• The product-specific section includes service, reference, and product-specific parts information. Important: This manual is intended only for trained servicers who are familiar with Lenovo products. Use this manual to troubleshoot problems effectively. Before servicing a Lenovo product, make sure to read all the information under “Safety information” on page 1 and “Important service information” on page 16.
Safety information Safety information This chapter presents the following safety information that you need to get familiar with before you service a Lenovo V310-14ISK/Lenovo V310-15ISK computer: • “General safety” on page 2 • “Electrical safety” on page 3 • “Safety inspection guide” on page 5 • “Handling devices that are sensitive to electrostatic discharge” on page 6 • “Grounding requirements” on page 6 • “Safety notices: multilingual translations” on page 7 • “Laser compliance statement” on page 14...
Lenovo V310-14ISK/Lenovo V310-15ISK Hardware Maintenance Manual General safety Follow these rules below to ensure general safety: • Observe a good housekeeping in the area where the machines are put during and after the maintenance. • When lifting any heavy object: 1. Make sure that you can stand safely without slipping. 2. Distribute the weight of the object equally between your feet. 3. Use a slow lifting force. Never move suddenly or twist when you attempt to lift it. 4. Lift it by standing or pushing up with your leg muscles; this action could avoid the strain from the muscles in your back. Do not attempt to lift any object that weighs more than 16 kg (35 lb) or that you think is too heavy for you. • Do not perform any action that causes hazards to the customer, or that makes the machine unsafe.
Safety information Electrical safety Observe the following rules when working on electrical equipments. Important: Use only approved tools and test equipments. Some hand tools have handles covered with a soft material that does not insulate you when working with live electrical currents. Many customers have rubber floor mats near their machines that contain small conductive fibers to decrease electrostatic discharges.
Page 8
Lenovo V310-14ISK/Lenovo V310-15ISK Hardware Maintenance Manual • Always look carefully for possible hazards in your work area. Examples of these hazards are moist floors, nongrounded power extension cables, power surges, and missing safety grounds. • Do not touch live electrical circuits with the reflective surface of a plastic dental mirror. The surface is conductive; such touching can cause personal injury and machine damage. • Do not service the following parts with the power on when they are removed from their normal operating places in a machine: – Power supply units – Pumps – Blowers and fans – Motor generators and similar units. (This practice ensures correct grounding of the units.) • If an electrical accident occurs: – Caution: do not become a victim yourself.
The power cord should be the type specified in the parts list. c. Insulation must not be frayed or worn. 4. Check for cracked or bulging batteries. 5. Remove the cover. 6. Check for any obvious non-Lenovo alterations. Use good judgment as to the safety of any non-Lenovo alterations. 7. Check inside the unit for any obvious unsafe conditions, such as metal filings, contamination, water or other liquids, or signs of fire or smoke damage. 8. Check for worn, frayed, or pinched cables.
Lenovo V310-14ISK/Lenovo V310-15ISK Hardware Maintenance Manual Handling devices that are sensitive to electrostatic discharge Any computer part containing transistors or integrated circuits (ICs) should be considered sensitive to electrostatic discharge (ESD). ESD damage can occur when there is a difference in charge between objects. Protect against ESD damage by equalizing the charge so that the machine, the part, the work mat, and the person handling the part are all at the same charge. Notes: 1. Use product-specific ESD procedures when they exceed the requirements noted here.
Safety information Safety notices: multilingual translations The safety notices in this section are provided in English, French, German, Hebrew, Italian, Japanese, and Spanish. Safety notice 1 Before the computer is powered on after FRU replacement, make sure all screws, springs, and other small parts are in place and are not left loose inside the computer.
Page 12
Lenovo V310-14ISK/Lenovo V310-15ISK Hardware Maintenance Manual Safety notice 2 DANGER Some standby batteries contain a small amount of nickel and cadmium. Do not disassemble a standby battery, recharge it, throw it into fire or water, or short- circuit it. Dispose of the battery as required by local ordinances or regulations.
Page 13
Safety information Safety notice 3 DANGER The battery pack contains small amounts of nickel. Do not disassemble it, throw it into fire or water, or short-circuit it. Dispose of the battery pack as required by local ordinances or regulations. Use only the battery in the appropriate parts listing when replacing the battery pack.
Page 14
Lenovo V310-14ISK/Lenovo V310-15ISK Hardware Maintenance Manual Safety notice 4 DANGER The lithium battery can cause a fire, an explosion, or a severe burn. Do not recharge it, remove its polarized connector, disassemble it, heat it above 100°C (212°F), incinerate it, or expose its cell contents to water. Dispose of the battery as required by local ordinances or regulations.
Page 15
Safety information Safety notice 5 If the LCD breaks and the fluid from inside the LCD gets into your eyes or on your hands, immediately wash the affected areas with water at least for 15 minutes. Seek medical care if any symptoms caused by the fluid are present after washing. Si le panneau d’affichage à...
Page 16
Lenovo V310-14ISK/Lenovo V310-15ISK Hardware Maintenance Manual Safety notice 6 DANGER To avoid shock, do not remove the plastic cover that protects the lower part of the inverter card. Afin d’éviter tout risque de choc électrique, ne retirez pas le cache en plastique protégeant la partie inférieure de la carte d’alimentation.
