. 45 rubber rails or solid state drive (SSD) and storage Diagnostics using PC-Doctor for DOS . 45 converter . . 88 Lenovo ThinkVantage Toolbox (Lenovo System 1040 DIMM . . 92 Toolbox) . 48 1050 Hinge caps . . 95 PC-Doctor for Windows .
Page 6
2070 LCD rear cover and wireless antenna cables AC adapters. . 228 Power cords . . 229 Recovery discs . . 230 Locations ... . . 167 Windows XP Tablet DVDs (32 bit) .
General safety Follow these rules to ensure general safety: v Observe good housekeeping in the area of the machines during and after maintenance. v When lifting any heavy object: 1. Make sure that you can stand safely without slipping. 2. Distribute the weight of the object equally between your feet. 3.
Electrical safety Observe the following rules when working on electrical equipment. Important: Use only approved tools and test equipment. Some hand tools have handles covered with a soft material that does not insulate you when working with live electrical currents. Many customers have, near their equipment, rubber floor mats that contain small conductive fibers to decrease electrostatic discharges.
Page 12
v Do not touch live electrical circuits with the reflective surface of a plastic dental mirror. The surface is conductive; such touching can cause personal injury and machine damage. v Do not service the following parts with the power on when they are removed from their normal operating places in a machine: –...
Safety inspection guide The purpose of this inspection guide is to assist you in identifying potentially unsafe conditions. As each machine was designed and built, required safety items were installed to protect users and service technicians from injury. This guide addresses only those items.
Handling devices that are sensitive to electrostatic discharge Any computer part containing transistors or integrated circuits (ICs) should be considered sensitive to electrostatic discharge (ESD.) ESD damage can occur when there is a difference in charge between objects. Protect against ESD damage by equalizing the charge so that the machine, the part, the work mat, and the person handling the part are all at the same charge.
Safety notices (multilingual translations) The safety notices in this section are provided in the following languages: v English v Arabic v Brazilian Portuguese v French v German v Hebrew v Japanese v Korean v Spanish v Traditional Chinese Safety information...
Page 16
DANGER Before the computer is powered on after FRU replacement, make sure all screws, springs, and other small parts are in place and are not left loose inside the computer. Verify this by shaking the computer and listening for rattling sounds. Metallic parts or metal flakes can cause electrical shorts.
Page 17
DANGER To avoid shock, do not remove the plastic cover that protects the lower part of the inverter card. DANGER Though the main batteries have low voltage, a shorted or grounded battery can produce enough current to burn personnel or combustible materials. DANGER Unless hot swap is allowed for the FRU being replaced, do as follows before removing it: power off the computer, unplug all power cords from electrical outlets, remove the...
Page 20
PERIGO Antes de ligar o computador após a substituição da FRU, certifique-se de que todos os parafusos, molas e outras peças pequenas estejam no lugar e não estejam soltos dentro do computador. Verifique isso sacudindo o computador e procurando ouvir sons de peças soltas.
Page 21
PERIGO Para evitar choque elétrico, não remova a capa plástica que protege a parte inferior da placa inversora. PERIGO Embora as principais baterias possuam baixa voltagem, uma bateria em curto-circuito ou aterrada pode produzir corrente o bastante para queimar materiais de pessoal ou inflamáveis.
Page 22
DANGER Avant de remettre l’ordinateur sous tension après remplacement d’une unité en clientèle, vérifiez que tous les ressorts, vis et autres pièces sont bien en place et bien fixées. Pour ce faire, secouez l’unité et assurez-vous qu’aucun bruit suspect ne se produit. Des pièces métalliques ou des copeaux de métal pourraient causer un court-circuit.
Page 23
DANGER Afin d’éviter tout risque de choc électrique, ne retirez pas le cache en plastique protégeant la partie inférieure de la carte d’alimentation. DANGER Bien que le voltage des batteries principales soit peu élevé, le court-circuit ou la mise à la masse d’une batterie peut produire suffisamment de courant pour brûler des matériaux combustibles ou causer des brûlures corporelles graves.
Page 24
VORSICHT Bevor nach einem FRU-Austausch der Computer wieder angeschlossen wird, muß sichergestellt werden, daß keine Schrauben, Federn oder andere Kleinteile fehlen oder im Gehäuse vergessen wurden. Der Computer muß geschüttelt und auf Klappergeräusche geprüft werden. Metallteile oder-splitter können Kurzschlüsse erzeugen. VORSICHT Die Bereitschaftsbatterie, die sich unter dem Diskettenlaufwerk befindet, kann geringe Mengen Nickel und Cadmium enthalten.
Page 25
VORSICHT Die Leuchtstoffröhre im LCD-Bildschirm enthält Quecksilber. Bei der Entsorgung die örtlichen Bestimmungen für Sondermüll beachten. Der LCD-Bildschirm besteht aus Glas und kann zerbrechen, wenn er unsachgemäß behandelt wird oder der Computer auf den Boden fällt. Wenn der Bildschirm beschädigt ist und die darin befindliche Flüssigkeit in Kontakt mit Haut und Augen gerät, sollten die betroffenen Stellen mindestens 15 Minuten mit Wasser abgespült und bei Beschwerden anschließend ein Arzt aufgesucht werden.
Page 32
PELIGRO Antes de encender el sistema despues de sustituir una FRU, compruebe que todos los tornillos, muelles y demás piezas pequeñas se encuentran en su sitio y no se encuentran sueltas dentro del sistema. Compruébelo agitando el sistema y escuchando los posibles ruidos que provocarían.
Page 33
PELIGRO Para evitar descargas, no quite la cubierta de plástico que rodea la parte baja de la tarjeta invertida. PELIGRO Aunque las baterías principales tienen un voltaje bajo, una batería cortocircuitada o con contacto a tierra puede producir la corriente suficiente como para quemar material combustible o provocar quemaduras en el personal.
Laser compliance statement (multilingual translations) The laser compliance statements in this section are provided in the following languages: v English v Arabic v Brazilian Portuguese v French v German v Hebrew v Japanese v Korean v Spanish v Traditional Chinese Some models of ThinkPad Notebook are equipped from the factory with an optical storage device such as a CD-ROM drive or a DVD-ROM drive.
Page 38
Alguns modelos de computador ThinkPad são equipados na fábrica com um dispositivo de armazenamento ótico, como uma unidade de CD-ROM ou de DVD-ROM. Tais dispositivos também são vendidos separadamente como opcionais. Se uma dessas unidades estiver instalada, ela é certificada nos Estados Unidos em conformidade com os requisitos do Department of Health and Human Services 21 Code of Federal Regulations (DHHS 21 CFR), Subcapítulo J, para produtos a laser da Classe 1.
Page 39
Certains modèles d’ordinateur ThinkPad sont équipés d’origine d’une unité de stockage optique telle qu’une unité de CD-ROM ou de DVD-ROM. Ces unités sont également vendues séparément en tant qu’options. Si l’une de ces unités est installée, elle est certifiée conforme, aux Etats-Unis, aux normes indiquées dans le sous-chapitre J du DHHS 21 CFR relatif aux produits à...
Page 40
Einige ThinkPad-Modelle sind werkseitig mit einem CD-ROM- oder DVD-ROM-Laufwerk ausgestattet. CD- und DVD-Laufwerke können auch gesondert als Zusatzeinrichtung erworben werden. Die Laufwerke erfüllen die Anforderungen gemäß IEC 60825-1 (International Electrotechnical Commission) und gemäß CENELEC EN 60825-1 für Laserprodukte der Klasse 1. Bei der Installation von CD-ROM-Laufwerken, DVD-ROM-Laufwerken oder anderen Lasereinheiten Folgendes beachten: VORSICHT:...
Page 44
Algunos modelos de sistemas ThinkPad están equipados de fábrica con un dispositivo de almacenamiento óptico, como una unidad de CD-ROM o de DVD-ROM. Estas unidades también se venden por separado como opciones. Si está instalada alguna de dichas unidades, se certifica que en los Estados Unidos cumple los requisitos del Department of Health and Human Services 21 Code of Federal Regulations (DHHS 21 CFR) Subchapter J para productos láser de Clase 1.
– “FRU identification for CTO, CMV, and GAV products” on page 41 Important: BIOS and device driver fixes are customer-installable. The BIOS and device drivers are posted on the customer support site http://www.lenovo.com/support System Disassembly/Reassembly videos that show the FRU removals or ®...
