Operating instructions for dishwashers To avoid the risk of accidents or damage to the appliance, it is essential to read these instructions as well as the installation plan before it is in‐ stalled and used for the first time. en-AU, NZ HG05 M.-Nr.
Contents Guide to the appliance................... 6 Appliance overview....................6 Control panel......................7 Display ........................8 Warning and Safety instructions ................9 Caring for the environment ................. 18 Disposal of the packing material................18 Disposing of your old appliance ................18 Energy-saving dishwashing ...................
Page 4
Contents Operation ......................47 Detergent ....................... 47 Adding detergent ....................49 Switching on ......................50 Selecting a programme..................50 Starting the programme ..................51 Display ........................51 Energy management ....................52 At the end of the programme................. 52 Switching off ......................53 Unloading the dishwasher ..................
Page 5
Contents Warranty......................... 81 Optional accessories ................... 82 Electrical connection ................... 84 Water connection....................85 The Miele Waterproof system ................85 Connection to the water supply................85 Drainage......................... 87 Technical data ...................... 88 Settings menu ...................... 89 Opening the Settings menu ................... 89 Language ......................
Guide to the appliance Appliance overview a Upper spray arm (not visible) g Filter combination b Cutlery tray (depending on model) h Data plate c Upper basket i Rinse aid reservoir d Middle spray arm j Dual compartment detergent dis‐ penser e Air inlet for drying (depending on model)
Guide to the appliance Control panel a Programme selection f OK button b Display g button (FlexiTimer) with indicator light c Option buttons with indicator lights h Programme selector button d Start button with indicator light i On/Off button e Arrow buttons ...
Guide to the appliance Display Settings menu General The display is used to select or set the following: – the programme – the FlexiTimer (Delay start) – the Settings menu The Settings menu is used to alter the dishwasher's electronics to suit differ‐ The display can show the following: ent requirements.
Keep the installation plan and the operating instructions in a safe place and pass them on to any future owner. Miele cannot be held liable for damage caused by non-compli‐ ance with this information.
Page 10
Warning and Safety instructions Correct application This appliance is designed for domestic use and for use in similar environments by guests in hotel or motel rooms, bed & breakfasts and other typical living quarters. This does not include common/ shared facilities or commercial facilities within hotels, motels or bed &...
Page 11
Warning and Safety instructions Safety with children Young children must not be allowed to use this appliance. Older children may only use the appliance when its operation has been clearly explained to them and they are able to use it safely, rec‐ ognising the dangers of misuse.
Page 12
Repairs and other work by unqualified persons could be danger‐ ous. Installation, maintenance work and repairs to electrical applian‐ ces must only be carried out by a Miele approved service technician. Before installation, check the dishwasher for visible signs of dam‐...
Page 13
Warning and Safety instructions To avoid the risk of damage to the dishwasher, make sure that the connection data on the data plate (fuse rating, voltage and frequen‐ cy) matches the mains electricity supply before connecting the dish‐ washer to the mains. Consult a qualified electrician if in any doubt. ...
Page 14
If the connection cable is damaged, it must be replaced with a special cable of the same type (available from Miele) by a Miele au‐ thorised service technician only in order to avoid a hazard.
Page 15
Warning and Safety instructions In areas which may be subject to infestation by cockroaches or other vermin, pay particular attention to keeping the appliance and its surroundings in a clean condition at all times. Any damage which may be caused by cockroaches or other vermin will not be covered by the warranty.
Warning and Safety instructions Correct use Do not use solvents in the dishwasher. Danger of explosion! Do not inhale or ingest dishwasher detergent. Some dishwasher detergents are strongly alkaline and contain irritants or corrosive in‐ gredients. They can be extremely dangerous if swallowed, and can cause burning in the nose, mouth and throat, or inhibit breathing.
Page 17
Accessories Use only genuine original Miele spare parts. If spare parts or ac‐ cessories from other manufacturers are used, the warranty will be in‐ validated, and Miele cannot accept liability. Disposal of your old dishwasher ...
Caring for the environment Disposal of the packing mate‐ Disposing of your old appli‐ rial ance The packaging is designed to protect Electrical and electronic appliances of‐ the appliance from damage during ten contain materials which, if handled transportation. The packaging materials or disposed of incorrectly, could be po‐...
– Follow the detergent manufacturer's recommendations on detergent dos‐ age. – When using powder or liquid deter‐ gent you can use less detergent if baskets are only half full. You can find further tips on energy- saving dishwashing in "Miele's guide to dishwashing".