Page 17
Safety information Safety notice 8 DANGER Before removing any FRU, turn off the computer, unplug all power cords from electrical outlets, remove the battery pack, and then disconnect any interconnecting cables. Avant de retirer une unité remplaçable en clientèle, mettez le système hors tension, débranchez tous les cordons d’alimentation des socles de prise de courant, retirez la batterie et déconnectez tous les cordons d’interface.
Lenovo V310-14ISK/Lenovo V310-15ISK Hardware Maintenance Manual Laser compliance statement Some models of Lenovo computer are equipped from the factory with an optical storage device such as a CD-ROM drive or a DVD-ROM drive. Such devices are also sold separately as options. If one of these drives is installed, it is certified in the U.S. to conform to the requirements of the Department of Health and Human Services 21 Code of Federal Regulations (DHHS 21 CFR) Subchapter J for Class 1 laser products. Elsewhere, the drive is certified to conform to the requirements of the International Electrotechnical Commission (IEC) 825 and CENELEC EN 60 825 for Class 1 laser products.
Page 19
Safety information A CD-ROM drive, a DVD-ROM drive, or any other storage device installed may contain an embedded Class 3A or Class 3B laser diode. Note the following: DANGER Emits visible and invisible laser radiation when open. Do not stare into the beam, do not view directly with optical instruments, and avoid direct exposure to the beam. Radiação por raio laser ao abrir. Não olhe fixo no feixe de luz, não olhe diretamente por meio de instrumentos óticos e evite exposição direta com o feixe de luz.
Strategy for replacing FRUs Before replacing parts: Make sure that all software fixes, drivers, and BIOS downloads are installed before replacing any FRUs listed in this manual. After a system board is replaced, ensure that the latest BIOS is loaded to the system board before completing the service action. To download software fixes, drivers, and BIOS, follow the steps below: 1. Go to http://support.lenovo.com. 2. Enter the serial number or select a product or use Lenovo smart downloading. 3. Select the BIOS/Driver/Applications and download. 4. Follow the directions on the screen and install the necessary software.
Important service information Use the following strategy to prevent unnecessary expense for replacing and servicing FRUs: • If you are instructed to replace an FRU, but the replacement does not solve the problem, reinstall the original FRU before you continue. • Some computers have both a processor board and a system board. If you are instructed to replace either of them, and replacing one of them does not solve the problem, reinstall that board, and then replace the other one. • If an adapter or a device consists of more than one FRU, any of the FRUs may be the cause of the error. Before replacing the adapter or device, remove the FRUs one by one to see if the symptoms change. Replace only the FRU that changed the symptoms. Attention: The setup configuration on the computer you are servicing may have been customized. Running Automatic Configuration may alter the settings. Note the current configuration settings (using the View Configuration option); then, when service has been completed, verify that those settings remain in effect.
Note: RoHS and non-RoHS FRU part numbers with the same fit and function are identified with unique FRU part numbers. Lenovo plans to transit to RoHS compliance well before the implementation date and expects its suppliers to be ready to support Lenovo’s requirements and schedule in the EU. Products sold in 2005 and 2006 will contain some RoHS compliant FRUs. The following statement pertains to these products and any product Lenovo produces containing RoHS compliant FRUs.
General checkout General checkout This chapter presents the following information: • “What to do first” on page 20 • “Power system checkout” on page 21 Before you go to the checkout, make sure to read the following important notes: Important notes: • Only certified trained personnel can service the computer. • Before replacing any FRU, read the entire page on removing and replacing FRUs. • Carefully remove screws for reuse when replacing FRUs. • Be extremely careful during such write operations as copying, saving, or formatting. Drives in the computer that you are servicing sequence might have been altered.
Lenovo V310-14ISK/Lenovo V310-15ISK Hardware Maintenance Manual What to do first When you do return an FRU, you must include the following information in the parts exchange form or parts return form that you attach to it: 1. Name and phone number of servicer 2. Date of service 3. Date on which the machine failed 4. Date of purchase 5. Procedure index and page number in which the failing FRU was detected 6. Failing FRU name and part number 7. Machine type, model number, and serial number 8. Customer’s name and address Note for warranty: During the warranty period, the customer may be responsible for repair costs if the computer damage was caused by misuse, accident, modification, unsuitable physical or operating environment, or improper maintenance by the customer.
• If the computer does not charge during operation, go to “Checking operational charging”. To check the AC adapter, follow the steps below: 1. Unplug the AC adapter cable from the computer. 2. Measure the output voltage at the plug of the AC adapter cable. See the following figure: Voltage (V DC) Note: Output voltage for the AC adapter pin No. 2 may differ from the one you are servicing. 3. If the voltage is not correct, replace the AC adapter. 4. If the voltage is acceptable, do the following: • Replace the system board. • If the problem persists, go to “Lenovo V310-14ISK/Lenovo V310-15ISK” on page 26. Note: Noise from the AC adapter does not always indicate a defect.
Lenovo V310-14ISK/Lenovo V310-15ISK Hardware Maintenance Manual Checking operational charging To check whether the battery charges properly during operation, use a discharged battery pack or a battery pack that has less than 50% of the total power remaining when installed in the computer. Perform operational charging. If the battery status indicator or icon does not light on, remove the battery pack and let it return to room temperature. Reinstall the battery pack. If the charge indicator or icon is still off, replace the battery pack. If the charge indicator still does not light on, replace the system board. Then reinstall the battery pack. If it is still not charged, go to the next section. Checking the battery pack Battery charging does not start until the Power Meter shows that less than 95% of the total power remains; under this condition the battery pack can charge to...