Use the following strategy to prevent unnecessary expense for replacing and servicing FRUs: v If you are instructed to replace a FRU but the replacement does not correct the problem, reinstall the original FRU before you continue. v Some computers have both a processor board and a system board. If you are instructed to replace either the processor board or the system board, and replacing one of them does not correct the problem, reinstall that board, and then replace the other one.
MT and 3-digit model, where model = “CTO” (Example: 1829-CTO). Custom Model Variant (CMV) This is a unique configuration that has been negotiated between IBM or Lenovo and the customer. A unique 4-digit MT and 3-digit model is provided to the customer to place orders (Example: 1829-W15).
(this is the same record found in PEW). v eSupport can be accessed at the following Web site: http://www.lenovo.com/ support v To view the key commodities, click on PARTS INFORMATION, then PARTS LOOKUP.
“Checkout guide” on page 45 – “Diagnostics using PC-Doctor for DOS” on page 45 – “Lenovo ThinkVantage Toolbox (Lenovo System Toolbox)” on page 48 – “PC-Doctor for Windows” on page 48 – “PC-Doctor for Rescue and Recovery” on page 49 –...
What to do first When you do return a FRU, you must include the following information in the parts exchange form or parts return form that you attach to it: __ 1. Name and phone number of service technician __ 2. Date of service __ 3.
Note: When you initialize the computer configuration, some devices are disabled, such as the serial port. If you test one of these devices, you will need to enable it by using Configuration utility for DOS. The utility is available on the following Web site: http://www.lenovo.com/support General checkout...
Testing the computer Note: The PC-Doctor diagnostic CD does not support any optical drives connected through USB devices or any others. It supports only the internal optical drive of the ThinkPad Notebook. To run the test, do as follows: 1. Turn off the computer. 2.
Page 55
The options on the test menu are as follows: Diagnostics Interactive Tests v Run Normal Test v Keyboard v Run Quick Test v Video v CPU/Coprocessor v Internal Speaker v Systemboard v Mouse v Video Adapter v Diskette v Fixed Disks v System Load v Diskette Drives v Optical Drive Test...
While the Windows operating system is running, press the ThinkVantage button. You can also run this program as either of the following: v Click Start --> All Programs --> Lenovo ThinkVantage Tools --> System Health and Diagnostics. v Click Start --> Control Panel --> System and Security --> Lenovo’s System Health and Diagnostics.
PC-Doctor for Rescue and Recovery ® In some models of ThinkPad Notebook, the Rescue and Recovery workspace enables you to run the PC-Doctor program to test the hardware features of the computer. To run the test, click “Run Diagnostics” on the Rescue and Recovery main screen. General checkout...
FRU tests The following table shows the test for each FRU. Table 1. FRU tests Applicable test System board 1. Diagnostics --> CPU/Coprocessor 2. Diagnostics --> Systemboard ™ 3. If the ThinkPad X200 UltraBase is attached to the ThinkPad computer, detach it. Place the computer on a horizontal surface, and run Diagnostics -->...
Page 59
Table 1. FRU tests (continued) Applicable test TrackPoint or pointing If the TrackPoint does not work, check the configuration as device specified in the BIOS Setup Utility. If the TrackPoint is disabled, select Automatic to enable it. After you use the TrackPoint, the pointer may drift on the screen for a short time.
Power system checkout To verify a symptom, do the following: 1. Turn off the computer. 2. Remove the battery pack. 3. Connect the ac adapter. 4. Check that power is supplied when you turn on the computer. 5. Turn off the computer. 6.
Checking operational charging To check whether the battery charges properly during operation, use a discharged battery pack or a battery pack that has less than 50% of the total power remaining when installed in the computer. Perform operational charging. If the battery status indicator or icon does not turn on, remove the battery pack and let it return to room temperature.
Checking the backup battery Do the following: 1. Power off the computer, and unplug the ac adapter from it. 2. Turn the computer upside down. 3. Remove the battery pack (see “1020 Battery pack” on page 86). 4. Remove the backup battery (see “1090 Backup battery” on page 104). 5.
Service Web site: When the latest maintenance diskette and the system program service diskette become available, they will be posted on http://www.lenovo.com/spm Restoring the factory contents by using Product Recovery discs When the hard disk drive (HDD) or solid state drive (SSD) is replaced because of a failure, no Product Recovery program is on the new drive.
8. When the recovery process is complete, the Welcome to Microsoft Windows screen is displayed. Follow the instructions on the screen to complete the Windows setup. Restoring the factory contents by using Recovery Disc Set When the hard disk drive (HDD) or solid state drive (SSD) is replaced because of a failure, no product recovery program is on the new drive.
5. Read the license. If you agree with the terms and conditions, select I accept these terms and conditions and then click Next. If you do not agree with the terms and conditions, follow the instructions on the screen. 6. Click Yes in the displayed window to begin the operating system recovery process.
If it has, it can be used for access to the hard disk drive. If no master HDP is available, neither Lenovo nor Lenovo authorized service technicians provide any services to reset either the user or the master HDP, or to recover data from the hard disk drive.
Attention: If User only mode is selected and the user HDP has been forgotten and cannot be made available to the service technician, neither Lenovo nor Lenovo authorized service technicians provide any services to reset the user HDPs or to recover data from the hard disk drive.
Power management To reduce power consumption, the computer has three power management modes: screen blank, sleep (standby in Windows XP), and hibernation. Screen blank mode If the time set on the “Turn off monitor” timer in the operating system expires, the LCD backlight turns off.
Also, in either of the following events, the computer automatically returns from sleep (standby) mode and resumes operation: v The ring indicator (RI) is signaled by a serial device or a PC Card device. v The time set on the resume timer elapses. Note: The computer does not accept any input immediately after it enters sleep (standby) mode.
Symptom-to-FRU index This section contains following information: v “Numeric error codes” v “Error messages” on page 66 v “Beep symptoms” on page 67 v “No-beep symptoms” on page 67 v “LCD-related symptoms” on page 68 v “Intermittent problems” on page 69 v “Undetermined problems”...
Page 71
Table 2. Numeric error codes (continued) Symptom or error FRU or action, in sequence 0187 System board. EAIA data access error—The access to EEPROM is failed. 0188 System board. Invalid RFID Serialization Information Area. 0189 System board. Invalid RFID configuration information area—The EEPROM checksum is not correct.
Page 72
Table 2. Numeric error codes (continued) Symptom or error FRU or action, in sequence 0250 1. Charge the backup battery for more System battery error—System battery is than 8 hours by connecting the ac dead. adapter. 2. Replace the backup battery and run BIOS Setup Utility to reset the time and date.
Page 73
Warning: Your internal hard disk drive customer: If in the primary bay the customer (HDD) may not function correctly on this is using a non-IBM or non-Lenovo hard disk system. Ensure that your HDD is supported drive (HDD), or an old generation IBM...
Error messages Table 3. Error messages Symptom or error FRU or action, in sequence Device address conflict. 1. Load “Setup Defaults” in the BIOS Setup Utility. 2. Backup battery. 3. System board. Allocation error for device. 1. Load “Setup Defaults” in the BIOS Setup Utility.
Beep symptoms Table 4. Beep symptoms Symptom or error FRU or action, in sequence One beep and a blank, unreadable, or 1. Reseat the LCD connector. flashing LCD. 2. LCD assembly. 3. External CRT. 4. System board. One long and two short beeps, and a blank 1.
If the LCD you are servicing has two or less visible defective pixels, it should not be considered faulty. However, if the LCD has three or more visible defective pixels, it will be deemed as defective by Lenovo and it should be replaced. Notes: v This policy applies to all ThinkPad Notebooks purchased on 1 January, 2008 or later.
Intermittent problems Intermittent system hang problems can be due to a variety of causes that have nothing to do with a hardware defect, such as cosmic radiation, electrostatic discharge, or software errors. FRU replacement should be considered only when a problem recurs.
Page 80
Table 7. Status indicators Indicator Meaning Wireless LAN Green: The wireless LAN feature is on, and the radio link is status ready for use, or the data is being transmitted. Blinking green: Data is being transmitted (for some models). Wireless PAN Green: Wireless PAN (Bluetooth wireless or Wireless USB) is status operational.
Page 81
Table 7. Status indicators (continued) Indicator Meaning Fingerprint Green: The fingerprint reader is ready to swipe. reader status Blinking green: only for X201 The fingerprint is being authenticated or has been Tablet authenticated. Blinking amber: The fingerprint could not be authenticated. Status indicators...
Page 84
Table 8. Fn key combinations (continued) Key combination Description Fn+F7 Apply a presentation scheme directly, with no need to start Presentation Director. To disable this function and use the Fn+F7 key combination for switching a display output location, start Presentation Director, and change the settings.
