Table of Contents
Advertisement
Cisco ATA 187 Analog Telephone Adaptor
Overview
This section describes the hardware and software features of the Cisco ATA 187 Analog Telephone
Adaptor (ATA 187) and includes a brief overview of the Session Initiation Protocol (SIP).
The ATA 187 analog telephone adaptors are handset-to-Ethernet adaptors that allow regular analog
phones to operate on IP-based telephony networks. The ATA 187 support two voice ports, each with an
independent phone number. The ATA 187 also has an RJ-45 10/100BASE-T data port.
This section covers these topics:
Session Initiation Protocol Overview, page 1-2
•
Hardware Overview, page 1-5
•
•
Software Features, page 1-5
•
Installation and Configuration Overview, page 1-9
Figure 1-1
OL-21862-01
Cisco Analog Telephone Adaptor
Cisco ATA 187 Analog Telephone Adaptor Administration Guide for SIP (Version 1.0)
1
C H A P T E R
1-1
Advertisement
Table of Contents
Related Manuals for Cisco ATA 187
Summary of Contents for Cisco ATA 187
- Page 1 The ATA 187 analog telephone adaptors are handset-to-Ethernet adaptors that allow regular analog phones to operate on IP-based telephony networks. The ATA 187 support two voice ports, each with an independent phone number. The ATA 187 also has an RJ-45 10/100BASE-T data port.
-
Page 2: Session Initiation Protocol Overview
Cisco ATA 187 Analog Telephone Adaptor Overview Session Initiation Protocol Overview The ATA187, which operates with Cisco voice-packet gateways, makes use of broadband pipes that are deployed through a digital subscriber line (DSL), fixed wireless-cable modem, and other Ethernet connections. -
Page 3: Components Of Sip
SIP servers can interact with other application services, such as Lightweight Directory Access Protocol Note (LDAP) servers, a database application, or an extensible markup language (XML) application. These application services provide back-end services such as directory, authentication, and billable services. Cisco ATA 187 Analog Telephone Adaptor Administration Guide for SIP (Version 1.0) OL-21862-01... -
Page 4: Sip Clients
LAN side and the switched-circuit network side. Phones—Can act as either a UAS or UAC. The ATA 187 can initiate SIP requests and respond to •... - Page 5 The ATA 187 has one network port—an RJ-45 10/100BASE-T data port to connect an • Ethernet-capable device, such as a computer, to the network. The ATA 187 performs auto-negotiation for duplexity and speed and is capable of 10/100 Mbps, Note full-duplex operation.
-
Page 6: Secure Real-Time Transport Protocol
INVITE message, the call is established to switch from voice mode to T.38 mode. Cisco Unified Communications Administration allows you to configure a SIP profile that supports T.38 fax communication. Voice Codecs Supported The ATA 187 supports these voice codecs (check your other network devices for the codecs they support): G.711µ-law •... -
Page 7: Ata 187 Sip Services
Type of Service (ToS) configuration for audio and signaling ethernet packets • Debugging and diagnostic tools • Modem Standards The ATA 187 supports the following modem standards: V.90 • V.92 • Cisco ATA 187 Analog Telephone Adaptor Administration Guide for SIP (Version 1.0) OL-21862-01... -
Page 8: Fax Services
• V.23 • Fax Services The ATA 187 supports two modes of fax services, in which fax signals are transmitted using the G.711 codec: Fax pass-through mode—Receiver-side Called Station Identification (CED) tone detection with • automatic G.711A-law or G.711µ-law switching. -
Page 9: Supplementary Services
Redial Installation and Configuration Overview Table 1-1 provides the basic steps required to install and configure the ATA 187 to make it operational in a typical SIP environment where a large number of ATA 187s must be deployed. Table 1-1... - Page 10 Chapter 1 Cisco ATA 187 Analog Telephone Adaptor Overview Installation and Configuration Overview Cisco ATA 187 Analog Telephone Adaptor Administration Guide for SIP (Version 1.0) 1-10 OL-21862-01...