System and run System Recovery. For details of OneKey Recovery System, see the User Guide for Lenovo OneKey Recovery System . Note: This will delete all the new data on the system partition (C drive), which is not recoverable. Make sure to back up your critical data before you perform this...
Lenovo V310-14ISK/Lenovo V310-15ISK Hardware Maintenance Manual Passwords As many as three passwords may be needed for any Lenovo computer: the power-on password (POP), the hard disk password (HDP), and the administrator password. If any of these passwords has been set, a prompt for it appears on the screen whenever the computer is turned on. The computer does not start until the password is entered.
Related service information Power management Note: Power management modes are not supported for APM operating system. When you have finished working with your computer, you can set it to shut down, sleep or hibernate. Putting the computer to sleep or shutting it down When you have finished working with your computer, you can put it to sleep or shut it down. Putting your computer to sleep If you will be away from your computer for only a short time, put the computer to sleep. When the computer is in sleep mode, you can quickly wake it to resume use, bypassing the startup process. To put the computer to sleep, do one of the following: • Close the display lid.
Lenovo V310-14ISK/Lenovo V310-15ISK Hardware Maintenance Manual Lenovo V310-14ISK/Lenovo V310-15ISK This chapter presents the following product-specific service references and product-specific parts information: • “Specifications” on page 26 • “Status indicators” on page 28 • “Fn key combinations/Hotkeys” on page 29 • “FRU replacement notices” on page 30 • “Removing and replacing an FRU” on page 31 • “Locations” on page 71 • “Parts list” on page 75 Specifications The following table lists the specifications of the Lenovo V310-14ISK/ Lenovo V310-15ISK: Table 1. Specifications Feature...
Page 31
Lenovo V310-14ISK/Lenovo V310-15ISK Table 1. Specifications (continued) Feature Description I/O port • USB 2.0 × 1, USB 3.0 × 2 • Combo audio jack × 1 • VGA × 1 • HDMI port × 1 • RJ-45 × 1 (1000 Mbps) • Memory card slot (SD/SDHC/SDXC/MMC) Audio • 1/8" Combo audio jack • 1.5 W speaker × 2 • Digita microphone, combo with camera (on select models) Ethernet • 1000 Mbps Bluetooth • Combined in combo card wireless Keyboard • 6 rows Lenovo Keyboard Touchpad • Multi-touch touchpad...
Lenovo V310-14ISK/Lenovo V310-15ISK Hardware Maintenance Manual Status indicators The system status indicators below show the computer status: Table 2. Status indicators Indicator Charge Indicator Meaning status status Charging The battery has more than 80% charge. On (solid green) Discharging The battery has more than 20% charge. On (solid The battery has between 5% and 20% Discharging amber) charge. The battery has between 20% and 80% Blinking charge. When the battery reaches 80% charge, slowly Charging the light will stop blinking. However, charging (green) Battery status will continue until the battery is fully charged. indicator Blinking The battery has less than 20% charge.
Lenovo V310-14ISK/Lenovo V310-15ISK Fn key combinations/Hotkeys The following table shows the function of each combination of Fn with a function key. Table 3. Fn key combinations Fn + B: Activates the break function. Fn + P: Activates the pause function. Fn + C: Enables/disables the scroll lock. Fn + S: Activates the system request.
Hardware Maintenance Manual FRU replacement notices This section presents notices related to removing and replacing parts. Read this section carefully before replacing any FRU. Screw notices Loose screws can cause a reliability problem. In the Lenovo computer, this problem is addressed with special nylon-coated screws that have the following characteristics: • They maintain tight connections. • They do not easily come loose, even with shock or vibration. • They are harder to tighten.
Attention: The system board is sensitive to, and can be damaged by, electrostatic discharge. Before touching it, establish personal grounding by touching a ground point with one hand or using an electrostatic discharge (ESD) strap (P/N 6405959) to remove potential shock reasons. Notes: • This manual applies to the following models: Lenovo V310-14ISK/ Lenovo V310-15ISK. • The illustrations used in this manual are for Lenovo V310-15ISK unless otherwise stated.
Lenovo V310-14ISK/Lenovo V310-15ISK Hardware Maintenance Manual 1010 Removable module (on select models) Attention: To protect your HDD, please do not swap between ODD and 2nd battery when system is running. Figure 1. Removal steps of removable module (on select models) Note: Some models are supplied with an optical disk drive or a removable battery as an optional module. For example purposes, this section describes the replacement of the optical disk drive module.
Page 37
Lenovo V310-14ISK/Lenovo V310-15ISK Figure 1. Removal steps of removable module (on select models) (continued) Remove the screw 3, then carefully remove the removable module bracket and bezel in the directions shown by arrows 4 and 5. Step Screw (quantity) Color Torque M2 × 2.5 mm, Phillips head, nylok-coated (1) Black 1.85±0.15 kgf*cm ODD BKT → ODD...
