Page 1
ND-45669 (E) ISSUE 2 PART OF STOCK # 151901 ® Command Manual DECEMBER, 1997 NEC America, Inc.
Page 2
NEC America, Inc. reserves the right to change the specifications, functions, or features, at any time, without notice. NEC America, Inc. has prepared this document for use by its em- ployees and customers. The information contained herein is the property of NEC America, Inc. and shall not be reproduced without prior written approval from NEC America, Inc.
Page 3
ADD. No. ADD. No. PAGE No. PAGE No. 44-1 44-2 ADDENDUM-001 ADDENDUM-002 ADDENDUM-003 ADDENDUM-004 DATE AUGUST, 1998 DATE JANUARY, 1999 DATE DATE ADDENDUM-005 ADDENDUM-006 ADDENDUM-007 ADDENDUM-008 DATE DATE DATE DATE NEAX2000 IVS Command Manual Addendum Revision Sheet 1/7 ND-45669 (E) ISSUE 2...
Page 4
ADD. No. ADD. No. PAGE No. PAGE No. 70-1 70-2 74-1 74-2 110-1 110-2 77-1 77-2 ADDENDUM-001 ADDENDUM-002 ADDENDUM-003 ADDENDUM-004 DATE AUGUST, 1998 DATE JANUARY, 1999 DATE DATE ADDENDUM-005 ADDENDUM-006 ADDENDUM-007 ADDENDUM-008 DATE DATE DATE DATE NEAX2000 IVS Command Manual Addendum Revision Sheet 2/7 ND-45669 (E) ISSUE 2...
Page 5
ADD. No. ADD. No. PAGE No. PAGE No. 140-1 174-1 140-2 174-2 188-1 188-2 156-1 156-2 199-1 199-2 ADDENDUM-001 ADDENDUM-002 ADDENDUM-003 ADDENDUM-004 DATE AUGUST, 1998 DATE JANUARY, 1999 DATE DATE ADDENDUM-005 ADDENDUM-006 ADDENDUM-007 ADDENDUM-008 DATE DATE DATE DATE NEAX2000 IVS Command Manual Addendum Revision Sheet 3/7 ND-45669 (E) ISSUE 2...
Page 6
ADD. No. ADD. No. PAGE No. PAGE No. 216-1 216-2 ADDENDUM-001 ADDENDUM-002 ADDENDUM-003 ADDENDUM-004 DATE AUGUST, 1998 DATE JANUARY, 1999 DATE DATE ADDENDUM-005 ADDENDUM-006 ADDENDUM-007 ADDENDUM-008 DATE DATE DATE DATE NEAX2000 IVS Command Manual Addendum Revision Sheet 4/7 ND-45669 (E) ISSUE 2...
Page 7
ADD. No. ADD. No. PAGE No. PAGE No. 327-1 327-2 327-3 327-4 311-1 311-2 ADDENDUM-001 ADDENDUM-002 ADDENDUM-003 ADDENDUM-004 DATE AUGUST, 1998 DATE JANUARY, 1999 DATE DATE ADDENDUM-005 ADDENDUM-006 ADDENDUM-007 ADDENDUM-008 DATE DATE DATE DATE NEAX2000 IVS Command Manual Addendum Revision Sheet 5/7 ND-45669 (E) ISSUE 2...
Page 8
ADD. No. ADD. No. PAGE No. PAGE No. ADDENDUM-001 ADDENDUM-002 ADDENDUM-003 ADDENDUM-004 DATE AUGUST, 1998 DATE JANUARY, 1999 DATE DATE ADDENDUM-005 ADDENDUM-006 ADDENDUM-007 ADDENDUM-008 DATE DATE DATE DATE NEAX2000 IVS Command Manual Addendum Revision Sheet 6/7 ND-45669 (E) ISSUE 2...
Page 9
ADD. No. ADD. No. PAGE No. PAGE No. ADDENDUM-001 ADDENDUM-002 ADDENDUM-003 ADDENDUM-004 DATE AUGUST, 1998 DATE JANUARY, 1999 DATE DATE ADDENDUM-005 ADDENDUM-006 ADDENDUM-007 ADDENDUM-008 DATE DATE DATE DATE NEAX2000 IVS Command Manual Addendum Revision Sheet 7/7 ND-45669 (E) ISSUE 2...
INTRODUCTION CHAPTER 1 INTRODUCTION 1. PURPOSE This manual provides descriptions of the commands required for programming the NEAX2000 IVS (PBX) us- ing the Customer Administration Terminal (CAT) or Maintenance Administration Terminal (MAT). 2. OUTLINE OF THE MANUAL This manual consists of the introduction (Chapter 1) and the following chapters: •...
Page 17
This page is for your notes. CHAPTER 1 ND-45669 (E) Page 2 Revision 2.0...
INFORMATION FOR DATA PROGRAMMING CHAPTER 2 INFORMATION FOR DATA PROGRAMMING 1. GENERAL This chapter provides information on the Customer Administration Terminal (CAT) and Maintenance Admin- istration Terminal (MAT) which are used as the man-machine interface with the PBX, and various tables used for indexing the commands by feature.
Page 19
INFORMATION FOR DATA PROGRAMMING & – ← – – ← Figure 2-1 CAT Key Assignment for ETJ-16DD-1 CHAPTER 2 ND-45669 (E) Page 4 Revision 2.0...
INFORMATION FOR DATA PROGRAMMING Table 2-1 Function Keys FUNCTION KEY MEANING Command entry start Execution of data write Cancel of key operation (Clear entry) Display of next data (Step forward) Separator; to be entered between two different data such as first/second data of CM72/74/ 90/97.
INFORMATION FOR DATA PROGRAMMING 2.2 CAT Operation When setting the office data, it is necessary to enter the following three kinds of data: • Command Code • First Data • Second Data An explanation of the data entry procedure follows: (a) Operation for confirming the existing office data + Command Code + + First Data +...
INFORMATION FOR DATA PROGRAMMING (1) Example: When Station Number 300 is to be assigned to LEN 0000 and Station Number 301 to LEN 0001 by CM10 (Refer to Table 2-3.) Table 2-3 Assignment Operation (DISPLAY) STEP 1 Turn ON power switch. STEP 2 Press COMMAND = _...
Page 24
INFORMATION FOR DATA PROGRAMMING (2) Example of Operating Steps for Correcting the Data Entry • In Step 5 in Table 2-3, when is pressed after entering “0001” by mistake, press . Then the state returns to STEP 4. STEP 1 CM10 has been entered and has been pressed.
INFORMATION FOR DATA PROGRAMMING 2.3 Error Messages When an erroneous operation is performed, or wrong data is entered, an error message is displayed on the LCD. Error messages and their meanings are shown in Table 2-4. Table 2-4 Error Messages ERROR MESSAGE MEANING OF MESSAGE ACTION...
INFORMATION FOR DATA PROGRAMMING 3. COMMAND REFERENCE TABLE 3.1 List of Commands Table 2-5 provides a list of commands. Table 2-5 List of Commands COMMAND REMARKS CODE FUNCTION System Data Memory All Clear System Data Memory Partial Clear Setting of System Clock Log in/Log out of Password Mode Language Indicated on Multiline Terminal LCD Card Assignment...
Page 27
INFORMATION FOR DATA PROGRAMMING Table 2-5 List of Commands (Continued) COMMAND REMARKS CODE FUNCTION Function of RS-232C Interface Circuit System Timer Data System Counter Data/PAD Data/Trunk Restriction Class Conversion External Equipment Starting Condition Purpose of PBR/CFT Determination of Tone/Tone Source Digital Announcement Trunk PN-2DATA Common Route Indial...
Page 28
INFORMATION FOR DATA PROGRAMMING Table 2-5 List of Commands (Continued) COMMAND REMARKS CODE FUNCTION Multiline Terminal/SN610 ATTCON/Add-On Module Key Assignment Prime Line Multiline Terminal One-Touch Memory DSS Console Number DSS Console Key Assignment Add-On Module Number Multiline Terminal Soft Key Assignment Type of Data Adapter Data Terminal Attribute Data Nailed Down Connection...
INFORMATION FOR DATA PROGRAMMING 3.2 Quick Reference Table of Commands Required for Service Feature This section provides a quick reference table of various commands related to each service feature. The features are listed alphabetically in the left column. Associated features (shown with bullets) are listed be- low the main features.
INFORMATION FOR DATA PROGRAMMING Table 2-6 List of Commands for Each Business Feature : First Data For Business System : Second Data — : No Data COMMAND 1ST DATA/2ND DATA FEATURE REMARKS (F/S) CODE Y-YYY Account Code – 362/S 0 – 3 F/085 –...
Page 31
INFORMATION FOR DATA PROGRAMMING Table 2-6 List of Commands for Each Business Feature (Continued) : First Data For Business System : Second Data — : No Data COMMAND 1ST DATA/2ND DATA FEATURE REMARKS (F/S) CODE Y-YYY Announcement Service – 124/S –...
Page 32
INFORMATION FOR DATA PROGRAMMING Table 2-6 List of Commands for Each Business Feature (Continued) : First Data For Business System : Second Data — : No Data COMMAND 1ST DATA/2ND DATA FEATURE REMARKS (F/S) CODE Y-YYY Attendant Console – (SN716 DESK CON) 02, 03 F/14 00, 01, 15...
Page 33
INFORMATION FOR DATA PROGRAMMING Table 2-6 List of Commands for Each Business Feature (Continued) : First Data For Business System : Second Data — : No Data COMMAND 1ST DATA/2ND DATA FEATURE REMARKS (F/S) CODE Y-YYY • Attendant Loop Release –...
Page 34
INFORMATION FOR DATA PROGRAMMING Table 2-6 List of Commands for Each Business Feature (Continued) : First Data For Business System : Second Data — : No Data COMMAND 1ST DATA/2ND DATA FEATURE REMARKS (F/S) CODE Y-YYY • Monitor – – 0 –...
Page 35
INFORMATION FOR DATA PROGRAMMING Table 2-6 List of Commands for Each Business Feature (Continued) : First Data For Business System : Second Data — : No Data COMMAND 1ST DATA/2ND DATA FEATURE REMARKS (F/S) CODE Y-YYY Attendant Override – 012, 045, 076/S 0 –...
Page 36
INFORMATION FOR DATA PROGRAMMING Table 2-6 List of Commands for Each Business Feature (Continued) : First Data For Business System : Second Data — : No Data COMMAND 1ST DATA/2ND DATA FEATURE REMARKS (F/S) CODE Y-YYY Automatic Call Distribution (ACD) –...
Page 37
INFORMATION FOR DATA PROGRAMMING Table 2-6 List of Commands for Each Business Feature (Continued) : First Data For Business System : Second Data — : No Data COMMAND 1ST DATA/2ND DATA FEATURE REMARKS (F/S) CODE Y-YYY Automatic Number Identification – –...
Page 38
INFORMATION FOR DATA PROGRAMMING Table 2-6 List of Commands for Each Business Feature (Continued) : First Data For Business System : Second Data — : No Data COMMAND 1ST DATA/2ND DATA FEATURE REMARKS (F/S) CODE Y-YYY Call Back – 156/0 03, 46 0 - 3 F/002 –...
Page 39
INFORMATION FOR DATA PROGRAMMING Table 2-6 List of Commands for Each Business Feature (Continued) : First Data For Business System : Second Data — : No Data COMMAND 1ST DATA/2ND DATA FEATURE REMARKS (F/S) CODE Y-YYY • Call Forwarding - All Calls –...
Page 40
INFORMATION FOR DATA PROGRAMMING Table 2-6 List of Commands for Each Business Feature (Continued) : First Data For Business System : Second Data — : No Data COMMAND 1ST DATA/2ND DATA FEATURE REMARKS (F/S) CODE Y-YYY • Call Forwarding - No Answer –...
Page 41
INFORMATION FOR DATA PROGRAMMING Table 2-6 List of Commands for Each Business Feature (Continued) : First Data For Business System : Second Data — : No Data COMMAND 1ST DATA/2ND DATA FEATURE REMARKS (F/S) CODE Y-YYY • Split Call Forwarding - All Calls –...
Page 42
INFORMATION FOR DATA PROGRAMMING Table 2-6 List of Commands for Each Business Feature (Continued) : First Data For Business System : Second Data — : No Data COMMAND 1ST DATA/2ND DATA FEATURE REMARKS (F/S) CODE Y-YYY • Split Call Forwarding - –...
Page 43
INFORMATION FOR DATA PROGRAMMING Table 2-6 List of Commands for Each Business Feature (Continued) : First Data For Business System : Second Data — : No Data COMMAND 1ST DATA/2ND DATA FEATURE REMARKS (F/S) CODE Y-YYY Call Pickup – – –...
Page 44
INFORMATION FOR DATA PROGRAMMING Table 2-6 List of Commands for Each Business Feature (Continued) : First Data For Business System : Second Data — : No Data COMMAND 1ST DATA/2ND DATA FEATURE REMARKS (F/S) CODE Y-YYY Centrex Compatibility 0 – 3 F/A58 16, 86 –...
Page 45
INFORMATION FOR DATA PROGRAMMING Table 2-6 List of Commands for Each Business Feature (Continued) : First Data For Business System : Second Data — : No Data COMMAND 1ST DATA/2ND DATA FEATURE REMARKS (F/S) CODE Y-YYY Consecutive Speed Dialing – F/19 –...
Page 46
INFORMATION FOR DATA PROGRAMMING Table 2-6 List of Commands for Each Business Feature (Continued) : First Data For Business System : Second Data — : No Data COMMAND 1ST DATA/2ND DATA FEATURE REMARKS (F/S) CODE Y-YYY Dial Conversion – 050, 051/0 –...
Page 47
INFORMATION FOR DATA PROGRAMMING Table 2-6 List of Commands for Each Business Feature (Continued) : First Data For Business System : Second Data — : No Data COMMAND 1ST DATA/2ND DATA FEATURE REMARKS (F/S) CODE Y-YYY Direct Inward System Access –...
Page 48
INFORMATION FOR DATA PROGRAMMING Table 2-6 List of Commands for Each Business Feature (Continued) : First Data For Business System : Second Data — : No Data COMMAND 1ST DATA/2ND DATA FEATURE REMARKS (F/S) CODE Y-YYY Direct Station Selection/Busy Lamp –...
Page 49
INFORMATION FOR DATA PROGRAMMING Table 2-6 List of Commands for Each Business Feature (Continued) : First Data For Business System : Second Data — : No Data COMMAND 1ST DATA/2ND DATA FEATURE REMARKS (F/S) CODE Y-YYY Elapsed Call Timer – –...
Page 50
INFORMATION FOR DATA PROGRAMMING Table 2-6 List of Commands for Each Business Feature (Continued) : First Data For Business System : Second Data — : No Data COMMAND 1ST DATA/2ND DATA FEATURE REMARKS (F/S) CODE Y-YYY External Paging with Meet-Me –...
Page 51
INFORMATION FOR DATA PROGRAMMING Table 2-6 List of Commands for Each Business Feature (Continued) : First Data For Business System : Second Data — : No Data COMMAND 1ST DATA/2ND DATA FEATURE REMARKS (F/S) CODE Y-YYY Flexible Ringing Assignment – 390/1 02, 07 68, 83, 84...
Page 52
INFORMATION FOR DATA PROGRAMMING Table 2-6 List of Commands for Each Business Feature (Continued) : First Data For Business System : Second Data — : No Data COMMAND 1ST DATA/2ND DATA FEATURE REMARKS (F/S) CODE Y-YYY Hotline – 057/S – F/04 00 - 99 –...
Page 53
INFORMATION FOR DATA PROGRAMMING Table 2-6 List of Commands for Each Business Feature (Continued) : First Data For Business System : Second Data — : No Data COMMAND 1ST DATA/2ND DATA FEATURE REMARKS (F/S) CODE Y-YYY • Automatic Intercom – 237/S –...
Page 54
INFORMATION FOR DATA PROGRAMMING Table 2-6 List of Commands for Each Business Feature (Continued) : First Data For Business System : Second Data — : No Data COMMAND 1ST DATA/2ND DATA FEATURE REMARKS (F/S) CODE Y-YYY Least Cost Routing 3/6 Digit 0 - 3 F/A26 - A28 51 - 55...
Page 55
INFORMATION FOR DATA PROGRAMMING Table 2-6 List of Commands for Each Business Feature (Continued) : First Data For Business System : Second Data — : No Data COMMAND 1ST DATA/2ND DATA FEATURE REMARKS (F/S) CODE Y-YYY Message Reminder – 050, 051, 069, 148, 156, 208, 234 - 236, 280 - 294/S 47, 48...
Page 56
INFORMATION FOR DATA PROGRAMMING Table 2-6 List of Commands for Each Business Feature (Continued) : First Data For Business System : Second Data — : No Data COMMAND 1ST DATA/2ND DATA FEATURE REMARKS (F/S) CODE Y-YYY • Wide Area Telephone Service F/02 (WATS) Access Multiline Terminal Attendant...
Page 57
INFORMATION FOR DATA PROGRAMMING Table 2-6 List of Commands for Each Business Feature (Continued) : First Data For Business System : Second Data — : No Data COMMAND 1ST DATA/2ND DATA FEATURE REMARKS (F/S) CODE Y-YYY • Day/Night Mode Change by 0 –...
Page 58
INFORMATION FOR DATA PROGRAMMING Table 2-6 List of Commands for Each Business Feature (Continued) : First Data For Business System : Second Data — : No Data COMMAND 1ST DATA/2ND DATA FEATURE REMARKS (F/S) CODE Y-YYY Off-Premises Extension Pad Lock –...
Page 59
INFORMATION FOR DATA PROGRAMMING Table 2-6 List of Commands for Each Business Feature (Continued) F: First Data For Business System S: Second Data —: No Data COMMAND 1ST DATA/2ND DATA FEATURE REMARKS (F/S) CODE Y-YYY Privacy/Privacy Release Private Line – 08/S Proprietary Multiline Terminal –...
Page 60
INFORMATION FOR DATA PROGRAMMING Table 2-6 List of Commands for Each Business Feature (Continued) F: First Data For Business System S: Second Data —: No Data COMMAND 1ST DATA/2ND DATA FEATURE REMARKS (F/S) CODE Y-YYY • Recall Key 16, 86 17/S F/F1009 •...
Page 61
This page is for your notes. CHAPTER 2 ND-45669 (E) Page 44-2 Addendum-001 Revision 2.1 AUGUST, 1998...
Page 62
INFORMATION FOR DATA PROGRAMMING Table 2-6 List of Commands for Each Business Feature (Continued) : First Data For Business System : Second Data — : No Data COMMAND 1ST DATA/2ND DATA FEATURE REMARKS (F/S) CODE Y-YYY • Ring Frequency Control –...
Page 63
INFORMATION FOR DATA PROGRAMMING Table 2-6 List of Commands for Each Business Feature (Continued) : First Data For Business System : Second Data — : No Data COMMAND 1ST DATA/2ND DATA FEATURE REMARKS (F/S) CODE Y-YYY Software Line Appearance – 01 –...
Page 64
INFORMATION FOR DATA PROGRAMMING Table 2-6 List of Commands for Each Business Feature (Continued) : First Data For Business System : Second Data — : No Data COMMAND 1ST DATA/2ND DATA FEATURE REMARKS (F/S) CODE Y-YYY Step Call – 069, 163/1, 208/0 Supervisory Control of Peripheral Equipment 08/S...
Page 65
INFORMATION FOR DATA PROGRAMMING Table 2-6 List of Commands for Each Business Feature (Continued) : First Data For Business System : Second Data — : No Data COMMAND 1ST DATA/2ND DATA FEATURE REMARKS (F/S) CODE Y-YYY Timed Reminder – 228/S –...
Page 66
INFORMATION FOR DATA PROGRAMMING Table 2-6 List of Commands for Each Business Feature (Continued) : First Data For Business System : Second Data — : No Data COMMAND 1ST DATA/2ND DATA FEATURE REMARKS (F/S) CODE Y-YYY Uniform Call Distribution (UCD) –...
Page 67
INFORMATION FOR DATA PROGRAMMING Table 2-6 List of Commands for Each Business Feature (Continued) : First Data For Business System : Second Data — : No Data COMMAND 1ST DATA/2ND DATA FEATURE REMARKS (F/S) CODE Y-YYY Voice Guide 95/S 12, 13, 14/S 00, 13 Voice Mail Integration –...
INFORMATION FOR DATA PROGRAMMING Table 2-7 List of Commands for Each Hotel/Motel Feature : First Data For Hotel/Motel System : Second Data — : No Data COMMAND 1ST DATA/2ND DATA FEATURE REMARKS (F/S) CODE Y-YYY Automatic Wake-Up – 228, 282 – 284, 286, 287/S –...
Page 69
INFORMATION FOR DATA PROGRAMMING Table 2-7 List of Commands for Each Hotel/Motel Feature (Continued) : First Data For Hotel/Motel System : Second Data — : No Data COMMAND 1ST DATA/2ND DATA FEATURE REMARKS (F/S) CODE Y-YYY Do Not Disturb – 240,241/S 0 –...
