define the make busy condition of CFT. PRECAUTION: None ASSIGNMENT PROCEDURE: CFT NUMBER DATA + 45Y + (2 digits) (1 digit) DATA TABLE: : Default CFT NUMBER SETTING DATA RELATED...
Page 355 CM48 COMMAND CODE TITLE: HOLD/WAKE UP/TIMED REMINDER/AUTOMATED ATTENDANT TONE FUNCTION: This command determines the kind of tone/tone source on various services; it also determines whether the Announcement Service is provided when a PS does not answer in a Wireless Communication Sys- tem.
Page 356 CM48 COMMAND CODE TITLE: HOLD/WAKE UP/TIMED REMINDER/AUTOMATED ATTENDANT TONE DATA TABLE: : Default SENDING PATTERN SETTING DATA RELATED COMMAND MEANING PATTERN MEANING DATA MEANING Hold Tone C.O. Line 0000 No Tone Sending Tie Line 0500 Hold Message CM49 Y=00 Station 1300 Hold Tone Source on CPU blade/External...
Page 357 CM48 COMMAND CODE TITLE: HOLD/WAKE UP/TIMED REMINDER/AUTOMATED ATTENDANT TONE : Default SENDING PATTERN SETTING DATA RELATED COMMAND MEANING PATTERN MEANING DATA MEANING Wake Up Tone source of 0000 No Tone Call/Timed Wake Up Call/ 0200 External Tone Source CM44 Reminder Timed Reminder Y=00: 0100 RESET...
Page 358 CM48 COMMAND CODE TITLE: HOLD/WAKE UP/TIMED REMINDER/AUTOMATED ATTENDANT TONE : Default SENDING PATTERN SETTING DATA RELATED COMMAND MEANING PATTERN MEANING DATA MEANING Dial Tone Progress Tone for Not provided sending Last Number To provide Redial and Speed Dial when Using 2nd DT sending on To provide ISDN trunks...
Page 359 CM48 COMMAND CODE TITLE: HOLD/WAKE UP/TIMED REMINDER/AUTOMATED ATTENDANT TONE : Default SENDING PATTERN SETTING DATA RELATED COMMAND MEANING PATTERN MEANING DATA MEANING Music selec- Music selection Nocturne tion for Inter- for Internal Hold Minuet nal Hold Tone Fur Elise Tone The Maiden’s Prayer When the saints go marching in...
Page 360 CM48 COMMAND CODE TITLE: HOLD/WAKE UP/TIMED REMINDER/AUTOMATED ATTENDANT TONE : Default SENDING PATTERN SETTING DATA RELATED COMMAND MEANING PATTERN MEANING DATA MEANING Announce- – 0500 To provide CM12 Y=04 ment PS No NONE Not provided CM41 Y=0>01, Answer [8300R2] CM49 Y=00, 10 Announce- –...
Page 361 CM49 COMMAND CODE TITLE: VOICE RESPONSE SYSTEM FUNCTION: This command is used to define the function of each Voice Response System (VRS) accommodated into the system. PRECAUTION: None ASSIGNMENT PROCEDURE: TENANT DATA NUMBER NUMBER + 49YY + (2-5 digits) (3 digits) (2 digits) DATA TABLE: SETTING DATA...
Page 362 CM49 COMMAND CODE TITLE: VOICE RESPONSE SYSTEM SETTING DATA VRS No./ RELATED TENANT No. COMMAND MEANING DATA MEANING Function of Voice 000-007: 03000 Night Announcement Service CM30 Y=02-05 Response System VRS number 04 X Z X: Announcement Service CM15 Y=034-039 Group (0-4) CM35 Y=069-073 Z: Announcement Service...
Page 363 CM49 COMMAND CODE TITLE: VOICE RESPONSE SYSTEM SETTING DATA VRS No./ RELATED TENANT No. COMMAND MEANING DATA MEANING Function of Voice 000-007: 0F XX Attendant Delay CM49 Y=0A, Response System VRS number Announcement CM35 Y=074, XX: Message No. (00-63) CM41 Y=0>16, 47 [8300R2] Announcement Service for CM15 Y=59...
Page 364 CM49 COMMAND CODE TITLE: VOICE RESPONSE SYSTEM : Default SETTING DATA VRS No./ RELATED TENANT No. COMMAND MEANING DATA MEANING Function of Voice 000-007: 17 XX Voice Guide CM15 Y=116 Response System VRS number XX: Message No. (00-63) CM49 Y=13 CM48 Y=2 CM41 Y=0>53 1800...
Page 365 CM49 COMMAND CODE TITLE: VOICE RESPONSE SYSTEM : Default SETTING DATA VRS No./ RELATED TENANT No. COMMAND MEANING DATA MEANING Message No. of 00-63: Tenant No. 00-63 Message No. assigned by CM49 Y=00 Transferred Trunk CM49 Y=00 CM65 Y=50 Line (No Answer) Tenant No.
Page 366 CM49 COMMAND CODE TITLE: VOICE RESPONSE SYSTEM : Default SETTING DATA VRS No./ RELATED TENANT No. COMMAND MEANING DATA MEANING Message No. of Voice 00: When Message 00-63 Message No. assigned by CM48 Y=2 Guide NOTE waiting is set CM49 Y=00 CM49 Y=00>17XX 01: When service is NONE...
Page 367 CM4A COMMAND CODE TITLE: DAY/NIGHT MODE CHANGE BY SYSTEM CLOCK FUNCTION: This command is used to assign the schedule of Day/Night Mode Change by System Clock. PRECAUTION: For the normal operation of Day/Night Mode Change by System Clock, Day/Night Mode Change by the external key, by service access code or feature key, by Attendant Console should not be executed.
Page 368 CM4A COMMAND CODE TITLE: DAY/NIGHT MODE CHANGE BY SYSTEM CLOCK DATA TABLE: : Default 1ST DATA 2ND DATA MEANING DATA MEANING DATA MEANING Calendar No. 00-63 Tenant No. 00-63 Calendar No. 1 Calendar No. 2 Calendar No. 3 Calendar No. 4 NONE No data Data clear...
Page 369 CM4A COMMAND CODE TITLE: DAY/NIGHT MODE CHANGE BY SYSTEM CLOCK : Default 1ST DATA 2ND DATA MEANING DATA MEANING DATA MEANING Time schedule No. 0 XX ZZ XX : 00-23: Hour Day Mode Time schedule No. 1 ZZ : 00-55: Minute Night Mode Time schedule No.
Page 370 CM4A COMMAND CODE TITLE: DAY/NIGHT MODE CHANGE BY SYSTEM CLOCK • Default Pattern By assigning CM4A Y=90; Default Pattern No. 0-3, you can simplify the schedule assignment for each tenant. The schedule of each Default Pattern can be changed after the Default Pattern has been assigned. The following shows the summary of the Default Pattern and the schedule set by each Default Pattern.
Page 371 CM4A COMMAND CODE TITLE: DAY/NIGHT MODE CHANGE BY SYSTEM CLOCK Default Pattern of Time Schedule (CM4A Y=90) • Default Pattern No. 0 (CM4A Y=90 2nd data: 00) CM4A Y No. MEANING OF SETTING 00-63 Calendar No. 1 is used for the tenant 0101-1231 Week schedule No.
Page 372 CM4A COMMAND CODE TITLE: DAY/NIGHT MODE CHANGE BY SYSTEM CLOCK Default Pattern of Time Schedule (CM4A Y=90) • Default Pattern No. 2 (CM4A Y=90 2nd data: 02) CM4A Y No. MEANING OF SETTING 00-63 Calendar No. 3 is used for the tenant 0101-1231 Week schedule No.
Page 373 CM4B COMMAND CODE TITLE: ROOM STATUS CODE FUNCTION: This command is used to assign the functions for each Room Status Code which is dialed from a guest room or a Front Desk Terminal. PRECAUTION: None ASSIGNMENT PROCEDURE: 1ST DATA 2ND DATA + 4BYY + + EXE (3 digits)
Page 374 CM4B COMMAND CODE TITLE: ROOM STATUS CODE DATA TABLE: : Default 1ST DATA 2ND DATA RELATED COMMAND DATA MEANING DATA MEANING Change of Trunk Restriction Unrestricted (RCA) Class Non-Restricted 1 (RCB) X: Room Status Code 1-8 Non-Restricted 2 (RCC) Semi-Restricted 1 (RCD) Semi-Restricted 2 (RCE) Restricted 1 (RCF) Restricted 2 (RCG)
Page 375 CM50 COMMAND CODE TITLE: COMMON ROUTE INDIAL FUNCTION: This command is used to assign LDNs (Listed Directory Numbers) to common route indial lines. When these numbers are dialed into the system (either on an incoming tie line or an incoming C.O. line set up for indialing), the call will appear at a specified call identification key on the attendant console.
Page 376 CM50 COMMAND CODE TITLE: COMMON ROUTE INDIAL DATA TABLE: : Default KIND OF DATA SETTING DATA CODE MEANING DATA MEANING Two leading digits to be added Digits to be added NOTE 1: CM35 Y=017 allows digits to be added or (2 digits) NONE No data...
Page 377 CM50 COMMAND CODE TITLE: COMMON ROUTE INDIAL : Default KIND OF DATA SETTING DATA CODE MEANING DATA MEANING Effective data in CM35 Y=015 Dialed number NOTE 2 LDN 0 key (Data 00 in CM90) XXXX LDN 7 key (Data 07 in CM90) NOTE 1 (1-4 digits) NONE...
Page 378 CM50 COMMAND CODE TITLE: COMMON ROUTE INDIAL : Default KIND OF DATA SETTING DATA CODE MEANING DATA MEANING Pattern number for adding an access code for outgo- Access Code for outgoing ing call to the calling number recalled by Message call Reminder when terminating a tandem call via CCIS XXXXXX...
Page 379 CM51 COMMAND CODE TITLE: AUTOMATIC TRANSFER DESTINATIONS FUNCTION: This command is used to define destinations for different types of diversion. PRECAUTION: None ASSIGNMENT PROCEDURE: GROUP DATA + 51YY + NUMBER (1-8 digits) (2 digits) DATA TABLE: : Default GROUP NUMBER SETTING DATA MEANING DATA...
Page 380 CM51 COMMAND CODE TITLE: AUTOMATIC TRANSFER DESTINATIONS : Default GROUP NUMBER SETTING DATA MEANING DATA MEANING DATA MEANING Same as CM51 Y=06 (for station call) Tenant 00 E000 Attendant Console [8300R2] Tenant 63 EB000 Voice Response System No. EB007 NONE No data Transfer destination of incoming call when a Station No.
Page 381 CM51 COMMAND CODE TITLE: AUTOMATIC TRANSFER DESTINATIONS : Default GROUP NUMBER SETTING DATA MEANING DATA MEANING DATA MEANING Transfer destination of the call when a station ATT Group 0 Station No. dials the operator access code of Attendant ATT Group 1 Console is in Night Mode ATT Group 2 XXXXXXXX...
Page 382 CM51 COMMAND CODE TITLE: AUTOMATIC TRANSFER DESTINATIONS : Default GROUP NUMBER SETTING DATA MEANING DATA MEANING DATA MEANING Destination of the call after the first time inter- Tenant 00 Station No. val of ACD/UCD Display Announcement Tenant 63 XXXXXXXX E000 Attendant Console [8300R2] NONE...
Page 383 CM51 COMMAND CODE TITLE: AUTOMATIC TRANSFER DESTINATIONS : Default GROUP NUMBER SETTING DATA MEANING DATA MEANING DATA MEANING Destination of Attendant Overflow Tenant 00 Station No./Vir- [8300R2] tual Line Station Tenant 63 XXXXXXXX No. assigned by CM11 NONE No data Destination of Call Forwarding-Logout EB000 Voice Response...
Page 384 CM52 COMMAND CODE TITLE: HOT LINE/DELAYED HOTLINE FUNCTION: This command is used to assign a Hot Line/Delayed Hotline to stations, Attendant Consoles and trunks. PRECAUTION: The maximum number of Hot Lines/Delayed Hotlines is 100, and the connection is one-way from calling side to called side.
Page 385 CM52 COMMAND CODE TITLE: HOT LINE/DELAYED HOTLINE DATA TABLE: Hot Line/Delayed Hotline : Default SETTING DATA CALLING/CALLED MEANING DATA MEANING Hot Line/Delayed Calling Side Station No./Virtual Station No. Hotline Pair CM12 Y=03 number 00-99 XXXXXXXX NOTE NONE No data Called Side Station No.
Page 386 CM53 COMMAND CODE TITLE: TRUNK ANSWER FROM ANY STATION RESTRICTION FUNCTION: This command is used to define the conditions for Trunk Answer from Any Station (TAS) service. PRECAUTION: None ASSIGNMENT PROCEDURE: CONDITION CODE DATA + DE (1 digit) (1 digit) DATA TABLE: : Default CONDITION...
Page 387 CM56 COMMAND CODE TITLE: PAGING GROUP/INTERCOM GROUP FUNCTION: This command is used to assign the Multiline Terminal station number for Automatic/Manual/Dial In- tercom and Internal Zone Paging. PRECAUTION: None ASSIGNMENT PROCEDURE: SERIAL No. INTERCOM No. DATA + DE 56YY (2 digits) (4 digits) (1-8 digits) DATA TABLE:...
Page 388 CM56 COMMAND CODE TITLE: PAGING GROUP/INTERCOM GROUP SETTING DATA INTERCOM No./ RELATED SERIAL No. COMMAND MEANING DATA MEANING Manual Intercom A200 My Line number of CM11 number Multiline Terminal CM12 Y=03 A700 XXXXXXXX CM90 A201 CM08>238 A701 A224 A724 Dial Intercom number B000 My Line number of CM11...
Page 389: Group Call
CM57 COMMAND CODE TITLE: GROUP CALL FUNCTION: This command is used to assign the Group Call numbers and stations for Group Call by Pilot Number Dialing. PRECAUTION: None ASSIGNMENT PROCEDURE: 1ST DATA 2ND DATA + DE 57YY (2/4 digits) (1-8 digits) DATA TABLE: : Default 1ST DATA...
Page 390 CM58 COMMAND CODE TITLE: LDN DIVERSION FUNCTION: This command is used to assign information to each DID or TIE trunk for which incoming calls are to be redirected to an alternative destination. PRECAUTION: This data is valid when CM08>205 is assigned to “0”. ASSIGNMENT PROCEDURE: LDN/TIE DATA...
Page 391 CM58 COMMAND CODE TITLE: LDN DIVERSION : Default SETTING DATA MEANING DATA MEANING Tenant number of LDN assigned by Tenant 00 CM50 Y=01 Tenant 63 NONE No data TAS group number assigned by TAS Group 00 CM44>13 TAS Group 63 NONE No data Day Mode destination of LDN...
Page 392 CM58 COMMAND CODE TITLE: LDN DIVERSION : Default SETTING DATA MEANING DATA MEANING Day Mode diversion for non-answer- Attendant Console “NANS” Key ing destination station Not used CM53 NONE No data Night Mode diversion for non- Same as CM58 Y=06 answering destination station NONE No data...
Page 393 CM59 COMMAND CODE TITLE: TAS/ACD/UCD RELAY INTERRUPTION PATTERN FUNCTION: This command is used to assign the interruption pattern on the TAS and ACD/UCD indicators controlled via External Relay Interface of CPU. PRECAUTION: None ASSIGNMENT PROCEDURE: FUNCTION DATA + 59 + NUMBER (2 digits) (2 digits)
Page 394 CM5B COMMAND CODE TITLE: IP ADDRESS FOR IP TRUNK POINT-TO-MULTIPOINT CONNECTION FUNCTION: This command is used to assign the destination IP Address for the IP trunk Point-to-Multipoint connec- tion. PRECAUTION: None ASSIGNMENT PROCEDURE: 1ST DATA 2ND DATA + DE 5BYY (5 digits) (12 digits) DATA TABLE:...