Page 38
Lenovo V310-14ISK/Lenovo V310-15ISK Hardware Maintenance Manual Figure 1. Removal steps of removable module (on select models) (continued) Supplied with an optical disk drive and a removable battery Hold the spring-loaded latch in the unlocked position 1. Gently pull the removable module out 2. Remove the screw 3, then carefully remove the removable module latch catch and bezel in the directions shown by arrows 4 and 5. Step Screw (quantity) Color Torque M2 × 2.5 mm, Phillips head, nylok-coated (1) Black 1.85±0.15 kgf*cm ODD BKT → ODD...
Lenovo V310-14ISK/Lenovo V310-15ISK 1020 Base cover For access, remove this FRU: • “1010 Removable module (on select models)” on page 32 Figure 2. Removal steps of base cover Supplied with an optical disk drive Or a removable battery Remove the screws 1 and 2 from the bottom. Step Screw (quantity) Color Torque M2 × 5.5 mm, Phillips head, nylok-coated (10) Black 1.85±0.15 kgf*cm D cover → C cover M2 × 1.5 mm, Phillips head, nylok-coated (3) Black 1.85±0.15 kgf*cm D cover → C cover (ODD location)
Page 40
Lenovo V310-14ISK/Lenovo V310-15ISK Hardware Maintenance Manual Figure 2. Removal steps of base cover (continued) Use a plastic prying tool to aid in separation, then remove the base cover in the direction shown by arrow 3.
Page 41
Lenovo V310-14ISK/Lenovo V310-15ISK Figure 2. Removal steps of base cover (continued) Supplied with an optical disk drive and a removable battery Remove the screws 1 and 2 from the bottom. Step Screw (quantity) Color Torque M2 × 5.5 mm, Phillips head, nylok-coated (11) D Black 1.85±0.15 kgf*cm cover → C cover M2 × 1.5 mm, Phillips head, nylok-coated (3) Black 1.85±0.15 kgf*cm D cover → C cover (ODD location) Use a plastic prying tool to aid in separation, then remove the base cover in the direction shown by arrow 3.
Page 42
Lenovo V310-14ISK/Lenovo V310-15ISK Hardware Maintenance Manual Note: Applying labels to the base cover The new base cover FRU is shipped with a kit containing labels of several kinds. When you replace the base cover, you need to apply the following labels: The following labels need to be peeled off from the old base cover, and need to be put on the new base cover. Rating label Indonesia rating label Rating print label Israel label Malaysia label KCC label SIRIM label Brazil label Wlan Indonesia label ARG label For some models, you also need to apply one or two FCC labels. Check the...
Lenovo V310-14ISK/Lenovo V310-15ISK 1030 Battery pack For access, remove these FRUs in order: • “1010 Removable module (on select models)” on page 32 • “1020 Base cover” on page 35 DANGER Only use the battery specified in the parts list for your computer. Any other battery could ignite or explode. Figure 3. Removal steps of battery pack Detach the battery pack connector in the direction shown by arrow 1. Remove the battery pack in the direction shown by arrow 2.
Lenovo V310-14ISK/Lenovo V310-15ISK Hardware Maintenance Manual 1040 Hard disk drive For access, remove these FRUs in order: • “1010 Removable module (on select models)” on page 32 • “1020 Base cover” on page 35 • “1030 Battery pack” on page 39 Attention: • Do not drop the hard disk drive or apply any physical shock to it. The hard disk drive is sensitive to physical shock. Improper handling can cause damage and permanent loss of data. • Before removing the drive, suggest the customer to backup all the information on it if possible.
Page 45
Lenovo V310-14ISK/Lenovo V310-15ISK Figure 4. Removal steps of hard disk drive (continued) Remove the screws 3, and then take out the metal frame. Step Screw (quantity) Color Torque M3 × 3 mm, Phillips head, nylok-coated (4) Silver 3.0±0.3 kgf*cm HDD → HDD bracket...
Lenovo V310-14ISK/Lenovo V310-15ISK Hardware Maintenance Manual 1050 PCI Express Mini Card for wireless LAN For access, remove these FRUs in order: • “1010 Removable module (on select models)” on page 32 • “1020 Base cover” on page 35 • “1030 Battery pack” on page 39 Important: The preinstalled WLAN module may only be replaced with a Lenovo approved module in order to comply with FCC and IC regulations. Refer to “Table 5. Parts list—Overall” on page 78 for Lenovo part numbers for the approved modules. Figure 5. Removal steps of PCI Express Mini Card for wireless LAN Disconnect the two wireless LAN cables (black, white) 1, and then remove the screw 2. In step 1, unplug the jacks by using the removal tool antenna RF connector (P/N: 08K7159), or pick up the connectors with your fingers and gently unplug them in the direction shown by the arrows.
Page 47
Lenovo V310-14ISK/Lenovo V310-15ISK Figure 5. Removal steps of PCI Express Mini Card for wireless LAN (continued) Remove the card in the direction shown by arrow 3. When installing: • In models with a wireless LAN card that has two antenna connectors, plug the black cable (1st) (MAIN) into the jack labeled MAIN, and the white cable (2nd) (AUX) into the jack labeled AUX on the card. • In models with a wireless LAN card that has three antenna connectors, plug the black cable (1st) (MAIN) into the jack labeled 1, the grey cable (3rd) into the jack labeled 3, and the white cable (2nd) (AUX) into the jack labeled 2 on the card.
