Advertisement
Quick Links
Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions
and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS.
USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE
DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAFETY INSTRUCTIONS
Keep crane, and lifting slings, supports and beams in good working order and condition. Follow the inspection requirements as described
!
in Section 5. Take immediate action to repair or replace damaged parts by contacting your supplier. Ensure that all accessory lifting
devices are suitably certified. If crane is damaged immediately remove from service.
Ensure the surface on which the crane is used is level and firm, being capable of sustaining the crane and the maximum load.
!
Never use crane on tarmacadam or on soft surfaces.
%
Ensure that the crane legs and arms are always locked before use, and jib extension is locked in fixed jib position by means of the lock split pin.
!
Keep children and unauthorised persons away from the work area.
!
Keep work area clean and tidy, and free from unrelated materials, and ensure that there is adequate lighting.
!
Ensure that load does not exceed the crane’s maximum lifting capacity. Overloading the crane is dangerous. Where appropriate, use only
!
the lifting points recommended by the manufacturer of the item to be lifted, i.e. vehicle engine.
Before lifting the load ensure that the crane jib is in the lowest possible position, that there are no obstacles which may snag the load
!
whilst it is being lifted and that the area above the jib is clear.
DO NOT apply any sideways pressure to the crane during lifting or suspension of load.
%
To avoid injury, be fully aware of your own and other persons locations in relation to the lifting and lowering of the load.
!
Keep a sound footing and balance, and ensure that the floor is not slippery. Wear non-slip shoes.
!
Ensure the centre of gravity of the load always remains inside the crane base.
!
DO NOT attempt to lift the load at an angle, and do not allow the load to swing during lifting.
%
DO NOT allow the load to drop suddenly. Lower load with care and ensure that you are fully aware of the condition of the surface onto
%
which the load is to be lowered.
DO NOT operate the hydraulic power unit beyond its maximum stroke, as indicated on the label.
%
DO NOT load beyond rated capacity for each specified jib position as indicated in Section 2. The capacity of crane reduces as the jib is extended.
%
DO NOT position any part of your body beneath the load, and do not climb on the crane.
%
DO NOT use the crane to move or transport a load around the workshop. The crane is a lifting device only.
%
DO NOT attempt to adjust the safety valve, as this has been set and sealed by the manufacturer.
%
DO NOT use the crane for a task it has not been designed to do.
%
DO NOT use whilst under the influence of drugs, alcohol or intoxicating medication.
%
When not in use, store the crane in a safe, dry, childproof, area.
!
WARNING: Failure to heed safety and warning instructions may result in damage and/or personal injury and will invalidate the warranty.
F
p
2. SPECIFICATIONS
MODEL
Max. lift @ min. jib extension: mm . . . . . .2020 . . .2020 . . .2020
Max. lift @ max. jib extension: mm . . . . . .2340 . . .2340 . . .2340
Height (max) of frame: mm . . . . . . . . . . . . . . . . . .125 . . . . .125 . . . . .125
Length (max) of frame: mm . . . . . . . . . . . . . . . . .1420 . . . .1420 . . . .1420
Width (max) of frame: mm . . . . . . . . . . . . . .1090 . . .1130 . . .1130
Overall height: mm . . . . . . . . . . . . . . . . . .1520 . . .1520 . . .1520
Width inside frame (max): mm . . . . . . . . . .950 . . . .970 . . . .970
Distance between rear wheel centres: mm . . . . 300 . . . .300 . . . .300
Weight: kg . . . . . . . . . . . . . . . . . . . . . . . . . 73 . . . . .90 . . . . .98
3. ASSEMBLY INSTRUCTIONS
Your crane is delivered assembled but in a folded condition. Before using it is necessary to lay the folded crane on its ‘back’ on the floor
and proceed as follows.
3.1.
Lower the crane legs. Lock them in place with the pins and split pins.
3.2.
Rotate the assembled crane onto its wheels.
3.3.
Open the valve at top of ram by turning to left and pump 10-20 times. This will purge any air that may have entered during transit.
3.4.
Pull crane jib up slightly, close valve and pump the handle. The jib will now raise. Pump the jib all the way up once and lower it again (this
will check the oil level).
3.5.
Crane is now ready. Ensure that it is complete and not damaged. If you experience any problems contact your supplier immediately.
4. OPERATING INSTRUCTIONS
F
WARNING! Ensure that you read, understand and apply Section 1 safety instructions, and that parts 3.3 and 3.4 have been
p
successfully performed before using the crane.
4.1.
Pump the handle to raise the jib to the appropriate height at which the load may be secured.
4.2.
Connect the crane hook to the load using a suitable certified sling or support beam. Ensure that you are aware of the load weight
and check that it is within the capacity of the crane at the jib extension you are using. When removing engines ensure that you know
the engine weight. Use only lifting points recommended by the vehicle manufacturer.
4.3.
Lift only from directly above the load.
500KCA
750VA
WF10
FWARNING! DO NOT LIFT THE LOAD AT AN ANGLE!
INSTRUCTIONS FOR:
PROFESSIONAL FOLDING CRANES
500KCA, 750VA & WF10.
Models:
MODEL
Lifting capacity, Position 1: kg . . . . . .550 . . .750 . .1100
Lifting capacity, Position 2: kg . . . . . .500 . . .700 . .1000
Lifting capacity, Position 3: kg . . . . . .450 . . .650 . . .900
Lifting capacity, Position 4: kg . . . . . .400 . . .600 . . .800
Lifting capacity, Position 5: kg . . . . . .350 . . .550 . . .700
Length of jib, Position 1: mm . . . . . . .955 . . .955 . . .955
Length of jib, Position 2: mm . . . . . .1060 . .1060 . .1060
Length of jib, Position 3: mm . . . . . .1165 . .1165 . .1165
Length of jib, Position 4: mm . . . . . .1270 . .1270 . .1270
Length of jib, Position 5: mm . . . . . .1375 . .1375 . .1375
500KCA 750VA
WF10
500KCA/750VA/WF10 - 3 - 181202
Advertisement
Related Manuals for Sealey 500KCA
Summary of Contents for Sealey 500KCA
- Page 1 500KCA, 750VA & WF10. Models: Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions and properly maintained, give you years of trouble free performance. IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS.
- Page 2 5.2.2. The ram is filled with oil and should only require occasional topping up. For the occasional top up DO NOT use brake fluid, as this will damage the hydraulic seals, proceed as follows: a) Use only good quality hydraulic jack oil available from your Sealey dealer. b) Fully lower the jib extension arm.