Set Up the Machine Before Setting Up the Machine Remove all shipping tape on the machine. ● When moving the machine, be sure at least two people carry it using the provided hand grips on the left and ● right sides, as seen in the illustration right.
If you have a problem with your machine and you cannot solve it by referring to the manuals listed above, please contact our Canon Authorized Service Facilities or the Canon Customer Care Center at -800-88-4040 between the hours of 8:00 A.M. to 8:00 P.M. EST Monday through Friday and 0:00 A.M. to 8:00 P.M. on Saturday.
Install Cartridge Remove the seals ( places). Remove the toner cartridge from the bag. Keep the bag for future use. Bend back the blue plastic pull tab as in the illustration above. Do not open the drum protective shutter (A). Do not remove the pull tab as it is used to pull out the toner when the cartridge needs replaced.
Page 6
Push the toner cartridge to make sure it is properly set in Open the left cover. the machine. Do not touch the fixing assembly (A) as it becomes very hot during use. Hold the toner cartridge by its handle. Insert the toner cartridge into the machine with the arrows (A) on the toner cartridge pointing toward the machine.
Load Paper Gently insert the paper cassette as far as it will go. Pull out the paper cassette until it stops. Be careful not to get your fingers caught. For loading paper in the multi-purpose tray, see Chapter , “Document and Paper, ” in the Basic Operation Guide, Reference Guide >...
Page 8
Set Up the Paper Cassette to Fit the Paper Size Incline the rear paper end guide until it is unlocked, then remove it from the paper cassette. Attach the guide to the slots of the desired paper size.
Page 9
Connect the Power Cord and Turn On the Machine Connect the power cord into the rear socket and the wall outlet and press the [I] side of the main power switch to When restarting the machine, wait at least 0 seconds before turning the main power back on.
Connect Telephone Cables Connect the supplied telephone cable to the line jack (A) and the wall jack. Connect your external telephone to the external device jack (B) if required. If you want to use an external telephone and receive faxes, you will need to set up the receiving mode. (See “Set the Machine for Receiving Faxes, ”...
Page 11
Install Handset (Optional) Use a screwdriver to remove the cover on the right side of Screw the bracket onto the machine with the screws (A). the machine. Place the handset on the cradle. Attach the screws included with the machine to the If using the handset or an external telephone, make sure to set center screw holes, and attach the driver instruction label the fax receive mode to <FaxTel>...
Page 12
Set the Date and Time You can set the current date and time. The current date and time settings are used as standard timer settings for functions that require them. Use the keys both on the touch panel display and the control panel to enter information. Numeric keys: Enter letters and numbers.
Page 13
Press [Additional Functions]. Use [ ] or [ ] to select <8. TIMER SETTINGS>, then press [OK]. Confirm that <. DATE&TIME SETTING> is displayed, then press [OK]. Use the numeric keys to enter the date (month/ day/year) and time (in 4- hour format), then press [OK].
Page 14
Set the Telephone Line Type Press [Additional Functions]. Use [ ] or [ ] to select <5. TX/RX SETTINGS>, then press [OK]. Use [ ] or [ ] to select <. FAX SETTINGS>, then press [OK]. Use [ ] or [ ] to select <.
Guidelines for Entering Information The sender information you register in the machine appears in the header of each page received by your recipient. 06/30 2007 10:50 0001/0001 Sender Information FAX (404)XXX-XXXX CANON SALES Date Time Fax Number Sender's Page Number Name (TTI) Before sending documents, you MUST register your fax number, user name, and the current date and time in the machine.
Page 16
You can enter the following characters in each input mode:...
Your name: John Smith ‒ Company name: Canon ‒ Company name and department: Canon-Accounting Dept. ‒ Press [Additional Functions]. Press [Additional Functions] twice. Use [ ] or [ ] to select <5. TX/RX Confirm that <. TX/RX COMMON SET.> is SETTINGS>, then press [OK].
Page 18
Set the Machine for Receiving Faxes Select the Receive Mode that Suits Your Needs Follow the chart below to determine the correct receive mode for your needs Do you intend to use the machine to <FaxOnly> receive voice calls? Do you intend to use an answering <AnsMode>...
Page 19
Set the Receive Mode Press [Additional Functions]. Use [ ] or [ ] to select <5. TX/RX SETTINGS>, then press [OK]. Use [ ] or [ ] to select <. FAX SETTINGS>, then press [OK]. Confirm that <. RX MODE> is displayed, then press [OK].