Page 395 CM60 COMMAND CODE TITLE: ATT TENANT GROUP, FUNCTIONS FUNCTION: This command is used to assign a number to a Desk Console for access on a tenant basis, and define the consoles’ night switching ability, off-hook ringing, tone ringer, password code for Attendant Lockout and Attendant Programming.
Page 396 CM60 COMMAND CODE TITLE: ATT TENANT GROUP, FUNCTIONS DATA TABLE: : Default GROUP NUMBER RELATED COMMAND MEANING DATA MEANING ATT GROUP NOTE 2 ATT GROUP 0 CM62 ATT GROUP 1 CM51 Y=13 ATT GROUP 2 CM60 Y=90 ATT GROUP 3 NONE No data Designation of Master ATT within...
Page 397 CM60 COMMAND CODE TITLE: ATT TENANT GROUP, FUNCTIONS : Default GROUP NUMBER RELATED COMMAND MEANING DATA MEANING Tone Ringer for DESKCON 600 + 700 u 16 (Hz) CM60 Y=90 NOTE 2 480 + 606 u 8 (Hz) 1024 + 1285 u 16 (Hz) 480 + 606 u 16 (Hz) Password for DESKCON Password (Maximum 8 digits)
Page 398 CM60 COMMAND CODE TITLE: ATT TENANT GROUP, FUNCTIONS : Default GROUP NUMBER RELATED COMMAND MEANING DATA MEANING Tenant number for DESKCON Tenant No. 00 [8300R2] Tenant No. 63 NONE No data Ringing signal patterns of 0.5ON-0.5OFF DESKCON 1sON-1sOFF [8300R2] 2sON-4sOFF 1sON-2sOFF DESKCON number for PS-display DESKCON No.
Page 399 CM61 COMMAND CODE TITLE: EXTERNAL KEY FUNCTION FUNCTION: This command is used to activate and specify the function of the switch closure detection PGD(2)-U10 ADP when interfaced with external keys. PRECAUTION: None ASSIGNMENT PROCEDURE: KEY NUMBER DATA + DE 61YY (3 digits) (1-2 digits) DATA TABLE:...
Page 400 CM61 COMMAND CODE TITLE: EXTERNAL KEY FUNCTION : Default KEY NUMBER SETTING DATA RELATED COMMAND MEANING MEANING DATA MEANING Service operation by exter- XX Z XX: Key Group No. MJ/MN Alarm nal key (00-63) assigned by Clear key CM12 Y=66 Day/Night Mode Z : Circuit No.
Page 401 CM62 COMMAND CODE TITLE: TENANTS FOR EACH ATT GROUP FUNCTION: This command is used to assign which tenants are handled by each DESKCON Group. [8300R2] PRECAUTION: This command requires a reset by CM60 Y=90>0: 0 after data setting. Multiple tenants can be assigned to one ATT Group, but one tenant cannot be assigned to more than one ATT Group.
Page 402 CM63 COMMAND CODE TITLE: RESTRICTION OF INTER-TENANT CONNECTION FUNCTION: This command is used to define the restrictions on inter-tenant access. PRECAUTION: None ASSIGNMENT PROCEDURE: TENANT-A TENANT-B DATA + DE (2 digits) (2 digits) (1 digit) DATA TABLE: : Default TENANT SETTING DATA RELATED COMMAND...
Page 403: Number Of Queue Limit, Trunk Access Code For Mobility Access Mode, Isdn Alternating Routing
CM64 COMMAND CODE TITLE: AUTOMATED ATTENDANT, TENANT NUMBER FOR MUSIC ON HOLD, NUMBER OF QUEUE LIMIT, TRUNK ACCESS CODE FOR MOBILITY ACCESS MODE, ISDN ALTERNATING ROUTING FUNCTION: This command is used to define the answering system of the Automated Attendant feature and assign the Tenant Number for Music on Hold, the Number of Queue Limit, the Trunk access code for Mobility Access mode and the ISDN Alternating Routing.
Page 404 CM64 COMMAND CODE TITLE: AUTOMATED ATTENDANT, TENANT NUMBER FOR MUSIC ON HOLD, NUMBER OF QUEUE LIMIT, TRUNK ACCESS CODE FOR MOBILITY ACCESS MODE, ISDN ALTERNATING ROUTING : Default SETTING DATA RELATED TENANT COMMAND MEANING DATA MEANING Tenant Number for Music 00-63 External Hold Tone Source CM48 Y=0...
Page 405 CM64 COMMAND CODE TITLE: AUTOMATED ATTENDANT, TENANT NUMBER FOR MUSIC ON HOLD, NUMBER OF QUEUE LIMIT, TRUNK ACCESS CODE FOR MOBILITY ACCESS MODE, ISDN ALTERNATING ROUTING : Default SETTING DATA RELATED TENANT COMMAND MEANING DATA MEANING Trunk access code for 00-63 X-XXXX Trunk Access Code...
Page 406 CM65 COMMAND CODE TITLE: SERVICES ON TENANT BASIS FUNCTION: This command is used to define the features available in each tenant. PRECAUTION: None ASSIGNMENT PROCEDURE: TENANT NUMBER DATA 65YY + DE (2 digits) (1 digit) DATA TABLE: : Default SETTING DATA RELATED TENANT COMMAND...
Page 407 CM65 COMMAND CODE TITLE: SERVICES ON TENANT BASIS : Default SETTING DATA RELATED TENANT COMMAND MEANING DATA MEANING RR sending priority when 00-63 Send RR signal after receiving OAI SCF SMFN Send RR signal before SMFN Day/Night Mode Two kinds of mode (Day Mode, Night Mode) Four kinds of mode (Day Mode, Night Mode,...
Page 408 CM65 COMMAND CODE TITLE: SERVICES ON TENANT BASIS : Default SETTING DATA RELATED TENANT COMMAND MEANING DATA MEANING Call Forwarding type 00-63 Split Call Forwarding-All CM08>608 when a C.O. incoming Calls/Busy Line/No CME6 Y=04, 05 call is terminated via Answer CM78 CCIS Call Forwarding-All Calls/...
Page 409 CM65 COMMAND CODE TITLE: SERVICES ON TENANT BASIS : Default SETTING DATA RELATED TENANT COMMAND MEANING DATA MEANING Adding the held call on 00-63 Allow CM15 Y=063 Multiline Terminal as a Not allowed third party of Three-Way Calling (Conference [Three/Four Party]) by CNF and LINE key oper- ation NOTE...
Page 410 CM67 COMMAND CODE TITLE: LOCATION DATA ASSIGNMENT FUNCTION: This command is used to assign the location data to the location number set by CM12 Y=39/50 (Peer- to-Peer connection by IP Station), CM8A Y=5000-5255: 173 (Peer-to-Peer connection via CCIS). The location number is used for administration of the location via IP network and can be assigned to each connection type or each location which is divided according to the network traffic.
Page 411 CM67 COMMAND CODE TITLE: LOCATION DATA ASSIGNMENT DATA TABLE: Y=00-08 : Default 1ST DATA 2ND DATA RELATED COMMAND MEANING DATA MEANING DATA MEANING CODEC list XX ZZ XX: Location Programmable CODEC List 0 CM42 between locations number (As per CM42>100-103, CM12 Y=39/50 (00-63) 110-113)
Page 412 CM67 COMMAND CODE TITLE: LOCATION DATA ASSIGNMENT 1ST DATA 2ND DATA RELATED COMMAND MEANING DATA MEANING DATA MEANING NOTE 3: The table below shows the default setting of the CODEC List. Priority CODEC Type Payload Size G.711* 40 ms G.729a 40 ms G.723.1 30 ms...
Page 413 CM67 COMMAND CODE TITLE: LOCATION DATA ASSIGNMENT : Default 1ST DATA 2ND DATA RELATED COMMAND MEANING DATA MEANING DATA MEANING Type of Service XX ZZ XX: Location X: PRECEDENCE 0-7 CM12 Y=39/50 (TOS) field Prece- number for control packet CM8A Y=5000- dence for IP Sta- (00-63) Z : PRECEDENCE 0-7...
Page 414 CM67 COMMAND CODE TITLE: LOCATION DATA ASSIGNMENT : Default 1ST DATA 2ND DATA RELATED COMMAND MEANING DATA MEANING DATA MEANING PAD data between XX ZZ XX: Location TT RR TT (Transmitter PAD): CM12 Y=39/50 +: Gain locations number CM8A Y=5000- (00-63) –: Loss 5255: 173...
Page 415 CM67 COMMAND CODE TITLE: LOCATION DATA ASSIGNMENT : Default 1ST DATA 2ND DATA RELATED COMMAND MEANING DATA MEANING DATA MEANING Echo Canceller XX ZZ XX: Location Echo Canceller OFF CM12 Y=39/50 between locations number Echo Canceller ON CM8A Y=5000- (00-63) NONE Echo Canceller ON 5255: 173...
Page 416 CM67 COMMAND CODE TITLE: LOCATION DATA ASSIGNMENT : Default 1ST DATA 2ND DATA RELATED COMMAND MEANING DATA MEANING DATA MEANING Diffserv Code XX ZZ XX: Location XX ZZ XX: 00-FE: DSCP of CM12 Y=39/50 Point (DSCP) of number control packet CM8A Y=5000- control packet and (00-63)
Page 417 CM67 COMMAND CODE TITLE: LOCATION DATA ASSIGNMENT Y=10-24 : Default 1ST DATA 2ND DATA RELATED COMMAND MEANING DATA MEANING DATA MEANING Time Zone setting Location number XXXXX Time Zone CM02 of each location (see the table below) NONE No Time Zone 2nd Data Time Zone A2345...
Page 418 CM67 COMMAND CODE TITLE: LOCATION DATA ASSIGNMENT : Default 1ST DATA 2ND DATA RELATED COMMAND MEANING DATA MEANING DATA MEANING Type of tone for Location number Japan CM12 Y=39/50 each area/country North America for each location Australia A-law countries Hong Kong Malaysia Singapore Mexico...
Page 419 CM67 COMMAND CODE TITLE: LOCATION DATA ASSIGNMENT : Default 1ST DATA 2ND DATA RELATED COMMAND MEANING DATA MEANING DATA MEANING Type of Service Location number PRECEDENCE 0 CM12 Y=39/50 (TOS) field Prece- PRECEDENCE 1 CMAD Y=29 dence of control PRECEDENCE 2 packet for IP Sta- PRECEDENCE 3 tion for each loca-...
Page 420 CM67 COMMAND CODE TITLE: LOCATION DATA ASSIGNMENT : Default 1ST DATA 2ND DATA RELATED COMMAND MEANING DATA MEANING DATA MEANING Programmable list FAX Protocol Pat- Not detect the FAX pro- tern No. tocol NOTE Programmable list G.711 µ-law G.711 A-law Programmable list G.726 NONE...
Page 421 CM67 COMMAND CODE TITLE: LOCATION DATA ASSIGNMENT Y=30, 31 : Default 1ST DATA 2ND DATA RELATED COMMAND MEANING DATA MEANING DATA MEANING Daylight Saving Location number To operate with Daylight CM67 Y=10 time setting of each Saving time (+1 hour) CM0B Y=1XX>...
Page 422 CM67 COMMAND CODE TITLE: LOCATION DATA ASSIGNMENT Y=90-92 : Default 1ST DATA 2ND DATA RELATED COMMAND MEANING DATA MEANING DATA MEANING Limit bandwidth XX ZZ XX: Location 00000 0 Kbps CM12 Y=39/50 between locations number CM8A (00-63) 65534 65534 Kbps Y=5000-5255: ZZ : Location NONE...
Page 423 CM71 COMMAND CODE TITLE: MEMORY ALLOCATION FOR SYSTEM SPEED DIALING FUNCTION: This command is used to allocate memory area for System Speed Dialing to tenants, attendants, Hot Line-Outside and Delayed Hotline-Outside station. PRECAUTION: System Speed Dialing has 300 memory locations system-wide; this is referred to as a “Memory Block”...
Page 424 CM71 COMMAND CODE TITLE: MEMORY ALLOCATION FOR SYSTEM SPEED DIALING Limitation on Memory Slot Allocations • In a single-tenant system, Tenant 00 can be assigned a maximum of 300 memory slots. • Per Tenant: Maximum of 300 memory slots • For Hot Line-Outside/Delayed Hotline-Outside call: Maximum of 100 memory slots (maximum number of Hot Lines/Delayed Hotlines) •...
Page 425 CM71 COMMAND CODE TITLE: MEMORY ALLOCATION FOR SYSTEM SPEED DIALING ASSIGNMENT PROCEDURE: KIND OF DATA + 71 + CALLING PARTY (6 digits) (2 digits) DATA TABLE: : Default KIND OF CALLING PARTY SETTING DATA MEANING DATA MEANING Tenant 00 XXX YYY XXX: Starting Memory Slot number in Block: 000-299 Tenant 63...
Page 426 CM72 COMMAND CODE TITLE: STORED NUMBER FOR SYSTEM SPEED DIALING FUNCTION: This command is used to enter the stored number or character for System Speed Dialing feature into the memory allocated with CM71. PRECAUTION: When displaying the data, the access code corresponding to the Memory Slot number is indicated by the very first , and the stored number is indicated by the next .
Page 427 CM72 COMMAND CODE TITLE: STORED NUMBER FOR SYSTEM SPEED DIALING DATA TABLE: : Default 1ST DATA 2ND DATA DATA MEANING DATA MEANING 000-299 Memory Slot number XXXX YY...Y XXXX: Access Code (Maximum 4 digits) : Separator Mark YY...Y : Called Party Number (Maximum 26 digits) X-XXXXXXXX Station Number (Maximum 8 dig-...
Page 428 CM73 COMMAND CODE TITLE: MEMORY ALLOCATION FOR STATION SPEED DIALING FUNCTION: This command is used to allocate memory areas for Station Speed Dialing to individual stations. PRECAUTION: The allowed number of 10-Slot Memory Blocks per station number ranges from 1 to 10. ASSIGNMENT PROCEDURE: STATION NUMBER DATA...
Page 429 CM73 COMMAND CODE TITLE: MEMORY ALLOCATION FOR STATION SPEED DIALING NOTE 3: An entry of “0342106” would allocate six (6) 10-Slot Memory Blocks, which would accom- modate sixty (60) Station Speed Dialing numbers. 1000- Slot Memory Block number 03 would be used, starting at 10-Slot Memory Block number 42, and ending at 10-Slot Memory Block number 47.
Page 430 CM73 COMMAND CODE TITLE: MEMORY ALLOCATION FOR STATION SPEED DIALING Example: If the quantity of Speed Dial numbers is 10 for Station Number 300, 20 for Station Number 301, and 30 for Station Number 302, the memory areas assignment is as follows. Memory Start Block Station 1000-Slot Memory...
Page 431 CM73 COMMAND CODE TITLE: MEMORY ALLOCATION FOR STATION SPEED DIALING A memory area allocated by CM73 can be shared with several stations. Also, in the stations, which station can assign or change the data can be determined. Example: Station Number Assigned data Facility for Programming 0000003...
Page 432 CM74 COMMAND CODE TITLE: STORED NUMBER FOR STATION SPEED DIALING FUNCTION: This command is used to enter the stored number for Station Speed Dialing feature into the memory al- located with CM73. PRECAUTION: Data can only be changed when the access code is displayed. Enter the data in the following order; the new access code, comma, the called number, and .
Page 433 CM74 COMMAND CODE TITLE: STORED NUMBER FOR STATION SPEED DIALING DATA TABLE: : Default 1ST DATA 2ND DATA DATA MEANING DATA MEANING XX YY Z XX: 1000-Slot Memory Block XX...X YY...Y XX...X: Access Code number (00-19) (Maximum 4 digits) YY: 10-Slot Memory Block : Separator Mark number (00-99) YY...Y : Called Party Number...
