Advertisement
Quick Links
Service Manual for L1 and L2
Nokia 108,
Nokia 108 DS
RM-944, RM-945
Key features
1.8" QQVGA Display
MicroSD memory card support up to 32GB
VGA Camera
Torch light
Version 1.0
Exploded view
Solder components
Service concept
Disassembly steps
More
Service devices
More
More
©2013 Nokia | Nokia Internal Use only | All Rights Reserved.
Check the repair
policy before
performing any
mechanical repair
on Service Level
1&2!
Assembly hints
More
Product controls and interfaces
More
More
More
Advertisement
Related Manuals for Nokia 108
Summary of Contents for Nokia 108
- Page 1 VGA Camera Torch light Version 1.0 Exploded view Disassembly steps Assembly hints More More More Solder components Service devices Product controls and interfaces More More More Service concept More ©2013 Nokia | Nokia Internal Use only | All Rights Reserved.
- Page 2 DC JACK I0013 TYPE LABEL I0010 SCREW TORX+ SIZE 4 M1.4 x 4.5 I0016 B-COVER I0017 Only available Not reuseable Repair/swap as assembly after removal only in level 3 ©2013 Nokia | Nokia Internal Use only | All Rights Reserved.
- Page 3 RM-944, RM-945 Version 1.0 1) For disassembling you need the Nokia Standard toolkit version 2. Note that the device used in this disassembly procedure is the dual SIM variant, RM-944. All the disassembly steps are the same for both single and dual SIM variants.
- Page 4 3) To detach the B-COVER press the CAMERA BEZEL and then pull the B-COVER with fingers. Remove the B-COVER. 4) If there is a BATTTERY remove it also.
- Page 5 5) Unscrew the four Torx+ size 4 screws in the order shown. 6) To rseparate the D-COVER and the A-COVER, first release the shown clips on the right side with the SRT-6.
- Page 6 7) Use the SRT-6 to release the clips on the bottom side. 8) Then release the clips from the left side of the device.
- Page 7 9) Lift the bottom end of the A-COVER and release the clips on the top side. 10) The D-COVER and the A-COVER can now be separated.
- Page 8 11) Protect the DISPLAY with protective film. 12) Protect the other side of the A-COVER window with protective film.
- Page 9 13) Push out the KEYMAT from the A-COVER. 14) To detach the ENGINE BOARD, first release this clip located near the guiding hole with the SS-93.
- Page 10 15) Then release the shown clip with the SS-93. 16) Continue by releasing the clip near the guiding hole from the left side of the device.
- Page 11 17) Then release the shown clip. 18) To separate the ENGINE BOARD including the UI SHIELDING lift the bottom end first and then remove...
- Page 12 19) Lift up the HEADSET JACK with fingers. 20) Lift up the DC JACK with fingers.
- Page 13 21) Use the sharp end of the SS-93 to release the SPEAKER. Use tweezers to remove the SPEAKER. Do not use it again. Discard it. 22) Use the sharp end of the SS-93 to remove the SPEAKER GASKET. Do not use it again. Discard it.
- Page 14 23) Release the clips holding the UI SHIELDING on the ENGINE BOARD. 24) Remove the UI SHIELDING.
- Page 15 25) Use the dental tool to release the EARPIECE. Be careful not to injure yourself with the sharp end of the dental tool. 26) Remove the EARPIECE and the EARPIECE ADHESIVE with tweezers. Do not use them again. Discard them.
- Page 16 27) Open the CAMERA connector with the SS-93. Be careful not to damage the connector or any components nearby. 28) Use the SS-93 to carefully loosen the adhesive holding the CAMERA.
- Page 17 29) Remove the CAMERA with tweezers. 30) Use the SS-93 to release one corner of the DOMESHEET. Peel off the DOMESHEET with fingers. Do not use it again. Discard it.
- Page 18 31) The Nokia 108, Nokia 108 Dual SIM disassembly procedure is complete. -END OF DISASSEMBLY- ©2013 Nokia | Nokia Internal Use only | All Rights Reserved.
- Page 19 Service Manual Level 1 and 2 Assembly hints Nokia 108, 108 Dual SIM RM-944, RM-945 Version 1.0 1) Align the CAMERA with tweezers. Use the shown clips as references. Close the CAMERA connector with the SS-93. Be careful not to damage the connector or any components nearby.
- Page 20 3) While attaching the ENGINE BOARD including the UI SHIELDING make sure you do not press the DISPLAY. 4) Attach the top end of the A-COVER first. Then put down the bottom end and make sure all the clips are secured.
- Page 21 5) Fasten the four Torx+ size 4 screws in the order shown to the torque of 13 Ncm. -END OF ASSEMBLY HINTS- ©2013 Nokia | Nokia Internal Use only | All Rights Reserved.
- Page 22 Service Manual Level 1 and 2 Solder components Nokia 108, 108 Dual SIM RM-944, RM-945 Version 1.0 BOTTOM Torch Charger Keyboard Fuse V6502 F7051 V6406 ©2013 Nokia | Confidential | All Rights Reserved.
- Page 23 For more information, refer to the Service Bulletin (SB-011) on Nokia Online. Supplier or manufacturer contacts for tool re-order can be found in “Recommended service equipment” document on Nokia Online. ©2013 Nokia | Nokia Internal Use only | All Rights Reserved.
- Page 24 7 — Call key 8 — Scroll key 9 — Right selection key 10 — End/Power key 11 — Keypad 12 — Microphone 13 — Camera 14 — Antenna area ©2013 Nokia | Nokia Internal Use only | All Rights Reserved.
- Page 25 Service Manual Level 1 and 2 Service concept Nokia 108, 108 Dual SIM RM-944, RM-945 Version 1.0 Flashing concept Service CA-101 software FLS-5 Product specific flash adapter Transceiver ©2013 Nokia | Nokia Internal Use only | All Rights Reserved.
- Page 26 Service Manual Level 1 and 2 Version history Nokia 108, 108 Dual SIM RM-944, RM-945 Version 1.0 Version Date Description 24.09.2013 First published version...