Caring for the environment EcoFeedback consumption in‐ 2. Actual consumption dicator At the end of the programme you can call up the actual amount of energy and function is used for Consumption water used by the programme which calling up information about the energy has just been run.
Before using for the first time Opening the door Closing the door At the end of programmes with a drying Push the baskets right in. phase (see "Programme chart"), the Then lift the door upwards and push door will open automatically a little in until it clicks into position.
Before using for the first time Basic settings Time of day The display will then change to the Switch the dishwasher on with the screen for setting the time. button. The time of day needs to be set before The welcome screen will appear when the "FlexiTimer"...
Page 23
Before using for the first time Water hardness The message will then ap‐ Set up finished pear in the display. The display will then change to the screen for setting the water hardness. After confirming this with OK, the prompts and ...
Before using for the first time Before using the appliance for If the water hardness in your area is the first time, you require: constantly lower than 0.9 mmol/l (5 °d), you do not need to add dish‐ – approx. 2 litres of water, washer salt.
Before using for the first time Filling the salt reservoir Before filling the salt reservoir with dishwasher salt for the first time, you must fill it with approx. 2 litres of wa‐ ter to enable the salt to dissolve. Once the dishwasher has been used, there is always sufficient water in the reservoir.
Before using for the first time Add salt reminder If you only ever use multi-function combination products in your dish‐ Fill the salt reservoir with dishwasher washer, you can switch off both refill salt for reactivation when Add salt reminders for salt and rinse aid if you appears in the display (If it appears wish (see "Settings menu - Switching...
Before using for the first time Rinse aid If you only ever use combination products containing rinse aid in your Rinse aid is necessary to ensure water dishwasher, you do not need to add does not cling and leave marks on rinse aid.
Before using for the first time Add rinse aid reminder When the message ap‐ Add rinse aid pears in the display, the reservoir con‐ tains sufficient rinse aid for 2 - 3 pro‐ grammes only. Add rinse aid in plenty of time. ...
Loading the dishwasher Notes – The spray arms must not be blocked by items which are too tall or hang Remove coarse food residues from through the baskets. If in doubt, test crockery. for free movement by manually rotat‐ ing the spray arms. There is no need to rinse items under running water.
Page 30
– Use detergents with glass protective ted at the end of a programme, where additives (e.g. Miele CareCollection water has not run off smoothly. It may tabs). need to be rubbed dry with a soft cloth.
Loading the dishwasher Upper basket Cup rack To make room for tall items, raise the See "Loading the dishwasher / Load‐ rack upwards. ing examples" for examples of how to Glasses can be arranged along the po‐ load crockery and cutlery. sitioning rail of the cup rack to give them some support during the pro‐...
Loading the dishwasher Adjusting the upper basket Depending on the setting of the upper basket, the following plate dimensions In order to gain more space for taller can be accommodated. pieces of crockery in the bottom or up‐ per basket, the upper basket can be Dishwashers with cutlery basket adjusted on three levels with 2 cm be‐...
Loading the dishwasher Lower basket MultiComfort area The rear section of the lower basket is See "Loading the dishwasher / Load‐ used for washing cups, glasses, plates, ing examples" for examples of how to pots and pans. load crockery and cutlery. ...
Page 34
Loading the dishwasher Hinged spikes (depending on model) The spikes at the front are used for washing plates, soup bowls, platters, dessert bowls and saucers. Both rows of spikes can be lowered to make more room for large items, e.g. pots, pans and dishes.
Loading the dishwasher Cutlery 3D cutlery tray (depending on model) See "Loading the dishwasher / Load‐ ing examples" for examples of how to load crockery and cutlery. Arrange the cutlery in the tray as shown. To make unloading much easier, cutlery should be grouped in zones, one for knives, one for forks, one for spoons, etc.
Loading the dishwasher Cutlery basket (depending on model) Fit it onto the cutlery basket if re‐ quired. The cutlery basket can be placed any‐ where on the front rows of spikes in the lower basket. To avoid the risk of injury, knives and forks should be placed with the han‐...
Comparison tests Standard height with cutlery tray Test standard: AS/NZS 2007.1:2005, AS/NZS 2007.2:2005; AS/NZS 6400:2005 Standard programme for en‐ ergy label comparison tests: Capacity: 14 place settings Detergent quantity: 32.5 g in compartment II Rinse aid dispensing: Setting 3 You can find information on adjusting the rinse aid dosage in the "Rinse aid"...
