All the information in this manual is intended only for trained Service Providers who are familiar with Lenovo® computer products. Before using this information and the product it supports, be sure to read and understand the Chapter 2 “Safety information” on page 3 and Appendix A “Notices” on page 207.
Page 8
Lenovo plans to transition to RoHS compliance well before the implementation date and expects its suppliers to be ready to support Lenovo's requirements and schedule in the EU. Products sold in 2005, will contain some RoHS compliant FRUs. The following statement pertains to these products and any product Lenovo produces containing RoHS compliant parts.
Page 10
Important: Use only approved tools and test equipment. Some hand tools have handles covered with a soft material that does not insulate you when working with live electrical currents. Many customers have, near their equipment, rubber floor mats that contain small conductive fibers to decrease electrostatic discharges. Do not use this type of mat to protect yourself from electrical shock.
Voltage-selection switch Some computers are equipped with a voltage-selection switch located near the power-cord connection point on the computer. If your computer has a voltage-selection switch, ensure that you set the switch to match the voltage available at your electrical outlet. Setting the voltage-selection switch incorrectly can cause permanent damage to the computer.
5. Check for any obvious alterations. Use good judgment as to the safety of any alterations. 6. Check inside the unit for any obvious unsafe conditions, such as metal filings, contamination, water or other liquids, or signs of fire or smoke damage. 7.
Page 13
• French • German • Hebrew • Italian • Korean • Spanish DANGER Electrical current from power, telephone and communication cables is hazardous. To avoid a shock hazard: • Do not connect or disconnect any cables or perform installation, maintenance, or reconfiguration of this product during an electrical storm.
Page 14
CAUTION: When laser products (such as CD-ROMs, DVD-ROM drives, fiber optic devices, or transmitters) are installed, note the following: • Do not remove the covers. Removing the covers of the laser product could result in exposure to hazardous laser radiation. There are no serviceable parts inside the device. •...
Page 16
≥18 kg (37 lbs) ≥32 kg (70.5 lbs) ≥55 kg (121.2 lbs) PERIGO ThinkCentre Hardware Maintenance Manual...
Page 17
A corrente elétrica proveniente de cabos de alimentação, de telefone e de comunicações é perigosa. Para evitar risco de choque elétrico: • Não conecte nem desconecte nenhum cabo ou execute instalação, manutenção ou reconfiguração deste produto durante uma tempestade com raios. •...
Page 18
• Não remova as tampas. A remoção das tampas de um produto a laser pode resultar em exposição prejudicial à radiação de laser. Não existem peças que podem ser consertadas no interior do dispositivo. • A utilização de controles ou ajustes ou a execução de procedimentos diferentes dos especificados aqui pode resultar em exposição prejudicial à...
Page 22
DANGER Le courant électrique provenant de l'alimentation, du téléphone et des câbles de transmission peut présenter un danger. Pour éviter tout risque de choc électrique : • Ne manipulez aucun câble et n'effectuez aucune opération d'installation, d'entretien ou de reconfiguration de ce produit au cours d'un orage.
Page 23
Connexion 1. Mettez les unités HORS TENSION. 2. Commencez par brancher tous les cordons sur les unités. 3. Branchez les câbles d'interface sur des connecteurs. 4. Branchez les cordons d'alimentation sur des prises. 5. Mettez les unités SOUS TENSION. ATTENTION: Remplacer la pile au lithium usagée par une pile de référence identique exclusivement, (référence 45C1566), ou suivre les instructions du fabricant qui en définit les équivalences.
Page 24
≥18 kg (37 lbs) ATTENTION: Soulevez la machine avec précaution. ATTENTION: L'interrupteur de contrôle d'alimentation de l'unité et l'interrupteur dubloc d'alimentation ne coupent pas le courant électrique alimentantl'unité. En outre, le système peut être équipé de plusieurs cordonsd'alimentation. Pour mettre l'unité hors tension, vous devez déconnectertous les cordons de la source d'alimentation.
Page 25
• Die Verbindung zu den angeschlossenen Netzkabeln, Telekommunikationssystemen, Netzwerken und Modems ist vor dem Öffnen des Gehäuses zu unterbrechen, sofern in den Installations- und Konfigurationsprozeduren keine anders lautenden Anweisungen enthalten sind. • Zum Installieren, Transportieren und Öffnen der Abdeckungen des Computers oder der angeschlossenen Einheiten die Kabel gemäß...