Page 85
Table 8. Fn key combinations (continued) Key combination Description Fn+F12 Put the computer into hibernation mode. To return to normal operation, press the power button for less than four seconds. Note: To use Fn+F12 for hibernation, you must have the ThinkPad PM device driver installed on the computer.
Retaining serial numbers This section includes the following descriptions: v “Restoring the serial number of the system unit” v “Retaining the UUID” v “Reading or writing the ECA information” on page 81 Restoring the serial number of the system unit When the computer was manufactured, the EEPROM on the system board was loaded with the serial numbers of the system and all major components.
The algorithm that generates the number is designed to provide unique IDs until the year A.D. 3400. No two computers in the world have the same number. When you replace the system board, you must set the UUID on the new system board as follows: 1.
Before servicing ThinkPad X200 Tablet and X201 Tablet Removing the SIM card: Some models of the ThinkPad X200 Tablet and X201 Tablet you are servicing might have the SIM card that the customer has been installed. If the computer you are servicing has the SIM card, remove it before you start the servicing.
The only exception to this is if the battery pack is physically damaged or a customer is reporting a possible safety issue. If ThinkVantage Toolbox or Lenovo System Toolbox is not installed in the computer, the customer should download this program before a non-physically damaged battery pack is replaced.
Page 95
Table 10. Removal steps of battery pack Unlock the battery release lever. Holding the battery release lever in the unlocked position 1 , remove the battery pack in the direction shown by arrow When installing: Install the battery pack along the slide rails of the slot. Then make sure that the battery release lever is in the locked position.
1030 Hard disk drive (HDD) cover, HDD, and HDD rubber rails or solid state drive (SSD) and storage converter For access, remove this FRU: v “1020 Battery pack” on page 86 Attention: v Do not drop the hard disk drive or apply any physical shock to it. The hard disk drive is sensitive to physical shock.
Page 97
Table 11. Removal steps of HDD cover, HDD, and HDD drive rubber rails or SSD and storage converter (continued) When installing: Make sure that the HDD connector or SSD connector is attached firmly. Removing and replacing a FRU...
Page 98
Table 11. Removal steps of HDD cover, HDD, and HDD drive rubber rails or SSD and storage converter (continued) HDD and HDD rubber rails: When installing: The rubber rails on the hard disk drive must be attached to the replacement drive. Otherwise the drive cannot be installed properly. SSD and storage converter: ThinkPad X200 Tablet and X201 Tablet Hardware Maintenance Manual...
Page 99
Table 11. Removal steps of HDD cover, HDD, and HDD drive rubber rails or SSD and storage converter (continued) When installing: When you install the SSD in the storage converter, do as follows. Removing and replacing a FRU...
1040 DIMM For access, remove this FRU in order: v “1020 Battery pack” on page 86 Table 12. Removal steps of dimm Remove the DIMM slot cover as shown in this figure. Note: Loosen the screws 1 , but do not remove them. ThinkPad X200 Tablet and X201 Tablet Hardware Maintenance Manual...
Page 101
Table 12. Removal steps of dimm (continued) For ThinkPad X200 Tablet: Note: If only one DIMM is used on the computer you are servicing, the card must be installed in SLOT-0 ( a ), but not in SLOT-1 ( b ). Removing and replacing a FRU...
Page 102
Table 12. Removal steps of dimm (continued) For ThinkPad X201 Tablet: When installing: Insert the notched end of the DIMM into the socket. Press the DIMM firmly, and pivot it until it snaps into the place. Make sure that it is firmly fixed in the slot and does not move easily.
1050 Hinge caps For access, remove this FRU in order: v “1020 Battery pack” on page 86 Table 13. Removal steps of hinge caps Open the LCD unit, and then remove the hinge cap (front). Removing and replacing a FRU...
Page 104
Table 13. Removal steps of hinge caps (continued) Close the LCD unit, and then remove the hinge cap (rear). ThinkPad X200 Tablet and X201 Tablet Hardware Maintenance Manual...
1060 Keyboard For access, remove this FRU in order: v “1020 Battery pack” on page 86 Table 14. Removal steps of keyboard Step Icon Screw (quantity) Color Torque M2 × 6 mm, wafer-head, Black 0.181 Nm nylon-coated (4) (1.85 kgfcm) Removing and replacing a FRU...
Page 106
Table 14. Removal steps of keyboard (continued) Lift the keyboard a little in the direction shown by arrow 4 , and then detach the connector 5 . ThinkPad X200 Tablet and X201 Tablet Hardware Maintenance Manual...
Page 107
Table 14. Removal steps of keyboard (continued) When installing: 1. Attach the keyboard connector firmly. 2. Make sure that the keyboard edges are under the frame as shown in this figure. Then press the keys to latch the keyboard firmly in place. 3.
1070 Extension cable card For access, remove these FRUs in order: v “1020 Battery pack” on page 86 v “1060 Keyboard” on page 97 Table 15. Removal steps of Extension cable card Step Screw (quantity) Color Torque M2 × 3 mm, flat-head, nylon-coated (5) Black 0.181 Nm (1.85 kgfcm)
1080 Palm rest For access, remove this FRU in order: v “1020 Battery pack” on page 86 v “1060 Keyboard” on page 97 Table 16. Removal steps of palm rest Step Icon Screw (quantity) Color Torque M2 × 6 mm, wafer-head, Black 0.181 Nm nylon-coated (5)
Page 110
Table 16. Removal steps of palm rest (continued) ThinkPad X200 Tablet and X201 Tablet Hardware Maintenance Manual...
Page 111
Table 16. Removal steps of palm rest (continued) When installing: When you attach the palm rest, do as follows: 1. Attach the touch pad connector firmly to the system board. 2. Press the left and right top edges of the palm rest to fit it into place. 3.
1090 Backup battery DANGER Use only the battery specified in the parts list for your computer. Any other battery could ignite or explode. For access, remove these FRUs in order: v “1020 Battery pack” on page 86 v “1060 Keyboard” on page 97 v “1080 Palm rest”...
Page 113
Table 17. Removal steps of backup battery (continued) When installing: Make sure that the battery connector is attached firmly. Removing and replacing a FRU...
1100 PCI Express Mini Card for wireless LAN/WiMAX For access, remove these FRUs in order: v “1020 Battery pack” on page 86 v “1060 Keyboard” on page 97 v “1080 Palm rest” on page 101 Table 18. Removal steps of PCI Express Mini Card for wireless LAN/WiMAX Full size PCI Express Mini Card: In step 1 , unplug the jacks by using the removal tool antenna RF connector (P/N: 08K7159) or pick the connectors with your fingers and gently unplug...
Page 115
Table 18. Removal steps of PCI Express Mini Card for wireless LAN/WiMAX (continued) When installing: v In models with wireless LAN card that has two antenna connectors, plug the gray cable into the jack labeled MAIN or M on the card, and the black cable into the jack labeled AUX or A.
Page 116
Table 18. Removal steps of PCI Express Mini Card for wireless LAN/WiMAX (continued) Harf size PCI Express Mini Card: In step 1 , unplug the jacks by using the removal tool antenna RF connector (P/N: 08K7159) or pick the connectors with your fingers and gently unplug them in direction of the arrow.
Page 117
Table 18. Removal steps of PCI Express Mini Card for wireless LAN/WiMAX (continued) When installing: Plug the gray cable into the jack labeled MAIN on the card, and the black cable into the jack labeled AUX. Removing and replacing a FRU...
1110 PCI Express Mini Card for wireless WAN For access, remove these FRUs in order: v “1020 Battery pack” on page 86 v “1060 Keyboard” on page 97 v “1080 Palm rest” on page 101 Table 19. Removal steps of PCI Express Mini Card for wireless WAN In step 1 , unplug the jacks by using the removal tool antenna RF connector (P/N: 08K7159) or pick the connectors with your fingers and gently unplug them in direction of the arrow.
Page 119
Table 19. Removal steps of PCI Express Mini Card for wireless WAN (continued) When installing: When you install the card, plug the red cable into the jack labeled MAIN on the card, and the blue cable into the jack labeled AUX. If the computer you are servicing is the wireless WAN-ready model, put the antenna cables in the cable protection tube and place them as shown in this figure.
1120 Intel Turbo Memory Minicard or Wireless USB PCI Express Half-Mini Card For access, remove these FRUs in order: v “1020 Battery pack” on page 86 v “1060 Keyboard” on page 97 v “1080 Palm rest” on page 101 Table 20. Removal steps of Intel Turbo Memory Minicard or Wireless USB PCI Express Half-Mini Card Note: Step 1 is only for models with the Wireless USB PCI Express Half-Mini ®...
