hit counter script
Lenovo IdeaCentre K4 Series Hardware Maintenance Manual
  1. Manuals
  2. Brands
  3. Lenovo Manuals
  4. Desktop
  5. IdeaCentre K4 Series
  6. Hardware maintenance manual
Lenovo IdeaCentre K4 Series Hardware Maintenance Manual

Lenovo IdeaCentre K4 Series Hardware Maintenance Manual

Ideacentre k4 series
Hide thumbs Also See for IdeaCentre K4 Series:
Table of Contents

Advertisement

Quick Links

See also: User Manual
IdeaCentre K4 Series
Hardware Maintenance Manual
Machine Types: 10086/3109/4743 K430; 10089/1168/4744 K410;
10090/2556/4748 K415

Advertisement

Table of Contents
loading

Related Manuals for Lenovo IdeaCentre K4 Series

Summary of Contents for Lenovo IdeaCentre K4 Series

  • Page 1 IdeaCentre K4 Series Hardware Maintenance Manual Machine Types: 10086/3109/4743 K430; 10089/1168/4744 K410; 10090/2556/4748 K415...
  • Page 3 IdeaCentre K4 Series Hardware Maintenance Manual Machine Types: 10086/3109/4743 K430; 10089/1168/4744 K410; 10090/2556/4748 K415...
  • Page 4 First Edition (April 2013)18st © Copyright Lenovo 2013. LIMITED AND RESTRICTED RIGHTS NOTICE: If data or software are delivered pursuant a General Services Administration “GSA” contract, use, reproduction, or disclosure is subject to restrictions set forth in Contract No. GS-35F-05925...

  • Page 5: Table Of Contents

    Replacing the motherboard..Exiting the Lenovo BIOS Setup Utility program . . FRU lists ....
  • Page 6 IdeaCentre K4 SeriesHardware Maintenance Manual...

  • Page 7: Chapter 1. About This Manual

    This manual contains service and reference information for IdeaCentre K430 & K410 computers listed on the cover. It is intended only for trained servicers who are familiar with Lenovo computer products. Before servicing a Lenovo product, be sure to read the Safety Information.
  • Page 8 IdeaCentre K4 SeriesHardware Maintenance Manual...

  • Page 9: Chapter 2. Safety Information

    Electrical current from power, telephone, and communication cables can be hazardous. To avoid personal injury or equipment damage, disconnect the attached power cords, telecommunication systems, networks, and modems before you open the computer covers, unless instructed otherwise in the installation and configuration procedures. © Copyright Lenovo 2013...
  • Page 10 Observe the following rules when working on electrical equipment. Important: Use only approved tools and test equipment. Some hand tools have handles covered with a soft material that does not insulate you when working with live electrical currents. Many customers have, near their equipment, rubber floor mats that contain small conductive fibers to decrease electrostatic discharges.

  • Page 11: Safety Inspection Guide

    – Send another person to get medical aid. Safety inspection guide The intent of this inspection guide is to assist you in identifying potentially unsafe conditions on these products. Each machine, as it was designed and built, had required safety items installed to protect users and service personnel from injury.

  • Page 12: Grounding Requirements

    • Avoid contact with other people while handling the part. • Wear a grounded wrist strap against your skin to eliminate static on your body. • Prevent the part from touching your clothing. Most clothing is insulative and retains a charge even when you are wearing a wrist strap.
  • Page 13 To Connect To Disconnect 1. Turn everything OFF. 1. Turn everything OFF. 2. First, attach all cables to devices. 2. First, remove power cords from outlet. 3. Attach signal cables to connectors. 3. Remove signal cables from connectors. 4. Attach power cords to outlet. 4.
  • Page 14 ≥18 kg(37 lbs) ≥32 kg(70.5 lbs) ≥55 kg(121.2 lbs) CAUTION: Use safe practices when lifting. CAUTION: The power control button on the device and the power switch on the power supply do not turn off the electrical current supplied to the device. The device also might have more than one power cord.