Page 26
Laserstrahlung bei geöffneter Verkleidung. Nicht in den Strahl blicken. Keine Lupen oder Spiegel verwenden. Strahlungsbereich meiden. ≥18 kg (37 lbs) ≥32 kg (70.5 lbs) ≥55 kg (121.2 lbs) ACHTUNG: Arbeitsschutzrichtlinien beim Anheben der Maschine beachten. ACHTUNG: Mit dem Netzschalter an der Einheit und am Netzteil wird die Stromversorgung für die Einheit nicht unterbrochen.
Page 28
PERICOLO La corrente elettrica proveniente dai cavi di alimentazione, del telefono e di comunicazione può essere pericolosa. Per evitare il rischio di scosse elettriche: • Non collegare o scollegare qualsiasi cavo oppure effettuare l'installazione, la manutenzione o la riconfigurazione del prodotto durante un temporale. •...
Page 29
• Se possibile, utilizzare solo una mano per collegare o scollegare i cavi di segnale. • Non accendere assolutamente apparecchiature in presenza di incendi, perdite d'acqua o danno strutturale. • Scollegare i cavi di alimentazione, i sistemi di telecomunicazione, le reti e il modem prima di aprire i coperchi del dispositivo, salvo istruzioni contrarie relative alle procedure di installazione e configurazione.
Page 30
PERICOLO Alcune unità laser contengono un diodo laser di Classe 3A o Classe 3B. Tener presente quanto segue: Aprendo l'unità vengono emesse radiazioni laser. Non fissare il fascio, non guardarlo direttamente con strumenti ottici ed evitare l'esposizione al fascio. ≥18 kg (37 lbs) ≥32 kg (70.5 lbs) ≥55 kg (121.2 lbs) ATTENZIONE:...
Page 32
PELIGRO La corriente eléctrica procedente de cables de alimentación, teléfonos y cables de comunicación puede ser peligrosa. Para evitar el riesgo de descarga eléctrica: • No conecte ni desconecte los cables ni realice ninguna tarea de instalación, mantenimiento o reconfiguración de este producto durante una tormenta eléctrica. •...
Page 33
• Desconecte los cables de alimentación, los sistemas de telecomunicaciones, las redes y los módems conectados antes de abrir las cubiertas de los dispositivos, a menos que se indique lo contrario en los procedimientos de instalación y configuración. • Conecte y desconecte los cables, como se describe en la tabla siguiente, cuando instale, mueva o abra las cubiertas de este producto o de los dispositivos conectados.
Page 34
Algunos productos láser tienen incorporado un diodo láser de clase 3A o clase 3B. Tenga en cuenta lo siguiente: Cuando se abre, queda expuesto a radiación láser. No mire directamente al rayo láser, ni siquiera con instrumentos ópticos, y evite exponerse directamente al rayo láser. ≥18 kg (37 lbs) ≥32 kg (70.5 lbs) ≥55 kg (121.2 lbs)
Internet access to view the publication. To view the publication, click Start ® All Programs ® Online Books ® Online Books, then double-click the appropriate publication for your computer. The publication is also available on the Lenovo Support Web site at: http://www.lenovo.com/support...
• To open the Access Help information system on Windows 7, click Start ® Help and Support ® Lenovo Access Help. • To open the Access Help information system on Windows Vista or Windows XP, click Start ® All Programs ®...
Page 37
Dimensions Width: 175 mm (6.9 inches) Height: 412 mm (16.2 inches) Depth: 442 mm (17.4 inches) Weight Maximum configuration as shipped: 11.0 kg (24.3 lbs) Environment • Air temperature: Operating: 10° to 35°C (50° to 95°F) Non-operating: -40° to 60°C (-40° to 140°F) (with package) Non-operating: -10°...
Page 40
– Has this configuration ever worked? – If it has been working, what changes were made prior to it failing? – Is this the original reported failure? • Diagnostics version – Type and version level • Hardware configuration – Print (print screen) configuration currently in use –...
To run the Lenovo System Toolbox program, click Start ® All Programs ® Lenovo Services ® Lenovo System Toolbox. Follow the instructions on the screen. For additional information about running the Lenovo System Toolbox program, refer to the Lenovo System Toolbox help system.
PC-Doctor for Rescue and Recovery The PC-Doctor for Rescue and Recovery diagnostic program is part of the Rescue and Recovery workspace on each Lenovo computer. Use the PC-Doctor for Rescue and Recovery program if you are unable to start the Windows operating system.