Page 121
Table 20. Removal steps of Intel Turbo Memory Minicard or Wireless USB PCI Express Half-Mini Card (continued) When installing: In models with the Wireless USB PCI Express Half-Mini Card, plug the yellow cable into the jack on the card. Removing and replacing a FRU...
1130 Bluetooth daughter card (BDC-2.1) For access, remove these FRUs in order: v “1020 Battery pack” on page 86 v “1060 Keyboard” on page 97 v “1080 Palm rest” on page 101 Table 21. Removal steps of Bluetooth daughter card Step Screw (quantity) Color...
Page 123
Table 21. Removal steps of Bluetooth daughter card (continued) Turn the Bluetooth daughter card over, and then disconnect the cable from the connector. When installing: Make sure that the connector 4 is attached firmly. Removing and replacing a FRU...
1140 Keyboard bezel For access, remove these FRUs in order: v “1010 Digitizer pen” on page 85 v “1020 Battery pack” on page 86 v “1060 Keyboard” on page 97 v “1080 Palm rest” on page 101 Table 22. Removal steps of keyboard bezel Step Screw (quantity) Color...
Page 125
Table 22. Removal steps of keyboard bezel (continued) Step Screw (quantity) Color Torque M2 × 2 mm, wafer-head, nylon-coated (1) Black 0.181 Nm (1.85 kgfcm) Rotate the LCD unit as shown in this figure. Removing and replacing a FRU...
Page 126
Table 22. Removal steps of keyboard bezel (continued) In step 5 , detach the claws. Then remove the keyboard bezel in the direction shown by arrow 6 . Attention: When you service the keyboard bezel, avoid any kind of rough handling.
1150 I/O card assembly For access, remove these FRUs in order: v “1010 Digitizer pen” on page 85 v “1020 Battery pack” on page 86 v “1060 Keyboard” on page 97 v “1080 Palm rest” on page 101 v “1110 PCI Express Mini Card for wireless WAN” on page 110 v “1140 Keyboard bezel”...
Page 128
Table 23. Removal steps of I/O card assembly (continued) Note: The cable is secured with a double-faced adhesive tape. Turn the I/O card over, and then disconnect the cable from the flip-lock ZIF connector. ThinkPad X200 Tablet and X201 Tablet Hardware Maintenance Manual...
1160 USB sub card For access, remove these FRUs in order: v “1010 Digitizer pen” on page 85 v “1020 Battery pack” on page 86 v “1060 Keyboard” on page 97 v “1080 Palm rest” on page 101 v “1140 Keyboard bezel” on page 116 Table 24.
Page 130
Table 24. Removal steps of USB sub card (continued) Turn the USB sub card over, an then disconnect the cable from the connector. When installing: Route the cable as shown in this figure. ThinkPad X200 Tablet and X201 Tablet Hardware Maintenance Manual...
1170 LCD assembly For access, remove these FRUs in order: v “1010 Digitizer pen” on page 85 v “1020 Battery pack” on page 86 v “1050 Hinge caps” on page 95 v “1060 Keyboard” on page 97 v “1070 Extension cable card” on page 100 v “1080 Palm rest”...
Page 132
Table 25. Removal steps of LCD assembly (continued) Step Screw (quantity) Color Torque M2.5 × 6 mm, wafer-head, nylon-coated (2) Black 0.392 Nm (4 kgfcm) ThinkPad X200 Tablet and X201 Tablet Hardware Maintenance Manual...
Page 133
Table 25. Removal steps of LCD assembly (continued) Before step 3 , strip off the tapes securing the antenna cables, and release the cables from the cable guides of the frame. Removing and replacing a FRU...
Page 134
Table 25. Removal steps of LCD assembly (continued) When installing: Route the antenna cables along the cable guides and secure them with the tapes. As you route the cables, make sure that they are not subjected to any tension. Tension could cause the cables to be damaged by the cable guides, or a wire to be broken.
1180 DC-in connector, fan, digitizer pen case, and pen switch assembly For access, remove these FRUs in order: v “1010 Digitizer pen” on page 85 v “1020 Battery pack” on page 86 v “1050 Hinge caps” on page 95 v “1060 Keyboard” on page 97 v “1070 Extension cable card”...
Page 136
Table 26. Removal steps of DC-in connector, fan, digitizer pen case, and pen switch assembly (continued) Step Screw (quantity) Color Torque M2 × 3.5 mm, wafer-head, nylon-coated (1) Black 0.181 Nm (1.85 kgfcm) ThinkPad X200 Tablet and X201 Tablet Hardware Maintenance Manual...
Page 137
Table 26. Removal steps of DC-in connector, fan, digitizer pen case, and pen switch assembly (continued) In step 6 and 7 , remove the digitizer pen case assembly. Step Screw (quantity) Color Torque M1.6 x 3 + 4.2A mm, shoulder socket-head, Black 0.181 Nm nylon-coated (1)
Page 138
Table 26. Removal steps of DC-in connector, fan, digitizer pen case, and pen switch assembly (continued) Step Screw (quantity) Color Torque M2 × 3.5 mm, wafer-head, nylon-coated (6) Silver 0.181 Nm (1.85 kgfcm) When installing: Attach the wireless radio switch as shown in the figure a . ThinkPad X200 Tablet and X201 Tablet Hardware Maintenance Manual...
Page 139
Table 26. Removal steps of DC-in connector, fan, digitizer pen case, and pen switch assembly (continued) Turn the system board over, and then disconnect the DC-in connector, the fan connector, and the pen switch connector from the system board. When installing: Make sure that the DC-in connector, the fan connector, and the Pen switch connector are attached to the system board firmly.
Page 140
Table 26. Removal steps of DC-in connector, fan, digitizer pen case, and pen switch assembly (continued) When installing: v Before you attach the fan assembly to the computer, apply thermal grease, at an amount of 0.2 grams, on the part marked a as in the following figure. Either too much or too less application of grease can cause a thermal problem due to imperfect contact with a component.
1190 System board and ExpressCard slot assemblys Important notices for handling the system board: When handling the system board, bear the following in mind. v The system board has an accelerometer, which can be broken by applying several thousands of G-forces. Note: Dropping a system board from a height of as little as 6 inches so that it falls flat on a hard bench can subject the accelerometer to as much as 6,000 G’s of shock.
Page 142
Table 27. Removal steps of system board and ExpressCard slot assembly Following components soldered on the system board are extremely sensitive. When you service the system board, avoid any kind of rough handling. For ThinkPad X200 Tablet: ICH (I/O Controller Hub) MCH (Memory Controller Hub) ™...
Page 143
Table 27. Removal steps of system board and ExpressCard slot assembly (continued) For ThinkPad X201 Tablet: PCH (Platform Controller Hub) Accelerometer chip for the HDD Active Protection System Bottom Removing and replacing a FRU...
Page 144
Table 27. Removal steps of system board and ExpressCard slot assembly (continued) Note: The ExpressCard slot assembly is attached to the system board. For ThinkPad X200 Tablet: For ThinkPad X201 Tablet: Step Screw (quantity) Color Torque M2 × 3.5 mm, wafer-head, nylon-coated (1) Silver 0.181 Nm (1.85 kgfcm) ThinkPad X200 Tablet and X201 Tablet Hardware Maintenance Manual...
Page 145
Table 27. Removal steps of system board and ExpressCard slot assembly (continued) Turn the system board over, and then remove the ExpressCard slot assembly from the system board. Removing and replacing a FRU...
1200 Base cover and speaker assembly For access, remove these FRUs in order: v “1010 Digitizer pen” on page 85 v “1020 Battery pack” on page 86 v “1050 Hinge caps” on page 95 v “1060 Keyboard” on page 97 v “1070 Extension cable card”...
Page 147
Table 28. Removal steps of base cover and speaker assembly (continued) When installing: Route the speaker cables along the cable guides as shown in this figure. Removing and replacing a FRU...
Page 148
Applying labels to the base cover: The new base cover FRU is shipped with a kit containing labels of several kinds. When you replace the base cover, you need to apply the following labels: Homologation label Product label Non-mercury label Note: If the computer you are servicing is an LED-backlight LCD model, you need to paste this label so that the notice for mercury on the product label is covered.
Page 149
For some models, you need to apply one or two FCC labels, 7a and 10 . Check the old base cover; if it has one or two FCC labels, find duplicates of them in the label kit and apply them to the new base cover. For the location of each label, refer the following figure: Removing and replacing a FRU...