  • Page 15: Chapter 3. General Information

    This section lists the physical specifications. Environment Air temperature: Operating: 10° to 35°C Transit: -20° to 55°C Humidity: Operating: 35% to 80% Transit: 20% to 90% (40°C) Altitude: 86KPa to 106KPa Electrical input: Input voltage: 90V-264V(AC) Input frequency: 47Hz-63Hz © Copyright Lenovo 2013...
  • Page 16 IdeaCentre K4 SeriesHardware Maintenance Manual...

  • Page 17: Chapter 4. General Checkout

    • If the computer displays a POST error, go to “POST error codes”. • If the computer hangs and no error is displayed, continue at step 7. 7. If the test stops and you cannot continue, replace the last device tested. © Copyright Lenovo 2013...
  • Page 18 IdeaCentre K4 SeriesHardware Maintenance Manual...

  • Page 19: Chapter 5. Using The Setup Utility

    1. If your computer is already on when you start this procedure, shut down the operating system and turn off the computer. 2. Press and hold the F1 key then turn on the computer. When the Lenovo BIOS Setup Utility program is displayed, release the F1 key.
  • Page 20 5. Select Save changes and Exit from the menu. Power-On Password When a Power-On Password is set, you cannot start the Lenovo BIOS Setup Utility program until a valid password is typed from the keyboard. Setting, changing, or deleting a Power-On Password Note: A password can be any combination of letters and numbers up to 16 character (a-z, and 0-9).

  • Page 21: Enabling Or Disabling A Device

    To set a Power-On Password, do the following: 1. Start the Lenovo BIOS Setup Utility program (See ”Starting the Lenovo BIOS Setup Utility program” on page 13.) 2. From the Security menu, select Set Power-On Password and press the Enter key.

  • Page 22: Selecting A Startup Device

    Selecting or changing the startup device sequence To view or permanently change the configured startup device sequence, do the following: 1. Start the Lenovo BIOS Setup Utility program (see “Starting the Lenovo BIOS Setup Utility program” on page 13). 2. From the Lenovo BIOS Setup Utility program main menu, select the Startup option.

  • Page 23: Exiting The Lenovo Bios Setup Utility Program

    Exiting the Lenovo BIOS Setup Utility program After you finish viewing or changing settings, press the Esc key to return to the Lenovo BIOS Setup Utility program main menu. You might have to press the Esc key several times. Do one of the following: •...
  • Page 24 IdeaCentre K4 SeriesHardware Maintenance Manual...

  • Page 25: Chapter 6. Symptom-To-Fru Index

    Check that the following are properly installed: Reseat connectors • Power Cord • On/Off Switch connector • System Board Power Supply connectors • Microprocessor(s) connection Check the power cord. Power Cord Check the power-on switch. Power-on Switch © Copyright Lenovo 2013...

  • Page 26: Post Error Codes

    POST error codes Each time you turn the computer on, it performs a series of tests to check that the system is operating correctly and that certain options are set. This series of tests is called the Power-On Self-Test, or POST. POST does the following: •...

  • Page 27: Chapter 7. Locations

    The system board (also known as the “mainboard” or “motherboard”) is the main circuit board in your computer. It provides basic computer functions and supports a variety of devices that are factory-installed or that you can install later. The following illustrations show the locations of the different parts on the system board. © Copyright Lenovo 2013...
  • Page 28 IdeaCentre K430 12V power connector Front USB connector Microprocessor and heat sink Front USB connector Microprocessor fan connector Mode SW connector Memory slots (4) Serial (COM2)connector Power connector Battery Mini PCI Express slot LPC debug connector Front audio connector PCI Express × 16 adapter slots (2) Power fan header PCI Express ×...
  • Page 29 IdeaCentre K410 12V power connector Power fan header Microprocessor and heat sink Front panel connector Microprocessor fan connector Clear CMOS jumper Memory slots (2) Front USB connectors (2) Thermal sensor header connector Mini PCI Express slot Power connector PCI Express × 1 adapter slots (3) Battery Front audio connector SATA connectors (3)
  • Page 30 IdeaCentre K415 12V power connector SATA connectors (4) Battery Serial (COM2)connector Microprocessor and heat sink Front panel connector Microprocessor fan connector Mode switch header Memory slots (4) SPI Debug Thermal sensor header connector Front USB connectors (2) Mini PCI Express × 1 Clear CMOS jumper Power connector Mini PCI Express ×...