Lenovo V310-14ISK/Lenovo V310-15ISK Hardware Maintenance Manual 1060 DIMM For access, remove these FRUs in order: • “1010 Removable module (on select models)” on page 32 • “1020 Base cover” on page 35 • “1030 Battery pack” on page 39 Figure 6. Removal steps of DIMM Release the two latches on both edges of the socket at the same time in the directions shown by arrows 1, and then unplug the DIMM in the direction shown by arrow 2. When installing: Insert the notched end of the DIMM into the socket. Push the DIMM firmly, and pivot it until it snaps into place. Make sure that it is firmly fixed in the slot and is difficult to move. Note: When replacing the memory is completed, you need to restart the...
Lenovo V310-14ISK/Lenovo V310-15ISK 1070 ODD Board and 2nd battery board (Lenovo V310-15ISK) For access, remove these FRUs in order: • “1010 Removable module (on select models)” on page 32 • “1020 Base cover” on page 35 • “1030 Battery pack” on page 39 Figure 7. Removal steps of ODD Board and 2nd battery board (Lenovo V310-15ISK) Detach the ODD board connector in the directions shown by arrows 1 and 2. Remove the screws 3. Step Screw (quantity) Color Torque M2 × 3 mm, Phillips head, nylok-coated (2) Black 1.85±0.15 kgf*cm...
Page 50
Lenovo V310-14ISK/Lenovo V310-15ISK Hardware Maintenance Manual Figure 7. Removal steps of ODD Board and 2nd battery board (Lenovo V310- 15ISK) (continued) Remove the screws 5. Step Screw (quantity) Color Torque M2 × 3 mm, Phillips head, nylok-coated (3) Black 1.85±0.15 kgf*cm 2nd battery convert BD → C cover Remove the 2nd battery board 6.
Lenovo V310-14ISK/Lenovo V310-15ISK 1080 USB board and fingerprint reader module For access, remove these FRUs in order: • “1010 Removable module (on select models)” on page 32 • “1020 Base cover” on page 35 • “1030 Battery pack” on page 39 • “1040 Hard disk drive” on page 40 Figure 8. Removal steps of USB Board and fingerprint reader module Detach the USB board connector in the directions shown by arrows 1 and 2. Peel off the foil stuck on the USB board cable 3. Remove the screws 4. Step Screw (quantity) Color Torque M2 × 3 mm, Phillips head, nylok-coated (2) Black 1.85±0.15 kgf*cm USB BD → C cover...
Page 52
Lenovo V310-14ISK/Lenovo V310-15ISK Hardware Maintenance Manual Figure 8. Removal steps of USB Board and fingerprint reader module (continued) Detach the fingerprint reader connector in the directions shown by arrows 6 and 7. Remove the screws 8. Lenovo V310-14ISK Lenovo V310-15ISK Step Screw (quantity) Color Torque M2 × 3 mm, Phillips head, nylok-coated (1) Black 1.85±0.15 kgf*cm FP BD → C cover...
Page 53
Lenovo V310-14ISK/Lenovo V310-15ISK Figure 8. Removal steps of USB Board and fingerprint reader module (continued) Remove the fingerprint reader module 9. Lenovo V310-14ISK Lenovo V310-15ISK...
Lenovo V310-14ISK/Lenovo V310-15ISK Hardware Maintenance Manual 1090 Fan and heat sink assembly For access, remove these FRUs in order: • “1010 Removable module (on select models)” on page 32 • “1020 Base cover” on page 35 • “1030 Battery pack” on page 39 • “1040 Hard disk drive” on page 40 • “1050 PCI Express Mini Card for wireless LAN” on page 42 • “1070 ODD Board and 2nd battery board (Lenovo V310-15ISK)” on page 45 • “1080 USB board and fingerprint reader module” on page 47 Figure 9. Removal steps of heat sink assembly Unplug the fan connector in the direction shown by arrow 1. Remove the screws 2.
Page 55
Lenovo V310-14ISK/Lenovo V310-15ISK Figure 9. Removal steps of heat sink assembly Lift the fan and the heat sink in the direction shown by arrows 3. When installing: Before you attach the fan assembly to the computer, apply thermal grease, at an amount of 0.2 grams, to the and part shown in the figure above. Either too much or too little grease application can cause a thermal problem due to imperfect contact with a component.
Lenovo V310-14ISK/Lenovo V310-15ISK Hardware Maintenance Manual 1100 System board Important notices for handling the system board: When handling the system board, bear the following in mind. • Be careful not to drop the system board on a bench top that has a hard surface, such as metal, wood, or composite.
Page 57
Lenovo V310-14ISK/Lenovo V310-15ISK Figure 10. Removal steps of system board (continued) Detach the seven connectors in the directions shown by arrows 1, 2 and 3. Lenovo V310-14ISK Lenovo V310-15ISK...
Page 58
Lenovo V310-14ISK/Lenovo V310-15ISK Hardware Maintenance Manual Figure 10. Removal steps of system board (continued) Remove the screws 4. Lenovo V310-14ISK Lenovo V310-15ISK Step Screw (quantity) Color Torque M2 × 3 mm, Phillips head, nylok-coated (7) Black 1.85±0.15 kgf*cm (Lenovo V310-14ISK) MB → C cover M2 × 3.5 mm, Phillips head, nylok-coated (6) Black 1.85±0.15 kgf*cm (Lenovo V310-15ISK) MB → C cover & DC-IN CONN → C cover When installing: Make sure that the connectors are attached firmly.
