Advertisement
Quick Links
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to
Wear eye
instructions
protection
1. SAFETY
WARNING! Ensure Health & Safety, local authority and general workshop practice regulations are adhered to when using this equipment.
‰
WARNING! Disconnect the hammer from the air supply before changing accessories, servicing or performing any maintenance.
‰
Keep the hammer clean and maintain it in good condition.
9
Replace or repair damaged parts. Use genuine parts only. Unauthorised parts may be dangerous and will invalidate the warranty (use an
9
authorised service agent).
Keep the work area clean and uncluttered. Ensure that there is adequate lighting.
9
Ensure chisels are correctly rated for the job. DO NOT use damaged or suspect chisels.
9
WARNING! Wear approved safety eye or face protection, ear defenders and, if dust is generated, respiratory protection.
‰
Keep hands and body clear of the work when operating the hammer.
9
Maintain correct balance and footing. Ensure that the floor is not slippery and wear non-slip shoes.
9
Remove ill fitting clothing. Remove ties, watches, rings and other loose jewellery and contain and/or tie back long hair.
9
Keep children and unauthorised persons away from the work area.
9
Secure unstable workpiece with a clamp, vice or other adequate holding device.
9
Avoid unintentional starting.
9
WARNING! Ensure that the correct air pressure is maintained and not exceeded.
‰
Keep air hose away from heat, oil and sharp edges. Check air hose for wear before each use and ensure that all connections are secure.
9
DO NOT use the hammer for a task it is not designed to perform.
8
DO NOT operate the hammer if any parts are damaged or missing as this may cause failure and/or personal injury.
8
WARNING! DO NOT chisel into any materials containing asbestos.
‰
DO NOT switch the hammer on whilst the chisel is in contact with the workpiece.
8
DO NOT carry by the hose, or yank the hose from the air supply.
8
DO NOT hold the workpiece by hand. Use clamps or a vice (not included) to secure the workpiece. Available from your Sealey stockist.
8
DO NOT allow untrained persons to operate the hammer.
8
DO NOT operate the hammer when you are tired or under the influence of alcohol, drugs or intoxicating medication.
8
DO NOT use hammer where there is flammable liquid, solid or gas such as paint solvent, including waste wiping or cleaning rags etc.
8
DO NOT leave the hammer operating unattended.
8
DO NOT carry the hammer with your finger on the trigger.
8
DO NOT direct air from the air hose at yourself or others.
8
When work is complete ensure that the air supply is turned off.
9
When not in use disconnect from the air supply and store in a safe, dry, childproof area.
9
2.
INTRODUCTION
I
Generation Series air hammer kit. Handle exhaust reduces noise emission, and contoured soft grip allows added comfort and control. Chisel variety
covers a range of different job applications. Supplied in storage case.
3. SPECIFICATION
Model no ............................................................... GSA12.V2
Air consumption ............................................................. 4cfm
Chisel shank size .......................................401" Parker Taper
Free speed .............................................................. 4500bpm
Stroke .......................................................................... 43mm
Inlet size ....................................................................1/4"BSP
Operating pressure ....................................................... 90psi
Noise power/pressure .......................................... 94/84dB(A)
Vibration/uncertainty .............................................. 27/10.8m²
© Jack Sealey Limited
MEDIUM STROKE AIR HAMMER KIT
GSA12.V2
MODEL NO:
Wear protective
Wear a mask
gloves
Original Language Version
Wear ear
protection
GSA12.V2 Issue:1 23/12/20
Advertisement
Related Manuals for Sealey GSA12.V2
Summary of Contents for Sealey GSA12.V2
- Page 1 DO NOT carry by the hose, or yank the hose from the air supply. DO NOT hold the workpiece by hand. Use clamps or a vice (not included) to secure the workpiece. Available from your Sealey stockist. DO NOT allow untrained persons to operate the hammer.
- Page 2 6.1. Keep the hammer oiled for optimum performance. Lubricate with a good grade of air tool oil such as Sealey ATO/500 or ATO/1000. If there is no oiler in the air system then a teaspoon of oil can be poured into the air inlet of the hammer, or into the hose at the nearest connection to the air supply.