Advertisement
Quick Links
thank you for purchasing a sealey product. manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to
instructions
1. safety
Always load evenly with the centre of gravity of the load as near the centre and rear of the plate as possible.
9
obtain additional support for large or wide loads to prevent tipping.
9
do not overload the truck - see Specification.
8
do not leave unattended, especially when loaded, unless the wheels are chocked or the truck is otherwise secured.
8
do not use truck on uneven ground and do not run over curbs or steps - use a ramp.
8
do not allow others to ride on the truck.
8
do not use the truck if any part is damaged, paying particular attention to the
8
wheels.
2. introduction
extra strong tubular steel framework with heavy-duty pneumatic tyres allow transport
of load over rough terrain. Features foldaway toe plate and height adjustable handles.
Fitted with composite grip handles for added comfort and stability.
3. specification
model no. ........................................................... CST801
max. load ...............................................................200kg
Wheel diameter ....................................................250mm
Wheel Thickness ....................................................80mm
Height / extended ......................................810 / 1165mm
overall Width ........................................................480mm
Platform depth .....................................................290mm
4. assembly
4.1.
wheels.
4.1.1.
ensure each axle is clean from dust and dirt to allow free movement of the wheel.
4.1.2.
Slide the wheel (Fig.1.2) onto the axle (Fig.1.1), Knock the cap onto the axle using
a mallet taking care not to damage the cap (Fig.1.3)
4.1.3.
Repeat for the other side.
4.2.
toe plate .
4.2.1.
If the toe plate is not already attached, do so using the bolts, washers and
nuts supplied.
4.2.2.
Attach at the bottom of the truck as in Fig.2.1
5. operation
5.1.
Check and inflate the tyres. do not inflate above 30psi.
5.2.
Fold down the toe plate ready to accept a load. (See fig.2)
5.3.
The handle can be extended by compressing the tabs on the central bar (fig.2.2)
and pulling up on the handle. Pull upwards until a 'click' is heard.
do not overload the sack truck. do not try to carry loads that make the
truck unstable.
5.4.
Slowly lean the sack truck backwards to take the weight of the load.
5.5.
Proceed at a safe speed especially at corners where there could be a danger
of the load shifting.
5.6.
extra care should be taken on inclined surfaces.
5.7.
Where there is a curb or step, a ramp should be used.
5.8.
After use fold up the toe plate and retract the handles (Fig.2.2) store in a safe
dry place.
5.9.
Periodically check all fittings are tight.
© Jack Sealey limited
sack truck with pneumatic tyres
200kg folding
cst801
model no:
Original Language Version
fig.1
fig.2
CST801 | Issue 2 (H3F) 28/02/18
Advertisement
Related Manuals for Sealey CST801
Summary of Contents for Sealey CST801
- Page 1 IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED.
- Page 2 Parts support is available for this product. telephone 01284 757500 environment protection Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted, taken to a recycling centre and disposed of in a manner which is compatible with the environment. When the product becomes completely unserviceable and requires disposal, drain any fluids (if applicable) into approved containers and dispose of the product and fluids according to local regulations.