Advertisement
Quick Links
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions and maintained properly, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT
CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL
INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to Instruction
Manual
1. SAFETY
WARNING! use workstation on level and solid ground, preferably concrete.
Locate workstation in a suitable working area.
Keep the work area clean, uncluttered and ensure there is adequate lighting.
Keep the workstation clean and tidy in accordance with good workshop practice.
Keep children and unauthorised persons away from working area.
ensure that fixings have been securely tightened before use.
DO NOT use the workstation for any purpose other than that for which it is designed.
DO NOT stand on the frame or attempt to ride on it.
DO NOT attempt to transport heavy loads on the workstation.
2. INTRODUCTION
table is fully adjustable in height. Features four-section table, one large for main workpiece and three equal sized smaller sections for
accessories. rubber lining on the table helps prevent damage to the unit and workpiece. Suitable for use in workshops and warehouses.
Supplied with four castor wheels.
3. SPECIFICATION
Model No: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .AP200
minimum height: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .890mm
maximum height: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1190mm
table size (W & d): . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .730 x 505mm
capacity:. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25kg
4. ASSEMbLY
Refer to fig.1.
4.1.
Bolt front wheel frame (10) to joining frame (9). Bolt rear wheel
frame (12) to joining frame (9).
4.2.
Bolt table top base assembly (8) to joining frame (9).
4.3.
Screw wheels into the bottom of both wheel frames (10) and (12).
4.4.
Bolt table top mounting frame (6) to table top (3) using spring
washer (5) and table top mounting bolt (4). Note: table top
(3) and table top mounting frame (6) will only fit together one way.
4.5.
Insert the table top mounting frame (6) into table top base
assembly (8) so that the table top is centred directly over the
longest width of the wheels, see fig.2.
4.6.
Screw in table top adjusting screw (7).
5. OPERATION
WARNING! DO NOT extend the table beyond the extension
warning line located on the table pole.
5.1.
to adjust the height of the workstation firstly support the table
top to prevent it from dropping, then turn the adjusting screw
(7) anticlockwise to loosen it.
5.2.
When positioning the table next to or over painted or 'valuable'
surfaces ensure they are covered by protective non-scratch
covers.
fig.2
© Jack Sealey Limited
InStructIonS For:
MObILE WORKSTATION - ADJUSTAbLE HEIGHT
AP200.V2
modeL no:
fig.1
Original Language Version
AP200.V2
Issue: 2 - 03/01/17
Advertisement
Related Manuals for Sealey AP200.V2
Summary of Contents for Sealey AP200.V2
- Page 1 AP200.V2 modeL no: Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions and maintained properly, give you years of trouble free performance. IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED.
- Page 2 IMPORTANT: no liability is accepted for incorrect use of this product. WARRANTY: Guarantee is 12 months from purchase date, proof of which will be required for any claim. Sole UK Distributor, Sealey Group, www.sealey.co.uk 01284 757500 Kempson Way, Suffolk Business Park, Bury St.
- Page 3 PARTS FOR: MOBILE WORKSTATION ADJUSTABLE HEIGHT AP200. V2 MODEL: Issue: Issue Date: 261114 ITEM PART NO DESCRIPTION AP200.V2-01 RUBBER MAT (SMALL) AP200.V2-02 RUBBER MAT (LARGE) AP200.V2-03 TABLE AP200.V2-04 TABLE MOUNTING BRACKET AP200.V2-05 SPRING WASHER AP200.V2-06 TABLE MOUTING FRAME AP200.V2-07 TABLE ADJUSTING SCREW AP200.V2-08...