Advertisement
Quick Links
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to
Wear safety
instructions
footwear
1.
SAFETY
The user shall work in accordance with the instruction handbook.
9
WARNING! Ensure that the load is adequately secured to the lifting platform with appropriate straps before raising the load.
‰
WARNING! DO NOT work under the load until appropriately rated adequate means of support have been correctly positioned.
‰
Maintain the lift in good condition (use an authorised service agent).
9
Replace or repair damaged parts. Use genuine parts only. Unauthorised parts may be dangerous and will invalidate the warranty.
9
Use a qualified person to lubricate and maintain the lift. DO NOT use brake fluid to top up hydraulic unit.
9
Locate the lift in a suitable work area, keep area clean and tidy and free from unrelated materials, and ensure that there is adequate
9
lighting. Also ensure that the floor is level and strong enough (preferably concrete) to take the weight of the lift and the lawn mower. DO
NOT operate the lift on tarmacadam, as the surface may be unstable.
Keep clear of load while lifting and lowering.
9
DO NOT move while loaded.
8
DO NOT adjust safety valve.
8
Keep the lift clean for best and safest performance.
9
It is necessary that the operator can watch the lifting device and the load during all movements.
9
The maximum load weight is 340kg. DO NOT exceed this rated capacity.
9
Remove ill fitting clothing. Remove ties, watches, rings and other loose jewellery, and contain long hair. Wear ANSI-approved safety
9
goggles and heavy duty work gloves during use.
Maintain correct balance and footing, DO NOT over reach. Ensure the floor is not slippery and wear non-slip shoes.
9
Before lifting check that there are no overhead obstructions.
9
When platform has been raised to the working height ensure the locking pin is engaged to prevent accidental lowering.
9
Keep children and unauthorised persons away from the work area.
9
The lowering speed will vary according to the weight of the load and the setting of the release valve.
9
To avoid injury, be fully aware of your own and other persons locations in relation to the lifting, and lowering, of the load.
9
DO NOT use the lift for a task it is not designed to perform.
8
DO NOT operate the lift if damaged.
8
DO NOT operate the lift when you are tired or under the influence of alcohol, drugs or intoxicating medication.
8
DO NOT allow untrained persons to operate the lift.
8
DO NOT make any modifications to the lift and DO NOT adjust or tamper with the safety valve.
8
DO NOT sit or stand on the lift or hold onto it when it is being raised or lowered.
8
DO NOT position any part of your body beneath the load.
8
DO NOT attempt to raise the lift using manual strength.
8
DO NOT allow anyone to stand near the interior frame of the lift whilst raising or lowering.
8
DO NOT use the ram alone to maintain a raised load. ALWAYS confirm the locking pins are engaged.
8
DO NOT work under the raised load until it is secured by suitable means.
8
Before lowering the lift ensure that there are no obstructions underneath and that all persons are standing clear.
9
The operator shall be provided with all necessary information about training and about pumping and translating forces.
9
If more than 400N of effort is generated in lifting, the load shall be lowered by an additional person.
9
Before storing in safe area, ensure all parts are clean and free of grease and oil. Store lift in the lowest position.
9
WARNING! The Warnings, Cautions and Instructions referred to in this manual cannot cover all possible conditions and situations
‰
that may occur. It must be understood that common sense and caution are factors which cannot be built into this product, but must be
applied by the operator.
2.
INTRODUCTION
Safely lift most ZTR, Ride/Stand On Mowers, XL Walk Behind Mowers, Garden Tractors, ATV, UTV, Golf Carts and more. A 610mm
lifting height allows plenty of room under the machine for repairs, maintenance and cleaning. The lift has three heights it can be locked
in, whilst the your machine is worked on. Supports front axle widths between 914mm to 1283mm with five locking postions. The forks
have an adjustable wheel circumference base with 5 locking positions. Max. tyre size w-254mm x h-660mm. A kick pedal to the rear of
the lift makes it easy to tilt it on to its heavy duty wheels, for transporting or postioning. Made with a strong steel frame and coated in an
industrial grey finish. Making it designed and built to last.
© Jack Sealey Limited
MOWER/TRACTOR HYDRAULIC LIFT 340KG
CAPACITY
MODEL NO:
No reaching in
Wear eye
protection
Original Language Version
STML340
STML340
Issue 1
07/02/24
Advertisement
Related Manuals for Sealey STML340
Summary of Contents for Sealey STML340
- Page 1 STML340 MODEL NO: Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions, and properly maintained, give you years of trouble free performance. IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED.
- Page 2 2.1. IDENTIFICATION: Model No: STML340 EXPLODED DRAWING Sealey Power Products, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk, IP32 7AR. SPECIFICATION Model No: STML340 (Standard EN1494) Max Lifting Height: 610mm Front Axle Widths: 914 to 1283mm Max Tyre Size:...
- Page 3 B. With assistance, tip the jack to allow the old hydraulic fluid to drain out of the ram housing completely, and dispose of the old hydraulic fluid in accordance with local regulations. STML340 Issue 1 07/02/24 © Jack Sealey Limited Original Language Version...
- Page 4 IMPORTANT: No Liability is accepted for incorrect use of this product. WARRANTY: Guarantee is 12 months from purchase date, proof of which is required for any claim. Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR 01284 757500 sales@sealey.co.uk...