Page 70
INFORMATION FOR DATA PROGRAMMING Table 2-7 List of Commands for Each Hotel/Motel Feature (Continued) : First Data For Hotel/Motel System : Second Data — : No Data COMMAND 1ST DATA/2ND DATA FEATURE REMARKS (F/S) CODE Y-YYY Maid Status – 281/S 0 –...
Page 71
INFORMATION FOR DATA PROGRAMMING Table 2-7 List of Commands for Each Hotel/Motel Feature (Continued) : First Data For Hotel/Motel System : Second Data — : No Data COMMAND 1ST DATA/2ND DATA FEATURE REMARKS (F/S) CODE Y-YYY Single Digit Dialing 0 – 3 F/808 –...
INFORMATION FOR DATA PROGRAMMING 4. PRECAUTION 4.1 Conditions for Using Commands (1) Some commands require a system initialization (reset) after assignment/change of the office data, and oth- ers cannot be assigned/changed unless the system is in off-line mode (a state in which call processing is at a halt).
INFORMATION FOR DATA PROGRAMMING (2) When deleting data in any command, enter “CCC” as 2nd data. However, data in the following commands cannot be deleted. • Commands where the initial data ( ) is provided but the initial data ( ) is “NONE”.
INFORMATION FOR DATA PROGRAMMING (b) Operation for changing off-line mode to on-line mode: • Set SW1 as shown below. : POSITION TO BE SET For details, refer to the Circuit Card Manual. 4.3 Method for Installing Line/Trunk Cards In the PBX, all line/trunk circuits are provided by installing the cards into a card shelf. The PBX employs a flexible port assignment architecture in which the system allocates a port (Time Slot) to each LEN (Line Equipment Number) according to system data.
INFORMATION FOR DATA PROGRAMMING • Number of ports on each card Each card slot has four (4) LENs. For the relation between Slot Numbers and LENs, refer to the “Port Assignment Table” of the Office Data Programming Manual. Table 2-9 Port Assignment on Each Line/Trunk Card X: Assignment possible –: Assignment not possible LEN TO BE ASSIGNED ON EACH LTXX...
INFORMATION FOR DATA PROGRAMMING 4.4 Password Entry In a system with password service, a maintenance person is required to enter an authorization level num- ber (Password Level) and appropriate password prior to engaging in programming the system data with the MAT/CAT. A maximum of eight (8) Password Levels can be set up. The number of commands that the maintenance person can access is determined by the password level.
Page 77
This page is for your notes. CHAPTER 2 ND-45669 (E) Page 60 Revision 2.0...
DESCRIPTION OF COMMANDS CHAPTER 3 DESCRIPTION OF COMMANDS 1. GENERAL This chapter provides a detailed description for each command. 2. DETAILED DESCRIPTION OF COMMANDS This section describes the methods for programming commands. Information about each command is present- ed in the following order: (1) Function: The function of the command.
[CM00] System Data Memory All Clear CM00 COMMAND CODE TITLE: SYSTEM DATA MEMORY ALL CLEAR FUNCTION: This command confirms that the system data memory (RAM) area can be Written-in /Read-out and also assigns the Initial Data to the RAM area. PRECAUTION: (1) This command can only be used in off-line mode.
[CM01] System Data Memory Partial Clear CM01 COMMAND CODE TITLE: SYSTEM DATA MEMORY PARTIAL CLEAR FUNCTION: This command is used to clear the data associated with the Numbering Plan (CM20-CM29) or Toll Restriction (CM85-CM8A). PRECAUTION: This command can only be used in off-line mode. ASSIGNMENT PROCEDURE: + 01 + Commands to be cleared: 20, 21, 22, 23, 24, 25, 26 and 29 in Data Memory...
[CM02] Setting of System Clock CM02 COMMAND CODE TITLE: SETTING OF SYSTEM CLOCK FUNCTION: This command is used to assign clock data (day, date and time). PRECAUTION: (1) The system clock starts when EXE is depressed. (2) Reenter all the Clock Data if “HARD ERROR” is displayed as a result of this command. (3) This command is included in MAT mode menu “E1”...
[CM03] Log In/Log Out of Password Mode CM03 COMMAND CODE TITLE: LOG IN/LOG OUT OF PASSWORD MODE FUNCTION: This command is used to enter a password which allows authorized personnel to access commands in accordance with preassigned authorization levels. PRECAUTION: None ASSIGNMENT PROCEDURE: To log in the password mode and enter the password...
[CM04] Language Indicated on Multiline Terminal LCD CM04 COMMAND CODE TITLE: INITIAL LANGUAGE INDICATED ON MULTILINE TERMINAL LCD FUNCTION: This command selects the language that displays on the Multiline Terminal LCDs. PRECAUTION: This command requires a system reset after setting the data. ASSIGNMENT PROCEDURE: 2ND DATA 1ST DATA...
[CM05] Card Assignment CM05 COMMAND CODE TITLE: CARD ASSIGNMENT FUNCTION: This command is used to inform the main processor card (CP00 or CP03) of the SENSE switch (sense wheel) setting on each AP circuit card that is installed. PRECAUTION: (1) This command requires a system reset after setting the data. (2) This command is included in MAT mode menu “E2”...
Page 85
CM05 COMMAND CODE TITLE: CARD ASSIGNMENT Note: Set the SENSE switch on the AP circuit card to match an unequipped slot number as shown below. SENSE WHEEL (04 - 15) SWITCH SETTING VALUE CHAPTER 3 ND-45669 (E) Page 68 Addendum-001 Revision 2.1 AUGUST, 1998...
[CM06] Misc. Trunk Number Assignment CM06 COMMAND CODE TITLE: MISC. TRUNK NUMBER ASSIGNMENT FUNCTION: This command assigns Miscellaneous Trunk Numbers to each card. PRECAUTION: This command requires a system reset after setting the data. ASSIGNMENT PROCEDURE: 1ST DATA 2ND DATA + 06YY + (1-4 digits) (2-4 digits)
CM07 COMMAND CODE TITLE: DTI TRUNK/ISDN TRUNK ASSIGNMENT FUNCTION: This command assigns the DTI/ISDN trunks. PRECAUTION: This command requires a system reset after setting the data. ASSIGNMENT PROCEDURE: 1ST DATA 2ND DATA + 07YY + (4 digits) (4 digits) DATA TABLE: 1ST DATA 2ND DATA RELATED...
Page 88
CM07 COMMAND CODE TITLE: DTI TRUNK/ISDN TRUNK ASSIGNMENT 1ST DATA 2ND DATA RELATED COMMAND DATA MEANING DATA MEANING 32XX Virtual Channel No. DXXX Trunk Number (D000 – D255) 32 XX Note: Trunk numbers already assigned by Home-Side Trunk CM10 cannot be Virtual Channel used.
Page 89
This page is for your notes. THIS PAGE INTENTIONALLY LEFT BLANK. CHAPTER 3 ND-45669 (E) Page 70-2 Addendum-002 Revision 2.2 JANUARY, 1999...
[CM08] Basic Service Features CM08 COMMAND CODE TITLE: BASIC SERVICE FEATURES FUNCTION: This command is used to assign basic features on a system-wide basis. PRECAUTION: After setting 1st data 390 and 391, system reset is required. ASSIGNMENT PROCEDURE: BASIC SERVICE DATA (0/1) + 08 + FEATURE...
Page 91
CM08 COMMAND CODE TITLE: BASIC SERVICE FEATURES DATA TABLE: Initial Data BASIC SERVICE FEATURE SETTING DATA Busy Verification Not available Available Attendant Loop Release Provided Not provided When the system is in night mode, an attendant (dial “0”) call Not transferred from a station is automatically transferred to a specific sta- To transfer tion.
Page 92
CM08 COMMAND CODE TITLE: BASIC SERVICE FEATURES Initial Data BASIC SERVICE FEATURE SETTING DATA Toll Restriction for outgoing call by System Speed Dialing Not provided feature. Provide Warning tone sent to connected parties during Executive Only once Override or Attendant Override. Every 4 sec.
Page 93
CM08 COMMAND CODE TITLE: BASIC SERVICE FEATURES Initial Data BASIC SERVICE FEATURE SETTING DATA This setting determines the trunk seizing sequence when CM Highest available trunk 35 YY = 83 is set to 0. Lowest available trunk Note: When NEAX 2000/1000IVS is installed with loop- start trunks, it is important to select the highest available trunk setting to prevent call collisions.
Page 94
CM08 COMMAND CODE TITLE: BASIC SERVICE FEATURES Initial Data BASIC SERVICE FEATURE SETTING DATA 1000-Slot Memory Block Number “3” for Station Speed Di- Available (See CM20, A50) aling is used as the Memory Block for System Speed Dialing. Not available 1000-Slot Memory Block Number “1”...
Page 95
This page is for your notes. THIS PAGE INTENTIONALLY LEFT BLANK. CHAPTER 3 ND-45669 (E) Page 74-2 Addendum-001 Revision 2.1 AUGUST, 1998...
Page 96
CM08 COMMAND CODE TITLE: BASIC SERVICE FEATURES Initial Data BASIC SERVICE FEATURE SETTING DATA Outgoing C.O. Line Call from a Station to Station connection. Not allowed To allow Answer preference for enhanced Trunk Direct Appearance Display 2-digit trunk ID code (CM30 YY = 19, last two digits assigned) Display 4-digit trunk ID code (CM30 YY = 19)
Page 97
CM08 COMMAND CODE TITLE: BASIC SERVICE FEATURES Initial Data BASIC SERVICE FEATURE SETTING DATA A trunk line placed in Consultation Hold by Call Park-Sys- Not available tem/Tenant, can be retrieved by pressing a trunk line appear- Available ance key on any Multiline Terminal. Periodic Time Indication Tone Sending for C.O.
Page 98
CM08 COMMAND CODE TITLE: BASIC SERVICE FEATURES : Initial Data BASIC SERVICE FEATURE SETTING DATA In delay-type paging, when the paged party encounters a busy To set paging circuit, Call Back is automatically set. (Applicable to Not set both Radio Paging and Speaker Paging.) Restriction of a station to station call between tenants by To cancel CM63 Y=1 is temporarily cancelled by external key.
Page 99
CM07 COMMAND CODE TITLE: DTI TRUNK/ISDN TRUNK ASSIGNMENT 1ST DATA 2ND DATA RELATED COMMAND DATA MEANING DATA MEANING 32XX Virtual Channel No. DXXX Trunk Number (D000 – D255) 32 XX Note: Trunk numbers already assigned by Home-Side Trunk CM10 cannot be Virtual Channel used.
Page 100
This page is for your notes. THIS PAGE INTENTIONALLY LEFT BLANK. CHAPTER 3 ND-45669 (E) Page 70-2 Addendum-002 Revision 2.2 JANUARY, 1999...
Page 101
CM08 COMMAND CODE TITLE: BASIC SERVICE FEATURES : Initial Data BASIC SERVICE FEATURE SETTING DATA 1000-Slot Memory Block Number “2” for Station Speed Di- Available aling is used as the Memory Block for System Speed Dialing. Not available Last Number Redial feature for DP/DTMF telephone. Available (See CM20 - 069) Not available Last Number Redial/Stack Dial for internal calls...
Page 102
CM08 COMMAND CODE TITLE: BASIC SERVICE FEATURES Initial Data BASIC SERVICE FEATURE SETTING DATA Diversion display by ATTCON. Available Not available LDN Diversion by ATTCON. Available (See CM58) Not available Trunk to Trunk Transfer by an Attendant before answer (on Available the OG trunk).
Page 103
CM08 COMMAND CODE TITLE: BASIC SERVICE FEATURES Initial Data BASIC SERVICE FEATURE SETTING DATA Trunk access from a station in Room Cut-Off Status. Restricted to C.O. only Restricted to all Trunk Routes. Message Waiting lamp of calling station is extinguished when Assigned an attendant answers (See CM13-13) Not assigned...
Page 104
CM08 COMMAND CODE TITLE: BASIC SERVICE FEATURES Initial Data BASIC SERVICE FEATURE SETTING DATA Destination of Priority Call 0. Same station as Off-Hook Alarm. (See CM51 YY = 12) Terminate to ATTCON. (See CM46 -54) Destination of Priority Call 1. Same station as Off-Hook Alarm.
Page 105
CM08 COMMAND CODE TITLE: BASIC SERVICE FEATURES Initial Data BASIC SERVICE FEATURE SETTING DATA Call termination to My Line while the extension makes a call Restricted with a secondary extension or trunk line on Multiline Termi- Allowed nal. Note: When 0 (Restricted) is set, 0 (Station Base) should be set by CM08-269.
Page 106
CM08 COMMAND CODE TITLE: BASIC SERVICE FEATURES Initial Data BASIC SERVICE FEATURE SETTING DATA Display last calling station number. 6 seconds Note: This is only applicable for an ETJ-16DC-1, an ETJ- Until next call 16DD-1 or an ETJ-24DS-1. On a Tie Line outgoing call with answer signal, transferring/ Not available holding the call before distant called station answers.
Page 107
CM08 COMMAND CODE TITLE: BASIC SERVICE FEATURES Initial Data BASIC SERVICE FEATURE SETTING DATA Confirmation tone after dialing the access code for Account No tone Code/Authorization Code/Forced Account Code. Service Set Tone (SST) For the Automated Attendant call, caller dials while sending Not allowed (Allowed after sending message or music.
Page 108
CM08 COMMAND CODE TITLE: BASIC SERVICE FEATURES Initial Data BASIC SERVICE FEATURE SETTING DATA Centralized Billing-CCIS feature for local office To provide (for local office) Not provided (for centralized office, INITIAL MP Reset) Maximum number of dialed digits sent to CCIS network 24 digits (Tandem calls over 16 digits and name display) 16 digits...
Page 109
CM08 COMMAND CODE TITLE: BASIC SERVICE FEATURES Initial Data BASIC SERVICE FEATURE SETTING DATA Consecutive Speed Dialing when making an ISDN call. Available Not available Method of charging a transferred call (for use with CP03 Charging to the transferring station or (MP) only) the transfer destination station.
Page 110
CM08 COMMAND CODE TITLE: BASIC SERVICE FEATURES Initial Data BASIC SERVICE FEATURE SETTING DATA Forced release when a called ISDN Terminal is no answer Not available during 3 minutes Available Assignment of the calling party number which is sent to an Calling Party No.
Page 111
CM08 COMMAND CODE TITLE: BASIC SERVICE FEATURES Initial Data BASIC SERVICE FEATURE SETTING DATA Sending ANI/Caller ID/CPN to the OAI terminal. Available Not available Sending ANI/Caller ID/CPN to the SMDR terminal. Available Not available OAI–TSAPI Same as NEAX2400 (recommended setting) SCF1 facility SMFN Off-Hook indication sent Requiring ANI Signal/Caller ID from network when an in-...
[CM09] Additional Service Features CM09 COMMAND CODE TITLE: INITIAL ADDITIONAL SERVICE FEATURES FUNCTION: This command is used to assign additional features on a system-wide basis. PRECAUTION: None ASSIGNMENT PROCEDURE: ADDITIONAL SERVICE DATA (0/1) ST + 09 + DE + + DE + + EXE FEATURE (2 digits)
[CM10] Station Number, Trunk Number, Card Number CM10 COMMAND CODE TITLE: STATION NUMBER, TRUNK NUMBER, CARD NUMBER FUNCTION: This command is used to assign Station Numbers, Trunk Numbers, and Card Numbers to LENs (Line Equipment Numbers). PRECAUTION: (1) When deleting a Station Number (Single Line or Multiline Terminal), be sure to delete Call Pickup data (CM 16), UCD Group data (CM17) and Station Hunting Group data (CM18) in advance.
Page 114
CM10 COMMAND CODE TITLE: STATION NUMBER, TRUNK NUMBER, CARD NUMBER DATA TABLE: SETTING DATA (STATION NUMBER, TRUNK NUMBER, CARD NUMBER) RELATED COMMAND DATA MEANING OF DATA 0000 Single Line Station Number (1-4 digits) x=0-9, A (*), B (#) Note: When assigning a 5-digits station, assign the last four digits in 0511 xxxx CM10.
Page 115
CM10 COMMAND CODE TITLE: STATION NUMBER, TRUNK NUMBER, CARD NUMBER SETTING DATA (STATION NUMBER, TRUNK NUMBER, CARD NUMBER) RELATED COMMAND DATA MEANING OF DATA 0124 E200 Circuit Number of DTMF Receiver (PN-CP03) INITIAL E203 0000 E600 TAS Equipment Interface activated by Station Ringer. CM30 (Use of LC card) YY = 13, 14, 17...
Page 116
CM10 COMMAND CODE TITLE: STATION NUMBER, TRUNK NUMBER, CARD NUMBER SETTING DATA (STATION NUMBER, TRUNK NUMBER, CARD NUMBER) RELATED COMMAND DATA MEANING OF DATA 0000 ISDN Circuit Station Number <X-XXXX> represents ISDN Circuit Station Number INITIAL EFXXXX X : 0-9, A(*), B(#) 0511 ND-45669 (E) CHAPTER 3...
Page 117
CM10 COMMAND CODE TITLE: STATION NUMBER, TRUNK NUMBER, CARD NUMBER • The relation between the locations of the card and the LENs (0000–0511) is shown below. 0195 0199 0203 0207 0211 0215 0219 0223 0227 0231 0235 0239 0243 0247 0251 0255 0194...
[CM11] Virtual-Line Number CM11 COMMAND CODE TITLE: VIRTUAL-LINE NUMBER FUNCTION: This command is used to assign station numbers, Intercom numbers, Loop Line numbers and ICI/OPR Line numbers (for a Multiline Terminal Attendant Position), to Virtual-Lines assigned on a Multiline Terminal. PRECAUTION: (1) The Virtual-Line station numbers must be different from station numbers assigned by CM10.
Page 120
CM11 COMMAND CODE TITLE: VIRTUAL-LINE NUMBER VIRTUAL RELATED VIRTUAL-LINE NUMBER COMMAND Note 0000 A200 Manual Intercom Number (Refer to CM12 YY = 03 CM56 YY = 11 0255 A700 CM90 Manual Intercom Group No. A201 (00-24) A701 Sequential Number in Group (2-7) A224 A724 Note...
Page 121
CM11 COMMAND CODE TITLE: VIRTUAL-LINE NUMBER Note 1: Automatic Intercom Numbers are assigned as shown below: AUTOMATIC AUTOMATIC AUTOMATIC INTERCOM INTERCOM INTERCOM GROUP No.(A) No.(B) A000 A100 A001 A101 A031 A131 Note 2: Manual Intercom Numbers are assigned as shown below: MANUAL INTERCOM GROUP...
[CM12] Station Class-1 CM12 COMMAND CODE TITLE: STATION CLASS-1 FUNCTION: The features for each station are determined by assigning Station Class-1 to each station number. PRECAUTION: (1) When assigning Station Class-1 to Multiline Terminal using this command, enter “X-XXXX (Pri- mary Extension Number)”...
Page 123
CM12 COMMAND CODE TITLE: STATION CLASS-1 ASSIGNMENT PROCEDURE: Automatic/ ICI/OPR DATA Loop STATION Manual/ + DE + + EXE Line No. Line No. (1-4 digits) ST + 12YY + DE + Dial Intercom (4 digits) (4 digits) (1-4 digits) No. (4 digits) DATA TABLE: Initial Data SETTING DATA...
Page 124
CM12 COMMAND CODE TITLE: STATION CLASS-1 : Initial Data SETTING DATA MEANING DATA MEANING Kind of Telephone House Phone 0 (TEL) House Phone 1 (See CM51 YY=14) House Phone 2 House Phone 3 FAX Call Station Group No. 0 FAX Call Station Group No. 1 Note 1 FAX Call Station Group No.
Page 125
CM12 COMMAND CODE TITLE: STATION CLASS-1 : Initial Data SETTING DATA MEANING DATA MEANING Trunk to be seized as a D000 Trunk Number (PVTRK) Private Line on a per sta- tion basis D255 Related Commands: CM35 YY=98, CM42-08 Combination of the main Main Station Number/Sub Station Number Note 5, Note 6 station and sub station...
Page 126
CM12 COMMAND CODE TITLE: STATION CLASS-1 1st LEN 2nd through 4th LEN X: Available (Level 0) Note 1 (Level 1-3) Note 2 –: Not available Series E (Series E mode)/Series III/E-Pro Series E (Series E mode)/Series III/E-Pro Series E (Series E mode/Series III mode) ATTCON/DSS Console ATTCON/DSS Console Series E (Series E mode)/Series III/ E-Pro/...
[CM13] Station Class-2 CM13 COMMAND CODE TITLE: STATION CLASS-2 FUNCTION: The features for each station are to be designated by assigning Station Class-2 for each station number. PRECAUTION: (1) When assigning Station Class-2 to a Multiline Terminal by this command, enter “X-XXXX (Pri- mary Extension Number)”...