3. Follow the instructions on the screen to select the diagnostic test you want to run. Note: For additional help, press the F1 key. 4. Remove the diagnostic disc from the optical drive when you complete the diagnostic process. Navigating through the diagnostics programs Use the cursor movement keys to navigate within the menus.
• Date: Contains the date when the diagnostic test was run. The date is retrieved from CMOS and displayed using the YYYYMMDD format. • ChkDigits: Contains a 2-digit check-digit value to ensure the following: – Diagnostics were run on the specified date. –...
Password considerations A password can be any combination of up to 16 (1 to 16) alphabetic and numeric characters. For security reasons, it is recommended to use a strong password that cannot be easily compromised. To set a strong password, use the following guidelines: Note: The Setup Utility program passwords are not case sensitive.
SATA Controller When this option is set to Disabled, all devices connected to the SATA connectors (such as the hard disk drive or the optical drive) are disabled and will not be displayed in the system configuration. Serial Port1 Address Use this option to control the Input/Output of the serial port.
To view or permanently change the configured startup device sequence, do the following: 1. Start the Setup Utility program. See “Starting the Setup Utility program” on page 39. 2. Select Startup ® Primary Boot Sequence. Read the information displayed on the right side of the screen.
Page 50
In the following index, X can represent any number. Diagnostic error code 000-000-XXX BIOS Test Passed 000-002-XXX BIOS Timeout 000-024-XXX BIOS Addressing test failure 000-025-XXX BIOS Checksum Value error 000-026-XXX FLASH data error 000-027-XXX BIOS Configuration/Setup error 000-034-XXX BIOS Buffer Allocation failure 000-035-XXX BIOS Reset Condition detected 000-036-XXX BIOS Register error 000-038-XXX BIOS Extension failure...
Page 51
Diagnostic error code 000-197-XXX BIOS test warning 000-198-XXX BIOS test aborted 000-199-XXX BIOS test failed, cause unknown 000-250-XXX BIOS APM failure 000-270-XXX BIOS ACPI failure 001-000-XXX System Test Passed 001-00X-XXX System Error 001-01X-XXX System Error 001-024-XXX System Addressing test failure 001-025-XXX System Checksum Value error 001-026-XXX System FLASH data error 001-027-XXX System Configuration/Setup error...
Page 52
Diagnostic error code 001-038-XXX System Extension failure 001-039-XXX System DMI data structure error 001-040-XXX System IRQ failure 001-041-XXX System DMA failure 001-195-XXX System Test aborted by user 001-196-XXX System test halt, error threshold exceeded 001-197-XXX System test warning 001-198-XXX System test aborted 001-199-XXX System test failed, cause unknown 001-250-XXX System ECC error 001-254-XXX 001-255-XXX 001-256-XXX 001-257-XXX...
Page 53
Diagnostic error code 001-273-XXX System IRQ6 (diskette drive) failure 001-274-XXX System IRQ7 failure 001-275-XXX System IRQ8 failure 001-276-XXX System IRQ9 failure 001-277-XXX System IRQ10 failure 001-278-XXX System IRQ11 failure 001-279-XXX System IRQ12 failure 001-280-XXX System IRQ13 failure 001-281-XXX System IRQ14 (hard disk drive) failure 001-282-XXX System IRQ15 failure 001-286-XXX 001-287-XXX 001-288-XXX System Timer failure...
Page 54
Diagnostic error code 005-016-XXX Video Simple Pattern test failure 005-024-XXX Video Addressing test failure 005-025-XXX Video Checksum Value error 005-027-XXX Video Configuration/Setup error 005-031-XXX Video Device Cable failure 005-032-XXX Video Device Controller failure 005-036-XXX Video Register error 005-038-XXX System BIOS extension failure 005-040-XXX Video IRQ failure 005-195-XXX Video Test aborted by user 005-196-XXX Video test halt, error threshold exceeded...
Page 55
Diagnostic error code 005-2XX-XXX 005-3XX-XXX Video subsystem error 006-000-XXX Diskette interface Test Passed 006-0XX-XXX Diskette interface error 006-195-XXX Diskette interface Test aborted by user 006-196-XXX Diskette interface test halt, error threshold exceeded 006-197-XXX Diskette interface test warning 006-198-XXX Diskette interface test aborted 006-199-XXX Diskette interface test failed, cause unknown 006-25X-XXX Diskette interface Error...