Page 434 CM74 COMMAND CODE TITLE: STORED NUMBER FOR STATION SPEED DIALING : Default 1ST DATA 2ND DATA DATA MEANING DATA MEANING XX YY Z XX: 1000-Slot Memory Block XXX…X Calling Party Name Character [8300R2] number (00-19) Code (Maximum 32 digits: 16 YY: 10-Slot Memory Block characters) (for Russian) number (00-99)
Page 435 CM76 COMMAND CODE TITLE: DIGIT CONVERSION ON DID CALL FUNCTION: This command is used to assign the data required for interpreting the dialed-in digits. PRECAUTION: Digit Conversion on DID call is available when CM35 Y=018 is set to 0. The first digit in the first data field must be assigned, in CM20 Y=0-3, as a station number 801- 808 and 811-818.
Page 436 CM76 COMMAND CODE TITLE: DIGIT CONVERSION ON DID CALL : Default 2ND DATA 1ST DATA REMARKS MEANING DATA MEANING For Day Mode 000-999: Station number to be terminated CM10 Number Conver- NOTE 1 CM11 For Night Mode sion Block No. XXXXXXXX assigned by Change terminating system to:...
Page 437 CM76 COMMAND CODE TITLE: DIGIT CONVERSION ON DID CALL : Default 2ND DATA 1ST DATA REMARKS MEANING DATA MEANING Terminating 000-999: Trunk Tenant 00 CM35 Trunk Tenant dur- Number Conver- Y=018 ing Day Mode sion Block No. Trunk Tenant 63 (for TAS) assigned by NONE...
Page 438 CM76 COMMAND CODE TITLE: DIGIT CONVERSION ON DID CALL : Default 2ND DATA 1ST DATA REMARKS MEANING DATA MEANING Calling party 000-999: Available CM15 Y=134 number is used as Number Conver- Not available CM2A Y=15, the ID Code for sion Block No. 16, A0 Remote Access to assigned by...
Page 439 CM76 COMMAND CODE TITLE: DIGIT CONVERSION ON DID CALL : Default 2ND DATA 1ST DATA REMARKS MEANING DATA MEANING Terminating Sta- 000-999: Station Tenant 00 tion Tenant for Number Conver- each DID number sion Block No. Station Tenant 63 during Mode B assigned by NONE Trunk Tenant...
Page 440 CM76 COMMAND CODE TITLE: DIGIT CONVERSION ON DID CALL : Default 2ND DATA 1ST DATA REMARKS MEANING DATA MEANING Multiline Termi- 000-999: Ringer Tone Pattern 0 CM35 nal Ringer Tone Number Conver- Ringer Tone Pattern 1 Y=034, 164 Pattern on DID sion Block No.
Page 441 CM76 COMMAND CODE TITLE: DIGIT CONVERSION ON DID CALL : Default 2ND DATA 1ST DATA REMARKS MEANING DATA MEANING Whether the call 000-999: Specified when reason of the incom- CM76 Y=34 terminating Number Conver- ing calls with no CLI is “Privacy” method is speci- sion Block No.
Page 442 CM76 COMMAND CODE TITLE: DIGIT CONVERSION ON DID CALL : Default 2ND DATA 1ST DATA REMARKS MEANING DATA MEANING Specification of 000-999: To transfer to the VRS/another sta- CM51 Y=33 the call terminat- Number Conver- tion/Attendant Console (assigned by CM76 Y=35, ing method for sion Block No.
Page 443 CM76 COMMAND CODE TITLE: DIGIT CONVERSION ON DID CALL : Default 2ND DATA 1ST DATA REMARKS MEANING DATA MEANING Interval of SLT/ 000-999: Ringing NOTE3 CM08>397 Multiline Termi- Number CM08>397 CM76 Y=22, nal ringing tone Conversion Special Ringing 34, 36 for DID incoming Block No.
Page 444 CM76 COMMAND CODE TITLE: DIGIT CONVERSION ON DID CALL : Default 2ND DATA 1ST DATA REMARKS MEANING DATA MEANING Multiline Termi- 000-999: Ringer Tone Pattern 0 CM65 Y=40 nal Ringer Tone Number Conver- Ringer Tone Pattern 1 CM76 Y=23, Pattern for DID sion Block No.
Page 445 CM76 COMMAND CODE TITLE: DIGIT CONVERSION ON DID CALL : Default 2ND DATA 1ST DATA REMARKS MEANING DATA MEANING Registered DID 0000-0999: XXX ZZZZ XXX : Number Conversion Block CM76 Y=00 number display Registered DID No. assigned by CM76 Y=00 number is dis- ZZZZ: DID Number assigned by played from the...
Page 446 CM76 COMMAND CODE TITLE: DIGIT CONVERSION ON DID CALL Data settings for Day/Night/A/B Mode Distinction of tenant An explanation of tenant selection method for Day/Night/A/B Mode change, when DID call ter- minates, is shown below as a tree diagram for system data registration. When station tenant for each DID number is assigned.
Page 447 CM76 COMMAND CODE TITLE: DIGIT CONVERSION ON DID CALL When station tenant for each DID number is not assigned. (CM76 Y=09 is not set) Terminating Trunk Tenant DAY/NIGHT/A/B Mode change CM76 Terminates at station set by Y=01 CM76 Y=01 00~63 Trunk Tenant set by CM76 Y=05 Terminating Trunk...
Page 448 CM77 COMMAND CODE TITLE: STATION/TRUNK ROUTE/CS/ZT/DESKCON NAME ASSIGNMENT FUNCTION: This command is used to assign the name of each station, trunk route, Cell Station (Zone Transceiver) and DESKCON which is displayed on Multiline Terminal or Attendant Console. PRECAUTION: When entering data with characters, the following characters can be registered; Alphabet upper case (A-Z), alphabet lower case (a-z), numeric (0-9), symbol (! “...
Page 449 CM77 COMMAND CODE TITLE: STATION/TRUNK ROUTE/CS/ZT/DESKCON NAME ASSIGNMENT : Default STATION No./TRUNK SETTING DATA ROUTE NAME No./ REMARKS MEANING DATA MEANING CS/ZT No./DESKCON No. Trunk Route Name 00-14, 16-63: Trunk Route XXX...X Character Code CM35 Y=003 assignment with Name number (Maximum 8 digits) character code (for assigned by...
Page 450 CM77 COMMAND CODE TITLE: STATION/TRUNK ROUTE/CS/ZT/DESKCON NAME ASSIGNMENT : Default STATION No./TRUNK SETTING DATA ROUTE NAME No./ REMARKS MEANING DATA MEANING CS/ZT No./DESKCON No. DESKCON Name 0-7: DESKCON number Character assignment with assigned by CM10 (Maximum 16 char- character X..X acters) (for English) NONE...
Page 451 CM77 COMMAND CODE TITLE: STATION/TRUNK ROUTE/CS/ZT/DESKCON NAME ASSIGNMENT Character Code Table for English X: Upper digit Y: Lower digit ” & ’ < ¥ > Example: To set “John”, do the following operation. 3-402 NWA-033623-001 Rev.3.0 91ch3005.fm NOVEMBER/12/2008...
Page 452 CM77 COMMAND CODE TITLE: STATION/TRUNK/CS/ZT/DESKCON NAME ASSIGNMENT Character Code Table for Russian X: Upper digit Y: Lower digit É Þ ü æ “ é Æ â ô ä ö µ à ò ü å û ı ç ù Ë ê ÿ...
Page 453 CM78 COMMAND CODE TITLE: DESTINATION OF SPLIT CALL FORWARDING FUNCTION: This command is used to assign the called number of Split Call Forwarding. PRECAUTION: None ASSIGNMENT PROCEDURE: • To assign destination of Split Call Forwarding 1ST DATA 2ND DATA + DE (3 digits) (1-31 digits) •...
Page 454 CM81 COMMAND CODE TITLE: TOLL RESTRICTION PATTERN ON EACH TRUNK RESTRICTION CLASS FUNCTION: Toll call restriction is controlled by combinations of the toll office code dialed and assigned station trunk restriction class. With respect to toll call restriction, there are eight kinds of trunk restriction classes; Un- restricted, Non-Restricted-1, Non-Restricted-2, Semi-Restricted-1, Semi-Restricted-2, Restricted-1, Re- stricted-2, and Fully Restricted.
Page 455 CM81 COMMAND CODE TITLE: TOLL RESTRICTION PATTERN ON EACH TRUNK RESTRICTION CLASS ASSIGNMENT PROCEDURE: The following command format is used to change the standard assignment data above to meet local re- quirements: TRUNK RESTRICTION DATA ST + 81YY CLASS (1 digit) (1 digit) DATA TABLE: TRUNK RESTRICTION...
Page 456 CM81 COMMAND CODE TITLE: TOLL RESTRICTION PATTERN ON EACH TRUNK RESTRICTION CLASS Examples: The following examples are typical installations within Melbourne, Australia. Unrestricted : No restrictions Non-Restricted-1 : 115, 116, 118, 001 and 010 codes are restricted. Non-Restricted-2 : 115, 116, 118, 02, 04, 06-09, 001-007, 009-011, 014, 016, 018, 019 and 054 codes are restricted.
Page 457 CM85 COMMAND CODE TITLE: MAXIMUM NUMBER OF SENDING DIGITS FUNCTION: This command is used to define the maximum number of digits which can be dialed, after C.O. access, given a specific first digit. PRECAUTION: This command is effective when CM35 Y=076 is assigned. ASSIGNMENT PROCEDURE: MAXIMUM NUMBER AREA/OFFICE CODE...
Page 458 CM85 COMMAND CODE TITLE: MAXIMUM NUMBER OF SENDING DIGITS Example: The example given is typical for Australian applications and more specifically would apply to installations within Melbourne. NUMBER TO BE SENT TO C.O. LINE MAXIMUM NUMBER OF SENDING DIGIT NUMBER TO BE SENT TO C.O. LINE MAXIMUM NUMBER OF SENDING DIGIT NUMBER TO BE SENT TO C.O.
Page 459 CM8A COMMAND CODE TITLE: LCR/TOLL RESTRICTION DEVELOPMENT TABLE FUNCTION: This command is used to define the development tables used for Least Cost Routing (LCR) and Toll Re- striction (TR) features. PRECAUTION: To provide Outgoing Trunk Queuing (Trunk Queuing-Outgoing) in conjunction with Least Cost Rout- ing-3/6 Digit, you must set Route Pattern No.
Page 460 CM8A COMMAND CODE TITLE: TOLL RESTRICTION DEVELOPMENT TABLE DATA TABLE: Toll Restriction Development Table CM35 Y=011, 076) : Default 1ST DATA 2ND DATA MEANING DATA MEANING DATA MEANING 0000 Route Pattern No. 000 TR/LCR Pattern for 6- 00000 XXX 00 digit Toll Restriction XXX: TR Pattern 0255...
Page 461 CM8A COMMAND CODE TITLE: TOLL RESTRICTION DEVELOPMENT TABLE : Default 1ST DATA 2ND DATA MEANING DATA MEANING DATA MEANING 3000 Date Pattern No. 0 Sunday 0000 Route Pattern No. 000 Monday 3003 Date Pattern No. 3 Tuesday 0255 Route Pattern No. 255 Wednesday (CM8A Y=0000-0255) Thursday...
Page 462 CM8A COMMAND CODE TITLE: TOLL RESTRICTION DEVELOPMENT TABLE : Default 1ST DATA 2ND DATA MEANING DATA MEANING DATA MEANING 4000 Area Code Development Area Code 0000 Route Pattern No. 000 Pattern No. 0 (Maximum 8 digits) XX...XX 0255 Route Pattern No. 255 4004 Area Code Development (CM8A Y=0000-0255)
Page 463 CM8A COMMAND CODE TITLE: TOLL RESTRICTION DEVELOPMENT TABLE : Default 1ST DATA 2ND DATA MEANING DATA MEANING DATA MEANING 5000 TR Pattern No. 000 Designation of Trunk Toll Restriction Pattern Restriction Pattern No. No. 00 5255 TR Pattern No. 255 Toll Restriction Pattern No.
Page 464 CM8A COMMAND CODE TITLE: LCR DEVELOPMENT TABLE LCR Development Table : Default 1ST DATA 2ND DATA MEANING DATA MEANING DATA MEANING 0000 Route Pattern No. 000 Designation of next table 0000 Next Pattern No. 000 (Route Pattern No.) 0255 Route Pattern No. 255 0255 Next Pattern No.
Page 465 CM8A COMMAND CODE TITLE: LCR DEVELOPMENT TABLE : Default 1ST DATA 2ND DATA MEANING DATA MEANING DATA MEANING 3000 Date Pattern No. 0 Sunday 0000 Route Pattern No. 000 Monday 3003 Date Pattern No. 3 Tuesday 0255 Route Pattern No. 255 Wednesday (CM8A Y=0000-0255) Thursday...
Page 466 CM8A COMMAND CODE TITLE: LCR DEVELOPMENT TABLE : Default 1ST DATA 2ND DATA MEANING DATA MEANING DATA MEANING 4005 Area Code Development Area Code 3000 Date Pattern No. 0 Pattern No. 5 (Maximum 8 digits) XX...XX 3003 Date Pattern No. 3 4007 Area Code Development (CM8A Y=3000-3003)
Page 467 CM8A COMMAND CODE TITLE: LCR DEVELOPMENT TABLE : Default 1ST DATA 2ND DATA MEANING DATA MEANING DATA MEANING 5000 LCR Pattern No. 000 Designation of Trunk Toll Restriction Pattern Restriction Pattern No. No. 00 5255 LCR Pattern No. 255 Toll Restriction Pattern No.
Page 468 CM8A COMMAND CODE TITLE: LCR DEVELOPMENT TABLE : Default 1ST DATA 2ND DATA MEANING DATA MEANING DATA MEANING 5000 LCR Pattern No. 000 Number of digit to be No digit deletion deleted from Area Code First one digit deletion 5255 LCR Pattern No.
Page 469 CM8A COMMAND CODE TITLE: LCR DEVELOPMENT TABLE : Default 1ST DATA 2ND DATA MEANING DATA MEANING DATA MEANING 5000 LCR Pattern No. 000 Type of Number of Unknown Called Party Number International number 5255 LCR Pattern No. 255 (for E.164) National number Not used Subscriber number...
Page 470 CM8A COMMAND CODE TITLE: LCR DEVELOPMENT TABLE : Default 1ST DATA 2ND DATA MEANING DATA MEANING DATA MEANING 5000 LCR Pattern No. 000 Call by Call Type of Network ID No. Network ID Plan [North America Only] 5255 LCR Pattern No. 255 NONE No data Call by Call...
Page 471 CM8A COMMAND CODE TITLE: LCR DEVELOPMENT TABLE : Default 1ST DATA 2ND DATA MEANING DATA MEANING DATA MEANING 5000 LCR Pattern No. 000 Call by Call WATS Band Number WATS Band Number 5255 LCR Pattern No. 255 [North America Only] NONE No data Caller ID on outgoing...
Page 472 CM8A COMMAND CODE TITLE: LCR DEVELOPMENT TABLE : Default 1ST DATA 2ND DATA MEANING DATA MEANING DATA MEANING 5000 LCR Pattern No. 000 Release timer for IPT 30 seconds (P2P CCIS) Point-to- 1 minute 5255 LCR Pattern No. 255 Multipoint connection (1 minute increments) 127 minutes NONE...
Page 473 CM8A COMMAND CODE TITLE: LCR DEVELOPMENT TABLE : Default 1ST DATA 2ND DATA MEANING DATA MEANING DATA MEANING 5000 LCR Pattern No. 000 Calling party number sent Calling party number is not from SIP Trunk sent 5255 LCR Pattern No. 255 To send SIP subscriber number assigned by CM12 Y=12/13...