Comparison tests XXL height with cutlery tray Test standard: AS/NZS 2007.1:2005, AS/NZS 2007.2:2005; AS/NZS 6400:2005 Standard programme for en‐ ergy label comparison tests: Capacity: 15 place settings Detergent quantity: 33.7 g in compartment II Rinse aid dispensing: Setting 3 You can find information on adjusting the rinse aid dosage in the "Rinse aid"...
For optimum cleaning and drying re‐ remove coloured stains (e.g. tea, cof‐ sults, use Miele dishwasher detergent fee, tomato sauce). and add Miele salt and Miele rinse aid separately. See "Optional accesso‐ Most dishwasher detergents are mildly ries". alkaline and contain enzymes and oxy‐...
Page 48
Operation Detergent dosage Some dishwasher detergents are Follow the dosage recommended by strongly alkaline and contain irritant the manufacturer on the packaging. or corrosive ingredients which can cause burning in the nose, mouth Unless directed otherwise, use one and throat if swallowed, or inhibit detergent tab or add 20 to 30 ml de‐...
Operation Adding detergent Add the required amount of detergent and close the flap. Press the opening catch on the de‐ tergent dispenser. The flap will spring Make sure that the detergent packag‐ open. ing is properly closed after use to avoid it getting damp and becoming The flap is always open at the end of a lumpy.
Operation Switching on Selecting a programme Make sure the spray arms are not ob‐ Choose your programme according to structed. the type of load and how dirty it is. Close the door. The different programmes and their uses are described in the Programme ...
Operation Starting the programme Display Press the Start or OK button. The estimated duration of the pro‐ gramme selected appears in hours and The programme will begin. minutes in the display before the pro‐ The Start indicator light will come on. gramme begins.
Operation Energy management At the end of the programme To save energy, the dishwasher will The programme has finished when switch off automatically a few minutes appears in the display and the Finished after the last time a button has been door has opened slightly (if applicable).
Operation Switching off Unloading the dishwasher At the end of a programme: Dishes tend to break and chip more easily when they are hot. Allow the The dishwasher can be switched off dishes to cool until they are comforta‐ at any time using the ...
Operation Interrupting a programme Changing a programme A programme is interrupted as soon as If the detergent dispenser flap has the door is opened. already opened, do not change the If the door is closed again, the pro‐ programme. gramme will continue from the point it was at before the door was opened.
Programme options Options Short The Short option reduces the duration You can select and deselect the options of programmes in which this option is using the appropriate buttons and the available by up to 30%. display. In order to achieve optimum cleaning ...
Programme options FlexiTimer with EcoStart Switch the dishwasher on with the button. The FlexiTimer gives you three ways The Start indicator light will flash. of starting the programme by means of delaying the start. You can set the start ...
Page 57
Programme options Start at Finish at With the function, you set the With the function, you set the Start at Finish at exact time at which you want the pro‐ time at which you wish the programme gramme to start. to end.
Page 58
Programme options EcoStart Changing or deleting set times function allows you to take You can change the set times or the EcoStart advantage of time variable economy programme before the start time in the rates of electricity. Before you can use display is reached.
Programme options DetergentAgent For optimum cleaning results, the dish‐ washer automatically adjusts the pro‐ gramme sequence to the type of deter‐ gent being used. Depending on the programme, this can mean that the run‐ ning time and energy consumption vary slightly.
Programme chart Programme Programme sequence Pre-wash Main wash Interim rinse Final rinse Drying °C °C Sensor wash Variable programme sequence, sensor-controlled adjustment according to amount of crockery and soiling 47-65 required required Light soiling 55°C Intensive 75°C Sensor wash gentle Quick wash 40°C ExtraQuiet...
Page 61
Programme chart Consumption Duration Electricity Water Cold water Hot water Litres Cold water Hot water h:min h:min 2:41 2:34 0.73 / 0.76 0.40 / 0.44 11.3 / 11.0 1:25-2:45 1:20-2:35 0.70 -1.30 0.50 -0.85 -16.0 1.10 0.70 14.0 1:59 1:47 1.45 0.95 15.0...
Page 62
Programme chart Crockery Food deposits Action required Variable, sensor-controlled Mixed, All fresh to dried-on programme sequence everyday crockery food deposits Shorter duration Heat-sensitive glasses and plastic This needs a gentle Fresh, easily removed food programme with glass care deposits Shorter duration Mixed crockery This needs a water and energy saving programme...