Page 128
CM13 COMMAND CODE TITLE: STATION CLASS-2 ASSIGNMENT PROCEDURE: STATION DATA ST + 13YY + DE + DE + + EXE NUMBER (1 digit) (1-4 digits) DATA TABLE: : Initial Data SETTING DATA MEANING DATA MEANING Do Not Disturb-System To provide (DNDS) Not provided Room Cut Off-System...
Page 129
CM13 COMMAND CODE TITLE: STATION CLASS-2 : Initial Data SETTING DATA Ordinary Station or Front Station Message Waiting Front Desk Instrument (FRONT) Ordinary Station Note: MW Lamp of calling station is turned off when Message Wait- ing Front Desk Terminal an- swers (see CM08-233).
[CM15] Service Restriction Class CM15 COMMAND CODE TITLE: SERVICE RESTRICTION CLASS FUNCTION: The restriction of each feature is to be set for each service restriction class assigned to the stations. There are three kinds of Service Restriction Class: A, B and C. The service features to be restricted by these Service Restriction Classes are different.
Page 131
CM15 COMMAND CODE TITLE: SERVICE RESTRICTION CLASS DATA TABLE: Service Class A : Initial Data YY/YYY SERVICE SETTING DATA REST. MEANING DATA MEANING CLASS (A) Call Forwarding – All Calls Restricted Allow Call Hold Trunk Queueing – Outgoing Call Back Guest Name Display via PMS Allow Restricted...
Page 132
CM15 COMMAND CODE TITLE: SERVICE RESTRICTION CLASS Service Class A : Initial Data YY/YYY SERVICE SETTING DATA REST. MEANING DATA MEANING CLASS (A) Message Waiting Lamp set/reset from the sta- Restricted tion Allow Timed Queue Call Forwarding – All Calls – Outside Call Forwarding –...
Page 133
CM15 COMMAND CODE TITLE: SERVICE RESTRICTION CLASS Service Class A : Initial Data YY/YYY SERVICE SETTING DATA REST. MEANING DATA MEANING CLASS (A) Camp-On by Station (Call Waiting Method) Restricted (Answer - Called Side) Allow Call Back - Multiple Assignment Message Reminder (Setting Side) Message Reminder (Set Side) Internal Zone Paging Access/All Zone Internal...
Page 134
CM15 COMMAND CODE TITLE: SERVICE RESTRICTION CLASS Service Class A : Initial Data YY/YYY SERVICE SETTING DATA REST. MEANING DATA MEANING CLASS (A) PS Call Forwarding-Not Available Allow Restricted Voice Guide (Validity of data set by CM48 Y=2 Restricted first data 12, 13, 14.) Allow Roaming Service Allow...
Page 135
This page is for your notes. THIS PAGE INTENTIONALLY LEFT BLANK. CHAPTER 3 ND-45669 (E) Page 110-2 Addendum-001 Revision 2.1 AUGUST, 1998...
Page 136
CM15 COMMAND CODE TITLE: SERVICE RESTRICTION CLASS Service Class B : Initial Data YY/YYY SERVICE SETTING DATA REST. MEANING DATA MEANING CLASS (B) TAS Service Restricted Allow Individual Trunk Access from station Change of mode for CAT Starting up MSF from PB telephone/Multiline Terminal by using an access code Day/Night Mode Change by Station Dialing Periodic Time Indication Tone Sending...
Page 137
CM15 COMMAND CODE TITLE: SERVICE RESTRICTION CLASS Service Class C : Initial Data YY/YYY SERVICE SETTING DATA REST. MEANING DATA MEANING CLASS (C) Immediate Ringing on Single Line Station Restricted Allow One hit ringing for Call Forwarding-All Calls Restricted Allow Ringing Line Pick-up Allow Restricted...
Page 138
CM15 COMMAND CODE TITLE: SERVICE RESTRICTION CLASS Note 1: The tone indication pattern is assigned by the combination of data in YY=83 and YY = 84 : Initial Data MEANING OF DATA Setting Data 600 + 700 [Hz] Modulating Signal 1024 + 1285 [Hz]/16 [Hz] Modulating Signal 480 + 606 [Hz]/8 [Hz]...
[CM16] Call Pickup Group/Group Diversion Group CM16 COMMAND CODE TITLE: CALL PICKUP GROUP/GROUP DIVERSION GROUP FUNCTION: This command is used to assign stations to a Call Pickup Group and a Group Diversion Group. PRECAUTION: (1) The maximum number of stations which can be assigned to a Call Pickup Group is 60. (2) There is no limitation to the number of Call Pickup Groups.
Page 140
CM16 COMMAND CODE TITLE: CALL PICKUP GROUP/GROUP DIVERSION GROUP DATA TABLE: STATION NUMBER (A) SETTING DATA MEANING DATA MEANING DATA MEANING Assignment of Station Station Numbers (A) Station Number (B) Numbers to be included in a Call Pickup Group XXXX XXXX When assigning station numbers to a Call Pickup Group, only two station numbers can be assigned per operation.
[CM17] UCD Group CM17 COMMAND CODE TITLE: UCD GROUP FUNCTION: This command is used to define ACD (Automatic Call Distribution) / UCD (Uniform Call Distribution) groups. PRECAUTION: (1) A maximum of 16 ACD / UCD groups can be assigned per system. (2) A maximum of 60 stations can be assigned to an ACD / UCD group.
Page 142
CM17 COMMAND CODE TITLE: UCD GROUP Initial Data STATION NUMBER (A) SETTING DATA RELATED COMMAND MEANING DATA MEANING DATA MEANING Assignment of the Pi- Station Number to be Member Station (Pilot lot Station in the assigned as Pilot Pilot Station ACD/UCD Group XXXX No.)
[CM18] Station Hunting Group CM18 COMMAND CODE TITLE: STATION HUNTING GROUP FUNCTION: This command is used to assign stations to a Station Hunting Group. There are three hunt types: Pilot System, Circular System and Switch Back System. PRECAUTION: (1) When a Station Hunting Group requires a secretary station, it is necessary to assign Y=2. (2) The maximum number of stations which can be assigned to a Station Hunting Group is 60.
Page 144
CM18 COMMAND CODE TITLE: STATION HUNTING GROUP DATA TABLE: Pilot System Initial Data STATION NUMBER (A) SETTING DATA MEANING DATA MEANING DATA MEANING Setting of Station num- Station Number (A)/ Station Number (B)/ bers included in a Station Data Station Number (A) Data Station Number (B) Hunting Group XXXX...
Page 145
CM18 COMMAND CODE TITLE: STATION HUNTING GROUP Initial Data STATION NUMBER (A) SETTING DATA MEANING DATA MEANING DATA MEANING Secretary Station: Secretary Station Number Secretary Station Serial If an incoming call ter- Numbers: minated to a Station XXXX Serial Numbers to be as- Hunting Group has en- signed to Secretary Station countered all lines busy,...
Page 146
CM18 COMMAND CODE TITLE: STATION HUNTING GROUP (2) Circular System Initial Data STATION NUMBER (A) SETTING DATA MEANING DATA MEANING DATA MEANING Setting of Station Station Number (A)/ Station Number (B)/ Numbers included in a Data Station Number (A) Data Station Number (B) Station Hunting Group XXXX XXXX...
Page 147
CM18 COMMAND CODE TITLE: STATION HUNTING GROUP (3) Switch Back System Initial Data STATION NUMBER (A) SETTING DATA MEANING DATA MEANING DATA MEANING Setting of Station Num- Station Number (A) / Station Number (B) / bers included in a Station Data Station Number (A) Data Station Number (B) Hunting Group...
Page 148
CM18 COMMAND CODE TITLE: STATION HUNTING GROUP Initial Data STATION NUMBER (A) SETTING DATA MEANING DATA MEANING DATA MEANING Secretary Station: Secretary Station Number Secretary Station Serial Same as Pilot System Number: XXXX Example: (Same as Pilot System) Data can be set to all stations belonging to the Switch Back Secretary System.
[CM19] Secretary/Group Diversion Station Number CM19 COMMAND CODE TITLE: SECRETARY/GROUP DIVERSION STATION NUMBER FUNCTION: Station numbers corresponding to Secretary Station Serial Numbers are to be assigned. The assigned numbers are called Secretary Station Numbers. Also, Station numbers are to be assigned as destination stations for Group Diversion.
[CM1A] Data Station Number CM1A COMMAND CODE TITLE: INITIAL DATA STATION NUMBER FUNCTION: This command is used to assign the Data Station Numbers for accommodating the data terminals via the Multiline Terminal. PRECAUTION: (1) This command requires a system reset after setting the data. (2) This command is included in MAT mode menu “A1”...
[CM1B] ISDN Terminal Multipoints Station Number Assignment CM1B COMMAND CODE TITLE: ISDN TERMINAL MULTIPOINTS STATION NUMBER ASSIGNMENT FUNCTION: This command is used for an ISDN Terminal Multipoints Station Number. PRECAUTION: None ASSIGNMENT PROCEDURE: ISDN ISDN CIRCUIT DATA MULTIPOINTS No. + EXE + 1B + STATION No.
[CM1C] PS Station Number Assignment CM1C COMMAND CODE TITLE: PS STATION NUMBER ASSIGNMENT FUNCTION: This command is used to assign the PS Station Numbers for providing the Wireless Communication System. PRECAUTION: None ASSIGNMENT PROCEDURE: ST + 1C + DE + VIRTUAL PS No. PS STATION No.
[CM1D] PS-ID Assignment/PS Operation Data Download CM1D COMMAND CODE TITLE: PS-ID ASSIGNMENT/PS OPERATION DATA DOWNLOAD FUNCTION: This command is used to assign the PS-ID and to download the PS Operation data. PRECAUTION: (1) When a PS is set up initially, set the PS in Data Download Mode by applying power to the PS while pressing the SEND key, and then execute the CM1DYY=20 in Calling Area No.
Page 154
[CM20] Numbering Plan CM20 COMMAND CODE TITLE: NUMBERING PLAN FUNCTION: Trunk routes and features are assigned access codes. Required developments (Route Advance, Tenant, Kind of Calling Terminal and Closed Number data) and trunk routes or features are assigned access codes with CM22, CM23, CM24 and CM26. The following figure shows the relationship between com- mands: For each access code Numbering Plan...
Page 155
[CM##] Title - After typing title, apply default character tag and then TOC paragraph tag. CM20 COMMAND CODE TITLE: NUMBERING PLAN ASSIGNMENT PROCEDURE: DATA ACCESS CODE ST + 20Y + DE + + DE + + EXE (3 digits) (1-3 digits) DATA TABLE: RELATED ACCESS CODE...
CM20 COMMAND CODE TITLE: [CM20] Numbering Plan NUMBERING PLAN ASSIGNMENT DATA RELATED REMARKS COMMAND DATA MEANING Call Park-System (Set) For Single Line Station/ CM15 YY = 96 (PRKS) Multiline Terminal/ ATTCON Call Park-System (Retrieve) (PRKR) Call Forwarding-All Calls (Entry) CM15 YY = 00, 26 (FDAE) Call Forwarding-All Calls (Cancel) (FDAC)
Page 157
CM20 COMMAND CODE TITLE: NUMBERING PLAN ASSIGNMENT DATA RELATED REMARKS COMMAND DATA MEANING Wake-up Call/Timed Reminder (Set) CM15 YY = 13 (WUS) Wake-up Call/Timed Reminder (Cancel) (WUC) Wake-up Call Set from Predetermined Station CM15 YY = 20 (SWU) (Single Wake-up time operation) Wake-up Call Set from Predetermined Station CM15 YY = 21 (MWU)
Page 158
CM20 COMMAND CODE TITLE: [CM20] Numbering Plan NUMBERING PLAN ASSIGNMENT DATA RELATED REMARKS COMMAND DATA MEANING TAS Answer A CM15 YY = 53 (TASA) CM53 TAS Answer B (TASB) TAS Answer C (TASC) TAS Answer D (TASD) TAS Answer E (TASE) Trunk Hold Code Trunk Answer Code...
Page 159
CM20 COMMAND CODE TITLE: NUMBERING PLAN ASSIGNMENT DATA RELATED REMARKS COMMAND DATA MEANING Paging Answer Zone 0 CM30 YY = 28 (PAG0) CM44 CM15 YY = 08 Paging Answer Zone 1 (PAG1) Paging Answer Zone 2 (PAG2) Paging Answer Zone 3 (PAG3) Paging Answer Zone 4 (PAG4)
Page 160
CM20 COMMAND CODE TITLE: [CM20] Numbering Plan NUMBERING PLAN ASSIGNMENT DATA RELATED REMARKS COMMAND DATA MEANING Priority Call 0 These calls are routed to the CM90 (PRI0) operator at the ATTCON CM15 YY = 17, 18 CM08-250, 251 Priority Call 1 (PRI1) Special Operator Call 0 CM90...
Page 161
CM20 COMMAND CODE TITLE: NUMBERING PLAN ASSIGNMENT DATA RELATED REMARKS COMMAND DATA MEANING 2/3 digits-Station CM41 Y = 0 (2/3) F = 13 2/4 digits-Station (2/4) 3/4 digits-Station (3/4) 2/3/4 digits-Station (2/3/4) Digital Announcement Trunk Access CM10, CM15 (VRCRC) (Record) YY = 33 Digital Announcement Trunk Access (VRCRP)
Page 162
CM20 COMMAND CODE TITLE: [CM20] Numbering Plan NUMBERING PLAN ASSIGNMENT DATA RELATED REMARKS COMMAND DATA MEANING Voice Message Waiting Service-System CM13 YY = 03 (VWST) (Setting of Station Numbers to be sent) CM15 YY = 41, 42 CM49 YY = 00 Voice Message Waiting Service-Individual (VW1ST) (Setting of Station Numbers to be sent)
Page 163
CM20 COMMAND CODE TITLE: NUMBERING PLAN ASSIGNMENT DATA RELATED REMARKS COMMAND DATA MEANING Internal Zone Paging Group 0 CM56 YY = 00 – 07 (IPGC0) CM15 YY = 49 CM90 Internal Zone Paging Group 1 (IPGC1) Internal Zone Paging Group 2 (IPGC2) Internal Zone Paging Group 3 (IPGC3)
Page 164
CM20 COMMAND CODE TITLE: [CM20] Numbering Plan NUMBERING PLAN ASSIGNMENT DATA RELATED REMARKS COMMAND DATA MEANING Message Waiting/Message Reminder (Search) CM15 YY = 47, 48 (MW/RS) CM13 – 03 CM51 YY = 15 Message Waiting/Message Reminder CM90 (MW/RA) (Retrieve) Message Reminder (Set) (MRS) Message Reminder (Cancel) (MRC)
Page 165
CM20 COMMAND CODE TITLE: NUMBERING PLAN ASSIGNMENT DATA RELATED REMARKS COMMAND DATA MEANING Voice Call/Ring Tone programming For Multiline Terminal (V/TON) All Zone Internal Paging For calling CM08 – 158 (AZP) Voice Message Waiting Service-Individual All Clear when the called station is no answer Split Call Forwarding - All Calls (Entry) Split Call Forwarding - All Calls (Cancel) Split Call Forwarding - Busy Line/No Answer...
Page 166
CM20 COMMAND CODE TITLE: NUMBERING PLAN ASSIGNMENT DATA RELATED REMARKS COMMAND DATA MEANING Trunk Route Data assignment for Trunk CM30 (RT00) Routes that correspond to access codes for outgoing Trunk Route trunk calls (COT, ODT, etc.) Trunk Route Trunk Route (RT63) Route Advance Block 00 Data is to be assigned in the...
Page 167
This page is for your notes. THIS PAGE INTENTIONALLY LEFT BLANK. CHAPTER 3 ND-45669 (E) Page 140-2 Addendum-001 Revision 2.1 AUGUST, 1998...
Page 168
CM20 COMMAND CODE TITLE: [CM20] Numbering Plan NUMBERING PLAN ASSIGNMENT DATA RELATED REMARKS COMMAND DATA MEANING Tenant Block Data is to be assigned when CM23 (TNB00) the purpose and method of the same access code vary Tenant Block with each tenant. Tenant Block Tenant Block (TNB23)
[CM21] Single Digit Access Code CM21 COMMAND CODE TITLE: SINGLE DIGIT ACCESS CODE FUNCTION: This command sets a single-digit code to be recognized under timing start condition. PRECAUTION: None ASSIGNMENT PROCEDURE: ACCESS DATA ST + 21Y + DE + CODE + DE + + EXE (3 digits)
[CM22] Route Advance CM22 COMMAND CODE TITLE: ROUTE ADVANCE FUNCTION: This command is used to assign alternative trunk routes to each Route Advance Block. PRECAUTION: A maximum of seven consecutive priorities can be assigned. ASSIGNMENT PROCEDURE: PRIORITY DATA ORDER ST + 22YY + DE + + DE + + EXE (3 digits)
[CM23] Tenant Development CM23 COMMAND CODE TITLE: TENANT DEVELOPMENT FUNCTION: Trunk routes and features are assigned by developing access codes for each tenant. For tenant assign- ments requiring development of route advance and kind of calling terminal data for each trunk route assignment, each development and the corresponding trunk routes are to be assigned using CM22 and CM24.
[CM24] Kind of Calling Terminal Development CM24 COMMAND CODE TITLE: KIND OF CALLING TERMINAL DEVELOPMENT FUNCTION: For each access code assigned to a calling terminal block, a trunk route can be assigned based on which type of terminal is placing the call. For calling terminal assignments requiring development of route advance and kind of special terminal data for trunk route assignments, each of these developments and the corresponding trunk routes are assigned using CM22 and CM25.
Page 173
[CM25] Kind of Special Terminal Development CM25 COMMAND CODE TITLE: KIND OF SPECIAL TERMINAL DEVELOPMENT FUNCTION: For each access code assigned to a special terminal block, a trunk route can be assigned based on which type of special terminal (ordinary station or analog data station) is placing the call. For special terminal assignments requiring development of route advance data for trunk route assignment, route advance development and the corresponding trunk routes are assigned using CM22.
[CM26] Closed Number Development CM26 COMMAND CODE TITLE: CLOSED NUMBER DEVELOPMENT FUNCTION: For each access code assigned to a closed number block, a trunk route is selected and the system is assigned to a) Repeat the access code as a dialed digit (to the C.O.) b) To add digits to convert the access code into other digits These assignments are completed prior to dialing the rest of the number.
Page 175
CM26 COMMAND CODE TITLE: CLOSED NUMBER DEVELOPMENT DATA TABLE: Initial Data CLOSED NUMBER BLOCK No. SETTING DATA RELATED COMMAND MEANING DATA MEANING Closed Number Block 00 Trunk Route CM30 (RT Data) Closed Number Block 31 Trunk Route Route Advance Block 00 CM22 Route Advance Block 31 Tenant Block...
[CM29] Numbering Plan Tenant Group CM29 COMMAND CODE TITLE: NUMBERING PLAN TENANT GROUP FUNCTION: When each tenant has its own numbering plan in a multiple-tenant system, all the tenants are divided into four groups, each consisting of tenants having identical features in their numbering plans. Numbering Plan Group data is then assigned on a tenant basis.
[CM2A] ID Code Assignment with MP CM2A COMMAND CODE TITLE: ID CODE ASSIGNMENT WITH MP FUNCTION: This command assigns ID codes used for the Authorization Code/Forced Account Code/Direct Inward System Access (DISA) features without using an AP card. PRECAUTION: These ID Codes are available, when CM08-216/217 are assigned to “0”. ASSIGNMENT PROCEDURE: ID CODE DATA...
Page 178
CM2A COMMAND CODE TITLE: ID CODE ASSIGNMENT WITH MP Initial Data SETTING DATA ID CODE NUMBER MEANING DATA MEANING Service Class A/B for XX: 00–99 XXXX Authorization Code/Forced Account Code Service Class B (00–15 Service Class A (00–15 Note Service Class C for Authorization XX: 00–99 Service Feature Class C Code/Forced Account Code...
[CM30] Trunk Data CM30 COMMAND CODE TITLE: TRUNK DATA FUNCTION: This command is used to assign characteristics to trunk lines which have been defined with CM10. PRECAUTION: This command is included in MAT mode menu “B1” (Trunk number data [COM01]). ASSIGNMENT PROCEDURE: TRUNK NUMBER...
Page 180
CM30 COMMAND CODE TITLE: TRUNK DATA Initial Data SETTING DATA RELATED COMMAND MEANING DATA MEANING Terminating System in Day ATTCON+Trunk Line Appearance Mode for incoming C.O. Calls Note 1 (DIC) CM30 YY =17 Note 2 Termination to ATTCON Direct Inward System Access (DISA) ISDN Indial ATTCON+TAS ATTCON+Trunk-Direct...