Page 474 CM8A COMMAND CODE TITLE: LCR DEVELOPMENT TABLE : Default 1ST DATA 2ND DATA MEANING DATA MEANING DATA MEANING 8000 6-digit TR No. 00 Office Code (3 digits) Restricted Allowed 8049 6-digit TR No. 49 8050 6-digit Prefix No. 00 Office Code (3 digits) Restricted Allowed 8099...
Page 475 CM90 COMMAND CODE TITLE: MULTILINE TERMINAL/DESKCON/ADD-ON MODULE KEY ASSIGNMENT FUNCTION: This command is used to assign functions to programmable keys on a Multiline Terminal, DESKCON or Add-on Module. PRECAUTION: “My Line” must always be assigned to any key on each Multiline Terminal or Add-on Module. For assignment of a key on the Add-on Module, CM98 data should be assigned before data assignment of CM90.
Page 476 CM90 COMMAND CODE TITLE: MULTILINE TERMINAL KEY ASSIGNMENT ASSIGNMENT PROCEDURE: Multiline Terminal MY LINE DATA + 90YY + NUMBER NUMBER (1-8 digits) (1-8 digits) (01-24, 90-99) DATA + 9010 + + DE NUMBER (1-8 digits) (01-24, 90-99) 3-427 NWA-033623-001 Rev.3.0 91ch3006.fm NOVEMBER/12/2008...
Page 477 CM90 COMMAND CODE TITLE: MULTILINE TERMINAL KEY ASSIGNMENT DATA TABLE: Multiline Terminal SETTING DATA RELATED COMMAND MEANING DATA MEANING Setting of Functions Station number CM10 • My Line number (FX-FXXXXXXXX) CM11 XXXXXXXX • Multiline number (Ordinary Station) • Multiline number (assigned by CM11) X: 0-9, A (*), B (#) A000...
Page 478 CM90 COMMAND CODE TITLE: MULTILINE TERMINAL KEY ASSIGNMENT SETTING DATA RELATED COMMAND MEANING DATA MEANING Setting of Functions AA01 Loop Line number for Multiline Terminal CM11 Attendant Position CM15 Y=071 AA05 CM12 Y=03 AA11 AAX Z X: Multiline Terminal Attendant Position AA15 No.
Page 479 CM90 COMMAND CODE TITLE: MULTILINE TERMINAL KEY ASSIGNMENT SETTING DATA RELATED COMMAND MEANING DATA MEANING Setting of Functions F0XXX 018: Call Forwarding-Destination Set CM15 Y=015 (FDDS) 019: Call Forwarding-Destination Cancel (FDDC) 020: Call Pickup-Group (PICK) CM16 021: Call Pickup-Direct (DPICK) CM15 Y=014 022: Do Not Disturb Set/Reset (DND) CM15 Y=019...
Page 480 CM90 COMMAND CODE TITLE: MULTILINE TERMINAL KEY ASSIGNMENT SETTING DATA RELATED COMMAND MEANING DATA MEANING Setting of Functions F0XXX Service access code 040: Message Waiting Lamp Set (MWS) CM15 Y=024 041: Message Waiting Lamp Reset (MWR) 044: ACD/UCD Busy out (UCDB) 046: Call Hold (CHLD) CM15 Y=001 047: TAS Answer A (TASA)
Page 481 CM90 COMMAND CODE TITLE: MULTILINE TERMINAL KEY ASSIGNMENT : Default SETTING DATA RELATED COMMAND MEANING DATA MEANING Setting of Functions F0XXX Service access code A26: LCR Group 0 A27: LCR Group 1 A28: LCR Group 2 A46: Call History screen start Message A47: Call Back to Call History-No Answer/Message Waiting...
Page 482 CM90 COMMAND CODE TITLE: MULTILINE TERMINAL KEY ASSIGNMENT : Default SETTING DATA RELATED COMMAND MEANING DATA MEANING Setting of Functions F0XXX B51: Connection between Soft Phone and NOTE B54: Restriction of additional participants to conference Set/Cancel [8300R2] B56: Mobility Access Mode Set/Cancel CM20 Y=0-3: NOTE A256, A257...
Page 483 CM90 COMMAND CODE TITLE: MULTILINE TERMINAL KEY ASSIGNMENT : Default SETTING DATA RELATED COMMAND MEANING DATA MEANING Speaker Setting of Functions F1XXX 016: (SPKR) 017: (MIC) Use as a one-touch mute key 020: Release key (RLS) 032: OAI Function Key 0 CMD7 Y=0 047: OAI Function Key 15 058: QoS Display on IP Station...
Page 484 CM90 COMMAND CODE TITLE: MULTILINE TERMINAL KEY ASSIGNMENT SETTING DATA RELATED COMMAND MEANING DATA MEANING term Setting of Functions F1XXX 090: Headset/Handset Key For D term NOTE: Series E) Used to switch to headset or back to handset. 091: Record (Voice Mail Live Record) 094: End (Voice Mail Live Record) 098: Voice Mail Key (Destination of CM51 Y=15)
Page 485 CM90 COMMAND CODE TITLE: MULTILINE TERMINAL KEY ASSIGNMENT : Default SETTING DATA RELATED COMMAND MEANING DATA MEANING Setting of Functions F15XX 00: ACD/UCD Group 00 Busy Lamp CM15 Y=049 (UCD00) CM17 Y=1 15: ACD/UCD Group 15 Busy Lamp (UCD15) 99: All Zone Internal Paging CM08>158 CM56 Y=00-07 F16XX...
Page 486 CM90 COMMAND CODE TITLE: MULTILINE TERMINAL KEY ASSIGNMENT : Default SETTING DATA RELATED COMMAND MEANING DATA MEANING Setting of Functions F5000 Call Park-System (CPSY) F5001 Transfer to VMS F5010 Caller ID Display F5011 Call Redirect for transferring to station CM51 Y=22 F5012 Call Redirect for transferring to VMS CM51 Y=18...
Page 487 CM90 COMMAND CODE TITLE: MULTILINE TERMINAL KEY ASSIGNMENT : Default SETTING DATA RELATED COMMAND MEANING DATA MEANING Multiline Terminal ring- Day Mode: No ringing/Night Mode: CM08>577 ing tone by Day Mode/ Ringing Night Mode Day Mode: Ringing/Night Mode: No ringing Day Mode: No ringing/Night Mode: No ringing Day Mode: Ringing/Night Mode: Ringing...
Page 488 CM90 COMMAND CODE TITLE: DESKCON KEY ASSIGNMENT SN716 DESKCON Call Selection/Function Key Assignment: DESKCON DESKCON SETTING + , + + 90YY + NUMBER KEY NUMBER DATA (E000-E007) (01-97) (5 digits) Multi-Function Key Assignment: MULTI- SETTING FUNCTION + , + 90YY EXX Y ST + + DE...
Page 489 CM90 COMMAND CODE TITLE: DESKCON KEY ASSIGNMENT SN716 DESKCON • DESKCON Call Selection Key STANDARD SETTING RELATED FUNCTION REMARKS DATA COMMAND MEANING SETTING Setting of F6000 C.O. Incoming Call 0 (LDN0) LDN0 CM35 Functions Y=015 [8300R2] F6007 C.O. Incoming Call 7 (LDN7) F6010 Call Termination from FX Line 0 CM35...
Page 490 CM90 COMMAND CODE TITLE: DESKCON KEY ASSIGNMENT STANDARD SETTING RELATED FUNCTION REMARKS DATA COMMAND MEANING SETTING Setting of F6054 Priority Call 0 (PRI0) CM15 Functions Y=017 [8300R2] CM08>250, CM20>A088 F6055 Priority Call 1 (PRI1) CM15 Y=018 CM08>251, CM20>A089 F6056 Emergency Call (EMGC) CM20>A094 F6060 Operator Call (ATND)
Page 491 CM90 COMMAND CODE TITLE: DESKCON KEY ASSIGNMENT • DESKCON Function Key STANDARD SETTING RELATED FUNCTION REMARKS DATA COMMAND MEANING SETTING Setting of F6100 Room Cutoff (RC) For Hotel DESKCON NOTE 1: Functions Use the ANSWER key as the SET F6101 Message Waiting (MW) [8300R2] key for Hotel features.
Page 492 CM90 COMMAND CODE TITLE: DESKCON KEY ASSIGNMENT STANDARD SETTING RELATED FUNCTION REMARKS DATA COMMAND MEANING SETTING Setting of F6120 Malicious Call Trace CM15 Functions [Australia Only] Y=211 [8300R2] F6121 Last Number Call (Last Number Redial)-Attendant/Stack Dial-Atten- dant F6122 Select Key of Calling Number Dis- play or Calling Name Display F6123 Transfer to VMS...
Page 493 CM90 COMMAND CODE TITLE: DESKCON KEY ASSIGNMENT STANDARD SETTING RELATED FUNCTION REMARKS DATA COMMAND MEANING SETTING Setting of F1201 Lamp indication when trunks are all Maximum 6 CM30 Y=09 Functions busy in Trunk Group 01 keys per [8300R2] (TGB01) DESKCON NOTE 1 F1262 Lamp indication when trunks are all...
Page 494 CM90 COMMAND CODE TITLE: DESKCON KEY ASSIGNMENT • DESKCON Multi-Function Key No. 01-04 CM60 Y=17 DESKCON SETTING RELATED STATUS MEANING FUNCTION REMARKS DATA COMMAND Idle state F6100 Room Cutoff [8300R2] (RCOF) F6102 Do Not Disturb (DND) F6104 Reset (RESET) F6110 Mode (MODE) F6111 Programming (PROG)
Page 495 CM90 COMMAND CODE TITLE: DESKCON KEY ASSIGNMENT DESKCON SETTING RELATED STATUS MEANING FUNCTION REMARKS DATA COMMAND When the called F6108 Do Not Disturb station is in DND Override (DDOV) [8300R2] When accessing F6100 Room Cutoff For Hotel DESKCON Hotel features (RCOF) [8300R2] NOTE:...
Page 496 CM90 COMMAND CODE TITLE: DESKCON KEY ASSIGNMENT NOTE 4: If no data is set, the Multi-Function keys are automatically set by default as shown below. • Idle State MODE: Mode PROG: Programming 1:23 PM WED 01 OCT 2008 MODE PROG •...
Page 497 CM90 COMMAND CODE TITLE: ADD-ON MODULE KEY ASSIGNMENT Add-On Module MY LINE KEY NUMBER DATA + 90YY + NUMBER (1-8 digits) (30-89) (1-8 digits) KEY NUMBER DATA + 9010 + + DE (1-8 digits) (30-89) SETTING DATA RELATED COMMAND MEANING DATA MEANING Setting of Func-...
Page 498 CM90 COMMAND CODE TITLE: ADD-ON MODULE KEY ASSIGNMENT : Default SETTING DATA RELATED COMMAND MEANING DATA MEANING Setting of Func- B000 Dial Intercom number CM11 tions CM56 Y=12 B900 B001 B901 B024 B924 D000 Trunk number CM10 CM30 Y=18 D511 F11XX CM73 00-99: Station Speed Dialing 00-99...
Page 499 CM93 COMMAND CODE TITLE: PRIME LINE FUNCTION: This command is used to assign the prime line to a station line or a trunk line on a Multiline Terminal. The prime line is the line seized when the Multiline Terminal user goes off-hook or presses the speaker button.
Page 500 CM94 COMMAND CODE TITLE: MULTILINE TERMINAL ONE-TOUCH MEMORY FUNCTION: This command is used to assign memory for the storage of numbers accessed by the one-touch keys on a Multiline Terminal. PRECAUTION: Do not duplicate the same memory area for CM73 and CM94 usually. However, when Dial by Name feature using one-touch keys or BLF on Multiline Terminal line key feature are provided, the same mem- ory areas must be specified by CM73 and CM94.
Page 501 CM96 COMMAND CODE TITLE: DSS CONSOLE NUMBER FUNCTION: This command is used to assign a DSS Console to a station, Multiline Terminal or Attendant Console. PRECAUTION: None ASSIGNMENT PROCEDURE: DSS CONSOLE DATA + 96 + NUMBER (1-8 digits) (2 digits) DATA TABLE: SETTING DATA DSS CONSOLE...
Page 502 CM97 COMMAND CODE TITLE: DSS CONSOLE KEY ASSIGNMENT FUNCTION: This command is used to assign the station numbers and trunk numbers to the keys on each DSS Con- sole. PRECAUTION: None ASSIGNMENT PROCEDURE: DSS CONSOLE DSS KEY DATA + DE NUMBER NUMBER (1-8 digits)
Page 503 CM97 COMMAND CODE TITLE: DSS CONSOLE KEY ASSIGNMENT DATA TABLE: SETTING DATA RELATED CONSOLE COMMAND DATA MEANING NUMBER NUMBER Station number CM10 CM11 XXXXXXXX DXXX Trunk number CM10 CM10> (XXX: 000-511) CM30 E100- Y=02, 03, 18 E131 F13XX CM08>244 00: Day/Night Mode Change by Tenant 00 CM08>245 63: Day/Night Mode Change by Tenant 63 F1052...
Page 504 CM98 COMMAND CODE TITLE: ADD-ON MODULE NUMBER FUNCTION: This command is used to assign the Add-on Module to the My Line number of a Multiline Terminal. PRECAUTION: One Add-on Module number can be assigned for each My Line number of a Multiline Terminal. This command should be performed before the data assignment of CM90.
Page 505 CM9A COMMAND CODE TITLE: MULTILINE TERMINAL SOFT KEY ASSIGNMENT FUNCTION: This command is used to assign functions for the Soft Key on a Multiline Terminal. PRECAUTION: When entering data with characters, the following characters can be registered; Alphabet upper case (A-Z), alphabet lower case (a-z), numeric (0-9), symbol (! “ # $ % & ’ ( ) + , ; < = >...
Page 506 CM9A COMMAND CODE TITLE: MULTILINE TERMINAL SOFT KEY ASSIGNMENT DATA TABLE: : Default 1ST DATA 2ND DATA MEANING DATA MEANING DATA MEANING Setting of Soft aa bb aa : Status Number (00-15) F5002 Scroll key to change the Key function 00: Idle State Soft key indication for each Pat-...
Page 507 CM9A COMMAND CODE TITLE: MULTILINE TERMINAL SOFT KEY ASSIGNMENT : Default 1ST DATA 2ND DATA MEANING DATA MEANING DATA MEANING Setting of Soft aa bb aa : Status Number (00-15) XX...XXX Soft Key name indicated Key name for 00: Idle State on LCD each Pattern 01: During dialing...
Page 508 CM9A COMMAND CODE TITLE: MULTILINE TERMINAL SOFT KEY ASSIGNMENT : Default 1ST DATA 2ND DATA MEANING DATA MEANING DATA MEANING Setting of Soft aa bb aa : Status Number (00-15) X...XXXX Soft Key name indicated Key name for 00: Idle State on LCD each Pattern 01: During dialing...
Page 509 CM9A COMMAND CODE TITLE: MULTILINE TERMINAL SOFT KEY ASSIGNMENT Default Data of CM9A (Pattern No. 3) 1ST DATA of 2ND DATA INDICATION STATUS MEANING Y=03 of Y=03 (Y=13) 0000 Idle F1017 MIC ON/OFF 0001 F5014 Dial By Name for System SYS.
Page 510 CM9A COMMAND CODE TITLE: MULTILINE TERMINAL SOFT KEY ASSIGNMENT Default Data of CM9A (Pattern No. 3) 1ST DATA of 2ND DATA INDICATION STATUS MEANING Y=03 of Y=03 (Y=13) 0600 When called party is F0004 Call Back Set busy (Holding no call) 0601 F0A25 Call Waiting Set...
Page 511 CM9B COMMAND CODE TITLE: EVENT OCCURRENCE NOTICE BUTTON ASSIGNMENT FUNCTION: This command is used to provide the event occurrence notice button. When the offices with CCIS via IPT (P2P CCIS) connection SIP trunk connection are disconnected due to a fault occurrence, the link down can be notified to the Multiline Terminals that are connected to the offices.
Page 512 CM9C COMMAND CODE TITLE: DESI-LESS LCD FUNCTION: This command is used to set characters displayed on DESI-less LCD of DT300/DT700 Series. [8300R2] PRECAUTION: None ASSIGNMENT PROCEDURE: BLOCK NUMBER DATA + 9CYY + + DE (1-16 digits) (2 digits) DATA TABLE: : Default 1ST DATA SETTING DATA...
