Advertisement
Quick Links
thank you for purchasing a Sealey product. manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Wear eye
refer to
instruction
protection
manual
1. SaFetY
1.1.
electrical SaFetY
‰
warNiNG! it is the user's responsibility to check the following:
check all electrical equipment and appliances to ensure that they are safe before using. inspect power supply leads, plugs and all
electrical connections for wear and damage. sealey recommend that an rcd (residual current device) is used with all electrical
products. You may obtain an rcd by contacting your local sealey stockist.
if the product is used in the course of business duties, it must be maintained in a safe condition and routinely PAt (Portable Appliance
test) tested.
electrical safety information: it is important that the following information is read and understood.
1.1.1.
ensure that the insulation on all cables and on the appliance is safe before connecting it to the power supply.
1.1.2.
regularly inspect power supply cables and plugs for wear or damage and check all connections to ensure that they are secure.
important: Ensure that the voltage rating on the appliance suits the power supply to be used and that the plug is fitted with the correct
1.1.3.
fuse - see fuse rating in these instructions.
8
do Not pull or carry the appliance by the power cable.
8
do Not pull the plug from the socket by the cable.
8
do Not use worn or damaged cables, plugs or connectors. ensure that any faulty item is repaired or
replaced immediately by a qualified electrician.
This product is fitted with a BS1363/A 13 Amp 3 pin plug.
1.1.4.
if the cable or plug is damaged during use, switch the electricity supply and remove from use.
Ensure that repairs are carried out by a qualified electrician.
Replace a damaged plug with a BS1363/A 13 Amp 3 pin plug. If in doubt contact a qualified electrician.
A) Connect the GREEN/YELLOW earth wire to the earth terminal 'E'.
B) Connect the BROWN live wire to the live terminal 'L'.
C) Connect the BLUE neutral wire to the neutral terminal 'N'.
ensure that the cable outer sheath extends inside the cable restraint and that the restraint is tight.
Sealey recommend that repairs are carried out by a qualified electrician.
1.2.
GeNeral SaFetY
9
familiarise yourself with the application, limitations and potential hazards of the lathe.
‰
warNiNG! disconnect the lathe from the mains power before changing accessories, servicing or performing any maintenance.
9
maintain the lathe in good condition (use an authorised service agent to service and maintain the motor).
9
replace or repair damaged parts. Use genuine parts only. Unauthorised parts may be dangerous and will invalidate the warranty.
‰
warNiNG! Keep all guards and holding screws in place, tight and in good working order. check regularly for damaged parts.
9
locate lathe in a suitable work area. Keep area clean and tidy, free from unrelated materials and ensure that there is adequate lighting.
9
Keep the lathe clean for best and safest performance and check moving parts alignment regularly.
9
Keep turning tools clean and sharp for best and safest performance.
9
ensure that there are no flammable or combustible materials near the work area.
warNiNG! Always wear approved eye or face protection when operating the lathe (standard spectacles are not adequate). Wear
‰
approved ear defenders and use a face or dust mask if dust is generated.
9
Keep hands and body clear when operating the lathe. do Not reach across the lathe.
9
maintain correct balance and footing. ensure the floor is not slippery and wear non-slip shoes.
Remove ill fitting clothing. Remove ties, watches, rings and other loose jewellery and contain and/or tie back long hair.
9
9
Keep children and unauthorised persons away from the work area.
9
remove all wrenches, hex keys etc. from the lathe and its vicinity before turning it on.
9
Avoid unintentional starting and ensure the lathe power switch is "off" before plugging into the mains power supply.
8
do Not use the lathe for a task that it is not designed to perform.
do Not operate the lathe if any parts are damaged or missing, as this may cause failure and/or personal injury.
8
‰
warNiNG! do Not use the lathe to cut any materials other than wood.
8
do Not stand or climb on the lathe.
8
do Not get the lathe wet or use in damp or wet locations or areas where there is condensation.
8
do Not use any tools other than those appropriate to wood turning.
8
do Not pull the plug from the power socket by the cable.
© Jack sealey limited
instructions for
wood lathe 1000mm
model no:
Wear ear
Wear protective
protection
clothing
Original Language Version
Sm1308
Wear face
indoor
use only
mask
replacement fuse
13amP
rating:
Issue 4 (H, 3, F) 01/02/18
sM1308
Advertisement
Related Manuals for Sealey SM1308
Summary of Contents for Sealey SM1308
- Page 1 Sm1308 model no: thank you for purchasing a Sealey product. manufactured to a high standard, this product will, if used according to these instructions, and properly maintained, give you years of trouble free performance. IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED.
- Page 2 Four turning speed options to suit a variety of jobs. Fitted with a BS approved, non-rewirable 3 pin plug and cable. SPeciFicatioN model no..............sm1308 turning Capacity Over Bed ........350mm turning capacity over tool rest ........ 300mm thread size (Headstock spindle) ......
- Page 3 4.3.6. see 4.4.1 onward for operating the lathe. fig.4 fig.5 fig.6 Speed setting is visible without removing a panel Issue 4 (H, 3, F) 01/02/18 sM1308 Original Language Version © Jack sealey limited...
- Page 4 Guarantee is 12 months from purchase date, proof of which is required for any claim. Sealey Group, Kempson way, Suffolk business Park, bury St edmunds, Suffolk. iP32 7ar 01284 757500 01284 703534 sales@sealey.co.uk...