Page 59
Lenovo V310-14ISK/Lenovo V310-15ISK Figure 10. Removal steps of system board (continued) Carefully turn the main board over 5. Disconnect the keyboard connector in the directions shown by arrows 6 and 7. Then remove the main board. Lenovo V310-14ISK Lenovo V310-15ISK Remove the RTC battery with a prying tool 8.
Lenovo V310-14ISK/Lenovo V310-15ISK Hardware Maintenance Manual 1110 Speaker For access, remove these FRUs in order: • “1010 Removable module (on select models)” on page 32 • “1020 Base cover” on page 35 • “1030 Battery pack” on page 39 • “1040 Hard disk drive” on page 40 • “1050 PCI Express Mini Card for wireless LAN” on page 42 • “1070 ODD Board and 2nd battery board (Lenovo V310-15ISK)” on page 45 • “1080 USB board and fingerprint reader module” on page 47 • “1090 Fan and heat sink assembly” on page 50 • “1100 System board” on page 52 Figure 11. Removal steps of speaker Remove the speaker 1.
Lenovo V310-14ISK/Lenovo V310-15ISK 1120 Power board and LED board (Lenovo V310-15ISK) For access, remove these FRUs in order: • “1010 Removable module (on select models)” on page 32 • “1020 Base cover” on page 35 • “1030 Battery pack” on page 39 • “1040 Hard disk drive” on page 40 • “1050 PCI Express Mini Card for wireless LAN” on page 42 • “1070 ODD Board and 2nd battery board (Lenovo V310-15ISK)” on page 45 • “1080 USB board and fingerprint reader module” on page 47 • “1090 Fan and heat sink assembly” on page 50 • “1100 System board” on page 52 • “1110 Speaker” on page 56 Figure 12. Removal steps of power board and LED board Remove the screws 1, then remove the power board in the direction shown by arrow 2.
Page 62
Lenovo V310-14ISK/Lenovo V310-15ISK Hardware Maintenance Manual Figure 12. Removal steps of power board and LED board (continued) Remove the screws 3, then remove the LED board in the direction shown by arrow 4. Step Screw (quantity) Color Torque M2 × 3 mm, Phillips head, nylok-coated (1) Black 1.85±0.15 kgf*cm LED BD → C cover...
Lenovo V310-14ISK/Lenovo V310-15ISK 1130 Upper case For access, remove these FRUs in order: • “1010 Removable module (on select models)” on page 32 • “1020 Base cover” on page 35 • “1030 Battery pack” on page 39 • “1040 Hard disk drive” on page 40 • “1050 PCI Express Mini Card for wireless LAN” on page 42 • “1070 ODD Board and 2nd battery board (Lenovo V310-15ISK)” on page 45 • “1080 USB board and fingerprint reader module” on page 47 • “1090 Fan and heat sink assembly” on page 50 • “1100 System board” on page 52 • “1110 Speaker” on page 56 • “1120 Power board and LED board (Lenovo V310-15ISK)” on page 57...
Page 64
Lenovo V310-14ISK/Lenovo V310-15ISK Hardware Maintenance Manual Figure 13. Removal steps of upper case Remove the screws . Release the LCD cable and antenna cables from the cable guides. Lenovo V310-14ISK Lenovo V310-15ISK Step Screw (quantity) Color Torque M2.5 × 5 mm, Phillips head, nylok-coated (3) Silver 3.0±0.3 kgf*cm (Lenovo V310-14ISK) Hinge → C cover Silver M2.5 × 5 mm, Phillips head, nylok-coated (4) 3.0±0.3 kgf*cm (Lenovo V310-15ISK) Hinge → C cover M2 × 2 mm, Phillips head, nylok-coated (3) Black 1.85±0.15 kgf*cm (Lenovo V310-14ISK) Hinge → C cover...
Page 65
Lenovo V310-14ISK/Lenovo V310-15ISK Figure 13. Removal steps of upper case (continued) Open the hinge in the direction shown by arrows 2. Lenovo V310-14ISK Lenovo V310-15ISK...
Page 66
Lenovo V310-14ISK/Lenovo V310-15ISK Hardware Maintenance Manual Figure 13. Removal steps of upper case (continued) Remove the upper case from LCD unit in the direction shown by arrow 3. Lenovo V310-14ISK Lenovo V310-15ISK...
Page 67
Lenovo V310-14ISK/Lenovo V310-15ISK Figure 13. Removal steps of upper case (continued) Remove the DC-in cable in the direction shown by arrow 4. Lenovo V310-14ISK Lenovo V310-15ISK...
Page 68
Lenovo V310-14ISK/Lenovo V310-15ISK Hardware Maintenance Manual Figure 13. Removal steps of upper case (continued) Lenovo V310-14ISK: Remove the screw 5, then remove the power board 6. Step Screw (quantity) Color Torque M2 × 3 mm, Phillips head, nylok-coated (1) Black 1.85±0.15 kgf*cm (Lenovo V310-14ISK) power BD → C cover...