Page 513 CMA7 COMMAND CODE TITLE: CCIS CHANNEL DATA/IP TRUNK DATA/SIP TRUNK DATA FUNCTION: This command is used to assign the various data to each Common Channel Handler (CCH), IP Trunk and SIP Trunk provided. PRECAUTION: When setting the IPT (P2P CCIS) No. with this command, be sure to set the first data to “00”. ASSIGNMENT PROCEDURE: DATA + DE...
Page 514 CMA7 COMMAND CODE TITLE: CCIS CHANNEL DATA/IP TRUNK DATA/SIP TRUNK DATA : Default SETTING DATA RELATED COMMAND MEANING DATA MEANING Centralized Billing destination 00001 Point Code of Center Billing Office 16367 NONE No data Centralized Fault Reporting destina- 00001 Point Code of Centralized Fault tion Reporting Office 16367...
Page 515 CMA7 COMMAND CODE TITLE: CCIS CHANNEL DATA/IP TRUNK DATA/SIP TRUNK DATA : Default SETTING DATA RELATED COMMAND MEANING DATA MEANING TOS field Precedence for IPT (P2P PRECEDENCE 0 CM35 Y=134 CCIS) control packet CMA7 Y=71 TOS: Type of Service PRECEDENCE 7 NOTE: This data setting is ineffec- PRECEDENCE 0...
Page 516 CMA7 COMMAND CODE TITLE: CCIS CHANNEL DATA/IP TRUNK DATA/SIP TRUNK DATA : Default SETTING DATA RELATED COMMAND MEANING DATA MEANING Baud rate for Common Signaling 64 Kbps Channel 56 Kbps 48 Kbps (1) 48 Kbps (2) 64 Kbps 3-467 NWA-033623-001 Rev.3.0 91ch3007.fm JULY/18/2008...
Page 517 CMA8 COMMAND CODE TITLE: CCIS/IP/SIP ROUTING LABEL ASSIGNMENT FUNCTION: This command is used to assign a destination office for a message to be transferred (e.g. service infor- mation) and the Common Channel Handler (CCH), IP trunk and SIP trunk which accommodate the mes- sage.
Page 518 CMA9 COMMAND CODE TITLE: BLADE RESET ISDN (PRI) D-CHANNEL ASSIGNMENT FUNCTION: This command is used to assign the various data to each D-Channel for ISDN-Primary Rate Interface. PRECAUTION: This command requires the blade reset after data setting. ASSIGNMENT PROCEDURE: D-CHANNEL No. DATA + DE A9YY...
Page 519 CMAA COMMAND CODE TITLE: DTI/BRT/PRT/CCT FUNCTIONS FUNCTION: This command is used to assign the functions to the DTI, BRT, PRT, and CCT blade. PRECAUTION: After setting CMAA Y=00-02, 06, 09, 12, 13, the blade reset is required. ASSIGNMENT PROCEDURE: TRUNK BLADE NUMBER DATA AAYY ST +...
Page 520 CMAA COMMAND CODE TITLE: DTI/BRT/PRT/CCT FUNCTIONS : Default SETTING DATA RELATED COMMAND MEANING DATA MEANING ISDN Protocol Type Australia CM05 for DCH/PRT New Zealand ITU-T (Hong Kong) BLADE RESET AT&T (#4, #5 ESS) NTI (DMS 100, 250) Australia ETSI ETSI VN4 (Chile) ETSI Standard (Brazil, Chile, Columbia, UAE) ITU-T Standard (Thailand)
Page 521 CMAA COMMAND CODE TITLE: DTI/BRT/PRT/CCT FUNCTIONS : Default SETTING DATA RELATED COMMAND MEANING DATA MEANING ISDN Protocol Type Australia CM05 for BRT New Zealand AT&T (#4, #5 ESS) BLADE RESET NTI (DMS 100, 250) Australia ETSI ETSI Standard (Brazil, Columbia, Indonesia, UAE) ITU-T Standard (Thailand) USA NI-1...
Page 522 CMAA COMMAND CODE TITLE: DTI/BRT/PRT/CCT FUNCTIONS : Default SETTING DATA RELATED COMMAND MEANING DATA MEANING Type of PRT/CCT/Q-SIG E1 (2 Mbps) T1 (1.5 Mbps) Providing PRT/BRT blade with To provide CM42>69, 70 ISDN Advice of Charge (AOC) Not provided [UAE Only] A-law/P-law setting of CD-PRTA A-law (PRT) blade...
Page 523 CMAC COMMAND CODE TITLE: ISDN FUNCTIONS RESET FUNCTION: This command is used to assign the functions to the BRT blade. PRECAUTION: This command requires system reset after data setting. ASSIGNMENT PROCEDURE: ISDN ISDN DATA ST + ACYY D-CHANNEL No. MULTIPOINT No. (1-8 digits) (00-31) (0-7)
Page 524 CMAC COMMAND CODE TITLE: ISDN FUNCTIONS RESET : Default SETTING DATA RELATED COMMAND MEANING DATA MEANING Hunting timing when ISDN telephone 1 second CM08>528 break down 6 seconds (1 second increments) NONE No data Type of power supply for ISDN tele- Power supply from the system phone Local power supply...
Page 525 [Latin America Only] 10 mW, –40 dB (Faint) 10 mW, –20 dB (Average) 10 mW, 0 dB (Strong) NOTE: Follow the default setting. When you change the data of CMAD Y=04/05/06/07, contact NEC. Continued on next page 3-476 NWA-033623-001 Rev.3.0 91ch3007.fm...
Page 526 (100ms. increments) information at the synchronous 1400 ms. processing 500 ms. [For PHS] [8300R2] NOTE: Follow the default setting. When you change the data of CMAD Y=04/05/06/07, contact NEC. Continued on next page 3-477 NWA-033623-001 Rev.3.0 91ch3007.fm NOVEMBER/12/2008...
Page 527 CMAD COMMAND CODE TITLE: CS/ZT CALLING AREA/PAD DATA ASSIGNMENT : Default SETTING DATA MEANING CS/ZT No. DATA MEANING Number of continuation synchro- 000-127 1 message nous bit off message for judging a 14 messages [For PHS] 4 messages [8300R2] Time limit for receiving the 1.5 seconds LCCH for judging a gap (1.5 seconds increments)
Page 528 CMAE COMMAND CODE TITLE: CS/ZT OPERATION DATA ASSIGNMENT FUNCTION: This command is used to assign the CS/ZT operation data. PRECAUTION: None ASSIGNMENT PROCEDURE: 1ST DATA SETTING DATA + DE AEYY (2 digits) (1-12 digits) DATA TABLE: : Default 1ST DATA SETTING DATA DATA MEANING...
Page 529 CMAE COMMAND CODE TITLE: CS/ZT OPERATION DATA ASSIGNMENT : Default 1ST DATA SETTING DATA DATA MEANING DATA MEANING Nation Code assignment Refer to Technical Information PI-287 Supplement to [For PHS] SV8300 Programming Manual on Country Code Entry. [8300R2] BLADE RESET Nation Code assignment [Latin America Only] BLADE RESET...
Page 530 CMAE COMMAND CODE TITLE: CS/ZT OPERATION DATA ASSIGNMENT : Default 1ST DATA SETTING DATA MEANING DATA MEANING DATA MEANING CS/ZT Operation 00-31 Calling Area No. Crowded Mode Mode Normal Mode BLADE RESET Width of Calling 00-31 Calling Area No. Wide Area Narrow BLADE RESET...
Page 531 CMAE COMMAND CODE TITLE: CS/ZT OPERATION DATA ASSIGNMENT : Default 1ST DATA SETTING DATA MEANING DATA MEANING DATA MEANING Handover Channel slot for Channel Slot [For PHS] handover (for BS31/ No. 00 BS41) NONE No data [8300R2] NOTE 4 BLADE RESET Delay correction BS31 and BS21 are when the other type of...
Page 532 CMAF COMMAND CODE TITLE: VISITOR PS DATA ASSIGNMENT FUNCTION: This command is used to assign the Visitor PS data for Roaming. [8300R2] PRECAUTION: This data setting is valid when DBM is online. This command is effective only for North America/Latin America. ASSIGNMENT PROCEDURE: 1ST DATA 2ND DATA...
Page 533 CMAF COMMAND CODE TITLE: VISITOR PS DATA ASSIGNMENT : Default 1ST DATA 2ND DATA MEANING DATA MEANING DATA MEANING Trunk Route Selection First Selected Route 00-63 Q-931a D-Channel Trunk for location registration Route No. 00-63 of Visitor PS Data clear [For PCS] NONE No data...
Page 534 CMB0 COMMAND CODE TITLE: PEG COUNT FUNCTION: This command allows accumulated data of use for maintenance purposes to be read from the system PEG counter. Data can be cleared after reading. PRECAUTION: When the system is reset, the contents in the memories of the PEG counter are all cleared. ASSIGNMENT PROCEDURE: •...
Page 535 CMB0 COMMAND CODE TITLE: PEG COUNT • To clear each CS/ZT PEG COUNT data 1ST DATA + DE (4 digits) • To clear all CS/ZT PEG COUNT data + DE DE + 9999 • To display 1ST DATA ST + + DE (4 digits) 3-486...
Page 536 CMB0 COMMAND CODE TITLE: PEG COUNT DATA TABLE: TRUNK STATUS DATA SETTING DATA DATA MEANING Number of outgoing trunk seizure-Trunk Route 00-63 Number of tandem connections established Number of times a busy station was encountered Number of all types of calls to Attendant Console [8300R2] Number of connections giving Dial Tone Number of station-to-station connections established...
Page 537 CMB0 COMMAND CODE TITLE: PEG COUNT TRUNK STATUS DATA SETTING DATA DATA MEANING Number of outgoing calls of ISDN Alternative Routing in Remote Unit survival mode Number of Call Completion to Busy Subscriber (CCBS) set [For EU] from calling party Number of Call Completion to Busy Subscriber (CCBS) set [For EU] to called party...
Page 538 CMB0 COMMAND CODE TITLE: PEG COUNT : Default 1ST DATA 2ND DATA DATA MEANING DATA MEANING Setting of PEG COUNT Start MM DD HH mm MM: Month (01-12) Setting of Time DD : Day (01-31) duration for HH : Hour (00-23) Setting of PEG COUNT End measuring mm : Minute (00-59)
Page 539: Traffic Measurement
CMB1 COMMAND CODE TITLE: TRAFFIC MEASUREMENT FUNCTION: This command is used to measure traffic data of outgoing/incoming trunk calls and to display the data on CAT or PCPro. PRECAUTION: None ASSIGNMENT PROCEDURE: 1ST DATA 2ND DATA + DE (1-5 digits) (1-8 digits) DATA TABLE: : Default...
Page 540 CMB1 COMMAND CODE TITLE: TRAFFIC MEASUREMENT : Default 1ST DATA 2ND DATA MEANING DATA MEANING DATA MEANING Setting of traffic Display data for Traf- Before the traffic measurement condition fic Measurement measurement During the traffic measurement Completed the traffic measurement Continued on next page 3-491 NWA-033623-001 Rev.3.0...
Page 541 CMB1 COMMAND CODE TITLE: TRAFFIC MEASUREMENT 1ST DATA 2ND DATA TRAFFIC MEANING DATA MEANING MEANING DATA Display incoming trunk XXXZ XXX: Trunk No. (000-511) XXXX Incoming trunk traffic data traffic data : Record No. (0-6) (4 digits) X.XXX erl (Ex.) 0125 o 0.125 erl Display outgoing trunk XXXZ XXX: Trunk No.
Page 542 CMB1 COMMAND CODE TITLE: TRAFFIC MEASUREMENT : Default 1ST DATA 2ND DATA MEANING DATA MEANING DATA MEANING Setting of traffic mea- Traffic Measurement No Measurement surement for CS/ZT Mode of CS/ZT Hourly Measurement Setting Start Time for MMDDHH MM: Month (01-12) Traffic Measurement DD : Day (01-31) of CS/ZT...
Page 543 CMB1 COMMAND CODE TITLE: TRAFFIC MEASUREMENT 2ND DATA 1ST DATA TRAFFIC MEANING DATA MEANING MEANING DATA Display traffic data of XXXZZ XXX: CS/ZT No. (000-127) XXXX Traffic data X.XXX erl CS/ZT ZZ : Time Zone No. (00-24) (4 digits) (Ex.) 1223o 1.223 erl NOTE 1: Meaning of the 1st data and 2nd data is as follows.
Page 544 CMB3 COMMAND CODE TITLE: UCD PEG COUNT FUNCTION: This command allows accumulated traffic data related to the UCD Group to be read from the system. PRECAUTION: None ASSIGNMENT PROCEDURE: • To display DATA ST + + DE (1-8 digits) • To clear individual data TRUNK STATUS + DE DATA...
Page 545 CMB3 COMMAND CODE TITLE: UCD PEG COUNT DATA TABLE: SETTING DATA TRUNK STATUS MEANING DATA MEANING DATA Number of answered calls on UCD sta- UCD Station Number tion CM17 Y=0 XXXXXXXX Number of incoming calls to UCD UCD Group 00 Group UCD Group 15 Number of call waiting calls for prede-...
Page 546 CMB4 COMMAND CODE TITLE: PEG COUNT OF IP NETWORK FUNCTION: This command allows accumulated traffic data for Bandwidth Control between location groups on IP network to be read from the system PEG counter. Data can be cleared after reading. PRECAUTION: NONE ASSIGNMENT PROCEDURE: •...
Page 547 CMB4 COMMAND CODE TITLE: PEG COUNT OF IP NETWORK DATA TABLE: 1ST DATA 2ND DATA RELATED COMMAND MEANING DATA MEANING DATA MEANING CM67 Number of times that XXZZ XX: Location 00000 Counter data display traffic exceeded the number of NOTE 1 limit bandwidth group to 49999...
Page 548 CMBA COMMAND CODE TITLE: SIP PROFILE DATA FUNCTION: This command is used to assign the various profile data for SIP Trunk. PRECAUTION: Profile No. for control packet is assigned by CMA7 Y=71. When entering data with characters, the following characters can be registered; Alphabet upper case (A-Z), alphabet lower case (a-z), numeric (0-9), symbol (! “...
Page 549 CMBA COMMAND CODE TITLE: SIP PROFILE DATA : Default 1ST DATA 2ND DATA RELATED COMMAND MEANING DATA MEANING DATA MEANING TOS/Diffserv Prece- Profile number TOS/Diffserv Prece- CM35 Y=161 dence for SIP trunk for control dence CMA7 Y=71 control packet packet CMBA Y=04 NONE No data...
Page 550 CMBA COMMAND CODE TITLE: SIP PROFILE DATA : Default 1ST DATA 2ND DATA RELATED COMMAND MEANING DATA MEANING DATA MEANING SIP server Port number Profile number 00000 SIP server Port num- CMA7 Y=71 for control packet RESET 65534 NONE No data NOTE: The port number of SIP server is 05060 in general.
Page 551 CMBA COMMAND CODE TITLE: SIP PROFILE DATA : Default 1ST DATA 2ND DATA RELATED COMMAND MEANING DATA MEANING DATA MEANING Registration number Profile number Provide registration CM12 Y=12, [representative number] for control packet number (representa- (Change the calling tive number) set by CMA7 Y=71 number to Registration CMBA Y=32...
Page 552 CMBA COMMAND CODE TITLE: SIP PROFILE DATA : Default 1ST DATA 2ND DATA RELATED COMMAND MEANING DATA MEANING DATA MEANING Setting of SIP AoR Profile number XXX...X SIP AoR user name CMA7 Y=71 user name with charac- for control packet (Maximum 32 charac- ters) NONE...
Page 553 CMBA COMMAND CODE TITLE: SIP PROFILE DATA Y=52-99 : Default 1ST DATA 2ND DATA RELATED COMMAND MEANING DATA MEANING DATA MEANING DTMF out-band mode Profile number Out-band mode (with CMA7 Y=71 for SIP trunk for control packet RFC2833) NONE In-band mode (Voice pass through) Setting of SIP AoR XXX...X...
