Advertisement
Quick Links
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to
Wear protective
instruction
gloves
manual
1. SAFETY
Follow all workshop health & safety rules, regulations, and conditions when using drill.
9
WARNING! Disconnect from air supply before changing accessories or servicing.
‰
WARNING! Check correct air pressure is maintained and not exceeded. We recommended 90 psi.
‰
Maintain the drill in good condition and replace any damaged or worn parts. Use genuine parts only. Non-authorised parts may be
9
dangerous and will invalidate the warranty.
Keep air hose away from heat, oil and sharp edges. Check air hose for wear before each use and ensure that all connections are secure.
9
Wear approved safety eye protection. If dust is generated wear respiratory protection, and safety gloves.
9
Wear suitable clothing to avoid snagging. DO NOT wear loose jewellery and tie back long hair.
9
Keep hands away from rotating chuck and drill bit.
9
Keep drill bits clean and sharp for best and safest performance.
9
Maintain correct balance and footing. Ensure the floor is not slippery and wear non-slip shoes.
9
Secure non stable work piece with a clamp, vice or other adequate holding device.
9
Ensure the chuck is securely fastened to the spindle and the drill bit is secure in the chuck.
9
Keep children and unauthorised persons away from the working area.
9
WARNING! DO NOT use drill if damaged or faulty. Contact your local service agent.
‰
WARNING! Beware of high-reaction torque when breaking through the material being drilled.
‰
DO NOT get the drill wet or use in damp or wet locations.
8
DO NOT apply excessive loads to the drill bit during operation.
8
DO NOT hold the workpiece by hand. Use clamps or a vice to secure the workpiece.
8
DO NOT use the drill for a task it is not designed to perform.
8
DO NOT use drill unless you have been instructed in its use by a qualified person.
8
DO NOT drop, throw or abuse the drill.
8
DO NOT carry the drill by the air hose, or yank the hose from the air supply.
8
DO NOT operate drill if you are tired, under the influence of alcohol, drugs or intoxicating medication.
8
DO NOT carry drill with your hand on the power trigger in order to avoid unintentional starting.
8
DO NOT direct air from the air hose at yourself or others.
8
When not in use disconnect from air supply and store in a safe, dry, childproof location.
9
2.
INTRODUCTION
i
Powder coated aluminium housing for added corrosion resistance, with planetary gear drive assembly. Features reversible action making
this tool suitable for driving fixings. Fitted with 10mm drill chuck and supplied with chuck key. Suitable for the DIY enthusiast and light
garage use. Air Supply: 90psi - 4cfm. Model No. S01047
3.
SPECIFICATION
si4
Model No. .................................................................... S01047
Free Speed: ............................................................. 1800rpm
Chuck size ................................................................ Ø10mm
Air Consumption: ........................................................... 4cfm
Operating Pressure: ...................................................... 90psi
Air inlet Size: .............................................................1/4"BSP
Weight: ........................................................................ 1.15kg
Noise Power/Pressure: ...................................... 101/90dB(A)
Vibration/Uncertainty: ......................................... 0.89/1.5m/s
4.
PREPARATION
si4
4.1.
Air Supply
WARNING! Ensure the air supply is clean and does not exceed 90psi while operating the drill. Too high an air pressure and unclean air
‰
will shorten the product life due to excessive wear, and may be dangerous causing damage and/or personal injury.
4.1.1.
Ensure drill air valve (or trigger) is in the "off" position before connecting to the air supply.
4.1.2.
You will require an air pressure of 90psi, and an air flow according to specification.
4.1.3.
Drain the air tank daily. Water in the air line will damage the drill.
© Jack Sealey Limited
AIR DRILL 10MM 1800RPM REVERSIBLE
MODEL NO:
Wear eye
Wear face
protection
mask
Chuck Size:
10mm
Chuck Size:
10mm
S01047
Wear ear
protection
2
Original Language Version
S010147
Issue 2 (H, F) 09/05/18
Advertisement
Related Manuals for Sealey Siegen Tools S01047
Summary of Contents for Sealey Siegen Tools S01047
- Page 1 S01047 MODEL NO: Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions, and properly maintained, give you years of trouble free performance. IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED.
- Page 2 Vibration may cause failure if a quick change coupling is connected directly to the drill. To overcome this, connect a leader hose to the drill (Sealey ref: AH2R or AH2R/38). A quick change coupling may then be used to connect the leader hose to the air line recoil hose.
- Page 3 Use genuine parts only. Non-authorised parts may be dangerous and will invalidate the warranty. 6.1. Lubricate the air drill daily with a few drops of Sealey air tool oil dripped into the air inlet to prolong its life. 6.2.
- Page 4 Important: No Liability is accepted for incorrect use of this product. Warranty: Guarantee is 12 months from purchase date, proof of which is required for any claim. Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR 01284 757500 01284 703534 sales@sealey.co.uk...