Dell DR4000 Release Notes
Release 1.0
Hide thumbs
Also See for DR4000:
- Owner's manual (156 pages) ,
- Glossary (151 pages) ,
- Administrator's manual (144 pages)
Advertisement
Quick Links
Advertisement
Related Manuals for Dell DR4000
Summary of Contents for Dell DR4000
-
Page 1: Release Notes
Dell DR4000 System Release 1.0 Release Notes... -
Page 2: Notes, Cautions, And Warnings
© 2012 Dell Inc. All rights reserved. Reproduction of these materials in any manner whatsoever without the written permission of Dell Inc. is strictly forbidden. Trademarks used in this text: Dell™, the DELL logo, and DR4000™ are trademarks of Dell Inc. ® ®... -
Page 3: Supported Software And Hardware
Source Code Availability A portion of the DR4000 system software may contain or consist of open source software, which you can use under the terms and conditions of the specific license under which the open source software is distributed. - Page 4 Known Issues and Resolutions This section explains the known issues, descriptions, status, and any workaround for the DR4000 system software. Table 1. Known Best Practices Issues and Workarounds for Release 1.0 Issue Description Workaround/Solution 4051 If you must use the CLI system --...
- Page 5 DR4000 system should start up displayed. with all services running normally. 8897 Currently, the DR4000 system can Initiate the reboot of the DR4000 DR4000 and encounter some low-level system system using either of the two iDRAC reboot management coordination following choices:...
- Page 6 NVRAM in the fails with: procedure for powering off the DR4000 system, observe the NVRAM DR4000 system and waiting for the following best practice for ’write ready’ NVRAM to properly discharge is shutting down the DR4000 time out not followed.
- Page 7 (restoring original source and target destinations). Under this scenario, a fraction of the data to be recovered is sent across the WAN link. This could speed up a remote restore significantly. DR4000 System Release Notes, Release 1.0...
- Page 8 However, there are some Reverse the tape backup to the original downsides: replication location (first back to the DR4000 • If step 1 is not followed replica container, and then back to correctly, any changes not fully supported on the original source location of the replicated are lost.
- Page 9 During the filesystem initialization, when the data is no longer the mkfs.vxfs are not properly needed. unmounting all the snapshots. NOTE: Contact Dell Support for assistance prior to using the RM program. DR4000 System Release Notes, Release 1.0...
- Page 10 Use only the hostname, and send Relay server e-mail to receive system alerts from test e-mail messages to verify does not the DR4000 system, the relay host that e-mails are received by all work as IP or has to be configured. When recipients.
- Page 11 This update can only container name (FQDN) for a remote take place when the remote whose IP is DR4000 system, and the IP address DR4000 system is also active changed is has been changed because of a because this is a synchronous offline.
- Page 12 Post Deduplication and Deduplication Savings updated after the cleaner operation is completed. 8583 When a target DR4000 system in a The only workaround is to rely Replication source-target pair enters on system alerts and down event...
- Page 13 5995 The best practice when using Make sure that replication is A potential multiple DR4000 containers for enabled for all of the DR4000 data issue can performing a single CommVault containers that are involved in occur when (CV) backup and using the the CV backup.
- Page 14 NFS once it This issue will be fixed in the has been next scheduled release of the created. DR4000 system. DR4000 System Release Notes, Release 1.0...
- Page 15 Related DR4000 System Documentation For a complete list of the released documentation that supports the Dell DR4000 system, see the latest available versions at support.dell.com/manuals. This product is supported by the following Dell documentation: •...
- Page 16 DR4000 System Release Notes, Release 1.0...