Page 63
Programme chart Programme Detergent Compartment I Compartment II 25 ml Sensor wash 1 tab +short 20 ml Sensor wash gentle 1 tab +short 25 ml 1 tab 25 ml Light soiling 55°C 1 tab +short 25 ml Intensive 75°C 10 ml 1 tab +short...
Cleaning and care Cleaning the door and the door Check your dishwasher regularly (ap‐ seal prox. every 4-6 months). This way faults and problems can be avoided. Mould could build up on the door seal and the sides of the dishwasher door ...
– dishwasher cleaner, For cleaning, you can also use a clean, damp microfibre cloth, such as – oven cleaner, the Original Miele all purpose microfi‐ – glass cleaning agents, bre cloth, without any cleaning agent. – hard, abrasive brushes or sponges, e.g.
Cleaning and care Checking the filters in the Cleaning the filters wash cabinet Switch the dishwasher off. The filter combination in the base of the wash cabinet retains coarse soil from the suds solution, preventing it access‐ ing the circulation system and re-enter‐ ing the cabinet through the spray arms.
Page 68
Cleaning and care To clean the inside of the filter, the flap Replace the filter combination so that it lies flat in the base of the wash must be opened: cabinet. Press the catches together in the ...
Cleaning and care Cleaning the spray arms Particles of food can get stuck in the spray arm jets and bearings. The spray arms should therefore be inspected and cleaned regularly (approx. every 4 - 6 months). Switch the dishwasher off. Remove the spray arms as follows: ...
Reset or replace the fuse (see data plate for mini‐ mum fuse rating). If the mains fuse trips again, call Miele. The Start indicator light The appliance is not plugged in. does not flash after the ...
Page 71
Switch the dishwasher back on. Select the programme you want. Press the Start button. If the fault message appears again, there is a techni‐ cal fault. Call Miele. The Waterproof system has reacted. Waterproof Turn off the tap.
Problem solving guide Water inlet fault Problem Possible cause and remedy One of the following messages appears in the display: The tap is turned off. Open stopcock Turn on the tap fully. Before rectifying the problem, you must: ...
Problem solving guide Water drainage fault Problem Possible cause and remedy The following fault mes‐ Before rectifying the problem, you must: sage appears in the dis‐ Switch the dishwasher off with the button. play: The water outlet is restricted. ...
Problem solving guide General problems Problem Possible cause and remedy The indicator lights and The display has switched off automatically to save display are dark. energy. Switch the dishwasher on again with the but‐ ton. Detergent residue is left The dispenser was still damp when detergent was in the dispenser at the added.
Problem solving guide Noises Problem Possible cause and remedy Knocking noise in the A spray arm is knocking against an item in a basket. wash cabinet. Interrupt the programme, and rearrange the items which are obstructing the spray arm. Rattling noise in the Items of crockery are insecure in the wash cabinet.
Problem solving guide Unsatisfactory washing result Problem Possible cause and remedy The dishes are not The dishes were not loaded correctly. clean. See notes in "Loading the dishwasher". The programme was not powerful enough. Select a more intensive programme (see "Pro‐ gramme chart").
Page 77
Problem solving guide Problem Possible cause and remedy Dishes, cutlery and The amount of rinse aid may be insufficient, or the glasses are not dry or rinse aid reservoir is empty. are flecked. Replenish the reservoir, increase the dosage or change the brand of rinse aid (see "Before using for the first time - Rinse aid").
Page 78
Problem solving guide Problem Possible cause and remedy White residue is visible Not enough rinse aid was used. on cutlery and crock‐ Increase the dosage (see "Settings menu - Rinse ery, clouding occurs on aid"). glassware; film can be There is no salt in the salt reservoir.
Replace the filter and washer, making water inlet hose threaded union. This sure they are sitting correctly. filter is available from Miele. Reconnect the inlet hose to the tap, Cleaning the filter: making sure it goes on correctly and ...
Maintenance Cleaning the drain pump and non-return valve If the water has not been pumped away at the end of a programme, the drain pump or the non-return valve might be blocked. They are, however, easy to clean. Disconnect the dishwasher from the mains supply.
2 years. Miele. For further information, please refer to your warranty booklet. The contact details for Miele are giv‐ en at the back of these instructions. When contacting Miele, please quote the model and serial number of your...