  • Page 31: Chapter 8. Replacing Hardware

    Before proceeding with the disassembly procedure, make sure that you do the following: 1. Turn off the power to the system and all peripherals. 2. Unplug all power and signal cables from the computer. 3. Place the system on a flat, stable surface. © Copyright Lenovo 2013...

  • Page 32: Replacing The Keyboard And Mouse

    Replacing the keyboard and mouse Note: Your keyboard will be connected to a USB connector at either front or at the rear of the computer. To replace the keyboard: Step 1. Remove any media (disks, CDs, or memory cards) from the drives, shut down the computer, and turn off all attached devices.

  • Page 33: Removing The Front Bezel

    Step 5. Slide the computer cover out to remove it. Step 6. To reinstall the computer cover: Line up the computer cover with the chassis then slide it back. Secure the computer cover to the chassis with the screws. Removing the front bezel Note: For this procedure, it helps to lay the computer flat.

  • Page 34: Replacing A Memory Module

    Step 2. Remove the front bezel by releasing the three plastic tabs inside the chassis and sliding the bezel out as shown. Step 3. To reattach the bezel, align the plastic tabs on the bottom of the bezel with the corresponding holes in the chassis, and then snap it into position.

  • Page 35: Replacing A Hard Disk Drive

    Step 4. Position the new memory module over the memory connector. Make sure that the notch on the memory module aligns correctly with the connector key on the system board. Push the memory module straight down into the connector until the retaining clips close. Step 5.

  • Page 36: Replacing An Optical Drive

    Step 4. Remove the hard disk drive from the plastic bracket as shown. Step 5. Line up the new hard disk drive with the plastic bracket and snap it into position. Step 6. Slide the new hard disk drive into the drive bay and slide the drive bay into place. Step 7.

  • Page 37: Replacing A Graphics Card

    Replacing a graphics card Note: For this procedure, it helps to lay the computer flat. To replace a graphics card: Step 1. Remove the computer cover. Refer to “Removing the computer cover”. Step 2. Follow the below steps to remove a graphics card: If your computer has a Duo-graphics cards installed, follow the steps below to replace it: Remove the screw that secures the Duo-graphics cards fixing bracket and lift the bracket up.
  • Page 38 Remove the screw that secures the graphics card latch to the chassis, open it, and remove the Duo-graphics cards connector. Remove the graphics card by pulling it straight out of the connector. If your computer has a single graphics card installed, follow the steps below to replace it: IdeaCentre K4 SeriesHardware Maintenance Manual...

  • Page 39: Replacing The Tv-Tuner Card

    Remove the screw that secures the graphics latch to the chassis and open it. Remove the graphics card by pulling it straight out of the connector. Step 3. Install the new adapter into the same adapter connector. Step 4. Turn the graphics card latch to the closed position and secure it with the screw. Step 5.
  • Page 40 To replace the TV-Tuner card: Step 1. Remove the computer cover. Refer to “Removing the computer cover”. 1 2 3 Step 2. Remove the screw that secures the graphics card latch to the chassis and open it. Step 3. Remove the TV-Tuner card by pulling it straight out of the connector. Step 4.

