free stats
Download Print this page
Sealey AK4560D Instructions

Sealey AK4560D Instructions

Oil dispensing pump station air operated

Advertisement

Quick Links

thank you for purchasing a Sealey product. Manufactured to a high standard this product will give you years of trouble free performance
if these instructions are carefully followed and the product is correctly maintained.
IMPORTANT: pleAse ReAD THese INsTRuCTIONs CAReFullY. NOTe THe sAFe OpeRATIONAl ReQuIRemeNTs,
WARNINGs AND CAuTIONs. use THIs pRODuCT CORReCTlY AND WITH CARe FOR THe puRpOse FOR WHICH IT Is
INTeNDeD. FAIluRe TO DO sO mAY CAuse DAmAGe OR peRsONAl INJuRY AND WIll INVAlIDATe THe WARRANTY.
pleAse ReTAIN THese INsTRuCTIONs FOR FuTuRe use.
1. sAFeTY INsTRuCTIONs
WARNING! Ensure health & safety, local authority, and general workshop practice regulations are strictly adhered to when using this
equipment.
Familiarise yourself with product application and limitations, as well as the specific potential hazards peculiar to this product.
Maintain the pump station in good condition (use an authorised service agent).
Replace or repair damaged parts. Use genuine parts only. Non authorised parts will invalidate the warranty.
Use only to pump lubricants up to SAE 150 viscosity and antifreeze liquids.
Ensure safety eye protection, oil resistant gloves and protective clothing are worn when using this product.
Keep the work area clean, uncluttered and ensure there is adequate lighting.
Maintain correct balance and footing. Ensure the floor is not slippery and wear non slip shoes.
Keep children and unauthorised persons away from the working area.
After use, drain any fluids from the equipment before storage.
Dispose of waste liquids in accordance with local authority regulations.
Disconnect air pressure from equipment when not in use.
DO NOT exceed the maximum air pressure of 115psi.
DO NOT point the nozzle at people or animals.
DO NOT use the equipment near open flames.
DO NOT smoke whilst using this equipment.
DO NOT use to extract corrosive fluids.
DO NOT dismantle, tamper with or adapt the pump for any purpose other than for which it is designed.
DO NOT use the unit if it has been dropped or mishandled, check the unit to ensure there is no damage.
Keep the pump clean and store in a safe dry, childproof location.
WARNING! DO NOT allow uncontrolled discharge of fluids thus polluting the environment.
All liquids must be disposed of according to local authority regulations.
2. INTRODuCTION
Air operated 3:1 double acting pump for barrel or tanks with 2"BSP fittings. Pump
is supplied with air management system and connected to a 940mm rigid suction
probe with non-return valve. Features hose for attachment to digital oil meter or to
optional retractable hose reel. Suitable for use with engine, hydraulic, synthetic,
gear and transmission oils up to SAE150.
Model:
Pump Ratio:
Maximum Flow Rate:
Maximum Viscosity:
Maximum output Pressure:
Maximum Air Pressure:
Recommended Air Pressure:
outlet:
Digital Hose End Meter
Model:
Accuracy:
Inlet:
Battery:
AK4560D
3:1
12ltr/min
150SAE
350psi
115psi
70psi
1/2"BSP
AK4565D
+/- 0.5%
1/2"BSP
Lithium cR2 3V 1400mAH
InStRUctIonS FoR:
OIl DIspeNsING pump
sTATION AIR OpeRATeD
AK4560D
Model no:
AK4560D
Issue no: 1 - 05/11/08

Advertisement

loading

Summary of Contents for Sealey AK4560D

  • Page 1 AK4560D Model no: thank you for purchasing a Sealey product. Manufactured to a high standard this product will give you years of trouble free performance if these instructions are carefully followed and the product is correctly maintained. IMPORTANT: pleAse ReAD THese INsTRuCTIONs CAReFullY. NOTe THe sAFe OpeRATIONAl ReQuIRemeNTs, WARNINGs AND CAuTIONs.
  • Page 2 Press the Reset button to add 1 on the digit, press as many times as required until the correct number is reached. 4.5.5 Press "2" for 1 sec to quit the correction Factor mode. 4.5.6 Press the Move + Reset buttons simultaneously to display the new correction fig.4 factor. AK4560D Issue no: 1 - 05/11/08...
  • Page 3 5th november 2008 Air Operated Model: AK4560D For Jack Sealey Ltd. Sole importer into the UK of Sealey Power Products. 2002/95/Ec RoHS Directive 2002/96/EEc WEEE Directive the construction file for this product is held by the Manufacturer and may be inspected on request by contacting Jack Sealey Ltd.