Page 56
Diagnostic error code 011-196-XXX Serial port test halt, error threshold exceeded 011-197-XXX Serial port test warning 011-198-XXX Serial port test aborted 011-199-XXX Serial port test failed, cause unknown 011-2XX-XXX Serial port signal failure 014-000-XXX Parallel port Interface Test Passed 014-001-XXX Parallel port Presence 014-002-XXX 014-003-XXX Parallel port Timeout/Parity error 014-013-XXX 014-014-XXX Parallel port Control...
Page 57
Diagnostic error code 014-197-XXX Parallel port test warning 014-198-XXX Parallel port test aborted 014-199-XXX Parallel port test failed, cause unknown 014-2XX-XXX 014-3XX-XXX Parallel port failure 015-000-XXX USB (Universal Serial Bus) port Interface Test Passed 015-001-XXX USB port Presence 015-002-XXX USB port Timeout 015-015-XXX USB port External Loopback failure 015-027-XXX USB port Configuration/Setup error 015-032-XXX USB port Device Controller failure...
Page 58
Diagnostic error code 015-196-XXX USB port test halt, error threshold exceeded 015-197-XXX USB port test warning 015-198-XXX USB port test aborted 015-199-XXX USB port test failed, cause unknown 018-000-XXX PCI (Peripheral Component Interconnect) Card Test Passed 018-0XX-XXX PCI Card Failure 018-195-XXX PCI Card Test aborted by user 018-196-XXX PCI Card test halt, error threshold exceeded 018-197-XXX PCI Card test warning...
Page 59
Diagnostic error code 018-250-XXX PCI Card Services error 020-000-XXX PCI Interface Test Passed 020-0XX-XXX PCI Interface error 020-195-XXX PCI Test aborted by user 020-196-XXX PCI test halt, error threshold exceeded 020-197-XXX PCI test warning 020-198-XXX PCI test aborted 020-199-XXX PCI test failed, cause unknown 020-262-XXXPCI system error 025-000-XXXIDE interface Test Passed 025-00X-XXX 025-01X-XXX IDE interface failure...
Page 60
Diagnostic error code 025-02X-XXX 025-03X-XXX 025-04X-XXX IDE Interface failure 025-195-XXX IDE interface Test aborted by user 025-196-XXX IDE interface test halt, error threshold exceeded 025-197-XXX IDE interface test warning 025-198-XXX IDE interface test aborted 025-199-XXX IDE interface test failed, cause unknown 030-000-XXX SCSI interface Test Passed 030-00X-XXX 030-01X-XXX SCSI interface failure 030-027-XXX SCSI interface Configuration/Setup error...
Page 61
Diagnostic error code 030-196-XXX SCSI interface test halt, error threshold exceeded 030-197-XXX SCSI interface test warning 030-198-XXX SCSI interface test aborted 030-199-XXX SCSI interface test failed, cause unknown 035-000-XXX RAID interface Test Passed 035-0XX-XXX RAID interface Failure 035-195-XXX RAID interface Test aborted by user 035-196-XXX RAID interface test halt, error threshold exceeded 035-197-XXX RAID interface test warning...
Page 62
Diagnostic error code 071-00X-XXX 071-01X-XXX 071-02X-XXXAudio port error 071-03X-XXX Audio port failure 071-04X-XXX Audio port failure 071-195-XXX Audio port Test aborted by user 071-196-XXX Audio port test halt, error threshold exceeded 071-197-XXX Audio port test warning 071-198-XXX Audio port test aborted 071-199-XXX Audio port test failed, cause unknown 071-25X-XXX Audio port failure 080-000-XXX Game Port interface Test Passed...
Page 63
Diagnostic error code 080-197-XXX Game Port interface test warning 080-198-XXX Game Port interface test aborted 080-199-XXX Game Port interface test failed, cause unknown 086-000-XXX Mouse Port interface Test Passed 086-001-XXX Mouse Port interface Presence 086-032-XXX Mouse Port interface Device controller failure 086-035-XXX Mouse Port interface Reset 086-040-XXX Mouse Port interface IRQ failure...
Page 64
Diagnostic error code 086-199-XXX Mouse Port interface test failed, cause unknown 089-000-XXX Microprocessor Test Passed 089-XXX-XXX Microprocessor failure 089-195-XXX Microprocessor Test aborted by user 089-196-XXX Microprocessor test halt, error threshold exceeded 089-197-XXX Microprocessor test warning 089-198-XXX Microprocessor test aborted 089-199-XXX Microprocessor test failed, cause unknown 170-000-XXX Voltage Sensor(s) Test Passed 170-0XX-XXX Voltage Sensor(s) failure 170-195-XXX Voltage Sensor(s) Test aborted by user...