Page 181
CM30 COMMAND CODE TITLE: TRUNK DATA Initial Data SETTING DATA RELATED COMMAND MEANING DATA MEANING Direct–In Termination in Day Station Number for Direct–In Termi- CM10, 11 Mode nation in Day Mode (DDIT) XXXX Abbreviated Code of System Speed CM71–66 Dialing for DIT–Outside (XX=00–31) CM35 YY=40 EBXXX Digital Announcement Trunk Circuit CM10, CM15...
Page 182
CM30 COMMAND CODE TITLE: TRUNK DATA Initial Data SETTING DATA RELATED COMMAND MEANING DATA MEANING Handling of busy/not available CM44, CM53 Direct–In Termination destina- Forward to TAS BUZZER (DBSY) tion in Day mode. Indication Forward to ATTCON Automatic Camp–On Keep the call ringing (Wait until the station becomes idle) Handling of busy/not available Same as YY = 13...
Page 183
CM30 COMMAND CODE TITLE: TRUNK DATA : Initial Data SETTING DATA RELATED COMMAND MEANING DATA MEANING Paging Answer Zone/Kind of Paging CM20 – 070 Kind of Paging (PAGA) Paging Answer Zone CM20 – 079 CM44 – 02XX Paging Answer Zone 0: Paging Answer Zone 0 9: Paging Answer Zone 9 Kind of Paging...
Page 184
CM30 COMMAND CODE TITLE: TRUNK DATA : Initial Data SETTING DATA RELATED COMMAND MEANING DATA MEANING Handling of busy/not available/ Same as YY=30 CM41 (NRAD) Automated Attendant/ Direct (Y=0 No. 34) Inward System Access (DISA) CM45 in night mode. Note: For DISA, this data is effective only for a station call.
Page 185
This page is for your notes. THIS PAGE INTENTIONALLY LEFT BLANK. CHAPTER 3 ND-45669 (E) Page 156-2 Addendum-002 Revision 2.2 JANUARY, 1999...
Page 186
CM30 COMMAND CODE TITLE: TRUNK DATA Initial Data SETTING DATA RELATED COMMAND MEANING DATA MEANING Handling of timed–out Disconnection (RATO) Automated Attendant Call in Forward to TAS Indicator CM41 Y=0 Day mode. Function No. 43 CM45 Forward to ATTCON CM30 Forward to DIT Station YY=04, 05 DT Connection (Redial)
[CM31] System Attribute Data CM31 COMMAND CODE TITLE: SYSTEM ATTRIBUTE DATA FUNCTION: This command is used to assign the system attribute data. PRECAUTION: None ASSIGNMENT PROCEDURE: 1ST DATA 2ND DATA + 31Y + EXE (1-2 digits) (1-2 digits) DATA TABLE: Initial Data 1ST DATA 2ND DATA...
Page 188
CM31 COMMAND CODE TITLE: SYSTEM ATTRIBUTE DATA Initial Data 1ST DATA 2ND DATA DATA MEANING DATA MEANING AP Number 0 Designation of MF/Caller ID Receiver/911 Sender to each circuit AP Number 3 (No. 0–3) INITIAL DATA RECEIVER Note: AP Number (0 – 3) correspond to the No.
Page 189
CM35 COMMAND CODE TITLE: TRUNK ROUTE DATA FUNCTION: This command assigns trunk route characteristics. A trunk route is a group of trunks with common char- acteristics used for a common purpose. PRECAUTION: (1) The following table shows the value of the Central Office Trunk (COT/DID) PAD or Tie Line Trunk (ODT/DTI) PAD assigned by YY=19, Data 4 –...
CM35 COMMAND CODE TITLE: TRUNK ROUTE DATA (2) When assigning a Tie Line, the data in YY = 09 (Incoming Call Signaling System) should be simi- lar to that of YY = 20 (Sender Starting Condition). The following table shows the assignment of the Sender Starting Condition in relation to the Incoming Call Signaling System.
Page 191
CM35 COMMAND CODE TITLE: TRUNK ROUTE DATA DATA TABLE: Initial Data YY/YYY SETTING DATA RELATED COMMAND MEANING DATA MEANING Kind of Trunk Route DDD (C.O., DID) Trunk/ISDN Trunk (TK) FX Trunk WATS Trunk CCSA Trunk TIE (Tie Line) Trunk Paging Trunk/Interface with BGM Tone Source and Wake-Up Announce Not used Dialing Signal Type...
Page 192
CM35 COMMAND CODE TITLE: TRUNK ROUTE DATA Initial Data YY/YYY SETTING DATA RELATED COMMAND MEANING DATA MEANING Application of answer signal (ANS) from the distant office for out- Battery Reversal (C.O. line) going connection. Answer Signal arrives (Tie line/ISDN) Answer Signal does not arrive (Polarity Reversal is ignored and Answer timing shall be set by CM41 Y=0 Function No.
Page 193
CM35 COMMAND CODE TITLE: TRUNK ROUTE DATA Initial Data YY/YYY SETTING DATA RELATED COMMAND MEANING DATA MEANING Toll Restriction To provide CM81, CM8A (TRP) CM85 CM35 Not to provide YY = 76 Number of digits to be re- 1 digit CM76 (PDG) ceived on DID.
Page 194
CM35 COMMAND CODE TITLE: TRUNK ROUTE DATA Initial Data YY/YYY SETTING DATA RELATED COMMAND MEANING DATA MEANING Kind of Call Termination Indi- C.O. Incoming 0 (Standard “LDN” key) CM90 (ICI) cator Key/Lamp on ATTCON. C.O. Incoming 1 CM50 With respect to incoming calls C.O.
Page 195
CM35 COMMAND CODE TITLE: TRUNK ROUTE DATA Initial Data YY/YYY SETTING DATA RELATED COMMAND MEANING DATA MEANING Sending of Hook Flash to out- Not sending CM90 YY = 00 (SHF) side Sending DATA = F1009 CM41 Y = 2 Function No. = Digit addition and deletion at “0”...
Page 196
CM35 COMMAND CODE TITLE: TRUNK ROUTE DATA Initial Data YY/YYY SETTING DATA RELATED COMMAND MEANING DATA MEANING Sender Prepause Timing 0 sec CM08-193, (PPT) 0.5 sec 194, 331 1.0 sec CM35 YY = 43 1.5 sec 2.0 sec 2.5 sec 4.0 sec 5.0 sec 6.0 sec...
Page 197
CM35 COMMAND CODE TITLE: TRUNK ROUTE DATA Initial Data YY/YYY SETTING DATA RELATED COMMAND MEANING DATA MEANING Trunk Queuing-Outgoing Not allowed CM15 YY = 02 (OGQ) Allowed Distinctive LED indication on Green (LED : 120 IPM) (LEDI) a Multiline Terminal during (LED : 120 IPM) Note 3 external incoming call termi-...
Page 198
CM35 COMMAND CODE TITLE: TRUNK ROUTE DATA Initial Data YY/YYY SETTING DATA RELATED COMMAND MEANING DATA MEANING Trunk Access Code sent to When a trunk is seized by a Trunk (S2DC) SMDR for outgoing call Appearance key or LCR, one or two-digit code (00-99) is sent out to the SMDR.
Page 199
CM35 COMMAND CODE TITLE: TRUNK ROUTE DATA Initial Data YY/YYY SETTING DATA RELATED COMMAND MEANING DATA MEANING Restriction of Outgoing Restricted (ORCF) Connection Allowed Note 6 Restriction of Outgoing Restriction of Outgoing Restricted Note 6 (ORCG) Connection Allowed (Restricted-2) (RCG) Restriction of Outgoing Restricted (ORCH)
Page 200
CM35 COMMAND CODE TITLE: TRUNK ROUTE DATA Initial Data YY/YYY SETTING DATA RELATED COMMAND MEANING DATA MEANING Announcement Service Restricted CM20, (AN0) Group 0 Allowed A03-A09 CM49 Announcement Service Restricted YY = 00 – (AN1) Group 1 Allowed 04XX Announcement Service Restricted CM15 (AN2)
Page 201
[CM35] Trunk Route Data CM35 COMMAND CODE TITLE: TRUNK ROUTE DATA Initial Data YY/YYY SETTING DATA RELATED COMMAND MEANING DATA MEANING Distinctive Ringing by detect- To provide CM30 ing the ringing signal from the Not provided YY = 02, 03 Main PBX (or Centrex).
Page 202
CM35 COMMAND CODE TITLE: TRUNK ROUTE DATA Initial Data YY/YYY SETTING DATA RELATED COMMAND MEANING DATA MEANING Assignment of route-class data in CCIS Route to Route Restriction Night Trunk Restriction class Day Trunk Restriction class Assignment data is the same as CM12 YY=01 Designated seizure of trunks Allow...
Page 203
CM35 COMMAND CODE TITLE: TRUNK ROUTE DATA Initial Data YY/YYY SETTING DATA RELATED COMMAND MEANING DATA MEANING Kind of trunk route for voice Event Based CCIS Route channel and common signal- Other Trunk Route ing channel Sending of received ANI To send information from network to Not sent...
Page 204
[CM35] Trunk Route Data CM35 COMMAND CODE TITLE: TRUNK ROUTE DATA Note 1: In case of CM35 YY = 76, Data = 15, not specified (release the sender by time out or by answer signal from the called distant office). In case of CM35 YY = 76, Data = 00 –...
Page 205
This page is for your notes. THIS PAGE INTENTIONALLY LEFT BLANK. CHAPTER 3 ND-45669 (E) Page 174-2 Addendum-001 Revision 2.1 AUGUST, 1998...
[CM36] Restriction Data for Tandem Connection CM36 COMMAND CODE TITLE: RESTRICTION DATA FOR TANDEM CONNECTION FUNCTION: This command is used to define restriction data for tandem connection within a system, for each combi- nation of an incoming trunk route and an outgoing trunk route. PRECAUTION: Any incoming Trunk Route assigned to “No release signal”...
[CM38] AMP Trunk CM38 COMMAND CODE TITLE: AMP TRUNK FUNCTION: This command is used to define the AMP Trunk controlled data. PRECAUTION: None ASSIGNMENT PROCEDURE: INCOMING/OUTGOING TRUNK ROUTE 38YY or AMP PATTERN NUMBER(4 digits or 2 digits) + DATA (1-2 digits) + DATA TABLE: Initial Data INCOMING/OUTGOING TRUNK...
Page 208
CM38 COMMAND CODE TITLE: AMP TRUNK Initial Data INCOMING/OUTGOING TRUNK SETTING DATA RELATED ROUTE NO. COMMAND DATA MEANING AMP PATTERN NO. AMP Pattern Number 00 Echo Canceller Gain Controller AMP Pattern Number 14 AMP Pattern Number 00 Mode Selection of Tone Disabler G164 AMP Pattern Number 14 G165...
[CM40] Function of RS-232C Interface Circuit CM40 COMMAND CODE TITLE: FUNCTION OF RS-232C INTERFACE CIRCUIT FUNCTION: This command is used to assign the function of the RS-232C interface circuits, mounted on the MP card. The MP card has two RS-232C interface circuits, which are used for the following purposes: (1) PN-CP00/PN-CP00-B PORT LOCATION PURPOSES...
Page 210
CM40 COMMAND CODE TITLE: FUNCTION OF RS-232C INTERFACE CIRCUIT ASSIGNMENT PROCEDURE: PORT LOCATION NUMBER DATA 40YY + DE + (0/1) (1-4 digits) DATA TABLE: (1) Data Assignment for MAT (a) Purpose of RS-232C port Initial Data YY (Note 2) SETTING DATA PORT LOCATION NUMBER MEANING DATA...
Page 211
CM40 COMMAND CODE TITLE: FUNCTION OF RS-232C INTERFACE CIRCUIT Initial Data SETTING DATA PORT LOCATION NUMBER MEANING DATA MEANING Data Speed Port 0 1200 bps Port 1 2400 bps 4800 bps 9600 bps None 1200 bps (c) RS-232C Port Assignment for Data Load/Save/Verify Initial Data SETTING DATA PORT LOCATION NUMBER...
Page 212
CM40 COMMAND CODE TITLE: FUNCTION OF RS-232C INTERFACE CIRCUIT Initial Data SETTING DATA (Note 1, Note 2) PORT LOCATION NUMBER MEANING DATA MEANING Transmission Level of Port 1 –6 dBm built-in MODEM –7 dBm –8 dBm –9 dBm –10 dBm –11 dBm –12 dBm –13 dBm...
Page 213
CM40 COMMAND CODE TITLE: FUNCTION OF RS-232C INTERFACE CIRCUIT Initial Data SETTING DATA PORT LOCATION NUMBER MEANING DATA MEANING DTR signal sent to terminal Port 0 High RTS signal sent to terminal Port 0 High Data Speed Port 0 1200 bps 2400 bps 4800 bps 9600 bps...
[CM41] System Timer Data CM41 COMMAND CODE TITLE: SYSTEM TIMER DATA FUNCTION: This command assigns System Timer data. PRECAUTION: None ASSIGNMENT PROCEDURE: DATA FUNCTION NUMBER + 41Y + (2 digits) (2 digits) DATA TABLE: Note: Initial Data in the Data Table represents the timing for the data “NONE”. TIMER DATA FUNCTION INITIAL...
Page 215
CM41 COMMAND CODE TITLE: SYSTEM TIMER DATA TIMER DATA FUNCTION INITIAL INCREMENT PURPOSE NUMBER DATA UNIT TIME SMDR Valid Call 4 sec. Timer (Pseudo- Answer timer) (sec.) Disconnect 0.96 ... 13 0.48 sec. recognition time ..5.76 6.24 0.48 0.96 1.44 1.92 2.40 for trunks 1.44...
Page 216
CM41 COMMAND CODE TITLE: SYSTEM TIMER DATA TIMER DATA FUNCTION INITIAL INCREMENT PURPOSE NUMBER DATA UNIT TIME DTMF signal 64 ms......50 width of Out (ms.) ..... 3200 Pulse-Long from ATTCON Call Forwarding – 4 sec....29 No Answer for In- ....
Page 217
CM41 COMMAND CODE TITLE: SYSTEM TIMER DATA TIMER DATA FUNCTION INITIAL INCREMENT PURPOSE NUMBER DATA UNIT TIME ........15 Ringing duration 8 sec. of Automatic 40 ........ 120 Wake-Up/Timed Reminder call (sec.) 48 ........ 128 Inter-digit Pause ........14 1 sec. on Outgoing Call (sec.) ........
Page 218
CM41 COMMAND CODE TITLE: SYSTEM TIMER DATA TIMER DATA FUNCTION INITIAL INCREMENT PURPOSE NUMBER DATA UNIT TIME ..............Timing of unan- 4 sec. swered call after ..............forwarding to pre- determined station (sec.) ..............in automated At- tendant/DISA PBX Dial In ORT ............
Page 219
CM41 COMMAND CODE TITLE: SYSTEM TIMER DATA TIMER DATA FUNCTION INITIAL INCREMENT PURPOSE NUMBER DATA UNIT TIME DTMF Inter-Digi- 32 ms. tal Pause for VMS (ms.) (01-02) 80 100 120 160 200 240 16 ms. (03-04) 20 ms. (04-05) 40 ms. (05-08) ............
Page 220
[CM41] System Timer Data CM41 COMMAND CODE TITLE: SYSTEM TIMER DATA TIMER DATA FUNCTION INITIAL INCREMENT PURPOSE NUMBER DATA UNIT TIME ............Time before an- 4 sec. swering by Auto- ............mated Attendant (sec.) ............ND-45669 (E) CHAPTER 3 Addendum-001 Page 188-1 AUGUST, 1998 Revision 2.1...
Page 221
This page is for your notes. THIS PAGE INTENTIONALLY LEFT BLANK. CHAPTER 3 ND-45669 (E) Page 188-2 Addendum-001 Revision 2.1 AUGUST, 1998...
Page 222
CM41 COMMAND CODE TITLE: SYSTEM TIMER DATA TIMER DATA FUNCTION INITIAL INCREMENT PURPOSE NUMBER DATA UNIT TIME ............Status Change 1120 80 ms. Rebound Guard 80 160 ............3200 Timer 1200 (ms.) 80 160 240 ............3280 Path On Delay ............
Page 223
CM41 COMMAND CODE TITLE: SYSTEM TIMER DATA TIMER DATA FUNCTION INITIAL INCREMENT PURPOSE NUMBER DATA UNIT TIME ..............Message duration 4 sec. for Announce- ..............ment Service-PS No Answer/PS (sec.) ..............Busy ............Overlap Sending 1 sec. Mode timer for ............
Page 224
[CM41] System Timer Data CM41 COMMAND CODE TITLE: SYSTEM TIMER DATA TIMER DATA FUNCTION INITIAL INCREMENT PURPOSE NUMBER DATA UNIT TIME ..........Simultaneous 4 sec. Paging Timer (For 392sec. 0sec. 4sec. Group Calling ..........Conference: 6/10 (sec.) 396sec. 4sec. 8sec. party) Off-Hook Detect 03 ............
Page 225
CM41 COMMAND CODE TITLE: SYSTEM TIMER DATA TIMER DATA FUNCTION INITIAL INCREMENT PURPOSE NUMBER DATA UNIT TIME COT Ringing De- 32 ms. tect Timer 160 192 224 256 288 (ms.) 192 224 256 288 320 COT Trunk Re- 03 ..........15 128 ms.
Page 226
[CM41] System Timer Data CM41 COMMAND CODE TITLE: SYSTEM TIMER DATA TIMER DATA FUNCTION INITIAL INCREMENT PURPOSE NUMBER DATA UNIT TIME Loop Momentary 1280 03 ..........99 128 ms. Open Guard Tim- (ms.) 128 256 384 ..........12672 er for COT Loop Start OG Connec- tion Release Detect...
Page 227
CM41 COMMAND CODE TITLE: SYSTEM TIMER DATA TIMER DATA FUNCTION INITIAL INCREMENT PURPOSE NUMBER DATA UNIT TIME 02 ..............Main PBX 1280 128 ms. (Centrex) Ring ..............1792 Distinction Timer 1408 (ms.) 128 256 ..............1920 • When Main PBX (Centrex) sends immediate ringing, this data must be assigned as follows: CM41 Y=2-00 <...
Page 228
CM41 COMMAND CODE TITLE: SYSTEM TIMER DATA TIMER DATA FUNCTION INITIAL INCREMENT PURPOSE NUMBER DATA UNIT TIME ............15 Wink/Delay Sig- 1 sec. nal time out to re- (sec.) ............15 ceive Note 9 Ring Signal De- 03 ............. 15 32 ms.
Page 229
CM41 COMMAND CODE TITLE: SYSTEM TIMER DATA TIMER DATA FUNCTION INITIAL INCREMENT PURPOSE NUMBER DATA UNIT TIME ........... Ground Start 1 sec. (Return Ground) (sec.) ........... Detect Timing for DTI Trunk Note 9 Note 1: When timer data 99 is assigned by the function number 05, the recall is not performed. Note 2: When timer data 99 is assigned by the function number 06, the recall is not performed.
[CM42] System Counter Data/pad Data/trunk Restriction Class Conver- sion CM42 COMMAND CODE TITLE: SYSTEM COUNTER DATA/PAD DATA/TRUNK RESTRICTION CLASS CONVERSION FUNCTION: This command is used to set the System Counter data, the programmable PAD data and the Trunk Restriction Class data to convert the Restriction Class sent to or from the ICS as a Deluxe Traveling Class Mark-CCIS.
Page 231
CM42 COMMAND CODE TITLE: SYSTEM COUNTER DATA/PAD DATA/TRUNK RESTRICTION CLASS CONVERSION DATA TABLE: System Counter Data Note: Initial data in the Data Table represents the value for the data “NONE”. INITIAL KIND OF SYSTEM COUNTER SETTING DATA REMARKS DATA Number of waiting calls which Number of Waiting Calls will cause attendant’s Call Wait- ing LCD to flash.
Page 232
CM42 COMMAND CODE TITLE: SYSTEM COUNTER DATA/PAD DATA/TRUNK RESTRICTION CLASS CONVERSION INITIAL KIND OF SYSTEM COUNTER SETTING DATA REMARKS DATA Number of Call Forwards in Mul- Number of times tiple-Call Forwarding Maximum number of calls in Number of calls in queue queue in each UCD group for con- in each UCD group trolling external equipment inter-...
Page 233
CM42 COMMAND CODE TITLE: SYSTEM COUNTER DATA/PAD DATA/TRUNK RESTRICTION CLASS CONVERSION PAD Data (Programmable) PATTERN PAD DATA PATTERNS CONNECTING PATTERNS CM35 YY=19 CM35 YY=19 CM35 YY=19 CM35 YY=19 (A – B) 2ND DATA=0 2ND DATA=1 2ND DATA=2 2ND DATA=3 1ST DATA STA –...
Page 234
This page is for your notes. THIS PAGE INTENTIONALLY LEFT BLANK. ND-45669 (E) CHAPTER 3 Addendum-001 Page 199-2 AUGUST, 1998 Revision 2.1...
