Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Dell C734G
Summary of Contents for Dell C734G
- Page 1 Questo manuale d’istruzione è fornito da trovaprezzi.it. Scopri tutte le offerte per Dell Vostro 3400 C734G o cerca il tuo prodotto tra le migliori offerte di Notebook Vostro 3400 Service Manual Regulatory Model: P132G Regulatory Type: P132G003 / P132G004 October 2021...
- Page 2 A WARNING indicates a potential for property damage, personal injury, or death. © 2020-2021 Dell Inc. or its subsidiaries. All rights reserved. Dell, EMC, and other trademarks are trademarks of Dell Inc. or its subsidiaries. Other trademarks may be trademarks of their respective owners.
-
Page 3: Table Of Contents
Contents Chapter 1: Working on your computer................... 6 Safety instructions................................6 Before working inside your computer........................6 Safety instructions.................................7 Electrostatic discharge—ESD protection........................7 ESD field service kit ..............................8 After working inside your computer..........................9 Chapter 2: Technology and components..................10 USB features..................................10 Power button LED behavior............................ - Page 4 Coin-cell battery................................40 Removing the coin-cell...............................40 Installing the coin-cell battery...........................41 System fan...................................41 Removing the system fan............................41 Installing the system fan............................42 Heat sink....................................43 Removing the Heatsink - UMA..........................43 Installing the Heatsink - UMA...........................44 Removing the Heatsink - Discrete.......................... 45 Installing the Heatsink - Discrete..........................46 Speakers....................................
- Page 5 Handling swollen Lithium-ion batteries........................82 Locate the Service Tag or Express Service Code of your Dell computer ..........83 SupportAssist | On-board Diagnostics......................... 83 System diagnostic lights..............................83 Real-Time Clock (RTC Reset)............................85 Updating the BIOS in Windows............................85 Updating the BIOS using the USB drive in Windows....................85 Backup media and recovery options..........................85...
-
Page 6: Chapter 1: Working On Your Computer
Damage due to servicing that is not authorized by Dell is not covered by your warranty. Read and follow the safety instructions that came with the product. -
Page 7: Safety Instructions
ESD protection is an increasing concern. Due to the increased density of semiconductors used in recent Dell products, the sensitivity to static damage is now higher than in previous Dell products. For this reason, some previously approved methods of handling parts are no longer applicable. -
Page 8: Esd Field Service Kit
Two recognized types of ESD damage are catastrophic and intermittent failures. ● Catastrophic – Catastrophic failures represent approximately 20 percent of ESD-related failures. The damage causes an immediate and complete loss of device functionality. An example of catastrophic failure is a memory DIMM that has received a static shock and immediately generates a "No POST/No Video"... -
Page 9: After Working Inside Your Computer
It is recommended that all field service technicians use the traditional wired ESD grounding wrist strap and protective anti-static mat at all times when servicing Dell products. In addition, it is critical that technicians keep sensitive parts separate from all insulator parts while performing service and that they use anti-static bags for transporting sensitive components. -
Page 10: Chapter 2: Technology And Components
Technology and components This chapter details the technology and components available in the system. Topics: • USB features • Power button LED behavior • HDMI 1.4 USB features Universal Serial Bus, or USB, was introduced in 1996. It dramatically simplified the connection between host computers and peripheral devices like mouses, keyboards, external drivers, and printers. - Page 11 ● USB 3.2 Gen 1 utilizes the bi-directional data interface, rather than USB 2.0's half-duplex arrangement. This gives a 10-fold increase in theoretical bandwidth. With today's ever increasing demands that are placed on data transfers with high-definition video content, terabyte storage devices, high megapixel count digital cameras etc., USB 2.0 may not be fast enough.
-
Page 12: Power Button Led Behavior
Power button LED behavior On certain Dell Latitude systems, the power button LED is used to provide an indication of the system status, and as a result the power button illuminates when pressed. The systems with the optional power button/fingerprint reader will have no LED under the power button and hence will apply the available LED's in the system to provide an indication of the system status. - Page 13 Power button with fingerprint reader will have no LED and will leverage the available LED's in the system to provide indication of the system status ● Power Adapter LED: ○ The LED on Power adapter connector illuminates white when power is supplied from electrical outlet. ●...
