Advertisement
Quick Links
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions and maintained properly, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT
CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL
INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Warning: Electricity Indoor use only
Refer to Instruction
Manual
1. SAFETY
1.1.
PLUG & MAINS POWER SUPPLY
WARNING! It is the responsibility of the owner and the operator to read, understand and comply with the following:
You must check all electrical products, before use, to ensure that they are safe. You must inspect power cables, plugs, sockets and
any other connectors for wear or damage. You must ensure that the risk of electric shock is minimised by the installation of appropriate
safety devices. A Residual Current Circuit Breaker (RCCB) should be incorporated in the main distribution board. We also recommend
that a Residual Current Device (RCD) is used. It is particularly important to use an RCD with portable products that are plugged into a
supply which is not protected by an RCCB. If in any doubt consult a qualified electrician. You may obtain a Residual Current Device by
contacting your Sealey dealer.
You must also read and understand the following instructions concerning electrical safety.
1.1.1. The Electricity at Work Act 1989 requires all portable electrical appliances, if used on business premises, to be tested by a qualified
electrician, using a Portable Appliance Tester (PAT), at least once a year.
1.1.2. The Health & Safety at Work Act 1974 makes owners of electrical appliances responsible
for the safe condition of those appliances and the safety of the appliance operators. If in
any doubt about electrical safety, contact a qualified electrician.
1.1.3. Ensure that the insulation on all cables and on the appliance is safe before connecting it to
the power supply. See 1.1.1. and 1.1.2. and use a Portable Appliance Tester.
1.1.4. Ensure that cables are always protected against short circuit and overload.
1.1.5. Regularly inspect power supply cables and plugs for wear or damage and check all
connections to ensure that none is loose.
1.1.6. IMPORTANT: Ensure that the voltage marked on the appliance matches the power supply
to
be used and that the plug is fitted with the correct fuse - see fuse rating on right.
1.1.7. DO NOT pull or carry the appliance by the power cable.
1.1.8. DO NOT pull the plug from the socket by the cable.
1.1.9. DO NOT use worn or damaged cables, plugs or connectors. Immediately have any faulty
item repaired or replaced by a qualified electrician. When an ASTA/BS approved UK 3 pin
13 amp plug is damaged, cut the cable just above the plug and dispose of the plug safely.
Fit a new plug according to the following instructions (UK only - see diagrams on right).
a) Connect the GREEN/YELLOW earth wire to the earth terminal 'E'.
b) Connect the BROWN live wire to the live terminal 'L'.
c) Connect the BLUE neutral wire to the neutral terminal 'N'.
d) After wiring, check that there are no bare wires, that all wires have been correctly connected, that the cable outer
insulation extends beyond the cable restraint and that the restraint is tight.
1.1.10. If an extension reel is used it should be fully unwound before connection. A reel with an RCD fitted is preferred since any appliance plugged
into it will be protected. The cable core section is important and should be at least 1.5mm
the reel is suitable for this product and for others which may be used in the other output sockets, we recommend the use of 2.5mm
section cable.
1.2.
GENERAL SAFETY
WARNING! Disconnect air dryer/blower from mains supply when not in use, before servicing or performing any maintenance.
WARNING! If the air dryer/blower falls into water or other liquid, immediately switch off at, and disconnect from, the mains power supply.
DO NOT touch the unit until the mains power supply has been disconnected.
Always disconnect the air dryer/blower from the power supply when moving it from one location to another and ensure that it is stood on a
level surface.
Before using ensure there are no materials or items that may be blown about by the stream of air. Mandatory minimum distance from the
unit is one metre.
Keep the air dryer/blower clean and maintained in good condition. For electrical components or motor service, contact an authorised
service agent.
Replace or repair damaged parts. Use recommended parts only (unauthorised parts may be dangerous, and will invalidate your warranty).
DO NOT obstruct the air inlet and outlet sections of the air dryer/blower.
DO NOT operate the air dryer/blower where there are harmful, explosive or flammable gases, fumes or hazardous substances.
DO NOT stand the air dryer/blower on the electrical power cable.
DO NOT insert objects through any of the air dryer/blower grilles.
DO NOT modify speed control or attempt to fit any additional external speed control device to the fan.
DO NOT cover the air dryer/blower when in use.
DO NOT allow children to operate the air dryer/blower.
DO NOT use the air dryer/blower outdoors.
© Jack Sealey Limited
Get In Touch
Call: 0845 6880112
Email: info@adremit.co.uk
INSTRUCTIONS FOR:
AIR DRYER/BLOWER
ADB300, ADB3000
MODEL NOs:
Original Language Version
Our Address
Puravent, Adremit Limited, Unit 5a, Commercial Yard,
Settle, North Yorkshire, BD24 9RH
FUSE RATING:
ADB300 - 5 AMP
ADB3000 - 13 AMP
, but to be absolutely sure that the capacity of
2
ADB300, ADB3000 Issue: 3 (L) - 17/02/17
2
Advertisement
Related Manuals for Sealey ADB3000
Summary of Contents for Sealey ADB3000
- Page 1 ADB300, ADB3000 MODEL NOs: Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions and maintained properly, give you years of trouble free performance. IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED.
- Page 2 Ensure that the power lead is not stretched or positioned in such a way as to cause a hazard. 4.3. Turn the blower on by switching to “I”/ON. If a greater air flow is required, turn the switch to the “II” or “III” setting (ADB3000 only). 4.4.