Sealey SV20 Series Manual
20v cordless trimming router - body only / router plunge base
Hide thumbs
Also See for SV20 Series:
- Manual (12 pages) ,
- Quick start manual (9 pages) ,
- Instruction manual (8 pages)
Advertisement
Table of Contents
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to
Wear eye
instructions
protection
1. SAFETY
1.1.
GENERAL SAFETY
WARNING! Ensure that Health & Safety, local authority and general workshop practice regulations are adhered to when using this
‰
equipment.
WARNING! Remove the battery from the router before changing bits, servicing or performing any maintenance.
‰
Maintain the router in good condition. Check moving parts alignment on a regular basis.
9
Replace or repair damaged parts. Use an authorised service agent and use recommended parts only. Unauthorised parts may be
9
dangerous and will invalidate the warranty.
Keep the router clean and the bits sharp for best and safest performance.
9
Wear approved safety eye protection (standard spectacles are not adequate) and dust mask.
9
Maintain correct balance and footing. Ensure the floor is not slippery and wear non-slip shoes.
9
Keep children and unauthorised persons away from the working area.
9
Remove ill fitting clothing. Remove ties, watches, rings and other loose jewellery and contain long hair.
9
Use in a suitable work area. Keep area clean, tidy and free from unrelated materials. Ensure there is adequate lighting.
9
Remove any adjusting key or wrench before turning tool on.
9
Evaluate your work area before using the router e.g. work pieces may conceal electric cables or water piping.
9
Secure non-stable workpiece with a clamp, vice or other adequate holding device.
9
Prevent unintentional starting. Ensure the switch is in the OFF position before inserting the battery pack, picking up or carrying the tool.
9
Before making a cut ensure that all accessories and adjustment fixings are fully tightened.
9
Only use router bits that are specifically designed for use with this machine.
9
Maintain and use in accordance with these instructions.
9
When not in use store in a safe, dry, childproof area.
9
DO NOT over reach. Keep proper footing and balance at all times to enable better control of the tool in unexpected situations.
8
DO NOT use the router where there are flammable liquids, solids or gases such as paint solvents, etc.
8
DO NOT allow children to operate the router.
8
DO NOT allow persons unfamiliar with the tool or with these instructions to operate the tool.
8
DO NOT operate the router if any parts are missing as this may cause failure and/or personal injury.
8
DO NOT leave the router operating unattended.
8
DO NOT carry the router with your finger on the power switch.
8
DO NOT use the router for a task it is not designed to perform.
8
DO NOT use a bit which is damaged, cracked or distorted.
8
DO NOT use the tool if the switch does not turn it on and off. The tool must be repaired first.
8
DO NOT operate the router when you are tired, under the influence of alcohol, drugs or intoxicating medication.
8
DO NOT get the router wet or use in damp or wet locations.
8
DO NOT hold unsecured workpiece in your hand whilst cutting.
8
DO NOT force the router to cut but allow it to operate at its normal working speed and feed rate.
8
DO NOT reach under the workpiece whilst the bit is cutting. Keep hands away from the cutting area and do not attempt to remove
8
dust / swarf.
DO NOT fit or use a router bit that is intended to cut metal. Always ensure that the saw is fitted with the correct wood cutting bit.
8
DO NOT substitute an abrasive wheel for the router bit.
8
DO NOT allow the bit to come into contact with nails or other steel fixings used in old timber or existing timber structures. Inspect the
8
workpiece before commencing cutting and remove any potential hazards.
DO NOT start the router with the bit in contact with the workpiece. Allow the bit to run up to speed before proceeding to cut.
8
Take note of and follow specific safety advice in Operation section of the manual.
9
DO NOT force the power tool. Use the correct power tool for your application. The correct power tool will do the job better and safer
8
at the rate for which it was designed.
Remove the battery pack from the power tool before making any adjustments, changing accessories, or storing power tools. Such
9
preventive safety measures reduce the risk of starting the power tool accidentally.
Maintain tools and accessories. Check for misalignment or binding of the moving parts, breakage of parts and any other condition
9
that may affect the tool's operation. If damaged, have the tool repaired by qualified engineers before use.
Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier
9
to control.
© Jack Sealey Limited
20V SV20 SERIES CORDLESS TRIMMING
ROUTER - BODY ONLY / ROUTER PLUNGE
BASE
MODEL NO:
Wear protective
Wear safety
gloves
footwear
Original Language Version
CP20VTR / RPB01
Wear protective
Wear ear
clothing
protection
Wear
dust mask
CP20VTR Issue 1 15/02/2023
Advertisement
Table of Contents
Related Manuals for Sealey SV20 Series
Summary of Contents for Sealey SV20 Series
- Page 1 CP20VTR / RPB01 MODEL NO: Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions, and properly maintained, give you years of trouble free performance. IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED.
-
Page 2: Specification
Insert the router bit all the way into the collet cone. Depress the shaft lock to engage spindle. Tighten the collet nut with the wrench or tighten the collet nut securely with the two wrenches. To remove the bit, follow the installation procedure in reverse. fig.3 Original Language Version © Jack Sealey Limited CP20VTR Issue 1 15/02/2023... - Page 3 Loosen the clamp screw and adjust the distance between the router bit and the router guide by turning the adjusting screw (1 mm (3/64”) per turn). At the desired distance, tighten the clamp screw to secure the router guide. 5.6.3. Move the tool with the guide roller riding the side of the workpiece (fig.6, fig.7). fig.6 fig.7 Original Language Version © Jack Sealey Limited CP20VTR Issue 1 15/02/2023...
-
Page 4: General Safety
DO NOT force the power tool. Use the correct power tool for your application. The correct power tool will do the job better and safer at the rate for which it was designed. Remove the battery pack from the power tool before making any adjustments, changing accessories, or storing power tools. Such Original Language Version © Jack Sealey Limited CP20VTR Issue 1 15/02/2023... - Page 5 Set vernier to 0 and raise spindle so that the Indicator cup matches the scale to the depth of cut required i.e 3 mm graduations and lock in position. Original Language Version © Jack Sealey Limited CP20VTR Issue 1 15/02/2023...
- Page 6 To prolong the useful life of the router always clean it thoroughly after use and protect bits with a rust preventative. DO NOT clean with any solvents as they may attack the material. Clean the router with a dry cloth and remove sawdust from ventilation slots. Original Language Version © Jack Sealey Limited CP20VTR Issue 1 15/02/2023...
-
Page 7: Environment Protection
Important: No Liability is accepted for incorrect use of this product. Warranty: Guarantee is 12 months from purchase date, proof of which is required for any claim. Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR 01284 757500 sales@sealey.co.uk...