– phosphate-free - safe for the environ‐ www.miele-shop.com (depending on ment country) or from Miele (see end of this booklet for contact details). – water-soluble wrapping - no need to unwrap Powder detergent –...
Page 83
Optional accessories Dishwasher care products Accessories Miele cleaning and care products pro‐ Some accessories may be supplied as vide optimum care for your dishwasher. standard, depending on model. Dishwasher cleaner Cappuccinatore insert – cleans the dishwasher effectively and The Cappuccinatore insert can be used...
Electrical connection This dishwasher is supplied with a Before connecting the appliance, mains cable with moulded plug ready check that the connection data on for connection to an AC single phase the data plate (voltage, frequency, supply, (230 - 240 V 50 Hz for NZ and rated load and fuse rating) matches Australia) via a suitable switched sock‐...
Water connection The Miele Waterproof system Connection to the water sup‐ As long as your dishwasher has been installed correctly, the Miele waterproof Water in the dishwasher must anti-leak system will protect you from not be used as drinking water.
Page 86
Water connection – A tap with a 3/4 " male thread must After connecting the dishwasher to be provided on site. the water supply, check that all plumbing connections are watertight. – Connection to the mains water sup‐ ply should only be carried out by a ...
Water connection Drainage Venting the drainage system If the on-site drain connection is situ‐ – The appliance drainage system is fit‐ ated lower than the guide path for the ted with a non-return valve which bottom basket rollers in the open door, prevents dirty water from flowing the drainage system must be vented.
Technical data Dishwasher model Standard Height freestanding model 84.5 cm (adjustable + 3.5 cm) Height built-in model 80.5 cm (adjustable 84.5 cm (adjustable + 6.5 cm) + 6.5 cm) Height of building-in recess Min. 80.5 cm (+ 6.5 Min. 84.5 cm (+ 6.5 Width 59.8 cm 59.8 cm...
Settings menu Settings menu for changing Language standard settings The display can be set to appear in one of several different languages. Opening the Settings menu You can change the language in the Switch the dishwasher off with the display via the sub-menu.
Settings menu Time of day Setting the clock format You can select either a 24-hour or 12- The dishwasher is delivered with the hour clock. time of day (clock) display deactivated. Select the option. Clock format To save energy, the dishwasher will switch off automatically a few minutes ...
Settings menu Water hardness °d mmol/l °f Display This appliance is fitted with a water softener. – The dishwasher must be program‐ med for the water hardness in your area. – Your local water authority will be able to advise you of the water hardness level in your area.
Settings menu Rinse aid Consumption (EcoFeedback) You can adjust the rinse aid dosage for You can programme the dishwasher so best results. that the energy and water consumption The rinse aid dosage can be set from of the currently selected programme approx.
Settings menu EcoStart Setting the electricity tariff times Before you can use the option, EcoStart In order to run your dishwasher in the you must set at least one electricity tar‐ most economical way, you can use the iff time. option to take advantage of EcoStart your electricity supplier's time variable...
Page 94
Settings menu Changing the electricity tariff times Deleting the electricity tariff times You can change the start, finish or pri‐ You can delete the settings for an ority of an electricity tariff time. electricity tariff time and in doing so deactivate the option for this EcoStart...
Settings menu Sensor wash Switching off the refill remind‐ You can adjust the Sensor wash pro‐ gramme so that it will remove stubborn If you only ever use multi-function com‐ soiling in a lightly soiled load. bination products containing salt and rinse aid in your dishwasher, you can ...
Settings menu Check filters Pre-wash You can adjust the interval at which the You can use this function to remove message to remind you to check the fil‐ easily loosened food residues in the ters appears. programme selected. You can set an interval of between 30 Once activated, this function will be and 60 programme cycles.
Settings menu Version info Factory default settings You can call up the electronic software You can reset all settings to the factory version of your dishwasher for technical default settings. support purposes. Select and confirm with OK. Reset Confirm the display with OK. Closing the Settings menu Showroom programme You can exit the Settings menu using...
Page 99
Miele Australia Pty. Ltd. ACN 005 635 398 ABN 96 005 635 398 Miele Center and Head Office Melbourne: 1 Gilbert Park Drive Knoxfield, VIC 3180 Miele Center and Office Melbourne: 206-210 Coventry Street South Melbourne, VIC 3205 Miele Center and Office Sydney:...
Page 100
G 6300 / G 6305 en-AU, NZ M.-Nr. 09 867 840 / 04...