Page 235
CM42 COMMAND CODE TITLE: SYSTEM COUNTER DATA/PAD DATA/TRUNK RESTRICTION CLASS CONVERSION T/R: Transmit/Receive +: Gain -: Loss PAD DATA OF B TRUNK (T/R) [dB] PATTERNS REMARKS COT/DID 2ND DATA (4W E&M) (2W E&M) -2/-2 -3/-3 -2/-2 -3/-3 -3/-3 0/-6 -3/-3 -3/-8 -12/-11 -6/-6...
Page 236
CM42 COMMAND CODE TITLE: SYSTEM COUNTER DATA/PAD DATA/TRUNK RESTRICTION CLASS CONVERSION Trunk Restriction Class Conversion (PBX ICS) 1ST DATA 2ND DATA REMARKS DATA MEANING DATA MEANING NEAX2000 IVS Trunk Rest. NEAX2400 IMS Trunk Rest. Class 1 (RCA) Class (0 - 15) NEAX2000 IVS Trunk Rest.
Page 237
CM42 COMMAND CODE TITLE: SYSTEM COUNTER DATA/PAD DATA/TRUNK RESTRICTION CLASS CONVERSION Note 1: Initial Data in the Data Table represents the value for the data “NONE”. In this case, the fol- lowing conversion is performed in the Deluxe Traveling Class Mark-CCIS. NEAX2400 to NEAX2000 IVS NEAX2400 NEAX2000 IVS...
[CM44] External Equipment Starting Conditions CM44 COMMAND CODE TITLE: EXTERNAL EQUIPMENT STARTING CONDITIONS FUNCTION: This command assigns the relay (circuit number of the PN-DK00) used for controlling external equip- ment. PRECAUTION: None ASSIGNMENT PROCEDURE: CIRCUIT DATA 1 DATA 2 ST + 44 + DE + NUMBER + DE + + EXE (2 digits) (2 digits)
Page 239
CM44 COMMAND CODE TITLE: EXTERNAL EQUIPMENT STARTING CONDITIONS DATA 1 DATA 2 RELATED COMMAND DATA MEANING DATA MEANING External Hold Tone Machine Start External Hold Tone for Music On CM10 (TNT/COT Interface) Hold (DA00-DA09) CM48 External Announcement Machine Start External Announcement Machine CM10 (COT Interface) for wake-up calling...
[CM45] Purpose of PBR/CFT CM45 COMMAND CODE TITLE: PURPOSE OF PBR/CFT FUNCTION: This command is used to define the presence and purpose of PB (DTMF) Receivers (PN-8RST) and conference trunks. This command is also used to make CFTs and PBRs busy. PRECAUTION: None ASSIGNMENT PROCEDURE:...
Page 241
CM45 COMMAND CODE TITLE: PURPOSE OF PBR/CFT DATA TABLE: Initial Data PBR/CFT NUMBER SETTING DATA RELATED COMMAND MEANING MEANING DATA MEANING Make busy condition XX X Make busy CM10-E2xx of PBR In Service Circuit Number (0-3) Card Number (00-15) PBR for incoming Same as Y = 0 Only for incoming CM10-E2xx...
Page 242
CM45 COMMAND CODE TITLE: PURPOSE OF PBR/CFT Initial Data PBR/CFT NUMBER SETTING DATA RELATED COMMAND MEANING MEANING DATA MEANING Receiving dB level of XX X –22.6 dBm –23.3 Circuit –24.0 Number (0-3) –24.8 –25.8 Card Number –27.0 (00-15) –27.7 –28.3 –29.1 –29.8 –30.6...
Page 243
[CM48] Hold/wake-up/timed Reminder/automated Attendant Tone CM48 COMMAND CODE TITLE: HOLD/WAKE-UP/TIMED REMINDER/AUTOMATED ATTENDANT TONE INITIAL FUNCTION: This command determines the kind of tone/tone source on various services; it also determines whether the Announcement Service is provided when a PS in a Wireless Communication System does not answer.
CM48 COMMAND CODE TITLE: HOLD/WAKE-UP/TIMED REMINDER/AUTOMATED ATTENDANT TONE INITIAL Initial Data SENDING PATTERN SETTING DATA RELATED COMMAND MEANING PATTERN MEANING DATA MEANING Wake-Up Tone source XX 00 No Tone Call/Timed of Wake- External Tone Source CM10-DB00, Reminder Up Call/ CM08-183 Timed Kind CM44 Data=0100...
Page 245
CM48 COMMAND CODE TITLE: HOLD/WAKE-UP/TIMED REMINDER/AUTOMATED ATTENDANT TONE INITIAL : Initial Data SENDING PATTERN SETTING DATA RELATED COMMAND MEANING PATTERN MEANING DATA MEANING Dial Tone Progress Not provided Provided Sending Tone for Last Num- ber Redial and Speed Dial When Using LCR 2nd DT Provided...
Page 246
CM48 COMMAND CODE TITLE: HOLD/WAKE-UP/TIMED REMINDER/AUTOMATED ATTENDANT TONE INITIAL : Initial Data SENDING PATTERN SETTING DATA RELATED COMMAND MEANING PATTERN MEANING DATA MEANING Kind of BGM BGM0 DXXX Trunk Number for CM10-DXXX Note 3 each music source CM20-039 BGM9 CM15 YY = 32 CM35 YY = 00 Announcement –...
[CM49] Digital Announcement Trunk CM49 COMMAND CODE TITLE: DIGITAL ANNOUNCEMENT TRUNK FUNCTION: This command is used to define the function of each Digital Announcement Trunk (PN-2DATA) accom- modated into the system. PRECAUTION: None ASSIGNMENT PROCEDURE: DIGITAL ANNOUNCE- TENANT 49YY + DE + MENT TRUNK CIRCUIT NUMBER...
Page 248
CM49 COMMAND CODE TITLE: DIGITAL ANNOUNCEMENT TRUNK DATA TABLE: DIGITAL SENDING DATA ANNOUNCEMENT RELATED TRUNK CIRCUIT/ COMMAND MEANING DATA MEANING TENANT No. Function of XXX: 000 – 127 Digital “XXX” represents the Message Number (00 – 63) CM08 Announce- card number (EB000 – 01: 1st Answering Message of CM10 ment Trunk...
Page 249
CM49 COMMAND CODE TITLE: DIGITAL ANNOUNCEMENT TRUNK DIGITAL SENDING DATA ANNOUNCEMENT RELATED TRUNK CIRCUIT/ COMMAND MEANING DATA MEANING TENANT No. Function of XXX: 000 - 127 03000 Night Announcement Service CM10 Digital CM30 Announce- YY = 02-05 ment Trunk CM41 Y = 0, Function No.
Page 250
CM49 COMMAND CODE TITLE: DIGITAL ANNOUNCEMENT TRUNK DIGITAL SENDING DATA ANNOUNCEMENT RELATED TRUNK CIRCUIT/ COMMAND MEANING DATA MEANING TENANT No. Function of XXX: 000 – 127 Second Announcement of UCD CM17 Y = 2 11 XX Digital delay announcement service UCD CM41 Y = 0 –...
Page 251
CM49 COMMAND CODE TITLE: DIGITAL ANNOUNCEMENT TRUNK DIGITAL SENDING DATA ANNOUNCEMENT RELATED TRUNK CIRCUIT/ COMMAND MEANING DATA MEANING TENANT No. Message No. of XX: Tenant Number Message Number (00 – 63) 1st Answering (00 – 63) assigned by CM49 YY=00 Message of Automated Attendant...
Page 252
CM49 COMMAND CODE TITLE: DIGITAL ANNOUNCEMENT TRUNK DIGITAL SENDING DATA ANNOUNCEMENT RELATED TRUNK CIRCUIT/ COMMAND MEANING DATA MEANING TENANT No. Message No. of 00: When message Message Number (00 – 63) CM48 Y=2 Voice Guide waiting is set assigned by CM49 YY=00 CM49 YY=00- 01: When service is set 17XX...
Page 253
This page is for your notes. THIS PAGE INTENTIONALLY LEFT BLANK. CHAPTER 3 ND-45669 (E) Page 216-2 Addendum-001 Revision 2.1 AUGUST, 1998...
[CM50] Common Route Indial CM50 COMMAND CODE TITLE: COMMON ROUTE INDIAL FUNCTION: This command is used to assign LDNs (Listed Directory Numbers) to DID or Tie lines. When these numbers are dialed into the system, either on an incoming tie line or an incoming C.O. line set up for indialing, the call will appear at a specified call identification key on the attendant’s console.
Page 255
CM50 COMMAND CODE TITLE: COMMON ROUTE INDIAL DATA TABLE: Initial Data KIND OF DATA SETTING DATA CODE MEANING DATA MEANING Two leading digits to be added Digits to be added Note 1 Access Code to be sent out before a Mail Box Number Access Code to be sent out Note 2 to a VMS...
[CM51] Automatic Transfer Destinations CM51 COMMAND CODE TITLE: AUTOMATIC TRANSFER DESTINATIONS FUNCTION: This command is used to define destinations for different types of diversion. PRECAUTION: If a transferred station number for a house phone call and a transferred station number for off-hook alarm are the same, this service is not effective.
Page 257
CM51 COMMAND CODE TITLE: AUTOMATIC TRANSFER DESTINATIONS GROUP NUMBER SETTING DATA MEANING DATA MEANING Tenant 00 Transfer destination of the call when the called Station Number as the station is set to Do Not Disturb. destination of a call Tenant 63 XXXX diversion.
Page 258
CM51 COMMAND CODE TITLE: AUTOMATIC TRANSFER DESTINATIONS GROUP NUMBER SETTING DATA MEANING DATA MEANING Tenant 00 Destination VMS of a call that is set Camp-On VMS Station No. and not answered/Destination VMS of Call Re- Tenant 63 direct. XXXX Tenant 00 Destination VMS station for Call Forwarding- VMS Station No.
[CM52] Hot Line CM52 COMMAND CODE TITLE: HOT LINE FUNCTION: This command is used to assign a Hot Line to stations, ATTCONs and trunks. PRECAUTION: (1) The maximum number of Hot Lines is 100, and the connection is one way from the calling side to the called side.
Page 260
CM52 COMMAND CODE TITLE: HOT LINE DATA TABLE: Hot Line SETTING DATA CALLING/CALLED MEANING DATA MEANING Hot Line Num- Calling Side Station Number/Data Station Number ber 00 ~ 99 XXXX (See CM12 YY = 03) Called Side Station Number/Data Station Number XXXX E000 ATTCON...
[CM53] Trunk Answer From Any Station Restriction CM53 COMMAND CODE TITLE: TRUNK ANSWER FROM ANY STATION RESTRICTION FUNCTION: This command is used to define the conditions for TAS service. PRECAUTION: None ASSIGNMENT PROCEDURE: CONDITION DATA ST + 53Y + DE + CODE + DE + + EXE (1 digit)
[CM56] Intercom Zone Paging Group/Intercom Group CM56 COMMAND CODE TITLE: INTERCOM ZONE PAGING GROUP/INTERCOM GROUP FUNCTION: This command is used to assign the Multiline Terminal station number for Automatic/Manual/Dial Intercom and Internal Zone Paging. PRECAUTION: This command is included in MAT mode menu “A8” (Intercom Group [COM01]). ASSIGNMENT PROCEDURE: DATA SERIAL No.
Page 263
CM56 COMMAND CODE TITLE: INTERCOM ZONE PAGING GROUP/INTERCOM GROUP Initial Data INTERCOM SETTING DATA RELATED COMMAND MEANING DATA MEANING SERIAL No. Assignment of A200 Station Number CM11 Manual Intercom (Primary Extension Number CM12 YY = 03 Number A700 XXXX of the Multiline Terminal to CM90 A201 be set)
[CM58] LDN Diversion CM58 COMMAND CODE TITLE: LDN DIVERSION FUNCTION: This command is used to assign information to each DID or TIE trunk for which incoming calls are to be redirected to an alternative destination. PRECAUTION: This data is valid when CM08-205 is assigned to “0”. ASSIGNMENT PROCEDURE: LDN/TIE DATA...
Page 265
CM58 COMMAND CODE TITLE: LDN DIVERSION Initial Data SETTING DATA MEANING DATA MEANING Tenant number of the LDN assigned by Tenant 00 CM50-01 Tenant 63 None TAS group number assigned by CM44-13 TAS Group 00 TAS Group 63 None Day mode destination of the LDN ATTCON LDN/TIE Key 0 ATTCON LDN/TIE Key 7 TAS (See CM53)
Page 266
CM58 COMMAND CODE TITLE: LDN DIVERSION Initial Data SETTING DATA MEANING DATA MEANING Night mode diversion for non-answering As per YY = 06 destination station None Day mode station number/Abbreviate Code for Outside Party (LDN-Outside) Station No. XXXX Abbreviated Code for Outside Party (XX: 00 - 31, See CM71-66) None Night mode station number/Abbreviate...
[CM59] TAS/ACD/UCD Relay Interruption Pattern CM59 COMMAND CODE TITLE: TAS/ACD/UCD RELAY INTERRUPTION PATTERN FUNCTION: This command is used to assign the interruption pattern on the TAS and ACD/UCD indicators controlled via the PN-DK00 card. PRECAUTION: None ASSIGNMENT PROCEDURE: FUNCTION DATA ST + 59 + DE + NUMBER + DE + + EXE...
[CM5A] Virtual Line – Virtual Trunk Path Setting CM5A COMMAND CODE TITLE: – VIRTUAL LINE VIRTUAL TRUNK PATH SETTING FUNCTION: Specify a path between the virtual line and virtual trunk for Wireless Communication System. PRECAUTION: Combination of the virtual line and the virtual trunk must be as follows: •...
[CM60] ATT Group, Functions CM60 COMMAND CODE TITLE: ATT GROUP, FUNCTIONS FUNCTION: This command is used to assign a number to an ATTCON for access on a tenant basis, and define the consoles’ night switching ability, off-hook ringing, tone ringer, password code for Attendant Lockout and Attendant Programming.
Page 270
CM60 COMMAND CODE TITLE: ATT GROUP, FUNCTIONS Initial Data GROUP NUMBER RELATED COMMAND MEANING DATA MEANING Trunk Restriction Class change by Effective CM12 Note 1 (A0) NT Switch Ineffective YY=01 INITIAL Outgoing call restriction on night Effective CM30 (A2) mode by NT Switch Note 1 Ineffective YY=08...
[CM61] External Key Function CM61 COMMAND CODE TITLE: EXTERNAL KEY FUNCTION FUNCTION: This command is used to activate and specify the function of the switch closure detection circuit (PN-DK00) card when interfaced with external keys. PRECAUTION: This command is included in MAT mode menu “E4” (External Key function [COM02]). ASSIGNMENT PROCEDURE: DATA KEY NUMBER...
[CM62] Tenants For Each Att Group CM62 COMMAND CODE TITLE: INITIAL TENANTS FOR EACH ATT GROUP FUNCTION: This command is used to assign which tenants are handled by each ATTCON Group. PRECAUTION: (1) This command requires a system reset after data setting. (2) Multiple tenants can be assigned to one ATT Group, but one tenant cannot be assigned to more than one ATT Group.
[CM63] Restriction of Inter-Tenant Connection CM63 COMMAND CODE TITLE: RESTRICTION OF INTER-TENANT CONNECTION FUNCTION: This command is used to define the restrictions on inter-tenant access. PRECAUTION: None ASSIGNMENT PROCEDURE: TENANT-A TENANT-B DATA + 63Y + EXE (2 digits) (2 digits) (1 - 4 digits) DATA TABLE: Initial Data...
Page 274
[CM64] Automated Attendant CM64 COMMAND CODE TITLE: AUTOMATED ATTENDANT FUNCTION: This command defines the answering system of the Automated Attendant feature. PRECAUTION: None ASSIGNMENT PROCEDURE: DATA TENANT NUMBER + 64Y + EXE (2 digits) (1 digit) DATA TABLE: : Initial Data SETTING DATA RELATED TENANT...
[CM65] Service Features on Tenant Basis CM65 COMMAND CODE TITLE: SERVICE FEATURES ON TENANT BASIS FUNCTION: This command is used to define the features available in each tenant PRECAUTION: None ASSIGNMENT PROCEDURE: TENANT NUMBER DATA + 65YY + EXE (2 digits) (1 digit) DATA TABLE: Initial Data...
Page 276
[CM65] Service Features on Tenant Basis CM65 COMMAND CODE TITLE: SERVICE FEATURES ON TENANT BASIS Initial Data SETTING DATA RELATED TENANT COMMAND MEANING DATA MEANING RR sending priority when receiv- Send RR (Returned Result) after XX: 00 – 63 ing SCF SMFN Send RR (Returned Result) before SMFN...
[CM71] Memory Allocation for System Speed Dialing CM71 COMMAND CODE TITLE: MEMORY ALLOCATION FOR SYSTEM SPEED DIALING FUNCTION: This command is used to allocate memory area for System Speed Dialing to tenants, attendants and Hot Line outside stations. PRECAUTION: (1) System Speed Dialing has 300 memory locations system-wide; this is referred to as a “Memory Block”...
Page 278
CM71 COMMAND CODE TITLE: MEMORY ALLOCATION FOR SYSTEM SPEED DIALING (3) There is a maximum of 300 memory slots assigned by this command. However, if required, another 1000 memory slots can be added. In this case, the maximum number of digits stored is 16. These additional 1000 memory slots are to be assigned with CM 08-110, 111, 112, 176, and CM73 and CM74.
Page 279
CM71 COMMAND CODE TITLE: MEMORY ALLOCATION FOR SYSTEM SPEED DIALING DATA TABLE: KIND OF CALLING PARTY SETTING DATA MEANING MEANING MEANING Tenant 00 XXXXXX XXX XXX Number of Slots to be Tenant 63 assigned in Block Exclusively for ATTCON First Memory Slot Exclusively for Hot Line Outside Number in Block Call (Related Command: CM52)
[CM72] Stored Number for System Speed Dialing CM72 COMMAND CODE TITLE: STORED NUMBER FOR SYSTEM SPEED DIALING FUNCTION: This command is used to enter the stored number for the System Speed Dialing feature into the memory allocated with CM71. PRECAUTION: (1) When displaying the data, the access code corresponding to the Memory Slot Number is indicated by the very first , and the stored number is indicated by the next...
[CM73] Memory Allocation for Station Speed Dialing CM73 COMMAND CODE TITLE: MEMORY ALLOCATION FOR STATION SPEED DIALING FUNCTION: This command is used to allocate memory areas for Station Speed Dialing to individual stations. PRECAUTION: (1) The allowed number of 10-Slots Memory Blocks per Station Number ranges from 1 to 10. (2) This command is included in the MAT mode menu “E11”...
Page 282
CM73 COMMAND CODE TITLE: MEMORY ALLOCATION FOR STATION SPEED DIALING Note 4: When CM08-252 is assigned as 0, only 3000 Station Speed Dialing numbers can be assigned, and 1000- Slot Memory Block number 0-2 contains 26-digits memory buffers. When CM08-252 is assigned as 1, 4500 Station Speed Dialing numbers can be assigned, and 1000-Slot Memory Block number 0-4 contains 16 digits-memory buffers.
Page 283
CM73 COMMAND CODE TITLE: MEMORY ALLOCATION FOR STATION SPEED DIALING • Concept of the Abbreviated Codes The abbreviated codes for Station Speed Dialing are automatically determined by assigning this command on a station basis (see figure below). • If the quantity of Memory Parcels per Station (or per Station Group) does not exceed 10, then Abbreviated Code = 0 –...
[CM74] Stored Number for Station Speed Dialing CM74 COMMAND CODE TITLE: STORED NUMBER FOR STATION SPEED DIALING FUNCTION: This command is used to enter the stored number, for the Station Speed Dialing feature, into the memory allocated with CM73. PRECAUTION: (1) The stored number, exclusive of any access code, can be a maximum of 16 digits or 26 digits.
[CM76] Digit Conversion on DID Call CM76 COMMAND CODE TITLE: DIGIT CONVERSION ON DID CALL FUNCTION: This command is used to assign the data required for interpreting the dialed-in digits. PRECAUTION: The first digit in the RECEIVED DIGITS field must be assigned, in CM20 Y = 0-3, as a station number 801-811.
Page 286
CM76 COMMAND CODE TITLE: DIGIT CONVERSION ON DID CALL Initial Data SETTING DATA RECEIVED DIGITS REMARKS MEANING DATA MEANING Day/Night Mode X-XXXX: Tenant 00 CM08-264 Distinction of tenant DID Incoming LDN CM35-18 for each station as- Tenant 63 signment by Direct None Depends on trunk Inward Dialing...
Page 287
CM76 COMMAND CODE TITLE: DIGIT CONVERSION ON DID CALL Data settings for Day/Night Mode Distinction of tenant. An explanation of tenant selection method for Day/Night Mode change, when a Direct Inward Dialing call terminates, is shown below as a tree diagram for system data registration. Example: data settings for tenant associated with each station assignment number (CM08-264-0) Terminates at station set by CM76-0...