2010 LCD front bezel For access, remove this FRU: v For access, remove this FRU: – “1020 Battery pack” on page 86 Table 29. Removal steps of LCD front bezel for protection plate LCD model Protection plate LCD model: Step Screw cap Screw (quantity) Color Torque...
Page 151
Table 29. Removal steps of LCD front bezel for protection plate LCD model (continued) When installing: Attach the fingerprint reader connector firmly. Removing and replacing a FRU...
Page 152
Table 30. Removal steps of LCD front bezel for touch panel LCD model or direct-bonding glass LCD model Touch panel LCD model or direct-bonding glass LCD model: Step Screw cap Screw (quantity) Color Torque M2.5 × 8 mm, wafer-head, Black 0.392 Nm nylon-coated (9) (4 kgfcm)
Page 153
Table 30. Removal steps of LCD front bezel for touch panel LCD model or direct-bonding glass LCD model (continued) When installing: Make sure that attach the fingerprint reader connector firmly. Removing and replacing a FRU...
2020 Micro-Processor card For access, remove these FRUs in order: v “1020 Battery pack” on page 86 v “2010 LCD front bezel” on page 142 Table 31. Removal steps of Micro-Processor card Note: Step 1 is only for models with the inverter card. For models without the inverter card, skip step 1 .
Page 155
Table 31. Removal steps of Micro-Processor card (continued) Protection plate LCD model Step Screw (quantity) Color Torque M2 × 3.5 mm, wafer-head, nylon-coated (3) Silver 0.181 Nm (1.85 kgfcm) M2 × 3 mm, height 4.2 mm, stud, Black 0.181 Nm nylon-coated (1) (1.85 kgfcm) Touch panel LCD model or direct-bonding glass LCD model...
Page 156
Table 31. Removal steps of Micro-Processor card (continued) When installing: Make sure that the connector 5 is attached firmly. ThinkPad X200 Tablet and X201 Tablet Hardware Maintenance Manual...
2030 Inverter card For access, remove these FRUs in order: v “1020 Battery pack” on page 86 v “2010 LCD front bezel” on page 142 v “2020 Micro-Processor card” on page 146 Table 32. Removal steps of inverter card Note: Some models do no have the inverter card. Step Screw (quantity) Color...
2040 Hinges For access, remove these FRUs in order: v “1010 Digitizer pen” on page 85 v “1020 Battery pack” on page 86 v “1050 Hinge caps” on page 95 v “1060 Keyboard” on page 97 v “1070 Extension cable card” on page 100 v “1080 Palm rest”...
Page 159
Table 33. Removal steps of hinge (continued) Detach the hinge from the LCD rear cover, and gently pull the cables out through the guide hole in the hinge. Pull them all at once. As you pull them, be sure not to subject them to any tension, which could cause them to be damaged by the cable guides, or could break a wire.
2050 LCD panel, LCD bracket L and R, and LCD cable For access, remove these FRUs in order: v “1010 Digitizer pen” on page 85 v “1020 Battery pack” on page 86 v “1050 Hinge caps” on page 95 v “1060 Keyboard” on page 97 v “1070 Extension cable card”...
Page 161
Table 34. Removal steps of LCD panel and LCD cable for protection plate LCD model Protection plate LCD model: Step Screw cap Screw (quantity) Color Torque M2.5 × 8 mm, wafer-head, Black 0.392 Nm nylon-coated (4) (4 kgfcm) M2 × 3 mm, flat-head, Black 0.181 Nm nylon-coated (6)
Page 162
Table 34. Removal steps of LCD panel and LCD cable for protection plate LCD model (continued) In step 4 , detach the claws. Then remove the LCD panel. When installing: Make sure that all the claws are attached firmly. ThinkPad X200 Tablet and X201 Tablet Hardware Maintenance Manual...
Page 163
Table 34. Removal steps of LCD panel and LCD cable for protection plate LCD model (continued) Note: Step 5 is only for models with the integrated camera. For models without the integrated camera, skip step 5 . When installing: Make sure that the connector 5 is attached firmly. Removing and replacing a FRU...
Page 164
Table 34. Removal steps of LCD panel and LCD cable for protection plate LCD model (continued) Turn the LCD panel over, and then remove the LCD cable from the LCD panel. When installing: Make sure that the LCD cable connector are attached firmly. ThinkPad X200 Tablet and X201 Tablet Hardware Maintenance Manual...
Page 165
Table 35. Removal steps of LCD panel, LCD bracket L and R, and LCD cable for touch panel LCD model or direct-bonding glass LCD model Touch panel LCD model or direct-bonding glass LCD model: Step Screw (quantity) Color Torque M2 × 3.5 mm, wafer-head, nylon-coated (5) Silver 0.181 Nm (1.85 kgfcm) Removing and replacing a FRU...
Page 166
Table 35. Removal steps of LCD panel, LCD bracket L and R, and LCD cable for touch panel LCD model or direct-bonding glass LCD model (continued) Note: Step 2 is only for models with the integrated camera. For models without the integrated camera, skip step 2 . When installing: Make sure that the connector 2 is attached firmly.
Page 167
Table 35. Removal steps of LCD panel, LCD bracket L and R, and LCD cable for touch panel LCD model or direct-bonding glass LCD model (continued) Remove the LCD bracket L and R a . Step Screw (quantity) Color Torque M2 ×...
Page 168
Table 35. Removal steps of LCD panel, LCD bracket L and R, and LCD cable for touch panel LCD model or direct-bonding glass LCD model (continued) Turn the LCD panel over, and then remove the LCD cable b from the LCD panel.
Page 169
Table 35. Removal steps of LCD panel, LCD bracket L and R, and LCD cable for touch panel LCD model or direct-bonding glass LCD model (continued) Multitouch panel LCD model: When installing: Make sure that the LCD cable connector are attached firmly. Removing and replacing a FRU...
2060 Integrated camera For access, remove these FRUs in order: v “1010 Digitizer pen” on page 85 v “1020 Battery pack” on page 86 v “1050 Hinge caps” on page 95 v “1060 Keyboard” on page 97 v “1070 Extension cable card” on page 100 v “1080 Palm rest”...
2070 LCD rear cover and wireless antenna cables For access, remove these FRUs in order: v “1010 Digitizer pen” on page 85 v “1020 Battery pack” on page 86 v “1050 Hinge caps” on page 95 v “1060 Keyboard” on page 97 v “1070 Extension cable card”...
Page 172
Table 37. Removal steps of LCD rear cover and wireless antenna cables (continued) In step 4 , release the antenna cables from the cable guides of the rear cover. ThinkPad X200 Tablet and X201 Tablet Hardware Maintenance Manual...
Page 173
Table 37. Removal steps of LCD rear cover and wireless antenna cables (continued) Remove the center latch from the LCD rear cover. Step Screw (quantity) Color Torque M2 × 3.5 mm, wafer-head, nylon-coated (2) Silver 0.181 Nm (1.85 kgfcm) Removing and replacing a FRU...
Page 174
Table 37. Removal steps of LCD rear cover and wireless antenna cables (continued) When installing: Place the antenna assembly as shown in this figure. Wireless WAN antenna, AUX (blue) Wireless LAN antenna, AUX (black) Wireless USB antenna (yellow) Wireless WAN antenna, MAIN (red) Wireless LAN antenna, MAIN (gray) MIMO antenna (white) Attention: As you route the antenna cables, make sure that they are not...
Rear view Status indicators Note: For the description of each indicator, see “Status indicators” on page ExpressCard slot Wireless radio switch Universal Serial Bus (USB) connector RJ-45 (Ethernet) connector External monitor connector AC power connector Security key hole Rear view (tablet mode) Tablet buttons Fingerprint reader Status indicators...
Rear view (ThinkPad X200 UltraBase) AC power connector Universal serial bus (USB) connectors External monitor connector DisplayPort connector Headphone jack Microphone jack RJ-45 (Ethernet) connector Security keyhole Security lock key Universal serial bus (USB) connector Serial Ultrabay Slim device release latch Serial Ultrabay Slim device eject lever Serial Ultrabay Slim device Docking connector...
Overall ThinkPad X200 Tablet and X201 Tablet Hardware Maintenance Manual...
Page 183
Table 38. Parts list—Overall FRU no. See “Miscellaneous parts” on page 225. LCD unit (see “LCD FRUs for touch panel LCD or direct-bonding glass LCD” on page 207 or “LCD FRUs for protection plate LCD” on page 216.) Extension cable card assembly for X200 Tablet 42W8085 Extension cable card assembly for X201 Tablet 75Y4059...
