Advertisement
Quick Links
thank you for purchasing a sealey product. Manufactured to a high standard this product will, if used according to these instructions and properly
maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS.
USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE
DAMAGE AND/OR PERSONAL INJURY AND/OR WILL INVALIDATE THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAFETY INSTRUCTIONS
1.1 .
ELECTRICAL SAFETY
WARNING! It is the responsibility of the owner and the operator to read, understand and comply with the following:
You must check all electrical products, before use, to ensure that they are safe. You must inspect power cables, plugs, sockets and
any other connectors for wear or damage. You must ensure that the risk of electric shock is minimised by the installation of
appropriate safety devices. A residual current circuit Breaker (rccB) should be incorporated in the main distribution board. We also
recommend that a residual current device (rcd) is used. It is particularly important to use an rcd with portable products that are
plugged into a supply which is not protected by an rccB. If in any doubt consult a qualified electrician. You may obtain a residual
current device by contacting your sealey dealer.
You must also read and understand the following instructions concerning electrical safety.
1.1.1. the electricity at Work Act 1989 requires that all portable electrical appliances, if used on business premises, are tested by a qualified
electrician, using a Portable Appliance tester (PAt), at least once a year.
1.1.2. the Health & safety at Work Act 1974 makes owners of electrical appliances responsible for the safe condition of those appliances
and the safety of the appliance operators. If in any doubt about electrical safety, contact a qualified electrician.
1.1.3. ensure that the insulation on all cables and on the appliance is safe before connecting it to the power supply. see 1.1.1. and 1.1.2.
and use a Portable Appliance tester.
1.1.4. ensure that cables are always protected against short circuit and overload.
1.1.5. regularly inspect power supply cables and plugs for wear or damage and check all
connections to ensure that none are loose.
1.1.6. Important: ensure that the voltage marked on the appliance matches the power supply
to be used and that the plug is fitted with the correct fuse - see fuse rating at right.
1.1.7. do not pull or carry the appliance by the power cable.
1.1.8. do not pull the plug from the socket by the cable.
1.1.9. do not use worn or damaged cables, plugs or connectors. Immediately have any faulty
item repaired or replaced by a qualified electrician. When a Bs 1363/A uK 3 pin plug is
damaged, cut the cable just above the plug and dispose of the plug safely.
fit a new plug according to the following instructions (uK only).
a) Connect the GREEN/YELLOW earth wire to the earth terminal 'E'.
b) Connect the BROWN live wire to the live terminal 'L'.
c) Connect the BLUE neutral wire to the neutral terminal 'N'.
d) After wiring, check that there are no bare wires, that all wires have been correctly connected, that the cable outer
insulation extends beyond the cable restraint and that the restraint is tight.
double insulated products, which are always marked with this symbol
to rewire, connect the wires as indicated above do not connect either wire to the earth terminal.
1.1.10. Products which require more than 13 amps are supplied without a plug. In this case you must contact a qualified electrician to ensure
that a suitably rated supply is available. We recommend that you discuss the installation of an industrial round pin plug and socket
with your electrician.
1.1.11. If an extension reel is used it should be fully unwound before connection. A reel with an rcd fitted is preferred since any appliance
plugged into it will be protected. the cable core section is important and should be at least 1.5mm², but to be absolutely sure that the
capacity of the reel is suitable for this product and for others which may be used in the other output sockets, we recommend the use
of 2.5mm² section cable.
1.2.
GENERAL SAFETY
WARNING! Ensure Health & Safety, local authority, and general workshop practice regulations are adhered to when using this lamp.
do not immerse lamp in water.
ensure the lamp is disconnected from the mains before attempting to change the fluorescent tube.
Maintain the lamp in good condition (use an authorised service agent).
ensure there are no flammable liquids or vapours present.
DO NOT use lamp for any purpose other than that for which it is designed.
DO NOT pull the cord to remove the plug from the power supply.
When not in use unplug from the mains power supply and store in a safe, dry, childproof area.
2. INTRODUCTION
spring loaded telescopic bracket, mounts under open bonnet with foam rubber covers to prevent damage. 30W 900mm fluorescent tube
with tough composite clear guard gives complete engine bay illumination. lamp unit can be unclipped from mounting bracket, used
separately or can be hung via 360°swivel hook. supplied with 4.5mtr cable and AstA/Bs approved 3-pin moulded plug.
3. OPERATION
note: If lamp fails to operate ensure tube has been rotated 45° from the insertion position ensuring
good contact.
3.1.
Insert the lamp into the bracket and secure, see fig.2A then fig.3A.
3.2.
Attach to the underside of the car bonnet by pulling the spring loaded bracket arms apart (fig.4)
and allowing them to close around the bonnet sides.
3.3.
the spring loaded bracket may also be unclipped to allow the lamp to be hung in the vertical
position using the hook mount.
3.4.
to turn the lamp on, plug into the mains supply and press the switch on the bottom of the lamp
(fig.1).
3.5.
to turn off, switch off the lamp, switch off at the mains and remove the plug from the socket.
InstructIons for:
UNDER BONNET NEON LEAD LAMP 30W
Model no:
, are fitted with live (brown) and neutral (blue) wires only.
Original Language Version
ML30
Yellow & Green
Earth Wire
Blue
Neutral
Wire
FUSE RATING 3 AMP
Brown
Live
Wire
Cable
Restraint
fig.1
Ml30 Issue: 4 - 13/04/10
Advertisement
Related Manuals for Sealey ML30
Summary of Contents for Sealey ML30
- Page 1 ML30 Model no: thank you for purchasing a sealey product. Manufactured to a high standard this product will, if used according to these instructions and properly maintained, give you years of trouble free performance. IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS.
- Page 2 INFORMATION: for a copy of our latest catalogue and promotions call us on 01284 757525 and leave your full name and address, including postcode. Sole UK Distributor, Sealey Group, www.sealey.co.uk 01284 757500 Kempson Way, suffolk Business Park, Bury st. edmunds, suffolk, sales@sealey.co.uk 01284 703534 email IP32 7Ar Original Language Version Ml30 Issue: 4 - 13/04/10...