Page 288
CM76 COMMAND CODE TITLE: DIGIT CONVERSION ON DID CALL Example: data settings associated with station tenant or trunk tenant (CM08-264-1) Station tenant DAY/NIGHT Terminates at station set by mode change set by CM76-0 CM76-0 NIGHT Terminates at station set by CM76-1 CM76-0 CM76-1...
[CM77] Station/Trunk Name Asignment CM77 COMMAND CODE TITLE: Station/Trunk Name Asignment FUNCTION: This command is used to assign the name of each station and trunk route which is displayed on Multiline Terminal or ATTCON. PRECAUTION: This command is included in MAT mode menu “E7” (Name Display [COM02]). ASSIGNMENT PROCEDURE: TRUNK NAME STATION NUMBER...
[CM78] Destination of Split Call Forwarding CM78 COMMAND CODE TITLE: DESTINATION OF SPLIT CALL FORWARDING FUNCTION: This command is used to assign the called number of Split Call Forwarding. PRECAUTION: None. ASSIGNMENT PROCEDURE: • To assign destination of Split Call Forwarding 1ST DATA 2ND DATA (3 digits)
[CM81] Toll Restriction Pattern on Each Trunk Restriction Class CM81 COMMAND CODE TITLE: TOLL RESTRICTION PATTERN ON EACH TRUNK RESTRICTION CLASS FUNCTION: Toll call restriction is controlled by combinations of the toll office code dialed and assigned station trunk restriction class. With respect to toll call restriction, there are five kinds of trunk restriction classes: Unrestricted (RCA), Non-Restricted-1 (RCB), Non-Restricted-2 (RCC), Semi-Restricted-1 (RCD), and Semi-Restricted-2 (RCE).
Page 293
CM81 COMMAND CODE TITLE: TOLL RESTRICTION PATTERN ON EACH TRUNK RESTRICTION CLASS DATA TABLE: TRUNK RESTRICTION ASSIGNMENT DATA MEANING MEANING DATA MEANING Toll Restriction Pattern:01 Unrestricted (RCA) Restricted Number for each Class:13 Non-Restricted-1 (RCB) Not used Non-Restricted-2 (RCC) Not used Allowed Semi-Restricted-1 (RCD) Semi-Restricted-2 (RCE)
[CM85] Maximum Digits on C.O. Calls CM85 COMMAND CODE TITLE: MAXIMUM DIGITS ON C.O. CALLS FUNCTION: This command is used to define the maximum number of digits which can be dialed, after C.O. access, given a specific first digit. PRECAUTION: (1) This command is included in MAT mode menu “B4”...
[CM88] Automatic Pause Entry Table CM88 COMMAND CODE TITLE: AUTOMATIC PAUSE ENTRY TABLE FUNCTION: This command is used to define the pause which is automatically provided with particular dialed digits on an outgoing call. PRECAUTION: None ASSIGNMENT PROCEDURE: BLOCK NUMBER DATA (2 digits) (1 - 7 digits)
[CM8A] LCR/Toll Restriction Development Table CM8A COMMAND CODE TITLE: LCR/TOLL RESTRICTION DEVELOPMENT TABLE FUNCTION: This command is used to define the development tables used for Least Cost Routing (LCR) and Toll Restriction (TR) features. PRECAUTION: This command is included in MAT mode menu “B5” (L.C.R. & T.R. - Develop - [COM01]) and “B6” (L.C.R.
Page 297
CM8A COMMAND CODE TITLE: LCR/TOLL RESTRICTION DEVELOPMENT TABLE Initial Data 1ST DATA 2ND DATA MEANING DATA MEANING DATA MEANING Date Pattern No. 0 Sunday Route Pattern No. 0 Monday Date Pattern No. 3 Tuesday Route Pattern No. 63 Wednesday (RATN) (YYY = 000 - 063) (RATWN) Thursday...
Page 298
CM8A COMMAND CODE TITLE: LCR/TOLL RESTRICTION DEVELOPMENT TABLE Initial Data 1ST DATA 2ND DATA MEANING DATA MEANING DATA MEANING TR(/LCR) Pattern Designation of Toll Re- Toll Restriction No. 000 (CP) striction Pattern No. Pattern No. 00 specified by CM81 Toll Restriction TR(/LCR) Pattern Pattern No.
Page 299
CM8A COMMAND CODE TITLE: LCR/TOLL RESTRICTION DEVELOPMENT TABLE Initial Data 1ST DATA 2ND DATA MEANING DATA MEANING DATA MEANING Route Pattern No. 0 Designation of next table Route Pattern No. 0 (No.) (Route Pattern No.) Route Pattern No. 63 Route Pattern No. 63 (RATN) (RATN) 0000...
Page 300
CM8A COMMAND CODE TITLE: LCR/TOLL RESTRICTION DEVELOPMENT TABLE Initial Data 1ST DATA 2ND DATA MEANING DATA MEANING DATA MEANING Area Code Area Code Route Pattern No. 0 Development (Max. 8 digits) 1NXX Pattern No. 0 N: 2-9 Route Pattern No. 63 X: 0-9 (RATN) (YYY = 000 - 063)
Page 301
CM8A COMMAND CODE TITLE: LCR/TOLL RESTRICTION DEVELOPMENT TABLE Initial Data 1ST DATA 2ND DATA MEANING DATA MEANING DATA MEANING LCR/TR Pattern Designation of Toll Toll Restriction No. 000 (CP) Restriction Pattern No. Pattern No. 00 specified by CM81 (LPN) TR(/LCR) Pattern Toll Restriction No.
Page 302
CM8A COMMAND CODE TITLE: LCR/TOLL RESTRICTION DEVELOPMENT TABLE Initial Data 1ST DATA 2ND DATA MEANING DATA MEANING DATA MEANING LCR/TR Pattern No. Kind of Called Party International Number National Network (LPN) LCR/TR Pattern No. Local Not used Speed Dial For future use NONE Not Sending Called Party Numbering...
Page 303
CM8A COMMAND CODE TITLE: LCR/TOLL RESTRICTION DEVELOPMENT TABLE Initial Data 1ST DATA 2ND DATA MEANING DATA MEANING DATA MEANING LCR/TR Pattern No. Binary Facility Coding (AT&T) Value MEGACOM800 (LPN) LCR/TR Pattern No. MEGACOM Not used Not used ACCUNET Not used INTERNATIONAL800 AT&T MULTIQUEST NONE...
[CM8A] Multiline Terminal/SN610 ATTCON/Add-On Module Key Assignment CM90 COMMAND CODE TITLE: MULTILINE TERMINAL/SN610 ATTCON/ADD-ON MODULE KEY ASSIGNMENT FUNCTION: This command assigns functions to programmable keys on a Multiline Terminal, an ATTCON, a DESK CON or an Add-On Module. PRECAUTION: (1) “Primary Extension” must always be assigned to any key on each Multiline Terminal or Add-On Module (for ETJ-24DS-1).
Page 321
CM90 COMMAND CODE TITLE: MULTILINE TERMINAL/SN610 ATTCON/ADD-ON MODULE KEY ASSIGNMENT DATA TABLE: Multiline Terminal Initial Data SETTING DATA RELATED COMMAND MEANING DATA MEANING Setting of Functions Station Number CM10 (Key • Primary Extension Number CM11 Data) XXXX (FX-FXXXX) • Multiline Number (ordinary station) •...
Page 322
CM90 COMMAND CODE TITLE: MULTILINE TERMINAL/SN610 ATTCON/ADD-ON MODULE KEY ASSIGNMENT Initial Data SETTING DATA RELATED COMMAND MEANING DATA MEANING Setting of Functions AA01 Loop Line Number for Multiline Terminal CM11 (Key Attendant Position CM15 YY = 71 Data) AA05 CM12 YY = 03 AA11 AAX XX Loop Line No.
Page 323
CM90 COMMAND CODE TITLE: MULTILINE TERMINAL/SN610 ATTCON/ADD-ON MODULE KEY ASSIGNMENT Initial Data SETTING DATA RELATED COMMAND MEANING DATA MEANING Setting of Functions F0XXX (Key 020: Call Pickup-Group (PICK) CM16 Data) 021: Call Pickup-Direct (DPICK) CM15 YY=14 022: Do Not Disturb (DND) CM15 YY=19 024: Automatic Wake Up/ CM15 YY=13...
Page 324
CM90 COMMAND CODE TITLE: MULTILINE TERMINAL/SN610 ATTCON/ADD-ON MODULE KEY ASSIGNMENT : Initial Data SETTING DATA RELATED COMMAND MEANING DATA MEANING Setting of Functions F0XXX (Key 067: System Speed Dialing Data) (300 memory) 068: System Speed Dialing (1000 memory) 069: Last Number Redial-(LAST) CM08-177, 178 085: Account Code (ACC) CM15 YY=30...
Page 325
CM90 COMMAND CODE TITLE: MULTILINE TERMINAL/SN610 ATTCON/ADD-ON MODULE KEY ASSIGNMENT Initial Data SETTING DATA RELATED COMMAND MEANING DATA MEANING Setting of Functions F1XXX (Key 007: DTMF Additional Dial CM41 Data) (Programmable) (PBPRG) Function No. 14 008: DTMF Additional Dial (Fixed CM35 YY=26 Width) (PBIX) 009: Hooking Signal sent to outside...
Page 326
CM90 COMMAND CODE TITLE: MULTILINE TERMINAL/SN610 ATTCON/ADD-ON MODULE KEY ASSIGNMENT Initial Data SETTING DATA RELATED COMMAND MEANING DATA MEANING Setting of Functions F1XXX 085: Voice Message Waiting Service- CM15 (Key Individual Set when called station is YYY=100, 102 Data) no answer or busy 090: Headset/Handset For ADA-J, Note: Used to switch to headset or...
Page 327
CM90 COMMAND CODE TITLE: MULTILINE TERMINAL/SN610 ATTCON/ADD-ON MODULE KEY ASSIGNMENT Initial Data SETTING DATA RELATED COMMAND MEANING DATA MEANING Setting of Functions F20XX (Key DATA (DATA) CM1A Data) AUTO/DISP (A/D) CMA1 YY = 01 DTX (DTX) DISP (DISP) AUTO (AUTO) CMA1 YY = 01 DATA DND (D DND) F3XXX...
Page 328
CM90 COMMAND CODE TITLE: MULTILINE TERMINAL/SN610 ATTCON/ADD-ON MODULE KEY ASSIGNMENT Initial Data SETTING DATA RELATED COMMAND MEANING DATA MEANING Setting of Functions F6010 Call Termination from FX Line 0 (FX0) CM35 YY=15 (Key Data) F6017 Call Termination from FX Line 7 (FX7) F6020 Call Termination from WATS Line 0 CM35 YY=15...
Page 329
CM90 COMMAND CODE TITLE: MULTILINE TERMINAL/SN610 ATTCON/ADD-ON MODULE KEY ASSIGNMENT SN610 ATTCON / SN716 DESKCON • ATTCON Incoming Call Identification Key STANDARD SETTING RELATED FUNCTION REMARKS DATA COMMAND MEANING SETTING Setting of F6000 C.O. Incoming 0 (LDN0) LDN0 CM35 (Key Function YY=15 data)
Page 330
CM90 COMMAND CODE TITLE: MULTILINE TERMINAL/SN610 ATTCON/ADD-ON MODULE KEY ASSIGNMENT STANDARD SETTING RELATED FUNCTION REMARKS DATA COMMAND MEANING SETTING Setting of F6060 Operator Call (ATND) ATND (Key Function F6061 Recall (RCL) data) F6062 Serial Call Termination (SRL) CM90 – F6105 F6063 Call Forwarding-No Answer CM51...
Page 331
CM90 COMMAND CODE TITLE: MULTILINE TERMINAL/SN610 ATTCON/ADD-ON MODULE KEY ASSIGNMENT • ATTCON Function Keys STANDARD SETTING RELATED FUNCTION REMARKS DATA COMMAND MEANING SETTING Setting of F6100 Room Cut Off (RC) For Hotel ATTCON (Key Function Note 1 F6101 Message Waiting (MW) data) F6102 Do Not Disturb (DND)
Page 332
CM90 COMMAND CODE TITLE: MULTILINE TERMINAL/SN610 ATTCON/ADD-ON MODULE KEY ASSIGNMENT STANDARD SETTING RELATED FUNCTION REMARKS DATA COMMAND MEANING SETTING Setting of F6121 Last umber Redial/Stack Dial (Key Function F6122 Calling Number/Calling data) Name Display for Caller ID Class F6123 Transfer to VMS F6144 Call Park-System CM08-445...
Page 333
CM90 COMMAND CODE TITLE: MULTILINE TERMINAL/SN610 ATTCON/ADD-ON MODULE KEY ASSIGNMENT • ATTCON Multi-Function Keys ATTCON SETTING RELATED STATUS MEANING FUNCTION REMARKS DATA COMMAND Idle State F6100 Room Cut Off (Idle State) (RCOF) F6102 Do Not Disturb (DND) F6104 Reset (RESET) F6110 Mode (MODE) F6111...
Page 334
CM90 COMMAND CODE TITLE: MULTILINE TERMINAL/SN610 ATTCON/ADD-ON MODULE KEY ASSIGNMENT ATTCON SETTING RELATED STATUS MEANING FUNCTION REMARKS DATA COMMAND When accessing F6100 Room Cut Off For Hotel/Motel (Hotel/ Hotel/Motel (RCOF) ATTCON Motel) features Note 1 F6101 Message Waiting (MW) F6102 Do Not Disturb (DND) F6104...
Page 335
CM90 COMMAND CODE TITLE: MULTILINE TERMINAL/SN610 ATTCON/ADD-ON MODULE KEY ASSIGNMENT Note 5: If no data is set, the Multi-Function keys are automatically set by initial data/Resident System Program as follows: • Idle State 10:23 AM TUE 12 MODE: Mode PROG: Programming LOCKOUT/DAY MODE...
Page 336
CM90 COMMAND CODE TITLE: MULTILINE TERMINAL/SN610 ATTCON/ADD-ON MODULE KEY ASSIGNMENT Add-On Module Initial Data SETTING DATA RELATED COMMAND MEANING DATA MEANING Setting of Functions Station Number CM10 (Key • Primary Extension Number (FX-FXXXX) CM11 Data) XXXX • Multiline Number (Ordinary Station) (STA No.) •...
Page 337
CM90 COMMAND CODE TITLE: MULTILINE TERMINAL/SN610 ATTCON/ADD-ON MODULE KEY ASSIGNMENT Initial Data SETTING DATA RELATED COMMAND MEANING DATA MEANING Setting of Functions F11XX CM73 (Key (SPD0099) CM74 Data) 00: Station Speed Dialing 00 99: Station Speed Dialing 99 Setting of Functions F0043 Day/Night Key Note: Any one of key numbers 87...
[CM93] Prime Line CM93 COMMAND CODE TITLE: PRIME LINE FUNCTION: This command is used to assign the prime line to a station line or a trunk line on a Multiline Terminal. The prime line is the line seized when the Multiline Terminal user goes off-hook or presses the speaker button.
[CM94] Multiline Terminal One-Touch Memory CM94 COMMAND CODE TITLE: MULTILINE TERMINAL ONE-TOUCH MEMORY FUNCTION: This command is used to assign memory for the storage of numbers accessed by the one-touch keys on a Multiline Terminal. PRECAUTION: term This command is included in MAT mode menu “A2” (D Key [COM01]).
[CM96] DSS Console Number CM96 COMMAND CODE TITLE: DSS CONSOLE NUMBER FUNCTION: This command is used to assign a DSS Console to a station, Multiline Terminal or attendant console. PRECAUTION: This command is included in MAT mode menu “E3” (DSS Console No. & Keys [COM02]). ASSIGNMENT PROCEDURE: DSS CONSOLE DATA...
[CM97] DSS Console Key Assignment CM97 COMMAND CODE TITLE: DSS CONSOLE KEY ASSIGNMENT FUNCTION: This command assigns the station numbers and trunk numbers to the keys on each DSS Console. PRECAUTION: This command is included in MAT mode menu “E3” (DSS Console No. & Keys [COM02]). CHAPTER 3 ND-45669 (E) Page 304...
Page 344
CM97 COMMAND CODE TITLE: DSS CONSOLE KEY ASSIGNMENT DATA TABLE: SETTING DATA DSS KEY RELATED CONSOLE NUMBER COMMAND DATA MEANING NUMBER Station Number CM10 CM11 XXXX (See CM10, DXXX Trunk Number CM10 E100-E131) (XXX = 000-255) CM30 YY = 02, 03,19 F13XX CM08-244 Day/Night Mode change by Tenant 00...
[CM98] Add-On Module Number CM98 COMMAND CODE TITLE: ADD-ON MODULE NUMBER FUNCTION: This command is used to assign the Add-On Module to the Primary Extension Number of a Multiline Terminal. PRECAUTION: (1) One Add-On Module Number can be assigned for each Primary Extension Number of a Multiline Terminal.
[CM9A] Multiline Terminal Soft Key Assignment CM9A COMMAND CODE TITLE: MULTILINE TERMINAL SOFT KEY ASSIGNMENT FUNCTION: This command assigns functions for the Soft Keys on a Multiline Terminal. PRECAUTION: None ASSIGNMENT PROCEDURE: DATA + 9AYY + STATUS NUMBER (1-6 digits) SOFT KEYS NUMBER (4 digits) ND-45669 (E)
Page 347
CM9A COMMAND CODE TITLE: MULTILINE TERMINAL SOFT KEY ASSIGNMENT DATA TABLE: 1ST DATA 2ND DATA MEANING DATA MEANING DATA MEANING Setting of aabb F5002 Scroll key to Function for change the Soft key aa bb each Pattern indication Number (Pat- Soft Key Number (00~15) tern Number XXXXX...
Page 348
CM9A COMMAND CODE TITLE: MULTILINE TERMINAL SOFT KEY ASSIGNMENT • Example of CM9A Data Assignment 1ST DATA of 2ND DATA of INDICATION STATUS MEANING YY=03 YY=03 (YY=13) 0000 Idle F1017 MIC ON/OFF 0100 During dialing F1001 Save & Repeat S & R (Holding no call) 0101 F0021...
Page 349
CM9A COMMAND CODE TITLE: MULTILINE TERMINAL SOFT KEY ASSIGNMENT • Example of CM9A Data Assignment (Continued) 1ST DATA of 2ND DATA of INDICATION STATUS MEANING YY=03 YY=03 (YY=13) 1200 During live recording/af- F1096 Address Addrs ter live recording to 1201 F1092 Pause Pause...
Page 350
This page is for your notes. THIS PAGE INTENTIONALLY LEFT BLANK. ND-45669 (E) CHAPTER 3 Addendum-002 Page 311-2 JANUARY, 1999 Revision 2.2...
[CMA0] Type Of Data Adapter CMA0 COMMAND CODE TITLE: TYPE OF DATA ADAPTER FUNCTION: This command is used to specify the type of Data Adapter used for accommodating a Data Terminal to the data station. PRECAUTION: This command is included in MAT mode menu “E5” (Data Station Attribute [COM02]). ASSIGNMENT PROCEDURE: DATA STATION DATA...
[CMA1] Data Terminal Attribute Data CMA1 COMMAND CODE TITLE: DATA TERMINAL ATTRIBUTE DATA FUNCTION: This command is used to define the attribute data (terminal characteristics data for data communications) of each data terminal. PRECAUTION: This command is included in MAT mode menu “E5” (Data Station Attribute [COM02]). ASSIGNMENT PROCEDURE: DATA STATION DATA...
Page 353
CMA1 COMMAND CODE TITLE: DATA TERMINAL ATTRIBUTE DATA Initial Data SETTING DATA RELATED COMMAND MEANING DATA MEANING Data Speed 50 bps Note: When using Data (SPEED) 75 bps Port Controller 110 bps (DPC), the 50 bps 150 bps through 300 bps 200 bps are converted to 300 bps...
Page 354
CMA1 COMMAND CODE TITLE: DATA TERMINAL ATTRIBUTE DATA Initial Data SETTING DATA RELATED COMMAND MEANING DATA MEANING Type of Code ASCII (7-bit) + even parity (CHR) ASCII (7-bit) + odd parity ASCII (7-bit) + parity (0) ASCII (7-bit) + parity (1) JIS (7-bit) + even parity JIS (7-bit) + odd parity JIS (8-bit)
[CMA5] Nailed Down Connection CMA5 COMMAND CODE TITLE: NAILED DOWN CONNECTION FUNCTION: This command is used to define a nailed-down connection, which provides a fixed connection between data stations, data station and DTI (Digital Trunk Interface) or DTIs. PRECAUTION: None ASSIGNMENT PROCEDURE: ST + A5YY + DE + DATA STATION NUMBER (A) TRUNK NUMBER (A)
[CMA6] Attribute Data For RS-232C Port On AP01 CMA6 COMMAND CODE TITLE: ATTRIBUTE DATA FOR RS-232C PORT ON AP01 FUNCTION: This command is used to assign the attribute data for the RS-232C port on the PN-AP01 card. PRECAUTION: None ASSIGNMENT PROCEDURE: DATA ST + A6YY + DE + 3 + (1 - 2 digits) + EXE...