Page 65
Diagnostic error code 170-199-XXX Voltage Sensor(s) test failed, cause unknown 170-250-XXX 170-251-XXX Voltage Sensor(s) Voltage limit error 170-254-XXX Voltage Sensor(s) Voltage Regulator Module error 175-000-XXX Thermal Sensor(s) Test Passed 175-0XX-XXX Thermal Sensor(s) failure 175-195-XXX Thermal Sensor(s) Test aborted by user 175-196-XXX Thermal Sensor(s) test halt, error threshold exceeded 175-197-XXX Thermal Sensor(s) test warning...
Page 66
Diagnostic error code 201-XXX-XXX System Memory error 202-000-XXX System Cache Test Passed 202-XXX-XXX System Cache error 206-000-XXX Diskette Drive Test Passed 206-XXX-XXX Diskette Drive error 215-000-XXX CD-ROM Drive Test Passed 215-XXX-XXX CD-ROM Drive error 217-000-XXX Hard Disk Drive Test Passed 217-25X-XXX 217-26X-XXX Hard Disk Drive (IDE) error 217-28X-XXX 217-29X-XXX Hard Disk Drive (SCSI) error 220-000-XXX Hi-Capacity Cartridge Drive Test Passed...
Diagnostic error code 305-000-XXX Monitor DDC Test Passed 305-250-XXX Monitor DDC self test failure 415-000-XXXModem Test Passed 415-XXX-XXX Modem error Beep symptoms Beep symptoms are tones or a series of tones separated by pauses (intervals without sound) during POST. The following tables describes beep symptoms. Beep symptom 2 short beeps CMOS setting error 1 long and 2 short beeps Monitor or video adapter card...
Beep symptom Continuos long beeps DRAM memory error POST error codes Each time you power-on the system, it performs a series of tests that check the operation of the system and some options. This series of tests is called the Power-On Self-Test, or POST. POST does the following operations.
POST error message Memory test fail Press TAB to show POST screen Error: Non-System disk or disk error Replace and press any key when ready Miscellaneous error messages Message/Symptom Changing display colors Computer will not power-off. See “Hard disk drive boot error”...
Page 70
Message/Symptom Incorrect memory size during POST "Insert a Diskette" icon appears with a known-good diagnostics diskette in the first 3.5-inch diskette drive. Intensity or color varies from left to right of characters and color bars No power or fan not running Non-system disk or disk error-type message with a known-good diagnostic diskette.
Message/Symptom Serial or parallel port device failure (adapter port) Some or all keys on the keyboard do not work Undetermined problems This section provides instructions on how to find out the failing devices or adapters. 1. Power-off the computer. 2. Remove or disconnect the following components (if installed) one at a time. a.
Do not open your computer or attempt any repair before reading and understanding the “Important safety information” in the ThinkCentre Safety and Warranty Guide that came with your computer. To obtain a copy of the ThinkCentre Safety and Warranty Guide, go to: http://www.lenovo.com/support This section provides instructions on how to remove the computer cover. CAUTION: Turn off the computer and wait three to five minutes to let the computer cool before removing the computer cover.
1. Remove any media from the drives and turn off all attached devices and the computer. 2. Unplug all power cords from electrical outlets. 3. Disconnect the cables attached to the computer. This includes power cords, Input/Output (I/O) cables, and any other cables that are connected to the computer. See “Locating connectors on the front of your computer”...
Figure 4. Component locations Heat sink and fan assembly Memory modules Battery PCI Express x16 graphics card slot PCI card Locating parts on the system board Figure 5 “System board part locations” on page 71 shows the locations of the parts on the system board. ThinkCentre Hardware Maintenance Manual PCI card slot PCI Express x1 card slots...
ThinkCentre Safety and Warranty Guide that came with your computer. To obtain a copy of the ThinkCentre Safety and Warranty Guide, go to: http://www.lenovo.com/support This section provides instructions on how to remove and reinstall the front bezel. Cover presence switch connector(also called intrusion...
ThinkCentre Safety and Warranty Guide that came with your computer. To obtain a copy of the ThinkCentre Safety and Warranty Guide, go to: http://www.lenovo.com/support This section provides instructions on how to install or replace a memory module. Your computer has two slots for installing or replacing DDR3 DIMMs that provide up to a maximum of 4 GB system memory.
Page 79
3. Locate the memory slots. See “Locating parts on the system board” on page 70. 4. Open the retaining clips. Figure 7. Opening the retaining clips If you are replacing an old memory module, open the retaining clips and remove the memory module being replaced as shown.