Page 184
Table 38. Parts list—Overall (continued) FRU no. Wireless USB PCI Express Half-Mini Card v 4184-CTO, H4x, H6x v 7448-CTO, H3x, H5x v 7449-CTO v 7450-CTO v 7453-CTO v 2263-CTO v 2266-CTO 43Y6501 Japan 43Y6503 ® ™ System board with Intel Core 2 Duo mobile processor SU9300 with TPM (1.2 GHz) 60Y3881...
Page 185
Table 38. Parts list—Overall (continued) FRU no. System board with Intel Core 2 Duo mobile processor SU9600 without TPM (1.6 GHz) 60Y3899 v 4184-CTO v 7448-CTO v 7449-CTO v 7450-CTO v 7453-CTO v 2263-CTO v 2266-CTO System board with Intel Core 2 Duo mobile processor SL9300 with TPM (1.6 GHz) 60Y3880 v 4184-CTO, 8Ex, 97x, E4x, E6x, E7x, E9x, F4x, F5x, F7x, F8x, GMx, H6x v 7448-CTO, 8Dx, 8Vx, 8Wx, 8Xx, 9Dx, E3x, E5x, E8x, EAx, F3x, F5x, F6x, F8x, GMx, H5x...
Page 186
Table 38. Parts list—Overall (continued) FRU no. System board with Intel Core 2 Duo mobile processor SL9600 with TPM (2.13 GHz) 60Y3894 v 4184-CTO, 54x v 7448-CTO, 3Cx, 3Hx, 3Kx, 3Lx, 3Mx, 3Nx v 7449-CTO, 43x, 44x, 45x, 47x, 4Ax, 4Bx, 4Cx, 4Dx, 4Fx, 4Hx, 4Jx, 4Kx, 4Px, 4Qx, 4Vx, CCx, GLx, GSx, GTx v 7450-CTO, 2Lx, 2Mx, 2Nx, 65x, 66x, 67x, 68x, 69x, 6Ax, 6Bx, 6Cx, 6Jx, 6Px, 6Ux, 6Vx, 6Wx, 6Xx, 9Nx, 9Px, 9Rx, 9Sx, 9Tx, D3x, D4x, D5x, D6x, DBx, DCx, DDx, DEx, GHx,...
Page 188
Table 38. Parts list—Overall (continued) FRU no. System board with Intel Core i7-640LM LV without TPM 63Y2087 v 0053-CTO v 0831-CTO v 2985-CTO v 3093-CTO v 3113-CTO v 3144-CTO v 3239-CTO 512-MB DDR3-1066 SDRAM SO-DIMM (PC3-8500) card 43R1775 v 4184-CTO v 7448-CTO, 2Ex, 8Vx v 7449-CTO v 7450-CTO, 8Cx...
Page 190
Table 38. Parts list—Overall (continued) FRU no. 4-GB DDR3-1333 SDRAM SO-DIMM (PC3-10600) card Low Halogen 55Y3717 v 0053-CTO v 0831-CTO v 2985-CTO v 3093-CTO v 3113-CTO v 3144-CTO v 3239-CTO ® Qualcomm UNDP1 - Wireless WAN card 42T0961 v 4184-CTO v 7448-CTO v 7449-CTO v 7450-CTO, 6Cx...
Page 192
Table 38. Parts list—Overall (continued) FRU no. ThinkPad 11b/g/n Wireless LAN Mini-PCI Express Adapter II 60Y3177 v 4184-CTO, 53x, 54x v 7448-CTO, 38x, 3Ax, 3Ex v 7449-CTO, 4Xx, 4Yx v 7450-CTO, 63x, 6Bx, 6Fx, 6Gx v 7453-CTO, 6Bx v 2263-CTO v 2266-CTO v 0053-CTO v 0831-CTO...
Page 194
Table 38. Parts list—Overall (continued) FRU no. I/O card assembly without modem connector, with 3-in-1 Media Card Reader for X201 60Y5408 Tablet v 0053-CTO v 0831-CTO v 2985-CTO, C8x, C9x v 3093-CTO, 29x, 2Cx v 3113-CTO v 3144-CTO v 3239-CTO Battery pack, 4 cell, 12 42T4657 v 4184-CTO, 25x, 2Vx, 53x, 54x, 8Ex, 97x, F4x, F5x, F7x, F8x, FBx, FCx, GMx, GNx...
Page 196
Table 38. Parts list—Overall (continued) FRU no. SATA hard disk drive, 80 GB, 5,400 rpm 42T1491 v 4184-CTO v 7448-CTO v 7449-CTO v 7450-CTO v 7453-CTO v 2263-CTO v 2266-CTO SATA hard disk drive, 80 GB, 5,400 rpm 42T1305 v 4184-CTO v 7448-CTO v 7449-CTO v 7450-CTO...
Page 197
Table 38. Parts list—Overall (continued) FRU no. SATA hard disk drive, 160 GB, 5,400 rpm 45N7215 v 4184-CTO, 25x, E4x, E6x, E7x, F4x, F5x, FBx, FCx, H6x v 7448-CTO, 2Ex, 2Qx, 3Ex, 8Vx, 9Kx, 9Lx, E3x, E5x, E8x, F3x, F5x, FAx, FCx, H5x v 7449-CTO, 25x, 2Qx, 2Tx, 43x, 44x, 9Ax, 9Ex, 9Fx, E5x, E8x, EWx, EYx, F9x, GPx, GSx v 7450-CTO, 25x, 2Ax, 2Cx, 2Dx, 2Gx, 2Nx, 2Px, 66x, 8Yx, 93x, E6x, E7x, EXx, EYx v 7453-CTO, 25x, 2Cx, 2Dx, E6x, E7x...
Page 198
Table 38. Parts list—Overall (continued) FRU no. SATA hard disk drive, 250 GB, 5,400 rpm OP 42T1481 v 4184-CTO, 2Vx, 53x, 8Ex, 97x, EFx, EGx, ENx, F7x, F8x, FFx, FGx, GMx, GNx, H4x v 7448-CTO, 38x, 3Ax, 3Bx, 3Gx, 8Dx, 8Wx, 8Xx, 9Dx, EEx, EHx, EPx, F6x, F8x, FEx, FGx, FKx, G6x, GMx, GNx, H3x v 7449-CTO, 4Bx, 4Px, 4Rx, 4Zx, 8Qx, 8Rx, 8Sx, 9Hx, C3x, C4x, C5x, EHx, EPx, FLx, FNx, FWx, FXx, G5x, G6x...
Page 201
Table 38. Parts list—Overall (continued) FRU no. SATA hard disk drive, 320 GB, 5,400 rpm 45N7231 v 0053-CTO, 75x, 76x v 0831-CTO, A3x, A4x v 2985-CTO, CEx, CFx, CGx, CKx, CLx, CWx, CYx, D2x, D3x, D8x, DCx, DHx, DZx, E2x, E3x, E4x, E5x, EAx, EJx, R4x v 3093-CTO, 2Sx, 2Tx, 34x, 35x, 36x, 37x, 38x, 3Gx, 3Hx v 3113-CTO...
Page 202
Table 38. Parts list—Overall (continued) FRU no. SATA hard disk drive, 100 GB, 7,200 rpm 39T2799 v 4184-CTO v 7448-CTO v 7449-CTO, 99x v 7450-CTO, 26x, 8Zx, 95x v 7453-CTO v 2263-CTO v 2266-CTO SATA hard disk drive, 160 GB , 7,200 rpm OP 42T1461 v 4184-CTO v 7448-CTO, 3Hx 3Nx...
Page 203
Table 38. Parts list—Overall (continued) FRU no. SATA hard disk drive, 200 GB, FDE, 7,200 rpm OP 42T1463 v 4184-CTO v 7448-CTO v 7449-CTO, 8Lx, 9Cx v 7450-CTO, 8Mx, 94x, 9Qx, EMx, FHx v 7453-CTO v 2263-CTO v 2266-CTO SATA hard disk drive, 250 GB, FDE, 7,200 rpm 42T1563 v 4184-CTO v 7448-CTO...
Page 204
Table 38. Parts list—Overall (continued) FRU no. SATA hard disk drive, 250 GB, FDE, 7,200 rpm 45N7259 v 0053-CTO v 0831-CTO v 2985-CTO v 3093-CTO v 3113-CTO v 3144-CTO v 3239-CTO SATA hard disk drive, 320 GB, 7,200 rpm 42T1559 v 4184-CTO v 7448-CTO, 3Jx v 7449-CTO, 47x, 4Ex, 4Fx, 4Lx, 4Mx, 4Nx...