Page 357
CMA6 COMMAND CODE TITLE: ATTRIBUTE DATA FOR RS-232C PORT ON AP01 Initial Data SETTING DATA RECOMMENDED SETTING MEANING DATA MEANING Stop Bit 2-Stop Bit 1-Stop Bit Type of Code ASCII (7-bit) + even parity ASCII (7-bit) + odd parity ASCII (7-bit) + parity (0) ASCII (7-bit) + parity (1) JIS (7-bit) + even parity JIS (7-bit) + odd parity...
Page 358
CMA6 COMMAND CODE TITLE: ATTRIBUTE DATA FOR RS-232C PORT ON AP01 Initial Data SETTING DATA RECOMMENDED SETTING MEANING DATA MEANING Kind of procedure Free Wheel Not used ND-45669 (E) CHAPTER 3 Page 319 Revision 2.0...
[CMA7] CCIS Channel Data CMA7 COMMAND CODE TITLE: CCIS CHANNEL DATA FUNCTION: This command assigns the various data to each Common Channel Handler (CCH) provided. PRECAUTION: None ASSIGNMENT PROCEDURE: DATA ST + A7YY + DE + CCH No. (0-3) + DE + (1 - 5 digits) + EXE DATA TABLE: Initial Data...
Page 360
CMA7 COMMAND CODE TITLE: CCIS CHANNEL DATA Initial Data SETTING DATA RELATED COMMAND MEANING DATA MEANING Assignment of the Centralized Fault 00001 Point Code of Centralized Fault Re- Reporting destination porting office 16367 Assignment of the Originating Of- Originating Office Number fice Number 9999 Assignment of the ACM signal wait-...
[CMA8] CCIS Routing Label Assignment CMA8 COMMAND CODE TITLE: CCIS ROUTING LABEL ASSIGNMENT FUNCTION: This command is used to assign a destination office for a message to be transferred (e.g. service informa- tion) and the Common Channel Handler (CCH) which will accommodate the message. PRECAUTION: None ASSIGNMENT PROCEDURE:...
[CMA9] ISDN D-Channel Assignment CMA9 COMMAND CODE TITLE: ISDN D-CHANNEL ASSIGNMENT INITIAL FUNCTION: This command is used to assign various data to each D-Channel Handler (DCH) for ISDN-Primary Rate Access. PRECAUTION: This command requires a system reset after data setting. ASSIGNMENT PROCEDURE: 2nd DATA ST + A9YY + DE + DCH No.
[CMAA] DTI/DCH/CIR Card Functions CMAA COMMAND CODE TITLE: DTI/DCH/CIR CARD FUNCTIONS FUNCTION: This command assigns functions to DTI, BRI and DCH card. PRECAUTION: None ASSIGNMENT PROCEDURE: DATA SLOT NUMBER + AAYY + (1-2 digits) (04-15) DATA TABLE: Initial Data SETTING DATA RELATED COMMAND MEANING...
[CMAD] ZT Calling Area/Pad Data Assignment CMAD COMMAND CODE TITLE: ZT CALLING AREA/PAD DATA ASSIGNMENT FUNCTION: This command assigns the calling area and PAD data for each ZT. PRECAUTION: None ASSIGNMENT PROCEDURE: SETTING DATA ZT NUMBER + ADYY + (2-5 digits) (3 digits) DATA TABLE: Initial Data...
[CMAE] ZT Operation Data Assignment CMAE COMMAND CODE TITLE: ZT OPERATION DATA ASSIGNMENT FUNCTION: This command is used for assigning the ZT Operation data. PRECAUTION: None ASSIGNMENT PROCEDURE: 1ST DATA SETTING DATA AEYY (2 digits) (2-10 digits) DATA TABLE: Initial Data 1ST DATA SETTING DATA MEANING...
Page 367
CMAE COMMAND CODE TITLE: ZT OPERATION DATA ASSIGNMENT Initial Data 1ST DATA SETTING DATA MEANING DATA MEANING DATA MEANING Network ID (for Network ID Assign- 00000-65534 Network ID Roaming Service) ment NONE INITIAL CHAPTER 3 ND-45669 (E) Page 327-1 Addendum-001 Revision 2.1 AUGUST, 1998...
CMAF COMMAND CODE TITLE: VISITOR PS DATA ASSIGNMENT FUNCTION: This command assigns the Visitor PS data. PRECAUTION: This data setting is valid when DBM (AP00) card is online. ASSIGNMENT PROCEDURE: 1ST DATA 2ND DATA AFYYY (1-7 digits) (1-5 digits) DATA TABLE: : Initial Data 1ST DATA 2ND DATA...
Page 369
CMAF COMMAND CODE TITLE: VISITOR PS DATA ASSIGNMENT Initial Data 1ST DATA 2ND DATA MEANING DATA MEANING DATA MEANING Route Selection Pattern Trunk Restriction Class Route Selection Pattern Number for the Trunk sent from Home PBX Restriction Class sent 01: Unrestricted (RCA) from the Home PBX 02: Nonrestricted 1 (RCB) 03: Nonrestricted 2 (RCC)
Page 370
This page is for your notes. THIS PAGE INTENTIONALLY LEFT BLANK. ND-45669 (E) CHAPTER 3 Addendum-001 Page 327-4 AUGUST, 1998 Revision 2.1...
[CMB0] Peg Count CMB0 COMMAND CODE TITLE: PEG COUNT FUNCTION: This command allows accumulated data of use for maintenance purposes to be read from the system PEG counter. Data can be cleared after reading. PRECAUTION: (1) When the system is reset, the contents in the memories of the PEG counter are all cleared. (2) This command is included in MAT mode menu “D1”...
Page 372
CMB0 COMMAND CODE TITLE: PEG COUNT DATA TABLE: TRUNK STATUS DATA ASSIGNMENT DATA DATA MEANING The number of Outgoing seizures-trunk route 00 – 63 (For "0" CLEAR) (OG Call) The number of tandem connections established (Tandem Conn.) The number of times a busy station was encountered (STA busy) The number of all types of calls to the ATTCON(s) (ATT Call)
Page 373
CMB0 COMMAND CODE TITLE: PEG COUNT TRUNK STATUS DATA ASSIGNMENT DATA DATA MEANING The number of incoming calls terminated to busy tone-Trunk Route 00–63 (For "0" CLEAR) (ICBT Conn.) The number of unanswered incoming calls-Trunk Route 00–63 (IC no answer) The number of register connections on trunk call-Trunk Route 00–63 (ORT Conn.)
Page 374
CMB0 COMMAND CODE TITLE: PEG COUNT DATA TABLE: 1ST DATA SETTING DATA DATA MEANING DATA MEANING Setting of PEG COUNT XXXXXXXX XX XX XX XX Setting of (Measurement Start Time To stop the PEG duration for Start Time) COUNT immediate- Min.
[CMB1] Traffic Measurement CMB1 COMMAND CODE TITLE: TRAFFIC MEASUREMENT FUNCTION: This command is used to measure traffic data of outgoing/incoming trunk calls and to display the data on CAT or MAT. PRECAUTION: None ASSIGNMENT PROCEDURE: 1ST DATA 2ND DATA DATA TABLE: Initial Data 1ST DATA 2ND DATA...
Page 376
CMB1 COMMAND CODE TITLE: TRAFFIC MEASUREMENT Initial Data Setting condition Display data for Before the traffic measure- of traffic measurement Traffic Measure- ment ment During the traffic measure- ment Completed the traffic mea- surement Displaying incoming Trunk No. 000 XXXX Incoming trunk traffic data (4 digits)
[CMB3] UCD Peg Count CMB3 COMMAND CODE TITLE: UCD PEG COUNT FUNCTION: This command allows accumulated traffic data related to the UCD Group to be read from the system. PRECAUTION: This command is included in MAT mode menu “D1” (Peg Count [COM03]). ASSIGNMENT PROCEDURE: •...
Page 378
CMB3 COMMAND CODE TITLE: UCD PEG COUNT DATA TABLE: SETTING DATA TRUNK STATUS MEANING DATA MEANING DATA The number of answered calls on the UCD UCD Station Number (CM17 Y=0) (ANS) station XXXX The number of incoming calls to the UCD UCD Group 00 (IC Call) Group...
[CMD5] ID Code Assignment With AP CMD5 COMMAND CODE TITLE: ID CODE ASSIGNMENT WITH AP FUNCTION: This command sets up the ID codes used for the Authorization Code and Forced Account Code features with the AP01 card. The last two digits of the ID code can be used as a check code which is automati- cally generated according to the data in Y = 0 and Y = 1, if required.
Page 380
CMD5 COMMAND CODE TITLE: ID CODE ASSIGNMENT WITH AP 1ST DATA 2ND DATA MEANING DATA MEANING DATA MEANING ID Code Entry ID Code which is to be ABBCC Setting of Temporary dialed in service. DDEE Service Class (Exclusive of Check A: Type of Temporary X..X Code)
[CMD6] ID Code All Clear With AP CMD6 COMMAND CODE TITLE: ID CODE ALL CLEAR WITH AP FUNCTION: This command is used for deleting all the ID Codes stored in the PN-AP01 card, at one time. PRECAUTION: None ASSIGNMENT PROCEDURE: ST + D60 + DE + 0000 + DE + CCC + EXE CHAPTER 3 ND-45669 (E)
[CMD7] OAI Control Data CMD7 COMMAND CODE TITLE: OAI CONTROL DATA FUNCTION: This command assigns the data to control the OAI facility (MSF/TMF). PRECAUTION: None ASSIGNMENT PROCEDURE: FUNCTION DATA DATA + EXE + DE + ST + D7Y + DE + (2 - 5 digits) (2 - 4 digits) DATA TABLE:...
Page 383
CMD7 COMMAND CODE TITLE: OAI CONTROL DATA Initial Data 1ST DATA 2ND DATA MEANING DATA MEANING DATA MEANING Assignment of the maxi- Setting MSF mode from Number of Terminals mum number of terminals a PB Telephone (PB telephone) to be in terminal mode simulta- neously Assignment of Office No.
Page 384
CMD7 COMMAND CODE TITLE: OAI CONTROL DATA Note 1: OAI Function key number is assigned by CM90. Note 2: The digit code is assigned by CMD7 Y = 6. Note 3: The maximum number of operation codes is 16. Note 4: Digit number is assigned by CMD7 Y = 0. Note 5: Do not use * as a digit code.
[CMD9] Centralized Billing Data Port Assignment CMD9 COMMAND CODE TITLE: CENTRALIZED BILLING DATA PORT ASSIGNMENT FUNCTION: This command is used to assign the data port for sending billing information to a Centralized Office. PRECAUTION: None ASSIGNMENT PROCEDURE: 1ST DATA 2ND DATA + DE D9YY (2 digits)
[CMDB] Calling Number Development Data CMDB COMMAND CODE TITLE: CALLING NUMBER DEVELOPMENT DATA FUNCTION: This command is used to assign the calling number development data for CALLER ID. PRECAUTION: Clearing all data in memory for calling number development (CMDB YY=90) is necessary before assigning the calling number development data by CMDB and CMDC.
Page 387
CMDB COMMAND CODE TITLE: CALLING NUMBER DEVELOPMENT DATA Initial Data 1ST DATA 2ND DATA MEANING DATA MEANING DATA MEANING Ringing Tone 0-1499 Calling Number Depends on CM35 YY=33 Development Table Not used Number assigned by Internal Ringing Tone CMDC External Ringing Tone Calling Number/ Calling Number Display Calling Name Display...
Page 388
CMDB COMMAND CODE TITLE: CALLING NUMBER DEVELOPMENT DATA Note 1: If assigning the destination station number as below, the Terminating System overrrides CM30 YY=02/03 for the selected Development Table. ****02 : Trunk Line Appearance ****03 : Trunk Line Appearance + TAS ****04 : Direct-in Termination ****09 : Automated Attendant ****11 : ATTCON + Trunk Line Appearance...
[CMDC] Calling Number Development Table CMDC COMMAND CODE TITLE: CALLING NUMBER DEVELOPMENT TABLE FUNCTION: This command is used to assign the calling number development table number for CALLER ID, to each calling number. PRECAUTION: Clearing all data in memory for calling number development (CMDB YY=90) is necessary before assigning the calling number development data by CMDB and CMDC.
[CME0] Initialization CME0 COMMAND CODE TITLE: INITIALIZATION FUNCTION: This command allows the maintenance personnel to reset the system with the CAT. PRECAUTION: If the setting data (Month, Day and Time) is different from the current time of the system clock (set by command 02), any request to initialize the system is not accepted and “DATA ERROR”...
CME5 COMMAND CODE TITLE: STATION, TRUNK LINE MAKE BUSY FUNCTION: This command is used to make busy any station or trunk in the software. PRECAUTION: None ASSIGNMENT PROCEDURE: STATION/TRUNK DATA NUMBER (0/1) DATA TABLE: : Initial Data STATION TRUNK NUMBER SETTING DATA REMARKS MEANING...
[CME6] Call Forwarding Set/Reset From MAT/CAT CME6 COMMAND CODE TITLE: CALL FORWARDING SET/RESET FROM MAT/CAT FUNCTION: This command sets/resets the Call Forwarding service to each station from a MAT/CAT. PRECAUTION: CME6 can be used for any station irrespective of its state. ASSIGNMENT PROCEDURE: STATION No.
[CME9] Password Code CME9 COMMAND CODE TITLE: PASSWORD CODE FUNCTION: This command is used to define the Password Code of each Password Level and the availability of Pass- word Service. PRECAUTION: (1) Before setting the Password code, Function Number 8 (Change of Password) must be set to 0 (Allowed).
[CMEA] Fault Information Store/Display Functions CMEA COMMAND CODE TITLE: FAULT INFORMATION STORE/DISPLAY FUNCTIONS FUNCTION: This command is used for fault maintenance of the PBX. The functions of this command are outlined below: • Storing fault information into the Fault Store Memory upon occurrence of a fault. •...
Page 396
CMEA COMMAND CODE TITLE: FAULT INFORMATION STORE/DISPLAY FUNCTIONS : Initial Data 1ST DATA 2ND DATA RELATED COMMAND MEANING DATA MEANING DATA MEANING Registration of fault (Fault Kind: (External Alarm CM08-450, information into Fault Occurrence) Kind) Information Memory for each fault, and 0: Registration of CM42-01, 50 System Initialization...
Page 397
CMEA COMMAND CODE TITLE: FAULT INFORMATION STORE/DISPLAY FUNCTIONS Initial Data 1ST DATA 2ND DATA RELATED COMMAND MEANING DATA MEANING DATA MEANING Registration of fault (Fault Kind: See the previous page CM08-450, information into Fault Restoration) Information Memory FP/AP card returned for each fault, and to normal condition control of external...
Page 398
CMEA COMMAND CODE TITLE: FAULT INFORMATION STORE/DISPLAY FUNCTIONS Fault Information Display After the following operation: The first screen displays on the MAT/CAT. The fault information is separated into four separate parts, and displayed on four screens. An example of fault information display is provided below: 1st Screen 2nd Screen 2 : 93/3/20...
Page 399
CMEA COMMAND CODE TITLE: FAULT INFORMATION STORE/DISPLAY FUNCTIONS EXPLANATION OF SCREEN INFORMATION (Continued) FAULT RESTORATION FAULT RESTORATION CONTENT KIND NUMBER FP/AP package returned to normal condition Power failure returned to normal condition DTI line returned to normal condition DCH D-channel link connection returned to the normal condition CCH link connection returned to normal condition The number of lockout stations was less than the predetermined number DLC card returned to normal condition...
Page 400
CMEA COMMAND CODE TITLE: FAULT INFORMATION STORE/DISPLAY FUNCTIONS EXPLANATION OF SCREEN INFORMATION (Continued) 3: CPU Kind and FP/AP number for which a fault was detected INDICATION MEANING MP 00 FP 00 - 03 FP Number 0 - 3 AP 04 - 15 AP Card Number 4 - 15 4: Date and Time of Fault Occurrence and Restoration 5-12:Fault-Related Information/Fault Restoration-Related Information...
Page 401
CMEA COMMAND CODE TITLE: FAULT INFORMATION STORE/DISPLAY FUNCTIONS FAULT KIND NUMBER FP/AP No. Power Fail- Power Fail- Power Fail- ure Kind 1 ure Kind 2 ure Kind 3 Fault Detail Kind 9 D-channel circuit No. CCH No. DLC Fail- Station Number ure Kind : Initial Kind (Upper digit) Program address information...
Page 402
CMEA COMMAND CODE TITLE: FAULT INFORMATION STORE/DISPLAY FUNCTIONS : System Initialization related information The address of the program which caused system initialization. Note that, when the program which caused initialization is lpdi, the receive command (4 bytes from the head) is stored. This informa- tion is output in the case of system initialization only when the initial kind in 14 is 02, 03, 06, or : Stack Kind (Lower digit) The number of registrations into H-rank stack was over 16.
Page 403
CMEA COMMAND CODE TITLE: FAULT INFORMATION STORE/DISPLAY FUNCTIONS A: Not used B: Not used C: Not used D: Not used E: Not used F: Not used : D-channel circuit No. • DCH: 00=Channel No. 0 : CCH No. 0–3: CCH No. : DLC Failure Kind 00: Terminal was cut off 02: Short circuit was made on the line...
[CMEC] Battery Release/Line Status Display CMEC COMMAND CODE TITLE: BATTERY RELEASE/LINE STATUS DISPLAY FUNCTION: This command is used for maintenance of the PBX. The functions of this command are outlined below: • Battery release • Line status display for single line telephone or Multiline Terminal PRECAUTION: (1) See Line Status Display in the following pages for details on how to read the status information.
Page 405
CMEC COMMAND CODE TITLE: BATTERY RELEASE/LINE STATUS DISPLAY Line Status Display Operation : COMMAND= ECI+ ECI> X - XXXX + XXXX : XX XX XX XXXX : XX XX XX (Station No.) (b) (c) (d) Explanation of Screen Information: Station Number : X-XXXX (1-4 digits) (b) Analog Line/Digital Line 00: LC (Single Line Tel.) 10: DLC (Multiline Terminal)
[CMEE] Virtual Tie Line Set/Release CMEE COMMAND CODE TITLE: VIRTUAL TIE LINE SET/RELEASE FUNCTION: This command sets/releases the virtual tie line (Event Based CCIS) from a MAT. PRECAUTION: None ASSIGNMENT PROCEDURE: 1ST DATA 2ND DATA + EEY + (1-4 digits) (0/1) DATA TABLE: Initial Data...
FUNCTION: These commands are used only for maintenance. DO NOT USE these commands without the assistance of a NEC engineer. (1) MP Memory Check Sum Display (CME1 Y=0) The following shows the steps for displaying check sums using the CAT...
[CMF2, F3] Special Commands CMF2, F3 COMMAND CODE TITLE: SPECIAL COMMANDS F2, F3 (4) FP Memory Dump (CMF2) The following shows the steps for performing a memory read using the CAT. Note 1, 2 YZXXXX Address Note 3 Note 4 Display XXXX: YY YY YY YY Designated Data of the designated address + 3...
[CMF5] Special Commands CMF5 COMMAND CODE TITLE: SPECIAL COMMANDS (6) Line/Trunk Memory/Alarm Memory Read (CMF5) The following shows the steps for performing a memory read using the MAT/CAT. 1ST DATA READOUT DATA 1ST DATA REMARKS (STATUS INFORMATION) Single Line Station/Virtual Line Station Status of Station/Trunk Number (1-4 digits) X=0-9, A(*), B(#) XXXX...
Page 410
CMF5 COMMAND CODE TITLE: SPECIAL COMMANDS Note 1: A status information associated with Y = 0, 3 will be displayed as shown below. For the meaning of the status information displayed, refer to the Maintenance Manual. Display XXXX: YY YY YY YY Data of the designated Address + 3 Designated Address...
[CMF8] Special Commands CMF8 COMMAND CODE TITLE: SPECIAL COMMANDS FUNCTION: This command is used to assign the ID code to protect a copy of the Key FD. PRECAUTION: This command requires a system reset after data setting. ASSIGNMENT PROCEDURE: 1ST DATA 2ND DATA (1 digit) (1-10 digits)
Page 412
[CMD000] System Features (1) CMD000 COMMAND CODE TITLE: SYSTEM FEATURES (1) D000 FUNCTION: This command is used to assign SMDR and PMS functions. PRECAUTION: None ASSIGNMENT PROCEDURE: 1ST DATA 2ND DATA + D000 + EXE (1 – 3 digits) (0/1) DATA TABLE: Initial Data 1ST DATA...