Page 554 CMBA COMMAND CODE TITLE: SIP PROFILE DATA : Default 1ST DATA 2ND DATA RELATED COMMAND MEANING DATA MEANING DATA MEANING SIP trunk registration Profile number To register the time CMA7 Y=71 method to the SIP for control packet set by CMBA Y=71 CMBA Y=71 server To register no limita-...
Page 555 CMBA COMMAND CODE TITLE: SIP PROFILE DATA : Default 1ST DATA 2ND DATA RELATED COMMAND MEANING DATA MEANING DATA MEANING Setting of Authentica- Profile number XXX...X User name CMA7 Y=71 tion user name when for control packet (24 digits, 12 charac- CMBA Y=72, registering to/sending ters fixed)
Page 556 CMBA COMMAND CODE TITLE: SIP PROFILE DATA : Default 1ST DATA 2ND DATA RELATED COMMAND MEANING DATA MEANING DATA MEANING Setting of SIP trunk Profile number XXX...X Domain name CMA7 Y=71 domain name for SIP- for control packet (24 digits, 12 charac- CMBA Y=76, URI with character ters fixed)
Page 557 CMBA COMMAND CODE TITLE: SIP PROFILE DATA : Default 1ST DATA 2ND DATA RELATED COMMAND MEANING DATA MEANING DATA MEANING Session Timer provid- Profile number Not provided CMA7 Y=71 for control packet To provide CMBA Y=29, 56, 88 Identity header of SIP P-Asserted-Identity CMA7 Y=71 Trunk...
Page 558 CMBA COMMAND CODE TITLE: SIP PROFILE DATA : Default 1ST DATA 2ND DATA RELATED COMMAND MEANING DATA MEANING DATA MEANING Setting of the display Profile number Display name: CMA7 Y=71 name/user name for for control packet SIP AoR User CMBA From Header Description following Y=44-47, 54...
Page 559 CMBA COMMAND CODE TITLE: SIP PROFILE DATA : Default 1ST DATA 2ND DATA RELATED COMMAND MEANING DATA MEANING DATA MEANING Setting of the Fully Profile number XXX...X Domain name CMA7 Y=71 Qualified Domain for control packet (24 digits, 12 charac- CMBA Y=93, Name (FQDN) for SIP ters fixed)
Page 560 CMBA COMMAND CODE TITLE: SIP PROFILE DATA : Default 1ST DATA 2ND DATA RELATED COMMAND MEANING DATA MEANING DATA MEANING Setting of the Fully Profile number XXX...X Domain name CMA7 Y=71 Qualified Domain for control packet (16 digits, 8 charac- CMBA Name (FQDN) for SIP ters fixed)
Page 561 CMBA COMMAND CODE TITLE: SIP PROFILE DATA 1ST DATA 2ND DATA RELATED COMMAND MEANING DATA MEANING DATA MEANING Clearing the cache Profile number DNS cache table CMA7 Y=71 table for control packet clearance NOTE: The IP Addresses which were cached for the second data are displayed when the IP Addresses were cached on DNS cache table.
Page 562 CMBA COMMAND CODE TITLE: SIP PROFILE DATA Y=100-110 : Default 1ST DATA 2ND DATA RELATED COMMAND MEANING DATA MEANING DATA MEANING Setting of Authentica- Profile number XXX...X User name CMA7 Y=71 tion user name when for control packet (24 digits, 12 charac- CMBA Y=72, registering to/sending ters fixed)
Page 563 CMBA COMMAND CODE TITLE: SIP PROFILE DATA : Default 1ST DATA 2ND DATA RELATED COMMAND MEANING DATA MEANING DATA MEANING Setting of Authentica- Profile number XXX...X Password CMA7 Y=71 tion password when for control packet (16 digits, 8 charac- CMBA Y=74, registering to/sending ters fixed) 75, 102...
Page 564 CMD7 COMMAND CODE TITLE: OAI CONTROL DATA FUNCTION: This command is used to assign the data to control the OAI facility. PRECAUTION: When you need to assign the port number of the PBX for OAI, on your computer, assign the number “1024/1025/1039/60030”.
Page 565 CMD7 COMMAND CODE TITLE: OAI CONTROL DATA : Default 1ST DATA 2ND DATA MEANING DATA MEANING DATA MEANING Multi-Connection Message number 1000 Voice Response System Announcement service (Fixed) (Fixed) number for MSF NONE No data Waiting timer for RR sig- Setting Timer 8 seconds nal after starting up MSF/...
Page 566 CMD7 COMMAND CODE TITLE: OAI CONTROL DATA : Default 1ST DATA 2ND DATA MEANING DATA MEANING DATA MEANING Chime from Multiline F1032 OAI Function Key No. 0 Not sent Terminal when receiving To send RR signal of MSF/TMF F1047 OAI Function Key No. 15 Chime from Multiline Chime before sending terminal No ring...
Page 567 CME0 COMMAND CODE TITLE: RESET FUNCTION: This command allows the maintenance personnel to execute the System Reset, Blade Reset and IPT (P2P CCIS) Reset with the PCPro/CAT. PRECAUTION: If the setting data (Month, Day and Time) is different from the current time of the system clock set by CM02, any request to reset the system is not accepted and “DATA ERROR”...
Page 568 CME0 COMMAND CODE TITLE: RESET NOTE 1: For the Data “MMDDHHmm”, enter the Month, Date, and Time (hour and minute) of the time, as shown below. MM : Month (01 (Jan.)-12 (Dec.)) DD : Date (01-31) HH : Hour (00-23) mm : Minute (00-59) NOTE 2: Set the same Unit No.
Page 569 CME1 COMMAND CODE TITLE: CPU MEMORY CHECK SUM DISPLAY FUNCTION: This command is used to display Check Sum data on CPU memory. This is only for maintenance. PRECAUTION: None ASSIGNMENT PROCEDURE: • To display MEMORY AREA No. ST + + DE (01-11) Check Sum Data: 0000-FFFF is displayed.
Page 570 CME4 COMMAND CODE TITLE: STATION SERVICE STATUS DISPLAY FUNCTION: This command is used for readout the station service status. PRECAUTION: None ASSIGNMENT PROCEDURE: STATION NUMBER ST + E4YY + DE (1-8 digits) DATA TABLE: READOUT DATA RELATED COMMAND MEANING DATA MEANING Readout service status abcdefgh a: Terminal connection status...
Page 571 CME4 COMMAND CODE TITLE: STATION SERVICE STATUS DISPLAY READOUT DATA RELATED COMMAND MEANING DATA MEANING Readout service status abcdefgh g: Logout/Call Forwarding-PS out of cell (zone) A for each station 0 : Not set 1 : Set h: Do Not Disturb 0 : Not set 1 : Set E: Readout error...
Page 572 CME4 COMMAND CODE TITLE: STATION SERVICE STATUS DISPLAY READOUT DATA RELATED COMMAND MEANING DATA MEANING Readout service status ijklmnop n: ACD/UCD Busy Out CM17 Y=0, 2 B for each station 0 : Not set 1 : Set E: Readout error _ : Not registered ACD/UCD group o: Outgoing Call Restriction 0 : Not set...
Page 573 CME5 COMMAND CODE TITLE: STATION, TRUNK LINE MAKE BUSY FUNCTION: This command is used to make busy any station or trunk in the software. PRECAUTION: None ASSIGNMENT PROCEDURE: STATION/TRUNK DATA + E5Y + NUMBER (1 digit) (1-8 digits) DATA TABLE: : Default STATION/TRUNK NUMBER SETTING DATA...
Page 574 CME5 COMMAND CODE TITLE: STATION, TRUNK LINE MAKE BUSY NOTE 1: For a station that is made busy, call termination to the station is restricted, but call origina- tion is available. For extension lines on a Multiline Terminal, My Line and Multiline make busy can be set in- dividually, with the same condition as mentioned above.
Page 575 CME6 COMMAND CODE TITLE: CALL FORWARDING SET/RESET FROM PCPro/CAT FUNCTION: This command is used to set/reset Call Forwarding service to each station from a PCPro/CAT. PRECAUTION: CME6 can be used for any station irrespective of its state. ASSIGNMENT PROCEDURE: STATION No. DESTINATION No.
Page 576 CME6 COMMAND CODE TITLE: CALL FORWARDING SET/RESET FROM PCPro/CAT : Default MEANING DESTINATION Call Forwarding-PS Out of Cell • Destination=Extension; (Zone) X-XXXXXXXX: Station No. (1-8 digits) Call Forwarding-Logout (IP Station) • Destination=Outside party; X-XXXX + + YY...YY X-XXXX: Outgoing Trunk Access Code (1-4 digits) : Separate Mark YY...YY : Called No.
Page 577 CME7 COMMAND CODE TITLE: PASSWORD LEVEL FUNCTION: This command is used to specify the accessible commands for each Password Level. PRECAUTION: None ASSIGNMENT PROCEDURE: COMMAND CODE DATA E7YY + DE (1-2 digits) (1 digit) DATA TABLE: : Default COMMAND CODE SETTING DATA PASSWORD LEVEL Password Level 0-6...
Page 578 CME8 COMMAND CODE TITLE: UPDATING OF ACCESS BLADE FIRMWARE FUNCTION: This command is used to update the Access blade (Line/Trunk blades) firmware by PCPro/CAT opera- tion. NOTE: The access blade firmware is supplied with the basic software of the CPU. Therefore, when executing the firmware update, execute the firmware update by this command after the update of the basic software is completed.
Page 579 CME8 COMMAND CODE TITLE: UPDATING OF ACCESS BLADE FIRMWARE The download status of the firmware can be confirmed by the following methods. CONFIRMATION METHOD DOWNLOAD STATUS BLADE LED CME8 Y=2 CME8 Y=0 INDICATION Download is completed RUN LED FFFF Firmware version is (normal end) (flash) changed...
Page 580 CME8 COMMAND CODE TITLE: UPDATING OF ACCESS BLADE FIRMWARE DATA TABLE 1ST DATA 2ND DATA RELATED COMMAND MEANING DATA MEANING DATA MEANING Firmware XX ZZ XX: Unit number XX YY ZZ Readout data of firmware CM05 Y=0 download (01-50) when operating ZZ : Slot number XX: Firmware type (Same as (01-18)
Page 581 CME9 COMMAND CODE TITLE: PASSWORD FUNCTION: This command is used to define the Password of each Password Level and the availability of Password Service. PRECAUTION: When programming a Password, the Password for Password Level 7 must be set. If no Password of Password Level 7 is set, the programming of Password Service provision (CME9>9) is restricted with the message “CODE NOT USED”.
Page 582 CMEA COMMAND CODE TITLE: FAULT INFORMATION STORE/DISPLAY FUNCTIONS FUNCTION: This command is used for fault maintenance of the PBX. The functions of this command are outlined below: • Storing fault information into the Fault Store Memory upon occurrence of a fault. •...
Page 583 CMEA COMMAND CODE TITLE: FAULT INFORMATION STORE/DISPLAY FUNCTIONS : Default 1ST DATA 2ND DATA RELATED COMMAND MEANING DATA MEANING DATA MEANING Clear External Clear all of MJ/MN /– – alarms MJ alarms OFF/MN Alarm Kind alarms OFF Clear MJ alarms (MJ/MN) (Display only) Clear MN alarms...
Page 584 CMEA COMMAND CODE TITLE: FAULT INFORMATION STORE/DISPLAY FUNCTIONS : Default 1ST DATA 2ND DATA RELATED COMMAND MEANING DATA MEANING DATA MEANING Fault information Traffic of IP network exceeded External Alarm Kind CM08>450 and external alarm limit bandwidth 0: Fault Memory CM42>01 (Display only) store/No output of...
Page 585 CMEA COMMAND CODE TITLE: FAULT INFORMATION STORE/DISPLAY FUNCTIONS : Default 1ST DATA 2ND DATA RELATED COMMAND MEANING DATA MEANING DATA MEANING Fault information CS/ZT returned to normal con- External Alarm Kind CM08>450 and external alarm dition 0: Fault Memory CM42>01 (Display only) store/No output of LAN application returned to...
Page 586 CMEA COMMAND CODE TITLE: FAULT INFORMATION STORE/DISPLAY FUNCTIONS : Default 1ST DATA 2ND DATA RELATED COMMAND MEANING DATA MEANING DATA MEANING Fault log/Call log Whether fault logs are col- To collect collection on VoIP lected when the IP Sta- Not collected call tions login to the system or the VoIPDB is in online...
Page 587 CMEA COMMAND CODE TITLE: FAULT INFORMATION STORE/DISPLAY FUNCTIONS NOTE 4 : Confirm the following fault information, when you check Remote Unit operations by survival mode as fault information from PCPro/CAT in Remote UNIT over IP. 001: System Reset 042: Communication error occurrence between Main Unit and Remote Unit 052: Communication error restoration between Main Unit and Remote Unit When Remote Unit starts the survival mode operation, the fault information “Reset by CAT or PCPro”...
Page 588 CMEA COMMAND CODE TITLE: FAULT INFORMATION STORE/DISPLAY FUNCTIONS Fault Information Display After the following operation: ST + EA0 + DE 00 + DE The fault information is displayed on PCPro/CAT. An example of fault information display is provid- ed below: CAT mode COMMAND= EA0 +...
Page 589 CMEA COMMAND CODE TITLE: FAULT INFORMATION STORE/DISPLAY FUNCTIONS EXPLANATION OF SCREEN INFORMATION 1: Date and Time of Fault Occurrence and Restoration 2: Fault Kind No./Restoration Kind No. FAULT KIND NUMBER FAULT CONTENT System reset CS/ZT fault It is a day for periodic maintenance Activation Code error occurred during the License Activation (Center Activation) ISDN D-channel link connection failure CCIS link connection failure...
Page 590 CMEA COMMAND CODE TITLE: FAULT INFORMATION STORE/DISPLAY FUNCTIONS RESTORATION RESTORATION CONTENT KIND NUMBER ISDN D-channel link connection returned to normal condition CCIS link connection returned to normal condition Number of lockout stations restored to less than predetermined number DLC blade returned to normal condition CS/ZT returned to normal condition LAN application returned to normal condition Traffic of IP network returned to normal condition from limit bandwidth excess...
Page 591 CMEC COMMAND CODE TITLE: MAINTENANCE BY PCPro/CAT FUNCTION: This command is used for maintenance of the PBX. The functions of this command are outlined below: • Battery release • Line status display for single line telephone or Multiline Terminal • VMS Soft Key data download •...