  • Page 41: Replacing The Power Supply

    Step 6. Reattach the computer cover. Replacing the Power supply Note: For this procedure, it helps to lay the computer flat. To replace the Power supply: Step 1. Remove any media (disks, CDs, DVDs, or memory cards) from the drives, shut down the operating system, and turn off the computer and all attached devices.

  • Page 42: Replacing The Heat-Sink

    Step 1. Remove any media (disks, CDs, DVDs, or memory cards) from the drives, shut down the operating system, and turn off the computer and all attached devices. Step 2. Unplug all power cords from electrical outlets. Step 3. Disconnect all cables attached to the computer. This includes power cords, input/output (I/O) cables, and any other cables that are connected to the computer.

  • Page 43: Replacing The Cpu

    Step 3. Disconnect all cables attached to the computer. This includes power cords, input/output (I/O) cables, and any other cables that are connected to the computer. Refer to “Left and right view” and “Rear view” for help with locating the various connectors. Step 4.
  • Page 44 Step 4. Remove the computer cover. Refer to “Removing the computer cover”. Step 5. Remove the microprocessor fan. Refer to “Replacing the microprocessor fan”. Step 6. Remove the heat-sink. Refer to “Replacing the heat-sink”. Step 7. To remove the microprocessor from the system board, press then slide the small handle out to spring it up.

  • Page 45: Replacing The Wi-Fi Card

    Step 8. Holding the sides of the microprocessor with your fingers, remove the protective cover that protects the gold contacts on the new microprocessor. Step 9. Holding the sides of the microprocessor with your fingers, position the microprocessor so that the notches on the microprocessor are aligned with the tabs in the microprocessor socket.

  • Page 46: Replacing The Motherboard

    To replace the Wi-Fi card: Step 1. Remove any media (disks, CDs, DVDs, or memory cards) from the drives, shut down the operating system, and turn off the computer and all attached devices. Step 2. Unplug all power cords from electrical outlets. Step 3.

