• Put the adapter down only on an antistatic surface such as the bag supplied in your kit. • If you are returning the adapter to Lenovo Product Support, put it back in its antistatic bag immediately. If a wrist strap is not available, ground yourself by touching the metal chassis before handling the adapter or...
Page 8
4350 Series LED locations” on page 4), and include DDR LEDs (also referred to as Flash-Based Write Cache, or FBWC, LEDs) and status LEDs. The LED states are described in Table 2 “ThinkSystem 4350 Series Status LEDs” on page 4.
Table 2. ThinkSystem 4350 Series Status LEDs (continued) Function Color AVS_ENB (DS2) Green The controller is operating normally if this LED is on or off: • On = Adaptive Voltage Scaling (AVS) Enabled • Off =Adaptive Voltage Scaling (AVS) Disabled Note: Not supported on ThinkSystem 4350-16i adapters.
Table 3. ThinkSystem 4350–8i specifications Form factor PCIe Low-profile MD2 Bus compatibility PCIe 3.0 PCIe bus width Data transfer rate 12 Gb/s per port Phys (Unified Serial Ports) Standard memory 32 MB boot flash, 256 KB SEEPROM, 128 KB MRAM Connectors, internal 1x2 mini-SAS HD x8 Maximum number of disk drivers...
Table 4. ThinkSystem 4350–16i specifications Form factor PCIe Low-profile MD2 Bus compatibility PCIe 3.0 PCIe bus width Data transfer rate 12 Gb/s per port Phys (Unified Serial Ports) Standard memory 32 MB boot flash, 128 KB SEEPROM, 128 KB MRAM Connectors, internal 4 mini-SASHD x4 Maximum number of disk drivers...
Page 12
Heat sink ThinkSystem RAID 5350–8i adapters include a passive heat sink capable of bidirectional airflow. The heat sink does not support an optional fan. The heat sink has four push-pins located at its four corners to ensure an even distribution of force across the top of the ASIC. For airflow requirements, see “Environmental specifications”...
Table 6. ThinkSystem RAID 5350–8i Status LEDs (continued) Function Color AVS_ENB (DS2) Green • On = Adaptive Voltage Scaling (AVS) enabled • Off = Adaptive Voltage Scaling (AVS) disabled PAL_DEBUG (DS10) Yellow Debug LED control signal About ThinkSystem RAID 5350–8i The ThinkSystem RAID 5350–8i is a SAS Host Bus Adapter with these features: Figure 5.
Table 7. ThinkSystem RAID 5350–8i specifications (continued) Phys (Unified Serial Ports) Standard memory 32 MB boot flash, 32 Kb SEEPROM, 128 Kb MRAM Connectors, internal 1x2 mini-SAS HD x4 Maximum number of disk drivers 4/port direct-attached (or up to 246 with expanders) Thermal sensor Inlet ambient temperature, ASIC die temperature, Top-side board ambient temperature, Bottom-side board ambient temperature...
Page 15
Heat sink ThinkSystem RAID 9350 Series adapters include a passive heat sink, which does not support an optional fan. The heat sink has four push-pins located at its four corners to ensure an even distribution of force across the top of the ASIC. For airflow requirements, see “Environmental specifications” on page 25. Visual indicators LEDs on ThinkSystem RAID 9350 Series adapters provide a visual indication for the board hardware status and cache backup system.
Page 16
Table 9. ThinkSystem RAID 9350 Series Status LEDs Function Color DDR_LED1 (DS8) Orange (8i adapters) Cache backup error Yellow (16i adapters) See Table 10 “ThinkSystem RAID 9350 Series DDR/FBWC LED states” on page 12. Dirty cache DDR_LED2 (DS9) Green See Table 10 “ThinkSystem RAID 9350 Series DDR/FBWC LED states”...
Table 11. ThinkSystem RAID 9350–8i specifications Form factor Low-profile MD2 Bus compatibility PCIe 3.0 PCIe bus width Data transfer rate 12 Gb/s per port Phys (Unified Serial Ports) Standard memory 32 MB boot flash, 256 Kb SEEPROM, 1 Mb MRAM Cache 2 GB Connectors, internal...
Page 19
Mounting bracket 4 internal mini-SAS HD connectors (CN0–CN3) UART PCIe x8 connector Super capacitor connector HDA mode jumper Note: The HDA mode jumper is only for debug purposes. It disables the firmware on the controller so that special tools can be used to remove the controller. These are only provided at the explicit direction of support.
Page 20
ThinkSystem 4350/5350/9350 Series Adapters Installation and User Guide...
To check for details, go to http://datacentersupport.lenovo.com Kit contents ThinkSystem 4350 Series kits: • ThinkSystem 4350 Series adapter • Full-height and Low-profile brackets, with mounting screws ThinkSystem RAID 5350–8i kits: • ThinkSystem RAID 5350–8i adapter • Full-height and Low-profile brackets, with mounting screws ThinkSystem RAID 9350 Series kits: •...
Step 1. Unpack the adapter in a static-free environment. Remove the adapter from the antistatic bag, and carefully inspect for damage. If damage is noticed, contact Lenovo or your reseller support representative. Attention: To avoid the risk of data loss, back up your data before you change your system configuration.
Page 23
Note: For ThinkSystem RAID 9350 Series adapters, choose a slot within reach of an empty SuperCap module retention mechanisim. For more details about the mechanism, see the hardware documentation of your system. CAUTION: Touch a grounded metal object before handling the adapter. Be sure to handle the adapter by its bracket or edges only.
Figure 11. Connecting cables between the adapter and storage devices Step 7. Replace the cover and reconnect any cords and cables, and power up the system. Replace the chassis’s cover, reconnect any power cords, and reconnect network cables. Turn on the power. Step 8.
Installing device driver This adapter can operate under various operating systems; however, you must install appropriate software drivers. The firmware and device drivers are routinely updated and are made available on the Lenovo Support web site. Refer to for details on the software versions and http://datacentersupport.lenovo.com...
Page 26
ThinkSystem 4350/5350/9350 Series Adapters Installation and User Guide...
200 LFW (linear feet per minute), minimum. Ambient temperature with forced airflow 0°C to 55°C Relative humidity • ThinkSystem 4350 Series: 10% to 90%, non-condensing • ThinkSystem RAID 5350/9350 Series: 20% to 80%, non-condensing Altitude Up to 3000 meters...
Page 30
ThinkSystem 4350/5350/9350 Series Adapters Installation and User Guide...
Gathering information needed to call Support If you require warranty service for your Lenovo product, the service technicians will be able to assist you more efficiently if you prepare the appropriate information before you call. You can also go to http:// for more information about your product warranty.
Electronic Service Request. Submitting an Electronic Service Request will start the process of determining a solution to your problem by making the pertinent information available to the service technicians. The Lenovo service technicians can start working on your solution as soon as you have completed and submitted an Electronic Service Request.
Lenovo representative for information on the products and services currently available in your area. Any reference to a Lenovo product, program, or service is not intended to state or imply that only that Lenovo product, program, or service may be used. Any functionally equivalent product, program, or service that does not infringe any Lenovo intellectual property right may be used instead.
This product may not be certified in your country for connection by any means whatsoever to interfaces of public telecommunications networks. Further certification may be required by law prior to making any such connection. Contact a Lenovo representative or reseller for any questions. Electronic emission notices When you attach a monitor to the equipment, you must use the designated monitor cable and any interference suppression devices that are supplied with the monitor.