Page 592 CMEC COMMAND CODE TITLE: MAINTENANCE BY PCPro/CAT DATA TABLE: Battery Release/Line Status Display : Default 1ST DATA 2ND DATA RELATED COMMAND MEANING DATA MEANING DATA MEANING Battery release Battery release of Battery released Unit01 + 02 + 03 + Normal operating Unit number Line status Single Line Station...
Page 593 CMEC COMMAND CODE TITLE: MAINTENANCE BY PCPro/CAT (c) Hardware Test STATUS OF STATUS OF INDICATION STATUS OF SINGLE LINE TEL. MULTILINE TERMINAL IP STATION Terminal is not connected Terminal is not connected or Terminal is not connected tip wire is grounded Terminal is connected Terminal is connected Terminal is connected...
Page 594 CMEC COMMAND CODE TITLE: MAINTENANCE BY PCPro/CAT System Data Backup 1ST DATA 2ND DATA RELATED COMMAND MEANING DATA MEANING DATA MEANING System data System data backup Start to save CM43 Y=5 backup Now saving Stand by NOTE 1 NOTE 1: You can assign only “0”...
Page 595 CMEC COMMAND CODE TITLE: MAINTENANCE BY PCPro/CAT System Data Copy : Default 1ST DATA 2ND DATA RELATED COMMAND MEANING DATA MEANING DATA MEANING System data copy All Remote units Start to copy system CM43 Y=7 from the Main unit Remote unit No. 02 data to Remote units Now copying/Sys-...
Page 596 CMEE COMMAND CODE TITLE: APPLICATION BLADE DATA ASSIGNMENT FUNCTION: This command is used to assign the IP address to connect the functions and Web consoles for each In-Skin UMS blade (CD-VM00)/Conference blade (CD-PVAA). PRECAUTION: None ASSIGNMENT PROCEDURE: 1ST DATA 2ND DATA + EE0 + (4/7 digits) (3-15 digits)
Page 597 CMEE COMMAND CODE TITLE: APPLICATION BLADE DATA ASSIGNMENT : Default 1ST DATA 2ND DATA MEANING DATA MEANING DATA MEANING Subnet Mask for XXYY XX: Unit number (01-50) XXX.XX Subnet Mask Conference blade/ YY: Slot number (01-18) ...X (Maximum 15 digits) In-Skin UMS blade XXX.XXX.XXX.XXX= 255.0.0.0-255.255.255.252...
Page 598 COMMAND CODE TITLE: CPU MEMORY DUMP F0, F1 CPU MEMORY READ/WRITE FUNCTION: These commands are used only for maintenance. DO NOT USE these commands without the assistance of a NEC engineer. ASSIGNMENT PROCEDURE: CMF0: CPU Memory Dump ZXXXXXXXX ST + + DE...
Page 599 CMF5 COMMAND CODE TITLE: LINE/TRUNK MEMORY/ALARM MEMORY READ FUNCTION: This command is used only for maintenance. DO NOT USE this command without the assistance of a NEC engineer. ASSIGNMENT PROCEDURE: 1ST DATA ST + + DE + DE (1-15 digits)
Page 600 CMF5 COMMAND CODE TITLE: LINE/TRUNK MEMORY/ALARM MEMORY READ READOUT DATA 1ST DATA REMARKS (STATUS INFORMATION) Single Line station/Virtual Line Physical Port No. station number (1-8 digits) Unit number (01-50) + XXXXXXXX X: 0-9, A (*), B (#) Slot number (01-18) + Circuit number (01-32) Multiline Terminal number Physical Port No.
Page 601 CMF5 COMMAND CODE TITLE: LINE/TRUNK MEMORY/ALARM MEMORY READ READOUT DATA 1ST DATA REMARKS (STATUS INFORMATION) 0000 YY + XXXXXXXX + YY: 00: Physical Port No. (Multi- FFFF line Terminal/Single Line station) 01: VEN (Virtual Line sta- tion/Multiline Terminal) 05: ILEN (ISDN station) XXXXXXXX: Single Line sta- tion/Virtual Line station number...
Page 602 CMF5 COMMAND CODE TITLE: LINE/TRUNK MEMORY/ALARM MEMORY READ READOUT DATA 1ST DATA REMARKS (STATUS INFORMATION) Single Line station/Virtual Line Service memory dump data of station number (1-8 digits) station/trunk XXXXXXXX X: 0-9, A (*), B (#) Multiline Terminal number <X-XXXXXXXX> represent My FXXXXXXXX Line number EFX +...
Page 603 CMF5 COMMAND CODE TITLE: LINE/TRUNK MEMORY/ALARM MEMORY READ READOUT DATA 1ST DATA REMARKS (STATUS INFORMATION) PS Line station number Optional memory dump data <X-XXXXXXXX> of station/trunk EEXXXXXXXX EFX + ISDN Line station number <X-XXXXXXXX> EFXXXXXXXX + B channel number (0/1) D000 Trunk number D511...
Page 604 CMF6 COMMAND CODE TITLE: ONLINE MP-FP COMMAND OUTPUT FUNCTION: This command is used only for maintenance. DO NOT USE this command without the assistance of a NEC engineer. ASSIGNMENT PROCEDURE: 1ST DATA 2ND DATA + DE (2 digits) (1-8 digits)
Page 605 CMF7 COMMAND CODE TITLE: HIGHWAY CHANNEL MEMORY READ/REASSIGNMENT FUNCTION: This command is used only for maintenance. DO NOT USE this command without the assistance of a NEC engineer. ASSIGNMENT PROCEDURE: 1ST DATA ST + + DE + DE (6 digits)
Page 606 CMF7 COMMAND CODE TITLE: HIGHWAY CHANNEL MEMORY READ/REASSIGNMENT CMF7 Y=9 CMF7 Y=9 is the command which reassigns the high way channel (128ch) allocation to each physical slot (slot1-6/7-12/13-18). For the physical slot, 16 channels are allocated to each slot in reset state (the high way channel allocation is in a state which is not reassigned before).
Page 607 CMF7 COMMAND CODE TITLE: HIGHWAY CHANNEL MEMORY READ/REASSIGNMENT Example: • The setting before mounting the blade Slot 01 16DLC (16) 16DLC (16) Slot 04 Slot 02 16DLC (16) 16DLC (16) Slot 05 Unit01 Slot 03 16DLC (16) 8COT (8) Slot 06 •...
Page 608 CMFA COMMAND CODE TITLE: IP STATION APPARATUS INFORMATION FUNCTION: This command is used to read the apparatus information of IP Station. PRECAUTION: None ASSIGNMENT PROCEDURE: 1ST DATA ST + FAYY/YYYY + DE (1-8 digits) DATA TABLE: 1ST DATA INDICATION MEANING DATA MEANING DATA...
Page 609 CMFA COMMAND CODE TITLE: IP STATION APPARATUS INFORMATION : Default 1ST DATA INDICATION MEANING DATA MEANING DATA MEANING term term Read the IP Station IP Station No. 75 (D Series E) type (IP adapter type) term XXXXXXXX IP INASET term term 85 (D Series i)
Page 610 CMFA COMMAND CODE TITLE: IP STATION APPARATUS INFORMATION : Default 1ST DATA INDICATION MEANING DATA MEANING DATA MEANING Read the IP Sta- Block No. IP Station No. tion number regis- tered in Fixed XXXXXXXX Connection Mode Clear NOTE 4 NONE No data NOTE 5 Read the IP Sta-...
Page 611 CMFA COMMAND CODE TITLE: IP STATION APPARATUS INFORMATION NOTE 1: ICMP TYPE used in this feature is as follows. ICMP CLASSI- GENERAL DESCRIPTION MEANING TYPE FICATION Reply Reply to the echo request by executing the • Ping reply (ping OK) ping command (echo reply).
Page 612 CMFA COMMAND CODE TITLE: IP STATION APPARATUS INFORMATION NOTE 2: If ICMP TYPE not listed above is received, “HARDWARE ERROR” is displayed. NOTE 3: TOS (Type of Service) is present in IP header, and represents QoS (Quality of Service). Precedence/delay/throughput/reliability that determine quality are contained within TOS. NOTE 4: The station number for Fixed Connection Mode registered by CM12 Y=92 is read by this command.
Page 613 CMFB COMMAND CODE TITLE: REMOTE PROGRAM DOWNLOAD INFORMATION READ FUNCTION: This command is used only for maintenance. DO NOT USE this command without the assistance of a NEC engineer. ASSIGNMENT PROCEDURE: 1ST DATA ST + FBYY + DE (4 digits)
Page 614 UNIVERGE SV8300 Command Manual TERMINAL KEY ASSIGNMENT Appendix This appendix contains the key number layout of each DT300 term term Series, DT700 Series, D IP, DESKCON, DSS Console, and Add-On Module. Refer to this appendix when you assign a key function by CM90 or CM97.
Page 615 Appendix A TERMINAL KEY ASSIGNMENT DT300/DT700 Series Key Numbers Key Numbers Help Exit (01) (02) (03) (04) (05) (06) (07) (08) (09) (10) (11) (12) (91) (90) Recall Feature (95) Answer Menu DTL-12D-1D Redial (93) Hold Transfer Speaker (97) (96) (94) NOTE: The table below shows the key layout for Line/Trunk/Feature Keys and One Touch Keys of the...
Page 616 Appendix A TERMINAL KEY ASSIGNMENT DT300/DT700 Series Key Numbers Example: 24 Line/Trunk/Feature Keys Exit Help (01) (02) (03) (04) (05) (06) (07) (08) (09) (10) (11) (12) (13) (14) (15) (16) (17) (18) (91) (90) Feature Recall (95) Answer Menu Redial (93) Hold...
Page 617 Appendix A TERMINAL KEY ASSIGNMENT DT300/DT700 Series Key Numbers Key Numbers Exit Help (05) (01) (02) (06) (03) (07) (04) (08) Scroll (91) (90) Feature Recall (95) Answer Menu DTL-8LD-1D Redial (93) Hold Transfer Speaker (97) (96) (94) NOTE: The table below shows the key layout for Line/Trunk/Feature Keys and One Touch Keys of the Multiline Terminals.
Page 618 Appendix A TERMINAL KEY ASSIGNMENT DT300 Series Key Numbers [8300R2] Key Numbers Help Exit (01) (02) (03) (04) (05) (06) (07) (08) (09) (10) (11) (12) (91) (90) Feature Recall (95) DTL-12BT-1 Answer Menu Redial (93) Hold Transfer Speaker (97) (96) (94) NOTE:...
Page 619 Appendix A TERMINAL KEY ASSIGNMENT term term Series i/D IP Key Numbers term Series i (01) (02) (03) (04) (05) (06) (07) (08) Recall Feature (98) (90) (91) Directory Conf (99) (92) Message Redial PQRS WXYZ (93) Answer (95) Transfer Speaker Hold (97)
Page 620 Appendix A TERMINAL KEY ASSIGNMENT term term Series i/D IP Key Numbers term Series i Exit Help (01) (02) (03) (04) (05) (06) (07) (08) Recall Feature (98) Directory (90) (91) NOTE 1 Conf (99) Message (92) Redial PQRS WXYZ (93) Answer (95)
Page 621 Appendix A TERMINAL KEY ASSIGNMENT term term Series i/D IP Key Numbers term Series i Exit Help (01) (02) (03) (04) (05) (06) (07) (08) (09) (10) (11) (12) (13) (14) (15) (16) Recall Feature (98) (90) (91) Directory NOTE 1 Conf (99) Message...
Page 622 Appendix A TERMINAL KEY ASSIGNMENT term term Series i/D IP Key Numbers Example: 16 Line/Trunk/Feature Keys + 16 One-Touch Keys term Series i Exit Help (01) (02) (03) (04) (05) (06) (07) (08) (09) (10) (11) (12) (13) (14) (15) (16) Recall Feature...
Page 623 Appendix A TERMINAL KEY ASSIGNMENT term term Series i/D IP Key Numbers term Series i Exit Help (01) ( 0 9 ) ( 0 2 ) (10 ) ( 0 3 ) ( 11 ) ( 0 4 ) ( 1 2 ) ( 0 5 ) ( 1 3 ) ( 0 6 )
Page 624 Appendix A TERMINAL KEY ASSIGNMENT term term Series i/D IP Key Numbers term Key Numbers Exit Help (01) (02) (03) (04) (05) (06) (07) (08) (91) PQRS WXYZ Feature (90) Recall (92) DTR-8D-1R Conf (93) Redial (94) Speaker (97) (96) (95) (98) Hold...
Page 625 Appendix A TERMINAL KEY ASSIGNMENT term term Series i/D IP Key Numbers term Key Numbers Exit Help (01) (02) (03) (04) (05) (06) (07) (08) (09) (10) (11) (12) (13) (14) (15) (16) (91) PQRS WXYZ Feature (90) Recall (92) DTR-16D-1R Conf (93)
Page 626 Appendix A TERMINAL KEY ASSIGNMENT term term Series i/D IP Key Numbers Example: 16 Line/Trunk/Feature Keys + 16 One-Touch Keys Exit Help (01) (02) (03) (04) (05) (06) (07) (08) (09) (10) (11) (12) (13) (14) (15) (16) (91) Feature (90) Recall (92)
Page 627 Appendix A TERMINAL KEY ASSIGNMENT term 75 Key Numbers term Key Numbers (01) (02) (03) (04) (06) (07) (08) (05) (91) Feature (90) Recall (92) Conf (93) Redial (97) (96) (95) (94) DTP-8-1 Answer Transfer Speaker Hold NOTE: The table below shows the key layout for Line/Trunk/Feature Keys and One Touch Keys of the Multiline Terminals.
Page 628 Appendix A TERMINAL KEY ASSIGNMENT term 75 Key Numbers term Key Numbers (01) (02) (03) (04) (05) (06) (07) (08) (91) Feature (90) Recall (92) Conf DTP-8D-1 (93) Redial (97) (96) (95) (94) Answer Speaker Hold Transfer NOTE: The table below shows the key layout for Line/Trunk/Feature Keys and One Touch Keys of the Multiline Terminals.
Page 629 Appendix A TERMINAL KEY ASSIGNMENT term 75 Key Numbers term Key Numbers (01) (02) (03) (04) (05) (06) (07) (08) (09) (10) (11) (12) (13) (14) (15) (16) (91) Feature (90) Recall (92) Conf DTP-16D-1 (93) Redial (97) (96) (95) (94) Answer Speaker...
Page 630 Appendix A TERMINAL KEY ASSIGNMENT term 75 Key Numbers Example: 16 Line/Trunk/Feature Keys + 16 One Touch Keys (01) (02) (03) (04) (06) (07) (08) (05) (09) (10) (11) (12) (13) (16) (14) (15) (91) Feature (90) Recall (92) Conf DTP-32D-1 (93) Redial...
Page 631 Appendix A TERMINAL KEY ASSIGNMENT DESKCON Key Numbers (01) (02) (03) (04) Night Busy ATND NANS Recall PAGE (13) (14) (15) (16) (17) (18) (19) (20) (21) (22) Start Mute Position Busy Call Park (23) (24) (26) (27) (31) (32) Cancel L6 (12) Volume...
Page 632 Appendix A TERMINAL KEY ASSIGNMENT DSS Console Key Numbers DCR-60-1R Continued on next page A-19 NWA-033623-001 Rev.3.0 91apa001.fm...
Page 633 Appendix A TERMINAL KEY ASSIGNMENT DSS Console Key Numbers DCU-60-1 Continued on next page A-20 NWA-033623-001 Rev.3.0 91apa001.fm...
Page 634 Appendix A TERMINAL KEY ASSIGNMENT DSS Console Key Numbers EDW-48-2 A-21 NWA-033623-001 Rev.3.0 91apa001.fm...
Page 635 Appendix A TERMINAL KEY ASSIGNMENT Add-On Module Key Numbers DCU-60-1 Continued on next page A-22 NWA-033623-001 Rev.3.0 91apa001.fm...
Page 636 Appendix A TERMINAL KEY ASSIGNMENT Add-On Module Key Numbers EDW-48-2 A-23 NWA-033623-001 Rev.3.0 91apa001.fm...
Page 637 THIS PAGE LEFT BLANK INTENTIONALLY. A-24 NWA-033623-001 Rev.3.0 91apa001.fm...