Lenovo V310-14ISK/Lenovo V310-15ISK 1140 LCD unit For access, remove these FRUs in order: • “1010 Removable module (on select models)” on page 32 • “1020 Base cover” on page 35 • “1030 Battery pack” on page 39 • “1040 Hard disk drive” on page 40 • “1050 PCI Express Mini Card for wireless LAN” on page 42 • “1070 ODD Board and 2nd battery board (Lenovo V310-15ISK)” on page 45 • “1080 USB board and fingerprint reader module” on page 47 • “1100 System board” on page 52 Figure 14. Removal steps of LCD unit Remove the LCD front bezel in the direction shown by arrows 1.
Page 70
Lenovo V310-14ISK/Lenovo V310-15ISK Hardware Maintenance Manual Figure 14. Removal steps of LCD unit (continued) Remove the screws 2. Lift the LCD panel slightly 3. Peel off the adhesive tape and detach the connector in the direction shown by arrow 4. Then remove the LCD panel.
Lenovo V310-14ISK/Lenovo V310-15ISK 1150 LCD hinges For access, remove these FRUs in order: • “1010 Removable module (on select models)” on page 32 • “1020 Base cover” on page 35 • “1030 Battery pack” on page 39 • “1040 Hard disk drive” on page 40 • “1050 PCI Express Mini Card for wireless LAN” on page 42 • “1070 ODD Board and 2nd battery board (Lenovo V310-15ISK)” on page 45 • “1080 USB board and fingerprint reader module” on page 47 • “1090 Fan and heat sink assembly” on page 50 • “1100 System board” on page 52 • “1110 Speaker” on page 56 • “1120 Power board and LED board (Lenovo V310-15ISK)” on page 57 • “1130 Upper case” on page 59 • “1140 LCD unit” on page 65 Figure 15. Removal steps of LCD hinges Remove the screws 1.
Page 72
Lenovo V310-14ISK/Lenovo V310-15ISK Hardware Maintenance Manual Figure 15. Removal steps of LCD hinges (continued) Release the two hinges in the direction shown by arrows 2.
Lenovo V310-14ISK/Lenovo V310-15ISK 1160 EDP cable and integrated camera For access, remove these FRUs in order: • “1010 Removable module (on select models)” on page 32 • “1020 Base cover” on page 35 • “1030 Battery pack” on page 39 • “1040 Hard disk drive” on page 40 • “1050 PCI Express Mini Card for wireless LAN” on page 42 • “1070 ODD Board and 2nd battery board (Lenovo V310-15ISK)” on page 45 • “1080 USB board and fingerprint reader module” on page 47 • “1090 Fan and heat sink assembly” on page 50 • “1100 System board” on page 52 • “1110 Speaker” on page 56 • “1120 Power board and LED board (Lenovo V310-15ISK)” on page 57 • “1130 Upper case” on page 59 • “1140 LCD unit” on page 65 • “1150 LCD hinges” on page 67 Figure 16. Removal steps of EDP cable and integrated camera Note: The integrated camera is stuck on the top center of the LCD cover.
Page 74
Lenovo V310-14ISK/Lenovo V310-15ISK Hardware Maintenance Manual Figure 16. Removal steps of EDP cable and integrated camera (continued) Peel off the foil and tape secure the EDP cable in the direction shown by arrows 3. Remove the EDP cable in the direction shown by arrows 4.
Lenovo V310-14ISK/Lenovo V310-15ISK Locations Front and right-side view 1 Integrated camera (on select models) 2 Built-in microphone 3 Wireless LAN antennas 4 Computer display 5 Power button 6 Touchpad 7 Fingerprint reader (on select models) 8 Novo button 9 Combo audio jack j USB port k Kensington mini security slot l Optional module (Optical disk drive/removable battery) (on select models) m Power status indicator Note: For the description of each indicator, see “Status indicators” on page 28. n AC power adapter jack Lenovo V310-14ISK...
Lenovo V310-14ISK/Lenovo V310-15ISK Bottom and left-side view 1 Speakers 2 Louvers 3 System status indicators Note: For the description of each indicator, see “Status indicators” on page 28. 4 Memory card slot 5 USB ports 6 HDMI port 7 RJ-45 port 8 VGA port 9 Ventilation slots J Power status indicator Note: For the description of each indicator, see “Status indicators” on page 28. K AC power adapter jack L Lenovo OneLink connector (on select models) M Kensington mini security slot N Optical disk drive/removable battery latch (on select models) Lenovo V310-14ISK...
Lenovo V310-14ISK/Lenovo V310-15ISK Parts list This section presents the following service parts: • “Overall” on page 76 • “LCD FRUs” on page 93 • “Miscellaneous parts” on page 96 • “AC adapters” on page 96 • “Screws” on page 96 Note: Each FRU is available for all types or models, unless specific types or models are specified. Attention: Do not attempt to replace an FRU on your own. If an FRU is damaged, contact a Lenovo authorized servicer or a marketing representative for replacement or repair. Only qualified technicians can inspect or repair this product.