Page 20
Set the Machine for Network Usage Connect the Machine to a Network This machine has a USB connector and LAN connector. If the machine is connected to a network using a LAN cable, you can print the documents sent from a computer, send documents to a file server, i-fax and send document attached to an e-mail through a network.
Specify the IP Address Settings An IP address must be specified in order to enable communication between the machine and computer. – To use a network environment with the LASER CLASS 80, an optional network printer kit is required. – It is recommended that the network administrator perform the following procedures.
PCL6 is an advanced version of PCL5e and offers superior printing quality and speed. This machine supports the PCL5e and PCL6 printer drivers. UFRII LT: This is the Canon UFRII LT printer driver. This driver enables you to print from any application software ●...
Page 23
Before Installation: • Do not connect the USB cable before installing the software. If you connect the USB cable before installing the software and the Found New Hardware Wizard screen appears, click [Cancel]. • For Windows 2000/XP/Server 2003/Vista, log on as Administrator to install the software. •...
Page 24
Installation Procedure for USB Connection Select the driver(s) you want to install. – The following indicates the procedure for installing the UFR II Printer Driver, PCL Printer Driver, and Fax Driver all together. (The PCL Printer Driver is only available for the LASER CLASS 830i.) –...
Page 25
Connect the machine and your computer with a USB cable (C). Connect the machine to the network correctly, and confirm that the power is on. If you are using Windows XP, [Found New Hardware Wizard] dialog box appears. Select [Install Software Automaticall (Recommended)] then click [Next].
Page 26
If you selected to install Fax Driver in step 3, proceed to step 5. If you did not select the Fax Driver in step 3, Select [Canon LC800/L3000 PCL5e] proceed to step 35. and/or [Canon LC800/L3000 PCL6]. The selected drivers are installed.
Page 27
Select the USB port that was created when you installed the UFR II Printer Driver. You have now completed installation.
Page 28
Installation Procedure for Network Connection If the CD-ROM Setup screen is not displayed, click [start] on the Windows Connect the machine to the network task bar → [My Computer]. correctly, and confirm that the power Windows Vista: click [start] on the is on.
Page 29
[Process to Install Printer Driver] in this dialog box appears if drivers that can be installed with this Installer are already installed. You have now completed installation. Repeat the steps from 6 if you have selected the two or three drivers in step 3.
Confirming the installation Check if the drivers are installed successfully and that the machine is selected as the default printer. If your machine is selected in the [Printer] area when you open the [Print] dialog box from an application, your machine is set as the default printer.
Page 31
Readme file and online help for this program. Canon Font Manager ● Canon Font Manager is utility software that allows you to install and uninstall fonts, etc.. For details, see the Readme file and online help for this program. –...
Using Help The User Software CD includes programs (driver software and application software) which the supplied instruction guides do not cover. When you utilize such programs, refer to online help following the instructions below. Online Help You can locate additional help in the online help file provided with the driver software.
Page 33
If you have a problem with your machine and you cannot solve it by referring to the manuals, please contact our Canon Authorized Service Facilities or the Canon Customer Care Center at -800-88-4040 between the hours of 8:00 A.M. to 8:00 P.M. EST Monday through Friday and 0:00 A.M. to 8:00 P.M. on Saturday.
User Manual CD-ROM (Reference Guide) The User Manual CD-ROM (Reference Guide) is software that enables you to select and view HTML Manuals included on the CD-ROM via your computer screen. Follow the instructions below to use the User Manual CD- ROM (Reference Guide).
Page 35
Using the User Manual CD-ROM (Reference Guide) When using the Reference Guide with Windows, follow the steps below. 1. Insert the User Manual CD-ROM in your computer. 2. Select whether to install the Reference Guide in your computer, or display the Reference Guide from the CD- ROM.
Page 36
Select an appendix category to display the topic pages not related to functions, such as the maintenance and troubleshooting topics. I [Office Locations] Click to display Canon contact details in a separate window. – Select to create a shortcut for the Reference Guide on your desktop.
Page 38
CANON INC. 30-2, Shimomaruko 3-chome, Ohta-ku, Tokyo 146-8501, Japan CANON U.S.A., INC. One Canon Plaza, Lake Success, NY 11042, U.S.A. CANON CANADA INC. 6390 Dixie Road Mississauga, Ontario L5T 1P7, Canada CANON EUROPA N.V. Bovenkerkerweg 59-61 1185 XB Amstelveen, The Netherlands CANON FRANCE S.A.S.