NEC UNIVERGE SV8300 Command Manual

Introduction

Chapter 1 HOW to USE CAT

Chapter 2 PRECAUTION

Chapter 3 COMMAND DESCRIPTION

Appendix A TERMINAL KEY ASSIGNMENT

Quick Links

Summary of Contents for NEC UNIVERGE SV8300

Page 4: Table Of Contents

Page 11: Outline Of This Manual

Page 12: Terms In This Manual

Page 13: Terminal Name

Page 15: Reference Manual

Page 17: Cat And Pcpro

Page 18: Cat Key Functions

Page 23: Cat Mode Setting Procedure

Page 25: Notice On Cat Mode

Page 31: Cat Operation

Page 35: Error Messages

Page 39: Conditions For Using Commands

Page 43: Method Of Setting On-Line/Off-Line Mode

Page 45: Password Entry

Page 47: Nation Code Assignment

Page 48: System Data Backup

Page 50: Command Description

Page 51: How To Read This Chapter

Page 58: Setting For Each Unit

Page 158: Unit Configuration

Page 255: Assignment/Station Digest Authentication Password Assignment

Page 389: Group Call

Page 403: Number Of Queue Limit, Trunk Access Code For Mobility Access Mode, Isdn Alternating Routing

Page 539: Traffic Measurement

NEC UNIVERGE SV8300 Command Manual

Introduction

Chapter 1 HOW to USE CAT

Chapter 2 PRECAUTION

Chapter 3 COMMAND DESCRIPTION

Appendix A TERMINAL KEY ASSIGNMENT

Quick Links

Related Manuals for NEC UNIVERGE SV8300

Summary of Contents for NEC UNIVERGE SV8300

Table of Contents