Page 413
CMD000 COMMAND CODE TITLE: SYSTEM FEATURES (1) D000 Initial Data 1ST DATA 2ND DATA DATA FUNCTION The Authorization Code is printed out. Sending call information for tandem calls through CCIS Not sent To send Sending of detail information of tandem calls to SMDR terminal, Not sent which is set to “4”...
Page 414
CMD000 COMMAND CODE TITLE: SYSTEM FEATURES (1) D000 Initial Data 1ST DATA 2ND DATA DATA FUNCTION MCI/Printer for No. 3 Port Not provided Note: No. 3 port on the PN-AP00 card can be only connected To provide to the VMS or printer which the RTS signal from the PN- AP00 card is not needed.
[CMD001] System Features (2) CMD001 COMMAND CODE TITLE: SYSTEM FEATURES (2) D001 FUNCTION: This command is used to assign various SMDR and PMS functions, and the interface conditions for the SMDR terminal, printer and PMS. PRECAUTION: None ASSIGNMENT PROCEDURE: 1ST DATA 2ND DATA + D001 + EXE...
Page 416
CMD001 COMMAND CODE TITLE: SYSTEM FEATURES (2) D001 Initial Data 1ST DATA DATA 2ND DATA FUNCTION Printout function of Check-In time and Checkout time, when the Not available Checkout is set from a Front Desk Instrument. Available Clearing of Check-In and setting of Room Cutoff service are exe- Not available cuted.
Page 417
CMD001 COMMAND CODE TITLE: SYSTEM FEATURES (2) D001 Initial Data 1ST DATA DATA 2ND DATA FUNCTION Parity for No. 0 Port Note No parity Even parity AP INITIAL Odd parity Note Data Speed for No. 1 Port Not used 300 bps AP INITIAL 1200 bps 2400 bps...
Page 418
CMD001 COMMAND CODE TITLE: SYSTEM FEATURES (2) D001 Initial Data 1ST DATA DATA 2ND DATA FUNCTION Data Speed for No. 3 Port Note Not used 300 bps AP INITIAL 1200 bps 2400 bps 4800 bps 9600 bps Note : 1 bit Stop Bit for No.
Page 419
CMD001 COMMAND CODE TITLE: SYSTEM FEATURES (2) D001 Initial Data 1ST DATA DATA 2ND DATA FUNCTION Priority for data processing on No. 0 Port Note Message format on No. 0 Port Note No data is sent. (when 2nd data of CMD001-80 is set to 4) SMDR (NEAX2400 IMS format) SMDR (NEAX1400 IMS format) AP INITIAL...
Page 420
CMD001 COMMAND CODE TITLE: SYSTEM FEATURES (2) D001 PORT FUNCTION CALL INFORMATION DATA SETTINGS (PROVIDED TERMINAL) SENT TO TERMINAL SMDR C.O. Outgoing Calls CMD001 -80 Tie Line Outgoing Calls CMD016 -XX17 : 1 -XX22 : 1 C.O. Outgoing Calls CMD001 -100 CMD016 -XX16 : 1 PORT FUNCTION...
Page 421
CMD001 COMMAND CODE TITLE: SYSTEM FEATURES (2) D001 Initial Data 1ST DATA DATA 2ND DATA FUNCTION Number of times to resend the Selecting Sequence when NAK is Not used returned in Phase 2 on No. 0 Port Note 1 time AP INITIAL 255 : 255 times...
Page 422
CMD001 COMMAND CODE TITLE: SYSTEM FEATURES (2) D001 Initial Data 1ST DATA DATA 2ND DATA FUNCTION Message format on No. 1 Port (when 2nd data Note No data is sent out of CMD001-100 is set to 4) NEAX2400 IMS format NEAX1400 IMS format AP INITIAL PMS (IMS format)
Page 423
CMD001 COMMAND CODE TITLE: SYSTEM FEATURES (2) D001 Initial Data 1ST DATA DATA 2ND DATA FUNCTION Timer for detecting non-data communication on No. 1 Port No data Note 512 msec increments AP INITIAL 255 : Number of times to resend the Selecting Sequence when NAK is Not used returned in Phase 2 on No.
Page 424
CMD001 COMMAND CODE TITLE: SYSTEM FEATURES (2) D001 Initial Data 1ST DATA DATA 2ND DATA FUNCTION Function of No. 2 Port Note No function Refer to Note 1 SMDR/PMS of CMD001-80. SMDR Printer 0 Printer 1 : MCI Note : 1st Priority for data processing on No.
Page 425
CMD001 COMMAND CODE TITLE: SYSTEM FEATURES (2) D001 Initial Data 1ST DATA DATA 2ND DATA FUNCTION Timer for detecting the terminal no answer on No. 2 Port Note 0 No data AP INITIAL 128 msec increments 255 : Number of times to resend the Selecting Sequence when NAK is No page returned in Phase 2 on No.
Page 426
CMD001 COMMAND CODE TITLE: SYSTEM FEATURES (2) D001 Initial Data 1ST DATA DATA 2ND DATA FUNCTION Function of No. 3 Port Note No function Not used AP INITIAL Not used 16 : Printer 0 17 : Printer 1 24 : Note Priority for data processing on No.
Page 427
CMD001 COMMAND CODE TITLE: SYSTEM FEATURES (2) D001 Initial Data 1ST DATA DATA 2ND DATA FUNCTION Timer for detecting the terminal no answer on No. 3 Port Note Not used AP INITIAL Not used 255 : Note Timer for detecting the end of block on No. 3 Port No data AP INITIAL 512 msec increments...
Page 428
CMD001 COMMAND CODE TITLE: SYSTEM FEATURES (2) D001 Initial Data 1ST DATA DATA 2ND DATA FUNCTION Guard timer between texts on No. 3 Port Note 0-128 msec 128-256 msec 256-384 msec 384-512 msec 512-640 msec Mask Data provision for 1st digit of Authorization Code Not provided No.
CMD001 COMMAND CODE TITLE: SYSTEM FEATURES (2) D001 Table 3-1 through Table 3-5 show the quick reference data table for the SMDR, printer, PMS, and MCI. Table 3-1 Quick Reference Data Table for SMDR (NEAX2400 IMS Format) : Initial Data 1ST DATA MEANING MEANING...
CMD001 COMMAND CODE TITLE: SYSTEM FEATURES (2) D001 Table 3-2 Quick Reference Data Table for SMDR (NEAX1400 IMS Format) : Initial Data 1ST DATA MEANING MEANING DATA PORT 0 PORT 1 PORT 2 PORT 3 – Data speed 2/3/4/5 1200/2400/ 4800/9600 bps –...
CMD001 COMMAND CODE TITLE: SYSTEM FEATURES (2) D001 Table 3-3 Quick Reference Data Table for Printer : Initial Data 1ST DATA MEANING MEANING DATA PORT 0 PORT 1 PORT 2 PORT 3 Data speed 1200 bps ?Stop bit length 2 bits Data length 7 bits Parity...
CMD001 COMMAND CODE TITLE: SYSTEM FEATURES (2) D001 Table 3-4 Quick Reference Data Table for PMS (IMS Format) : Initial Data 1ST DATA MEANING MEANING DATA PORT 0 PORT 1 PORT 2 PORT 3 – Data speed 2/3/4/5 1200/2400/ 4800/9600 bps –...
CMD001 COMMAND CODE TITLE: SYSTEM FEATURES (2) D001 Table 3-5 Quick Reference Data Table for VMS with MCI : Initial Data 1ST DATA MEANING MEANING DATA PORT 0 PORT 1 PORT 2 PORT 3 Data speed 2/3/4/5 1200/2400/ 4800/9600 bps Stop bit length /1/2 1/1.5/2 bits Data length...
Page 434
CMD001 COMMAND CODE TITLE: SYSTEM FEATURES (2) D001 : Initial Data 1ST DATA 2ND DATA DATA FUNCTION Carriage Return (CR) and Line Feed (LF) provision for a printer using 80 For a printer using 136 or 136 characters on NEAX1400 format characters per line, with automatic line feed.
Page 435
CMD001 COMMAND CODE TITLE: SYSTEM FEATURES (2) D001 : Initial Data 1ST DATA 2ND DATA DATA FUNCTION Function of OPE (No. 0-3) LED on the PN-AP00 card Indicates status of data transmission on each port. (See left column.) Indicates status of signal leads on No.
Page 436
CMD001 COMMAND CODE TITLE: SYSTEM FEATURES (2) D001 : Initial Data 1ST DATA 2ND DATA DATA FUNCTION Printout format of Direct Data Entry Printout format 1 Printout format 2 (See left column) • Printout format 1 1995 04/11 17:20 CODE 1 CODE 2 CODE 3 CODE 4...
[CMD003] Time Block Assignment CMD003 COMMAND CODE TITLE: TIME BLOCK ASSIGNMENT D003 FUNCTION: This command is used to determine the Maximum number of Call Records for SMDR. PRECAUTION: None ASSIGNMENT PROCEDURE: 1ST DATA 2ND DATA + D003 + EXE (2 digits) (1-5 digits) DATA TABLE: Initial Data...
[CMD004] Office Number Assignment CMD004 COMMAND CODE TITLE: OFFICE NUMBER ASSIGNMENT D004 FUNCTION: This command is used to assign the office number of the calling party and the office number of the bill- ing office for centralized billing. PRECAUTION: None ASSIGNMENT PROCEDURE: 1ST DATA 2ND DATA...
[CMD012] Station Group Number CMD012 COMMAND CODE TITLE: STATION GROUP NUMBER D012 FUNCTION: By CMD012, a Group Number is to be assigned to each station for sending the tenant information (01- 63) to the SMDR Terminal. PRECAUTION: None ASSIGNMENT PROCEDURE: 1ST DATA 2ND DATA + D012 +...
[CMD015] Station Service Classes CMD015 COMMAND CODE TITLE: STATION SERVICE CLASSES D015 FUNCTION: This command is used to assign the class of service to each station and ATTCON. The class functions are assigned by CMD016. PRECAUTION: None ASSIGNMENT PROCEDURE: 2ND DATA 1ST DATA + DE + + EXE...
[CMD016] Station Features CMD016 COMMAND CODE TITLE: STATION FEATURES D016 FUNCTION: This command assigns the class functions for each class assigned by CMD015. PRECAUTION: None ASSIGNMENT PROCEDURE: 1ST DATA 2ND DATA + D016 + (4 digits) (0/1) DATA TABLE: Initial Data 1ST DATA 2ND DATA DATA...
Page 442
CMD016 COMMAND CODE TITLE: STATION FEATURES D016 Initial Data 1ST DATA 2ND DATA DATA MEANING XX32 Send call information for Tie Line outgoing calls through CCIS : Not sent : Send XX42 Message Waiting Message sending to PMS : Available : Not available XX43 Control of Restriction Message sending to PMS...
[CMD026] Route Index For Call Charge Development CMD026 COMMAND CODE TITLE: ROUTE INDEX FOR CALL CHARGE DEVELOPMENT D026 FUNCTION: This command is used to assign a Development Table Number for each outgoing trunk route. PRECAUTION: Although actual charging is not determined by the PBX, it is necessary to program this command and CMD027 to get SMDR output.
[CMD027] Call Charge Development Tables CMD027 COMMAND CODE TITLE: CALL CHARGE DEVELOPMENT TABLES D027 FUNCTION: This command is used for assigning the charging method to each dialled digit on the basis of each Devel- opment Table designated by CMD026. PRECAUTION: None ASSIGNMENT PROCEDURE: 1ST DATA...
[CMD031] ROOM STATUS CODE CMD031 COMMAND CODE TITLE: ROOM STATUS CODE D031 FUNCTION: This command is used to assign the desired functions for each Room Status Code which is dialed from a guest room or a Front Desk Terminal PRECAUTION: None ASSIGNMENT PROCEDURE: 1ST DATA...
Page 446
CMD031 COMMAND CODE TITLE: ROOM STATUS CODE D031 Example: The table below shows the examples of functions by this command. FUNCTION NUMBER ROOM STATUS CODE Check In (Note) Check Out (Note) Under Cleaning Cleaning Finished Check Finished Out of Service Note: The Room Status Codes for Check In and Check Out are to be assigned by means of CMD001 –...
[CMD033] Route Index For Call Development CMD033 COMMAND CODE TITLE: ROUTE INDEX FOR CALL DEVELOPMENT D033 FUNCTION: This command is used to assign a Type of Call Identifying Development Table for each outgoing trunk route. PRECAUTION: Although the type of Call Identifier has no meaning for the U.S. market, this command and CMD034 must be assigned to get SMDR output.
[CMD034] Call Development Tables CMD034 COMMAND CODE TITLE: CALL DEVELOPMENT TABLES D034 FUNCTION: This command is used to assign Type of Call to the dialed digits on each Type of Call Identifying Table Number assigned by CMD033. PRECAUTION: None ASSIGNMENT PROCEDURE: 1ST DATA 2ND DATA + D034...
Page 449
CMD034 COMMAND CODE TITLE: CALL DEVELOPMENT TABLES D034 Example: Call Development Tables are assigned according to the following table. Command D033 Command D034 ROUTE 0 ISD Call (000) ACCESS CODE = 0 Toll Call (01 - 09) Local Call (2 - 9) DIGIT TYPE OF CALL ISD Call...
[CMD035] Designation Of Printer CMD035 COMMAND CODE TITLE: DESIGNATION OF PRINTER D035 FUNCTION: This command is used to designate the printer for printout by key operation at each Front Desk Instru- ment. PRECAUTION: None ASSIGNMENT PROCEDURE: 1ST DATA 2ND DATA ST + D035 + DE + + DE + + EXE...
[CMD100] System Data Partial Clear CMD100 COMMAND CODE TITLE: AP OFF LINE SYSTEM DATA PARTIAL CLEAR D100 FUNCTION: This command is used to delete the data related only to the designated Command Code among the Sys- tem Data for Billing and for assigning “0” as the data. PRECAUTION: None ASSIGNMENT PROCEDURE:...
[CMD101] System Data All Clear CMD101 COMMAND CODE TITLE: AP OFF LINE SYSTEM DATA ALL CLEAR D101 FUNCTION: This command is used to delete all the System Data for Billing and for assigning the initial data. PRECAUTION: None ASSIGNMENT PROCEDURE: + D101 0000 DE +...
[CMD102] Additional Memory Clear CMD102 COMMAND CODE TITLE: AP OFF LINE ADDITIONAL MEMORY CLEAR D102 FUNCTION: When mounting additional memory (SRAM card), this command is used to delete its stored data. PRECAUTION: None ASSIGNMENT PROCEDURE: 0000 + D102 DE + + EXE (4 digits) Note 1: By entering the 1st data “0000”, the status of the additional memory (SRAM card) will display...
RESIDENT SYSTEM PROGRAM CHAPTER 4 RESIDENT SYSTEM PROGRAM 1. GENERAL The resident system program generates system data automatically according to the system hardware configu- ration, thereby providing immediate operation and shorter programming time. When activated, the system scans hardware configuration (such as line/trunk card location) and assigns the system data (such as station numbers, trunk numbers, etc.) according to a predetermined generic program assignment.
RESIDENT SYSTEM PROGRAM 4. PROGRAMMED DATA TABLES • Basic Service Feature (CM08) The following data is assigned on a per service feature basis. Table 4-1 Basic Service Feature : Initial Data CM08 DATA DATA DATA DATA DATA DATA DATA FEATURE FEATURE FEATURE FEATURE...
RESIDENT SYSTEM PROGRAM • Station Number, Trunk Number, Card Number (CM10) The following data is assigned according to the sequential slot location number of the associated circuit cards. Table 4-2 Station Number, Trunk Number, Card Number CARD PURPOSE ASSIGNED DATA REMARKS PN-4LC Single Line Telephone...
RESIDENT SYSTEM PROGRAM • Station Class Data (CM12, 13) The following data is assigned on a per station basis. Table 4-3 Station Class Data: Initial Data CM10 CM12 STATION No. TRUNK No. DAY NIGHT D000 CARD No. (1–5 DIGITS) xxxx D255 xxxx : Initial Data...
RESIDENT SYSTEM PROGRAM • Number Plan (CM20) The following data is assigned for access code of each service feature. Table 4-4 Numbering Plan CM20 Y (0–3) ACCESS CODE SETTING DATA SERVICE FEATURES Operator Call Call Hold 2, 3 or 4 First Digit of Three Digit Station Number Internal Zone Paging Group 0...
Page 459
RESIDENT SYSTEM PROGRAM Table 4-4 Numbering Plan (Continued) CM20 Y (0–3) ACCESS CODE SETTING DATA SERVICE FEATURES Trunk Access Code RT00 RT01 RT02 RT04 RT05 RT06 RT07 Individual Trunk Access Trunk Queuing – Outgoing /Call Back Cancel Camp-On by Station (Transfer Method) Camp-On by Station (Call Waiting Method) Executive Override Call Forwarding –...
RESIDENT SYSTEM PROGRAM • Trunk Data (CM30) The following data is assigned according to the type of trunk card. Table 4-5 Trunk Data : Initial Data CM30 TYPE OF TRUNK CARD XXXX XXXX EBXXX EBXXX PN-4COT NONE NONE NONE PN-2ODT NONE NONE NONE...
Page 461
RESIDENT SYSTEM PROGRAM Table 4-5 Trunk Data (Continued) : Initial Data CM30 TYPE OF TRUNK CARD XXXX PN-4COT NONE Note NONE Note PN-2ODT NONE NONE Note: C.O. Line Numbers (YY = 19) are assigned as follows: 1XXX Trunk Number (000-255) CHAPTER 4 ND-45669 (E) Page 418...
RESIDENT SYSTEM PROGRAM • Trunk Route Data (CM35) The following data is assigned on a trunk route basis. Table 4-6 Trunk Route Data CM35 YY/YYY TRUNK NO. OF ACCESS TRUNK ROUTE TRUNKS CODE KIND E&M) E&M) – WATS CCSA ND-45669 (E) CHAPTER 4 Page 419 Revision 2.0...
Page 464
RESIDENT SYSTEM PROGRAM Table 4-6 Trunk Route Data (Continued) CM35 YY/YYY TRUNK ROUTE NONE NONE ND-45669 (E) CHAPTER 4 Page 421 Revision 2.0...
Page 465
RESIDENT SYSTEM PROGRAM Table 4-6 Trunk Route Data (Continued) CM35 YY/YYY TRUNK ROUTE CHAPTER 4 ND-45669 (E) Page 422 Revision 2.0...
Page 466
RESIDENT SYSTEM PROGRAM Table 4-6 Trunk Route Data (Continued) CM35 YY/YYY TRUNK ROUTE ND-45669 (E) CHAPTER 4 Page 423 Revision 2.0...
Page 467
RESIDENT SYSTEM PROGRAM • Attendant Group, Function (CM60) The following data is assigned to SN610 ATTCONs provided. CM60 YY = 00 ATT NUMBER (GROUP No.) : ATT Group 0 • Tenant for Each ATT Group (CM62) The following data is assigned to ATTCONs within ATT Group 0. CM62 Y = 0 TENANT NUMBER...
RESIDENT SYSTEM PROGRAM • Memory Allocation for System Speed Dialing (CM71) 100 memory slots for System Speed Dialing are assigned for Tenant 01. Table 4-7 Memory Allocation for System Speed Dialing CM71 DATA KIND OF 1ST MEMORY CALLING SLOT No. SLOT No.
RESIDENT SYSTEM PROGRAM • Memory Allocation for Station Speed Dialing [CM73] 10 memories are assigned to Single Line Telephones individually. Table 4-8 Memory Allocation for Station Speed Dialing CM73 SETTING DATA 10 SLOTS NUMBER OF REMARKS 1000 SLOTS POSSIBLE/NOT TYPE OF MEMORY 10 SLOTS MEMORY...
RESIDENT SYSTEM PROGRAM • Multiline Terminal Line Key Data (CM90) The following data is assigned according to the type of terminal. Table 4-9 Multiline Terminal Line Key Data : Initial Data CM90 PRIMARY EXTEN- REMARKS SION = 00 = 01 = 03 = 05 = 00...
RESIDENT SYSTEM PROGRAM • Prime Line (CM93) As shown in Table 4-10, Primary Extension Number is assigned to Prime Line for all Multiline Terminals. Table 4-10 Prime Line CM93 PRIMARY EXTENSION REMARKS SETTING DATA NUMBER (6 DIGITS) (1 – 4 DIGITS) Note: XXX represents Primary Extension Number (200 –...
RESIDENT SYSTEM PROGRAM • Memory Allocation for Multiline Terminal One-Touch Memory [CM94] The following data is assigned on a per Multiline Terminal, with DSS key, basis. Table 4-11 Memory Allocation for One-Touch Key CM94 PRIMARY EXTENSION REMARKS SETTING DATA NUMBER (6 DIGITS) (1 –...
Page 473
This page is for your notes. CHAPTER 4 ND-45669 (E) Page 430 Revision 2.0...