ThinkCentre Safety and Warranty Guide that came with your computer. To obtain a copy of the ThinkCentre Safety and Warranty Guide, go to: http://www.lenovo.com/support This section provides instructions on how to install or replace a PCI card. Your computer has one standard PCI card slot, two PCI Express x1 card slots, and one PCI Express x16 graphics card slot.
Page 81
4. Install the new card into the appropriate card slot on the system board. See “Locating parts on the system board” on page 70. If you are replacing a PCI card, remove the old card currently installed before installing the new one. Figure 11.
ThinkCentre Safety and Warranty Guide that came with your computer. To obtain a copy of the ThinkCentre Safety and Warranty Guide, go to: http://www.lenovo.com/support Your computer has a special type of memory that maintains the date, time, and settings for built-in features, such as parallel-port assignments (configuration).
ThinkCentre Safety and Warranty Guide that came with your computer. To obtain a copy of the ThinkCentre Safety and Warranty Guide, go to: http://www.lenovo.com/support This section provides instructions on how to replace the power supply assembly. To replace the power supply assembly, do the following: 1.
7. Install the four screws to secure the power supply assembly. Note: Use only screws provided by Lenovo. 8. Reconnect the power supply assembly connectors to the system board. 9. Reconnect a power supply assembly connector to each of the drives.
Page 85
CAUTION: The heat sink and fan assembly might be very hot. Turn off the computer and wait three to five minutes to let the computer cool before removing the computer cover. To replace the heat sink and fan assembly, do the following: 1.
Do not open your computer or attempt any repair before reading and understanding the “Important safety information” in the ThinkCentre Safety and Warranty Guide that came with your computer. To obtain a copy of the ThinkCentre Safety and Warranty Guide, go to: http://www.lenovo.com/support This section provides instructions on how to replace the microprocessor. CAUTION: The heat sink and microprocessor might be very hot.
Page 87
8. Lift the microprocessor straight up and out of the socket. Notes: a. Your microprocessor and socket might look different from the one illustrated. b. Note the orientation of the microprocessor in the socket. You can look for the small triangle on one corner of the microprocessor.
Do not open your computer or attempt any repair before reading and understanding the “Important safety information” in the ThinkCentre Safety and Warranty Guide that came with your computer. To obtain a copy of the ThinkCentre Safety and Warranty Guide, go to: http://www.lenovo.com/support This section provides instructions on how to replace the system board. CAUTION: The heat sink and microprocessor might be very hot.
ThinkCentre Safety and Warranty Guide that came with your computer. To obtain a copy of the ThinkCentre Safety and Warranty Guide, go to: http://www.lenovo.com/support This section provides instructions on how to replace the primary hard disk drive. To replace the primary hard disk drive, do the following: 1.
Page 90
5. Remove the hard disk drive cage from the chassis by simply sliding it outward. 6. Pull on the blue handle to release and remove the hard disk drive from the drive cage. 7. Remove the hard disk drive from the blue bracket by flexing the sides of the bracket enough to slide it free from the hard disk drive.
ThinkCentre Safety and Warranty Guide that came with your computer. To obtain a copy of the ThinkCentre Safety and Warranty Guide, go to: http://www.lenovo.com/support Note: Depending on your model type, your computer might come with a secondary hard disk drive bay for installing or replacing a secondary hard disk drive.
Page 92
Figure 21. Removing the secondary hard disk drive 5. Remove the hard disk drive cage from the chassis by simply sliding it outward. 6. Pull on the blue handle to release and remove the hard disk drive from the hard disk drive cage. 7.
ThinkCentre Safety and Warranty Guide that came with your computer. To obtain a copy of the ThinkCentre Safety and Warranty Guide, go to: http://www.lenovo.com/support This section provides instructions on how to replace the optical drive. To replace the optical drive, do the following: 1.
Page 94
Figure 24. Removing the optical drive 6. Install the optical drive retainer into the optical drive bay from the front until it snaps into position. Figure 25. Installing the optical drive 7. Connect the signal cable and the power cable to the rear of the new optical drive. See “Connecting a SATA drive”...
ThinkCentre Safety and Warranty Guide that came with your computer. To obtain a copy of the ThinkCentre Safety and Warranty Guide, go to: http://www.lenovo.com/support Depending on your model type, your computer might have a card reader installed. This section provides instructions on how to replace the card reader.
