Advertisement
Quick Links
Thank you for purchasing a Sealey product. Manufactured to a high standard this product will give you years of trouble free performance
if these instructions are carefully followed and the product is correctly maintained.
IMPORTANT: pleAse ReAD THese INsTRUCTIONs CAReFUlly. NOTe THe sAFe OpeRATIONAl ReQUIRemeNTs,
WARNINGs AND CAUTIONs. Use THIs pRODUCT CORReCTly AND WITH CARe FOR THe pURpOse FOR WHICH IT Is
INTeNDeD. FAIlURe TO DO sO mAy CAUse DAmAGe OR peRsONAl INJURy AND WIll INVAlIDATe THe WARRANTy.
pleAse ReTAIN THese INsTRUCTIONs FOR FUTURe Use.
1. sAFeTy INsTRUCTIONs
WARNING! Ensure health & safety, local authority, and general workshop practice regulations are strictly adhered to when using this
equipment.
Familiarise yourself with product application and limitations, as well as the specific potential hazards peculiar to this product.
Maintain the pump station in good condition (use an authorised service agent).
Replace or repair damaged parts. Use genuine parts only. Non authorised parts will invalidate the warranty.
Use only to pump lubricants up to SAE 150 viscosity, used oil and antifreeze liquids.
Ensure safety eye protection, oil resistant gloves and protective clothing are worn when using this product.
Keep the work area clean, uncluttered and ensure there is adequate lighting.
Maintain correct balance and footing. Ensure the floor is not slippery and wear non slip shoes.
Keep children and unauthorised persons away from the working area.
After use, drain any fluids from the equipment before storage.
Dispose of waste liquids in accordance with local authority regulations.
Disconnect air pressure from equipment when not in use.
DO NOT exceed the maximum air pressure of 115psi.
DO NOT point the nozzle at people or animals.
DO NOT use the equipment near open flames.
DO NOT smoke whilst using this equipment.
DO NOT use to extract corrosive fluids.
DO NOT dismantle, tamper with or adapt the pump for any purpose other than for which it is designed.
DO NOT use the unit if it has been dropped or mishandled, check the unit to ensure there is no damage.
DO NOT leave the trolley on a slope, or traverse slopes, which may cause the unit to topple.
The unit must be stored on a level surface.
Keep the pump clean and store in a safe dry, childproof location.
WARNING! DO NOT allow uncontrolled discharge of fluids thus polluting the environment. All liquids must be disposed of according to
local authority regulations.
2. INTRODUCTION
Mobile oil dispensing unit with air operated 3:1 double acting pump for barrel or
tanks with 2"BSP fittings. Pump is supplied with air management system and
connected to a 730mm rigid suction probe with non-return valve. Features 4mtr
hose and digital oil meter Model no. AK4565D. Suitable for use with engine,
hydraulic, synthetic, gear and transmission oils up to SAE150.
Model:
Pump Ratio:
Maximum Flow Rate:
Maximum Viscosity:
Maximum output Pressure:
Maximum Air Pressure:
Recommended Air Pressure:
outlet:
Digital Hose End Meter
Model:
Accuracy:
Inlet:
Battery:
AK4563D
3:1
12ltr/min
150SAE
350psi
115psi
70psi
1/2"BSP
AK4565D
+/- 0.5%
1/2"BSP
Lithium cR2 3V 1400mAH
InSTRUcTIonS FoR:
OIl DIspeNsING
sysTem AIR OpeRATeD
AK4563D
Model no:
AK4563D
Issue no: 1 - 14/11/08
Advertisement
Related Manuals for Sealey AK4563D
Summary of Contents for Sealey AK4563D
- Page 1 AK4563D Model no: Thank you for purchasing a Sealey product. Manufactured to a high standard this product will give you years of trouble free performance if these instructions are carefully followed and the product is correctly maintained. IMPORTANT: pleAse ReAD THese INsTRUCTIONs CAReFUlly. NOTe THe sAFe OpeRATIONAl ReQUIRemeNTs, WARNINGs AND CAUTIONs.
- Page 2 Slide the locking nut, locking ring and the barrel nut onto the pick up probe of the pump (fig.3), screw the locking nut onto the barrel nut to lock the assembly to the pick up probe. Lock Ring 3.2.6 Insert the pump assembly into the support brackets on the trolley and hang the meter onto the accesssory support bracket. Barrel Nut fig.3 AK4563D Issue no: 1 - 14/11/08...
- Page 3 Press button "2" on the rear of the meter for 1 sec to enter the correction Factor mode. 4.7.2 Press the Move button five times to select the units (fig.5.3). 4.7.3 Press the Reset button to scroll through the Units (L/Gal/PT/QT), select the Unit required. 4.7.4 Press "2" for 1 sec to quit the correction Factor mode. fig.7 AK4563D Issue no: 1 - 14/11/08...
- Page 4 Signed by Steve Buckle Air Operated Model: AK4563D For Jack Sealey Ltd. Sole importer into the UK of Sealey Power Products. 2002/95/Ec RoHS Directive 2002/96/EEc WEEE Directive The construction file for this product is held by the Manufacturer and may be inspected on request by contacting Jack Sealey Ltd.