Page 82
Lenovo V310-14ISK/Lenovo V310-15ISK Hardware Maintenance Manual Table 5. Parts list—Overall Lenovo Lenovo No. FRU FRU no. V310-14ISK V310-15ISK a-g See “Miscellaneous parts” on page 96. LCD unit (see “LCD FRUs” on page 93.) Upper Case Q 80SX FP W/KB US 5CB0L46648 ● Upper Case Q 80SX NFP W/KB US 5CB0L46554 ● Upper Case Q 80SX FP W/KB UK 5CB0L46597 ● Upper Case Q 80SX NFP W/KB UK 5CB0L59436 ● Upper Case Q 80SX FP W/KB JA 5CB0L59201 ● Upper Case Q 80SX NFP W/KB JA 5CB0L46647 ● Upper Case Q 80SX FP W/KB IT 5CB0L59525 ●...
Page 83
Lenovo V310-14ISK/Lenovo V310-15ISK Table 5. Parts list—Overall (continued) Lenovo Lenovo No. FRU FRU no. V310-14ISK V310-15ISK Upper Case Q 80SX NFP W/KB SA 5CB0L59172 ● Upper Case Q 80SX FP W/KB SW 5CB0L59357 ● Upper Case Q 80SX NFP W/KB SW 5CB0L59503 ● Upper Case Q 80SX FP W/KB USINT'E 5CB0L59193 ● Upper Case Q 80SX NFP W/KBUSINT'E 5CB0L59349 ● Upper Case Q 80SX FP W/KB CZ-SK 5CB0L59221 ● Upper Case Q 80SX NFP W/KB CZ-SK 5CB0L59247 ● Upper Case Q 80SX FP W/KB BU 5CB0L59389 ●...
Lenovo V310-14ISK/Lenovo V310-15ISK LCD FRUs In Lenovo V310-14ISK/Lenovo V310-15ISK, there are following types of LCDs. • “14.0-in. HD LED” Lenovo V310-14ISK...
Page 99
Lenovo V310-14ISK/Lenovo V310-15ISK Table 6. Parts list—LCD FRUs Lenovo Lenovo No. FRU FRU no. V310-14ISK V310-15ISK LCD Bezel Q 80SX BLK 5B30L46641 ● LCD Bezel Q 80SY BLK 5B30L46622 ● LG LP140WHU-TPH1 HDT AG S NB 5D10K81464 ● AUO B140XTN02.E HW0A HD AG S NB 5D10G95364 ● IN N140BGA-EA3 HDT AG S NB 5D10K85755 ● AU B140HTN01.E 2A FHDT AG S NB 5D10L08701 ● IN N140HGE-EAA C4 FHDT AG S NB 5D10K93439 ● LG LP156WHU-TPH1 HDT AG S NB 5D10K81461 ●...
Lenovo V310-14ISK/Lenovo V310-15ISK Power cords A Lenovo power cord for a specific country or region is usually available only in that country or region: Table 10. Parts list—3-pin power cords Lenovo Lenovo Region CRU ID. V310-14ISK V310-15ISK UK 3pin 145000593 ● ● • LINETEK LP-61L+ H03VV-F+ LS15 1m UK 3pin 145000561 ● ● • Longwell LP-61L+H03VV-F+LS-18 1m UK 3pin 145000605 ● ● • VOLEX MP5004+H03VV-F+VAC5S 1m UK 3pin 145500000 ● ● • lux 0031+H03VV-F 0.75/3C+0011 1m Europe 3pin 145000585 ●...
Page 102
Lenovo V310-14ISK/Lenovo V310-15ISK Hardware Maintenance Manual Table 10. Parts list—3-pin power cords (continued) Lenovo Lenovo Region CRU ID. V310-14ISK V310-15ISK Japan 3pin 145000555 ● ● • Longwell LP-54+VCTF+LS-18 1m Japan 3pin 145000530 ● ● • VOLEX VAC5S+VCTF+M755 1m Japan 3pin 145500005 ● ● • lux 0018(E)+VCTF 0.75/3C+0021 1m Australia 3pin 145000589 ● ● • LINETEK LS15+H03VV-F+LP-23A 1m...
Page 103
Lenovo V310-14ISK/Lenovo V310-15ISK Table 10. Parts list—3-pin power cords (continued) Lenovo Lenovo Region CRU ID. V310-14ISK V310-15ISK Brazil 3pin 145000564 ● ● • Longwell LP-46+H03VV-F+LS-18 1m Brazil 3pin 145000527 ● ● • VOLEX CH10S3+H03VV-F+VAC5S 1m Brazil 3pin 145500011 ● ● • lux 0034+H03VV-F 0.75/3C+0011 1m Israel 3pin 145000595 ● ● • LINETEK LS15+H03VV-F+LP-41 1m Israel 3pin 145000563 ●...
Lenovo V310-14ISK/Lenovo V310-15ISK Hardware Maintenance Manual Notices Lenovo may not offer the products, services, or features discussed in this document in all countries. Consult your local Lenovo representative for information on the products and services currently available in your area. Any reference to a Lenovo product, program, or service is not intended to state or imply that only that Lenovo product, program, or service may be used. Any functionally equivalent product, program, or service that does not infringe any Lenovo intellectual property right may be used instead. However, it is the...
Notices Trademarks The following terms are trademarks or registered trademarks of Lenovo in the United States, other countries, or both. Lenovo OneKey Microsoft and Windows are trademarks of Microsoft Corporation in the United States, other countries, or both. Other company, products, or service names may be trademarks or service marks of others.