ThinkCentre Safety and Warranty Guide that came with your computer. To obtain a copy of the ThinkCentre Safety and Warranty Guide, go to: http://www.lenovo.com/support This section provides instructions on how to replace the front fan assembly. Note: Depending on model type, your computer might have a front fan assembly installed.
Page 97
To replace the front fan assembly, do the following: 1. Turn off the computer and disconnect all power cords from electrical outlets. 2. Remove the computer cover. See “Removing the computer cover” on page 68. 3. Remove the front bezel. See “Removing and reinstalling the front bezel” on page 71. 4.
ThinkCentre Safety and Warranty Guide that came with your computer. To obtain a copy of the ThinkCentre Safety and Warranty Guide, go to: http://www.lenovo.com/support This section provides instructions on how to replace the rear fan assembly. To replace the rear fan assembly, do the following: 1.
Page 99
Figure 32. Removing the rear fan assembly 5. Install the new rear fan assembly by aligning the new rubber mounts of the new rear fan assembly with the holes on the chassis and push the rubber mounts through the holes. Note: The new rear fan assembly you received will have four new rubber mounts attached.
ThinkCentre Safety and Warranty Guide that came with your computer. To obtain a copy of the ThinkCentre Safety and Warranty Guide, go to: http://www.lenovo.com/support This section provides instructions on how to replace the internal speaker. To replace the internal speaker, do the following: 1.
Page 101
Figure 34. Removing the old internal speaker 5. Position a new internal speaker into the metal clips and push downward on the internal speaker until it snaps into position. Figure 35. Installing a new internal speaker 6. Connect the speaker cable to the system board. See “Locating parts on the system board” on page 70. 7.
ThinkCentre Safety and Warranty Guide that came with your computer. To obtain a copy of the ThinkCentre Safety and Warranty Guide, go to: http://www.lenovo.com/support This section provides instructions on how to replace the front audio and USB assembly.
Completing the FRU replacement This section provides instructions on how to complete the FRU replacement. After replacing the FRUs, you need to reinstall any removed parts, reconnect and route any internal cables, reinstall the computer cover, and reconnect any external cables, such as power cords. Depending on the FRUs replaced, you might need to confirm the updated information in the Setup Utility program, see Chapter 6 “Using the Setup Utility program”...
Page 104
8. Some FRU replacements require the configuration to be updated. To update your configuration, see Chapter 6 “Using the Setup Utility program” on page 39. ThinkCentre Hardware Maintenance Manual...
Page 106
Item # AMD AM2/AM3 65W cooler kit (no fan grill) • MT 3317: all models • MT 4013: all models • MT 5043: all models • MT 5237: all models • MT 5393: all models • MT 6674: all models System board, planar RS760V non-AMT mATX GA •...
Item # Intrusion switch assembly • MT 3317: all models • MT 4013: all models • MT 5043: all models • MT 5237: all models • MT 5393: all models • MT 6674: all models System fan (no fan grill) •...
Page 119
FRU, front fan (with fan bracket) • MT 3317: all models • MT 4013: all models • MT 5043: all models • MT 5237: all models • MT 5393: all models • MT 6674: all models FRU, L1 -models with NO FDD/card reader, Tampa •...
Page 120
FRU, 2st HDD SATA cable, 120mm, 1 latching for device, RoHS • MT 3317: all models • MT 4013: all models • MT 5043: all models • MT 5237: all models • MT 5393: all models • MT 6674: all models FRU, rear USB 2 ports II HP 300mm •...
Page 121
FRU, cable-SATA 250mm (RoHS) for 1st HDD • MT 3317: all models • MT 4013: all models • MT 5043: all models • MT 5237: all models • MT 5393: all models • MT 6674: all models FRU, HDD tray, Tamdhu •...
Page 122
FRU, USB cover, Tampa • MT 3317: all models • MT 4013: all models • MT 5043: all models • MT 5237: all models • MT 5393: all models • MT 6674: all models FRU, top handle assembly, Tampa • MT 3317: all models •...
Page 123
FRU, Tamdhu chassis primary HDD cage • MT 3317: all models • MT 4013: all models • MT 5043: all models • MT 5237: all models • MT 5393: all models • MT 6674: all models FRU, front bezel with ODD door assembly, Tampa •...
• MT 5237: all models • MT 5393: all models • MT 6674: all models Keyboard and Mouse Keyboard (Lenovo Preferred Pro USB -- without hub) US English • MT 3317: • MT 4013: A4A A7U A5A A6A B1Q B2U B3U B4U •...