Page 205
Table 38. Parts list—Overall (continued) FRU no. SATA hard disk drive, 500 GB, 7,200 rpm 45N7257 v 4184-CTO v 7448-CTO, 3Kx, 3Mx v 7449-CTO, 4Jx v 7450-CTO, 6Lx, 6Px, 6Wx, D3x, D5x, D6x v 7453-CTO v 2263-CTO v 2266-CTO v 0053-CTO, 77x v 0831-CTO v 2985-CTO, CHx, CJx, CMx, CNx, CPx, CRx, CSx, CTx, CUx, CVx, CZx, D1x, D4x, D5x, D6x, D7x, D9x, DAx, DBx, EEx...
Page 206
Table 38. Parts list—Overall (continued) FRU no. SATA solid state drive, 64 GB 41W0520 v 4184-CTO, E9x, ESx v 7448-CTO, EAx, EUx v 7449-CTO, EAx, EUx v 7450-CTO, 8Tx, E9x, ERx, ESx, ETx, G7x v 7453-CTO, E9x, ESx v 2263-CTO v 2266-CTO SATA solid state drive, 64 GB 45N8201...
Page 207
Table 38. Parts list—Overall (continued) FRU no. SATA solid state drive, 128 GB 45N7953 v 0053-CTO v 0831-CTO v 2985-CTO v 3093-CTO, 26x v 3113-CTO v 3144-CTO v 3239-CTO SATA solid state drive, 128 GB, FDE 45N8205 v 4184-CTO v 7448-CTO v 7449-CTO v 7450-CTO v 7453-CTO...
Page 208
Table 38. Parts list—Overall (continued) FRU no. ThinkPad X200 UltraBase 42X4963 v 4184-CTO v 7448-CTO, 3Bx, 3Cx, 3Dx v 7449-CTO, 45x, 47x, 4Ax, 4Bx, 4Wx, 84x, 88x, 8Fx, 8Jx, 8Rx, 8Sx, 9Fx, CCx, EKx v 7450-CTO, 67x, 6Mx, 6Nx, 6Xx, 6Yx, 8Kx, 8Ux, 9Rx, DFx, EQx, F8x, FHx, FJx, GVx, H8x v 7453-CTO, EQx v 2263-CTO v 2266-CTO...
Page 209
Table 38. Parts list—Overall (continued) FRU no. DVD/CD-RW combo drive 42T2611 v 4184-CTO v 7448-CTO v 7449-CTO v 7450-CTO v 7453-CTO v 2263-CTO v 2266-CTO DVD-RAM/RW drive 42T2545 v 4184-CTO v 7448-CTO, 3Bx, 3Cx, 3Dx v 7449-CTO, 45x, 47x, 4Ax, 4Bx, 4Wx, 84x, 88x, 8Fx, 8Jx, 8Rx, 8Sx, 9Fx, CCx, EKx v 7450-CTO, 67x, 6Mx, 6Nx, 6Xx, 6Yx, 8Kx, 8Ux, 9Rx, DFx, EQx, F8x, FHx, FJx, H8x v 7453-CTO, EQx v 2263-CTO...
Page 210
Table 38. Parts list—Overall (continued) FRU no. DVD-RAM/RW drive 45N7451 v 4184-CTO v 7448-CTO, 3Bx, 3Cx, 3Dx v 7449-CTO, 45x, 47x, 4Ax, 4Bx, 4Wx, 84x, 88x, 8Fx, 8Jx, 8Rx, 8Sx, 9Fx, CCx, EKx v 7450-CTO, 67x, 6Mx, 6Nx, 6Xx, 6Yx, 8Kx, 8Ux, 9Rx, DFx, EQx, F8x, FHx, FJx, H8x v 7453-CTO, EQx v 2263-CTO v 2266-CTO...
Page 211
Table 38. Parts list—Overall (continued) FRU no. Blu-Ray disk drive 45N7459 v 0053-CTO v 0831-CTO v 2985-CTO v 3093-CTO v 3113-CTO v 3144-CTO v 3239-CTO DIMM door kit 44C9555 Base cover assembly for 4184 60Y4611 Base cover assembly for 7448 60Y4612 Base cover assembly for 7449 60Y4613...
Page 218
Table 39. Parts list—12.1-in. WXGA TFT for touch panel LCD or direct-bonding glass LCD (continued) FRU no. LCD panel, 12.1-in. WXGA, LED backlight for direct-bonding glass 13N7272 v 4184-CTO v 7448-CTO v 7449-CTO, 4Hx, 4Zx, C7x, C8x, CAx, CBx v 7450-CTO, 64x, 65x, 67x, 69x, 6Bx, 6Cx, 6Nx, 6Yx, D4x, D5x, D6x, DAx, DCx, DFx v 7453-CTO, 69x, 6Bx v 2263-CTO v 2266-CTO...
Page 219
Table 39. Parts list—12.1-in. WXGA TFT for touch panel LCD or direct-bonding glass LCD (continued) FRU no. LCD bracket L and R for direct-bonding glass 60Y4165 v 4184-CTO v 7448-CTO v 7449-CTO, 4Hx, 4Zx, C7x, C8x, CAx, CBx v 7450-CTO, 64x, 65x, 67x, 69x, 6Bx, 6Cx, 6Nx, 6Yx, D4x, D5x, D6x, DAx, DCx, DFx v 7453-CTO, 69x, 6Bx v 2263-CTO v 2266-CTO...
Page 222
Table 39. Parts list—12.1-in. WXGA TFT for touch panel LCD or direct-bonding glass LCD (continued) FRU no. Wireless LAN/WAN/USB antenna assembly 43Y9828 v 4184-CTO, H4x, H6x v 7448-CTO, H3x, H5x v 7449-CTO v 7450-CTO v 7453-CTO v 2263-CTO v 2266-CTO Wireless LAN/WAN/USB antenna assembly 43Y9829 v 4184-CTO, H4x, H6x...
Page 230
Table 40. Parts list—12.1-in. WXGA TFT for protection plate LCD (continued) FRU no. Wireless LAN/WAN/USB antenna assembly 43Y9828 v 4184-CTO v 7448-CTO v 7449-CTO v 7450-CTO v 7453-CTO v 2263-CTO v 2266-CTO Wireless LAN/WAN/USB antenna assembly 43Y9829 v 4184-CTO v 7448-CTO v 7449-CTO v 7450-CTO v 7453-CTO...
Keyboard Table 41. Parts list—Keyboard Language CRU ID Arabic 42T3752 42T3686 Belgian 42T3749 42T3683 Brazilian Portuguese 42T3768 42T3702 Bulgarian 42T4143 42T4139 Canadian French (058) 42T3739 42T3673 Canadian French (Acnor) 42T3738 42T3672 Czech 42T3757 42T3691 Danish 42T3746 42T3680 Dutch 42T3743 42T3677 Finnish, Swedish 42T3744 42T3678...
Miscellaneous parts Table 42. Parts list—Miscellaneous parts Screw kit: 45N3139 v M1.6 × 6 mm (sliver), wafer head (1) v M2 × 2.5 mm (black), wafer head (1) v M2 × 3 mm (black), flat head (11) v M2 × 3.5 mm (silver), wafer head (18) v M2 ×...
Page 234
Table 42. Parts list—Miscellaneous parts (continued) Screw kit: 60Y4164 v M1.6 × 6 mm (sliver), wafer head (1) v M2 × 2.5 mm (black), wafer head (1) v M2 × 3 mm (black), flat head (11) v M2 × 3.5 mm (silver), wafer head (17) v M2 ×...
Page 235
Table 42. Parts list—Miscellaneous parts (continued) System board miscellaneous parts kit 45N3395 v (a) LCM top shielding assembly v VGA I/O bracket assembly v Heat sink holder assembly for LV/ULV v Hex screw with washer Note: Italicized letters in parentheses are references to the exploded view in “Overall” on page 174.
Power cords A ThinkPad power cord for a specific country or region is usually available only in that country or region: Table 44. Parts list—2-pin power cords Country or region FRU no. Argentina 42T5020 42T5105 * v models -CTO, xxY Brazil 42T5180 42T5183 v models -CTO, xxP...