  • Page 47: Fru Lists

    Step 2. Unplug all power cords from electrical outlets. Step 3. Disconnect all cables attached to the computer. This includes power cords, input/output (I/O) cables, and any other cables that are connected to the computer. Refer to “Left and right view” and “Rear view”...
  • Page 48 • 1– identifies parts that are fairly simple to replace, requiring few or no tools. • 2– identifies parts that are slightly more difficult to replace. • N-identifies parts that are not to be replaced by the customer. Description Lenovo P/N Processor I I73770K 3.5/1600/8/1155 77 E1 CPU 1100334 1100335 I I73770 3.4/1600/8/1155 77 E1 CPU...
  • Page 49 MT8JTF25664AZ-1G4D1 2GB DDRIII1333 RAM(R) 1007003 1100203 HMT351U6CFR8C-H9 4GB D3-1333 RAM-HF MT16KTF51264AZ-1G4M1 4GB D3-1333 RAM-HF 1100204 1100216 EBJ41UF8BDW0-GN-F 4GB D3-1600 RAM-HF Mic_R D9PFW 4GB DDRIII1333 RAM(R) 1100188 1100189 Mic_S D9PFW 4GB DDRIII1333 RAM(R) Psc_S A3P2GF3CKF-GDJ 4GB D3-1333 RAM(R) 1100154 1100007 Elp_R J2108BCSE-DJ-F 4GB DDRIII1333 RAM® M378B5273DH0-CH900 4GB DDRIII1333 RAM®...
  • Page 50 16200184 16200109 Samsung PM830 64G mSATA SSD Samsung PM830 128G mSATA SSD 16200110 Portable Hard Disk Drive 16005961 Lenovo Portable HardDrive(SP) F410(500G) Optical Drive 25011181 PLDS 16XDH16ABSH SATA Black DVDRWLH TSST 16XSH216AB SATA Black DVDRWLH 25200416 25200485 HLDS 16XGH70N SATA Black DVDRWLH...
  • Page 51 Bitland @Geforce GT 630@2G/A/DB/H Graphic Card 11200899 Power Supply HuntKey HK380-12GP S2(S7) ATX280W Power Supply 36-200158 36-200157 LiteonPS-5281-7VR5-RoHS ATX280W Power Supply AcBelPC6001-EL9G ATX280W Power Supply 36-200156 36-200161 FSP280-50EPA ATX280W 85% Power Supply LiteonPS-5281-02VA-RoHS ATX280W 85% Power Supply 36-200160 36-200159 AcBelPC9008-EL1G ATX280W 85% Power Supply AcBel PC7033-EL0G 450W NEW CABLE Power Supply(R) 36-001873 36001720...
  • Page 52 31024766 MSI graphics card SLI cable 31048424 ATI graphics card crossfire cable 31047520 JT Z75 MB rearIO shielding 31500766 Monitor 18200176 Lenovo Black LI2361dwA/TPV/A/R/WW Lenovo Black LI2361dwA/TPV/A/R/CN 18200177 18004685 Lenovo L2262wA/TPV/A/R/WW 0560HB1 Lenovo Black L2262wA/TPV/A/R/CN 18004767 18200125 Lenovo L2262w/TPV/A/R/WW/W3Y/S/D Lenovo Black L2062wA/TPV/A/R/WW...
  • Page 53 Mechanical JT LX319 K4 chassis card bracket 31500767 JT mobile HDD case 31501000 11200762 RoatonK4 Bitland mSATA Conversion Card JT SSD plastic bracket 31500999 31501076 JT M2X3 Dedicated Screw Chassis 90200579 JT LX-319CTA Front Bezel JT LX-319CTA Upper Bezel with Mode Switch & Power Botton 90200580 90200581 JT LX-319CTA ODD holder...
  • Page 54 Sunrex LXH-EKB-10YA(SP) B-Silk KB-LVT 25200509 25200510 Sunrex LXH-EKB-10YA(SL) B-Silk KB-LVT Sunrex LXH-EKB-10YA(NL) B-Silk KB-LVT 25200511 25200512 Sunrex LXH-EKB-10YA(IT) B-Silk KB-LVT Sunrex LXH-EKB-10YA(HB) B-Silk KB-LVT 25200513 25200514 Sunrex LXH-EKB-10YA(FR) B-Silk KB-LVT Sunrex LXH-EKB-10YA(BE) B-Silk KB-LVT 25200515 25200516 Sunrex LXH-EKB-10YA(GK) B-Silk KB-LVT Sunrex LXH-EKB-10YA(HG) B-Silk KB-LVT 25200517 25200518...
  • Page 55 Liteon SK-8861(IL) S-Silk KB-Black(WW) 90200714 90200715 Liteon SK-8861(FR) S-Silk KB-Black(WW) Liteon SK-8861(BE) S-Silk KB-Black(WW) 90200716 90200717 Liteon SK-8861(GR) S-Silk KB-Black(WW) Liteon SK-8861(HU) S-Silk KB-Black(WW) 90200718 90200719 Liteon SK-8861(BG) S-Silk KB-Black(WW) Liteon SK-8861(KR) S-Silk KB-Black(WW) 90200720 90200721 Liteon SK-8861(BR) S-Silk KB-Black(WW) Liteon SK-8861(JP) S-Silk KB-Black(WW) 90200722 90200723...
  • Page 56 IdeaCentre K4 SeriesHardware Maintenance Manual...

  • Page 57: Chapter 9. General Information

    • Wake Up on Alarm: You can specify a date and time at which the computer will be turned on automatically. This can be either a single event , a daily event or a weekly event. • Wake Up on LAN: This feature allows LAN adapter card to wake the System. © Copyright Lenovo 2013...

This manual is also suitable for:

Ideacentre k430 10086/3109/4743Ideacentre k41010089/1168/4744Ideacentre k415 10090/2556/4748

Table of Contents