Advertisement
Quick Links
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Wear eye
refer to
instruction
protection
manual
1. SAFETY
WARNING! ensure Health & safety, local authority and general workshop practice regulations are adhered to when using this
‰
equipment.
familiarise yourself with the applications, limitations and the potential hazards of the tyre changer.
9
maintain the tyre changer in good condition (use an authorised service agent).
9
replace or repair damaged parts. Use genuine parts only. Unauthorised parts may be dangerous and will invalidate the warranty.
9
WARNING! check regularly for damaged parts. Any part that is damaged must be repaired or replaced before the equipment is next
‰
used.
locate the tyre changer in a suitable work area and keep area clean and tidy and free from unrelated materials. ensure that there is adequate
9
lighting.
WARNING! use on a level surface, preferably concrete, to which the tyre changer must be bolted.
‰
Keep the tyre changer clean for best and safest performance.
9
Wear approved safety eye protection (standard spectacles are not adequate).
9
Keep hands and feet well clear of the bead breaker.
9
maintain correct balance and footing. ensure the floor is not slippery and wear non-slip shoes.
9
remove ill fitting clothing. remove ties, watches, rings and other loose jewellery and contain and/or tie back long hair.
9
Keep children and unauthorised persons away from the work area.
9
DO NOT use the tyre changer for any purpose other than that for which it is designed.
8
DO NOT operate the tyre changer if any parts are damaged or missing as this may cause failure and/or personal injury.
8
DO NOT allow untrained persons to operate the tyre changer.
8
DO NOT stand on the tyre changer.
8
DO NOT operate the tyre changer when you are tired or under the influence of alcohol, drugs or intoxicating medication.
8
2. INTRODUCTION
steel construction with manual bead breaker. suitable for use on most open centred wheels. supplied with tyre bar. to prevent damage to the
rims of an alloy wheel, it is essential to use a tc963 tyre Bar.
3. SpECIFICATION
Model no: .............................................................. TC960.V2
min. Wheel diameter ............................................................n/a
max. Wheel diameter ...........................................................n/a
min. Wheel depth ..............................................................0mm
max. Wheel depth .........................................................300mm
Working Height ..............................................................640mm
centre Post sizes ............................................................41mm
4. ASSEMbLY
Numbers/letters in brackets refer to those shown in the parts diagram.
4.1.
Attach the pedestal (3) to the base (1) using the bolts (11), washers (14) and nuts (12) provided. note that the longer end of the base
should be below the bead breaker (7).
4.2.
Attach the two side base channels (2) to the pedestal using bolts, washers and nuts, as above.
Note: there are two holes in the base and one in each side base for securely mounting the tyre changer to the floor.
5. OpERATION
the TC960 tyre changer is manually operated - no air supply is required. it is designed for removing/fitting tyres from/to most
5.1.
sizes of open-centre wheels (see section 3 specification). DO NOT use the tyre changer for any other purpose.
5.2.
if tyres are to be changed on aluminium wheels the optional tyre bar, sealey model no. TC963, must be used to prevent damage to the
wheel rims.
▲
IMpORTANT! never attempt to fit or remove a tyre without first lubricating both beads (lubricant not supplied).
5.3.
bead breaking - refer to fig. 1
5.3.1.
deflate the tyre and remove all balance weights.
© Jack sealey limited
instructions for
MANUAL TYRE CHANGER
model no:
Wear
Wear
safety
protective
footwear
gloves
Original Language Version
TC960.V2
tc960.V2 | issue 1 23/11/17
Advertisement
Related Manuals for Sealey TC960.V2
Summary of Contents for Sealey TC960.V2
- Page 1 (see section 3 specification). DO NOT use the tyre changer for any other purpose. 5.2. if tyres are to be changed on aluminium wheels the optional tyre bar, sealey model no. TC963, must be used to prevent damage to the wheel rims.
- Page 2 Important: no liability is accepted for incorrect use of this product. Warranty: Guarantee is 12 months from purchase date, proof of which is required for any claim. Sealey Group, Kempson Way, Suffolk business park, bury St Edmunds, Suffolk. Ip32 7AR 01284 757500 01284 703534 sales@sealey.co.uk...