Recovery discs Windows XP Tablet DVDs (32 bit) Windows XP Tablet (32 bit) is preinstalled as the operating system in the following models: v 4184-CTO, F5x, F8x, FCx, FGx, GMx, GNx v 7448-CTO, 36x, 3Ax, 3Hx, 8Wx, F5x, F8x, FCx, FGx, GMx, GNx v 7449-CTO, 43x, 45x, 47x, 49x, 4Ax, 4Lx, 4Nx, 84x, 8Fx, 8Jx, 8Rx, 9Ex, 9Fx, CCx, EYx, F9x, FNx v 7450-CTO, 2Hx, 2Lx, 63x, 67x, 6Ax, 6Ex, 6Gx, 6Hx, 9Gx, D7x, D8x, D9x, DAx,...
Page 239
v 0053-CTO v 0831-CTO v 2985-CTO, C8x, CAx, CGx, CKx, CLx, CYx, D2x, D3x v 3093-CTO v 3113-CTO v 3144-CTO v 3239-CTO Table 47. Parts list—Windows XP Tablet (32 bit) recovery DVDs Language English 76Y1314 English (modem-disabled) 76Y1313 French 76Y1304 German 76Y1305 Italian...
Windows Vista Home Premium (32 bit) DVDs Windows Vista Home Premium (32 bit) is preinstalled as the operating system in the following models: v 4184-CTO, 25x, 2Vx, 53x, 54x, 8Ex, 97x v 7448-CTO, 2Ex, 8Dx, 8Vx, 9Dx, 9Kx, 9Lx v 7449-CTO, 25x v 7450-CTO, 25x v 7453-CTO, 25x v 2263-CTO...
Windows Vista Business (32 bit) DVDs Windows Vista Business (32 bit) is preinstalled as the operating system in the following models: v 4184-CTO, E4x, E6x, E7x, E9x, EFx, EGx, ENx, ESx, F4x, F7x, FBx, FFx, H4x, H6x v 7448-CTO, 8Xx, E3x, E5x, E8x, EAx, EEx, EHx, EPx, EUx, F3x, F6x, FAx, FEx, FKx, G6x, H3x, H5x v 7449-CTO, 2Jx, 2Rx, 2Tx, 4Bx, 88x, 8Lx, 8Qx, 8Sx, 99x, 9Ax, 9Bx, 9Cx, 9Hx, E5x, E8x, EAx, EHx, EPx, EUx, EWx, FLx, FWx, FXx, G5x, G6x, GFx, GGx, GLx, GPx,...
Page 242
Table 49. Parts list—Windows Vista Business (32 bit) DVDs Language Brazilian Portuguese 58Y2997 Czech 58Y3000 Danish 58Y3001 English 58Y3023 English (modem-disabled) 58Y3022 English, Finnish, and Swedish (in Sweden) 58Y3025 English, French, German, and Dutch (in Belgium and Luxemburg) 58Y3024 English, French, German, and Italian (in Switzerland) 58Y3026 French 58Y3002...
Page 243
v 0053-CTO v 0831-CTO v 2985-CTO v 3093-CTO v 3113-CTO v 3144-CTO v 3239-CTO Table 50. Parts list—Windows Vista Business (32 bit) DVDs Language English 76Y1342 English (for India) 76Y1341 Parts list...
Windows Vista Business (64 bit) DVDs Windows Vista Business (64 bit) is preinstalled as the operating system in the following models: v 4184-CTO v 7448-CTO v 7449-CTO, 4Jx, EKx v 7450-CTO, 65x, 6Lx, 6Mx, 6Nx, 6Px, DFx, FYx, GVx v 7453-CTO v 2263-CTO v 2266-CTO Table 51.
Windows Vista Ultimate (32 bit) DVDs Windows Vista Ultimate (32 bit) is preinstalled as the operating system in the following models: v 4184-CTO v 7448-CTO, 2Qx v 7449-CTO, 2Qx v 7450-CTO, 2Kx v 7453-CTO, 2Kx v 2263-CTO v 2266-CTO Table 52. Parts list—Windows Vista Ultimate (32 bit) DVDs Language Czech 58Y3048...
Windows 7 Home Basic (32 bit) DVDs Windows 7 Home Basic (32 bit) is preinstalled as the operating system in the following models: v 4184-CTO v 7448-CTO v 7449-CTO v 7450-CTO v 7453-CTO v 2263-CTO v 2266-CTO Table 53. Parts list—Windows 7 Home Basic (32 bit) DVDs Language Brazilian Portuguese 58Y3907...
Windows 7 Home Premium (32 bit) DVDs Windows 7 Home Premium (32 bit) is preinstalled as the operating system in the following models: v 4184-CTO v 7448-CTO, 3Ex v 7449-CTO, 4Xx, 4Yx v 7450-CTO, 6Wx v 7453-CTO v 2263-CTO v 2266-CTO Table 54.
Page 248
v 0053-CTO, 74x, 75x, 76x v 0831-CTO, A2x, A3x, A4x v 2985-CTO, CPx, D6x v 3093-CTO v 3113-CTO v 3144-CTO v 3239-CTO Table 55. Parts list—Windows 7 Home Premium (32 bit) DVDs Language English 76Y1444 English (for India) 76Y1438 Japanese 76Y1440 Korean 76Y1441...
Windows 7 Home Premium (64 bit) DVDs Windows 7 Home Premium (64 bit) is preinstalled as the operating system in the following models: v 4184-CTO v 7448-CTO v 7449-CTO v 7450-CTO v 7453-CTO v 2263-CTO v 2266-CTO Table 56. Parts list—Windows 7 Home Premium (64 bit) DVDs Language English 58Y3936...
Windows 7 Professional (32 bit) DVDs Windows 7 Professional (32 bit) is preinstalled as the operating system in the following models: v 4184-CTO v 7448-CTO, 34x, 38x, 3Fx, 3Gx, 3Jx, 3Kx, 3Lx, 3Mx v 7449-CTO, 44x, 4Cx, 4Dx, 4Ex, 4Fx, 4Gx, 4Hx, 4Kx, 4Mx, 4Px, 4Qx, 4Rx, 4Sx, 4Tx, 4Ux, 4Vx, 4Wx, 4Zx, C3x, C4x, C5x, C6x, C7x, C8x, C9x, CAx, CBx v 7450-CTO, 6Dx, 6Fx, 6Qx, 6Rx, 6Sx, 6Tx, 6Vx, 6Zx, D3x, D4x, D5x, D6x, DEx v 7453-CTO, Z3x, Z4x, Z5x...
Page 251
Table 58. Parts list—Windows 7 Professional (32 bit) DVDs Language Brazilian Portuguese 58Y3862 Czech 58Y3865 Danish 58Y3866 English 58Y3889 English (modem-disabled) 58Y3888 English (for India) 58Y3867 English, Finnish, and Swedish (in Sweden) 58Y3891 English, French, German, and Dutch (in Belgium and Luxemburg) 58Y3890 English, French, German, and Italian (in Switzerland) 58Y3892...
Page 253
Table 59. Parts list—Windows 7 Professional (32 bit) DVDs Language Brazilian Portuguese 76Y1345 Czech 76Y1348 Danish 76Y1349 English 76Y1372 English (modem-disabled) 76Y1371 English (for India) 76Y1350 English, Finnish, and Swedish (in Sweden) 76Y1374 English, French, German, and Dutch (in Belgium and Luxemburg) 76Y1373 English, French, German, and Italian (in Switzerland) 76Y1375...
Windows 7 Professional (64 bit) DVDs Windows 7 Professional (64 bit) is preinstalled as the operating system in the following models: v 4184-CTO v 7448-CTO, 3Nx v 7449-CTO v 7450-CTO, 6Xx, 6Yx, DBx, DCx, DDx v 7453-CTO, DDx v 2263-CTO v 2266-CTO Table 60.
Page 255
v 0053-CTO v 0831-CTO v 2985-CTO, CDx, CJx, CRx, CUx, D1x, D7x, DAx, DRx, DSx, DTx, DUx, DVx, DWx, E3x, ESx, ETx v 3093-CTO, 2Nx, 2Px, 2Rx, 2Wx, 36x, 3Tx, 3Ux, 3Yx v 3113-CTO v 3144-CTO v 3239-CTO Table 61. Parts list—Windows 7 Professional (64 bit) DVDs Language Danish 76Y1488...
USB floppy diskette drive tool kit 27L3452 Test card for integrated Smart Card 42W7820 ThinkPad Hardware Maintenance Diskette Version 1.73 or later — Note: Download the file from the following Web site: http://www.lenovo.com/ ThinkPad X200 Tablet and X201 Tablet Hardware Maintenance Manual...
Actual results may vary. Users of this document should verify the applicable data for their specific environment. Trademarks The following terms are trademarks of Lenovo in the United States, other countries or both: Active Protection System ®...
Page 260
Part Number: 45N3683_03 (1P) P/N: 45N3683_03...