Advertisement
Quick Links
P RO G R A M M I N G O P T I O N S
T T o o A A c c c c e e s s s s t t h h e e P P r r o o g g r r a a m m m m i i n n g g M M e e n n u u s s
Press and hold
until
appears on the LCD screen.Then press the key that
corresponds with the desired menu option and follow the instructions below.
Menu Option
Key
Programming
Ringer Melody
1
Press
1-5 to select a new melody. Press
Dialing Mode
2
Press
1 for tone, 2 for pulse. Press
3
Flash Duration
Press
select duration. 1 = 600ms, 2 = 300ms, 3 = 150ms, 4 = 100ms,
5 = 80ms. Press
Local Number*
4
Press
appear on the LCD screen when the phone is in standby.
Press
5
Conference*
Press
Conference key to dial. Press
Service*
Press
6
0
key to dial. Press
Press CLEAR once to return to the previous menu level or hold to exit
Programming mode without saving changes.
*Press and hold the "1" key to enter a hyphen or the "*" key to enter a space in the
been programmed, use CLEAR to delete the old number bef
C C A A U U T T I I O O N N : Read the Safety Information in the instruction manual.
!
© 2005 . All rights reserved. No part of this document may be reproduced in any form or by any means without written
permission from NEC. NEC reserves specific privileges. Information in this document is subject to change without notice.
NEC Conference MaxPlus is protected by U.S. Patent No. D499,392 Part No. 800-157-201 Rev. 1.0
Printed in China.
. The current melody selection will flash. Press
to save selection.
. The current dialing selection will flash. Press
to save selection.
. The current duration will flash. Press 1-5 to
to save selection.
. Enter the phone number that you want to
to save selection.
. Enter the phone number that you want the
to save the number.
. Enter the phone number that you want the
to save the number.
. I f a number has alrea
ore entering the n
ew number.
NEC Conference Max Plus
A A u u d d i i o o C C o o n n f f e e r r e e n n c c i i n n g g
C O N F E R E N C E P H O N E S E T U P
T T o o C C o o n n n n e e c c t t a a n n d d C C h h a a r r g g e e B B a a t t t t e e r r i i e e s s
1. Slide the cover off the battery compartment on the bottom of the pod.
2. Connect the battery pack plug into the port in the compartment and insert the
battery pack. Slide the cover back into place.
F F i i g g u u r r e e 1 1 . . C C o o n n n n e e c c t t i i n n g g a a n n d d c c h h a a r r g g i i n n g g t t h h e e b b a a t t t t e e r r y y
3. Connect the power supply/charger to the conferencing pod and plug it into an
electrical outlet. Charge batteries for 15 hours prior to first use.
T T o o C C o o n n n n e e c c t t B B a a s s e e U U n n i i t t
1. Connect one end of the telephone
cable into the phone jack on the
back of the base unit and the other
end into a wall jack.
2. Connect a recording device to the
2.5mm audio jack (if desired).
3. Connect the power cord to the
base unit and plug it into an
electrical outlet. The base unit
may be located up to 150 feet
from the conferencing pod.
Getting Started Guide
In Use and
Power LEDs
Paging button
F F i i g g u u r r e e 2 2 . . C C o o n n n n e e c c t t i i n n g g t t h h e e b b a a s s e e u u n n i i t t
Advertisement
Related Manuals for NEC Conference Max Plus
Summary of Contents for NEC Conference Max Plus
- Page 1 F F i i g g u u r r e e 2 2 . . C C o o n n n n e e c c t t i i n n g g t t h h e e b b a a s s e e u u n n i i t t permission from NEC. NEC reserves specific privileges. Information in this document is subject to change without notice.
- Page 2 N N E E C C C C o o n n f f e e r r e e n n c c e e M M a a x x P P l l u u s s Getting Started Guide K E Y PA D F U N C T I O N S U S I N G T H E P H O N E...