Page 125
Keyboard (Lenovo Preferred Pro USB -- without hub) French Canadian • MT 3317: • MT 4013: A7F B2F B3F B4F • MT 5043: A1F A3F A4F A5F AEF AFF AGF • MT 5237: AAF • MT 5393: • MT 6674: A4F A6F A8F ABF A3F AFF ANF APF ARF ASF French Canadian •...
Windows Vista 32 Home Basic Recovery CD Windows Vista 32 Home Basic India English • MT 3317: • MT 4013: • MT 5043: • MT 5237: • MT 5393: • MT 6674: Windows Vista Home Basic 32 with MS office starter 2010 Recovery CD Windows Vista Home Basic 32 with MS office starter 2010 India English •...
Page 173
Windows Vista Business 32 India English • MT 3317: • MT 4013: • MT 5043: • MT 5237: • MT 5393: • MT 6674: Italian • MT 3317: • MT 4013: • MT 5043: • MT 5237: • MT 5393: •...
Windows Vista Business 32 Office Starter 2010 Recovery CD Windows Vista Business 32 Office Starter 2010 English • MT 3317: • MT 4013: • MT 5043: • MT 5237: • MT 5393: • MT 6674: French • MT 3317: • MT 4013: •...
Windows 7 Professional 32 with MS office starter 2010 Recovery CD Windows 7 Professional 32 with MS office starter 2010 Arabic enabled • MT 3317: • MT 4013: • MT 5043: • MT 5237: • MT 5393: • MT 6674: Brazil •...
Page 191
Windows 7 Professional 32 with MS office starter 2010 India English • MT 3317: • MT 4013: • MT 5043: • MT 5237: • MT 5393: • MT 6674: French • MT 3317: • MT 4013: • MT 5043: • MT 5237: •...
Windows 7 Professional 32 with MS office starter 2010 C&L Nordics (EN DK FI NO SV) • MT 3317: • MT 4013: • MT 5043: • MT 5237: • MT 5393: • MT 6674: C&L EMEA (FR NL GR IT EN) •...
Windows 7 Professional 64 with MS office starter 2010 Recovery CD Windows 7 Professional 64 with MS office starter 2010 Brazil • MT 3317: • MT 4013: • MT 5043: • MT 5237: • MT 5393: • MT 6674: Simplified Chinese •...
Page 199
Windows 7 Professional 64 with MS office starter 2010 German • MT 3317: • MT 4013: • MT 5043: • MT 5237: • MT 5393: • MT 6674: Hong Kong • MT 3317: • MT 4013: • MT 5043: • MT 5237: •...
Windows 7 Professional 64 with MS office starter 2010 C&L Nordics (EN DK FI NO SV) • MT 3317: • MT 4013: • MT 5043: • MT 5237: • MT 5393: • MT 6674: C&L Switzerland (EN FR GR IT) •...
Page 201
Windows 7 Home Premium 64 French • MT 3317: • MT 4013: • MT 5043: • MT 5237: • MT 5393: • MT 6674: Hong Kong • MT 3317: • MT 4013: • MT 5043: • MT 5237: • MT 5393: •...
– Start the Setup Utility. – Select System Information on the Main setup screen. • Sources for obtaining the latest level BIOS available 1. Lenovo support web site: http://www.lenovo.com/support/ 2. Lenovo Customer Support Center 3. Levels 1 and 2 Support To update (flash) the BIOS, see “Updating (flashing) BIOS from a disc”...
5. Follow the instructions on the screen to complete the update. Updating (flashing) BIOS from your operating system Note: Because Lenovo makes constant improvements to the Web site, the Web page contents are subject to change without notice, including the contents referenced in the following procedure.
9. Turn on the computer and the monitor. Then, insert the POST/BIOS update (flash update) disc into the optical drive. 10. Turn the computer off and back on again. The recovery begins. 11. The recovery session will take two to three minutes. During this time you will hear a series of beeps. After the update session is completed, there will be no video, the series of beeps will end, and the system will automatically turn off.
Lenovo representative for information on the products and services currently available in your area. Any reference to a Lenovo product, program, or service is not intended to state or imply that only that Lenovo product, program, or service may be used. Any functionally equivalent product, program, or service that does not infringe any Lenovo intellectual property right may be used instead.
Macrovision Corporation. Reverse engineering or disassembly is prohibited. Trademarks The following terms are trademarks or service marks of Lenovo in the United States, other countries, or both: Lenovo The Lenovo logo...
Page 216
Part Number: 71Y5807 Printed in USA (1P) P/N: 71Y5807 *71Y5807*...