-
Page 14: Hdmi 1.4
HDMI 1.4 This topic explains the HDMI 1.4 and its features along with the advantages. HDMI (High-Definition Multimedia Interface) is an industry-supported, uncompressed, all-digital audio/video interface. HDMI provides an interface between any compatible digital audio/video source, such as a DVD player, or A/V receiver and a compatible digital audio and/or video monitor, such as a digital TV (DTV). -
Page 15: Chapter 3: Exploded View
Exploded View... - Page 16 Exploded View Exploded View...
- Page 17 18. Heatsink assembly NOTE: Dell provides a list of components and their part numbers for the original system configuration purchased. These parts are available according to warranty coverages purchased by the customer. Contact your Dell sales representative for purchase options.
-
Page 18: Chapter 4: Major Components
Major Components Major Components... -
Page 19: Chapter 5: Disassembly And Reassembly
Disassembly and reassembly NOTE: The images in this document may differ from your computer depending on the configuration you ordered. Topics: • Secure Digital Card • Base cover • Battery • Memory modules • WLAN card • Solid-state drive • Hard drive •... -
Page 20: Installing The Secure Digital Card
About this task Steps 1. Push the secure digital card to release it from the computer. 2. Slide the secure digital card out of the computer. Installing the Secure Digital card Prerequisites If you are replacing a component, remove the existing component before performing the installation procedure. Disassembly and reassembly... -
Page 21: Base Cover
About this task Steps Slide the secure digital into the slot until it clicks into place. Next steps 1. Follow the procedure in after working inside your computer. Base cover Removing the base cover Prerequisites 1. Follow the procedure in before working inside your computer. - Page 22 About this task Disassembly and reassembly...
-
Page 23: Installing The Base Cover
Steps 1. Remove the seven (M2.5x5) screws and loosen the two captive screws from the base cover. 2. Pry open the base cover starting from the recesses located in the U-shaped indents at the top edge of the base cover near the hinges. - Page 24 About this task Disassembly and reassembly...
-
Page 25: Battery
● If the battery gets stuck inside your computer as a result of swelling, do not try to release it as puncturing, bending, or crushing a lithium-ion battery can be dangerous. In such an instance, contact Dell technical support for assistance. See www.dell.com/contactdell. -
Page 26: Reconnecting The Battery
About this task Steps 1. Peel back the tape covering the battery connector. 2. Disconnect the battery cable from the connector on the system board. Reconnecting the battery Prerequisites If you are replacing a component, remove the existing component before performing the installation procedure. Disassembly and reassembly... -
Page 27: Removing The Battery
About this task Steps 1. Connect the battery cable to the connector on the system board. 2. Replace the tape covering the battery connector. Next steps 1. Install the base cover. 2. Install the card. 3. Follow the procedure in after working inside your computer. -
Page 28: Installing The Battery
Steps 1. Remove the three (M2x3) screws that secure the battery to the palmrest. 2. Lift and move the battery away from the computer. Installing the battery Prerequisites If you are replacing a component, remove the existing component before performing the installation procedure. Disassembly and reassembly... - Page 29 About this task Steps 1. Align the tabs on the battery with the slots on the palm rest assembly. NOTE: When installing the battery into the system, insert the tab at the bottom left corner of the battery into the hook on the bottom side of the palm rest.
-
Page 30: Memory Modules
Memory modules Removing the memory module Prerequisites 1. Follow the procedure in before working inside your computer. 2. Remove the card. 3. Remove the base cover. 4. Disconnect the battery cable. About this task Steps 1. Pry the clips securing the memory module until the memory module pops-up. 2. -
Page 31: Wlan Card
About this task Steps 1. Align the notch on the memory module with the tab on the memory module slot and slide the memory module firmly into the slot at an angle. 2. Press the memory module down until the clips secure it. NOTE: If you do not hear the click, remove the memory module and reinstall it. -
Page 32: Installing The Wlan Card
About this task Steps 1. Remove the single (M2x3) screw that secures the WLAN card bracket to the system board. 2. Slide and remove the WLAN card bracket that secures the WLAN antenna cables. 3. Disconnect the WLAN antenna cables from the connectors on the WLAN card. 4. - Page 33 About this task Steps 1. Replace the WLAN card into the M.2 Slot on the system board. 2. Connect the WLAN antenna cables to the connectors on the WLAN card. NOTE: Table 3. WLAN Antenna Cables Cable color Indicator on WLAN Blue White triangle Orange...
-
Page 34: Solid-State Drive
Solid-state drive Removing the M.2 2230 Solid-state drive Prerequisites 1. Follow the procedure in before working inside your computer. 2. Remove the card. 3. Remove the base cover. 4. Disconnect the battery cable. About this task Steps 1. Remove the single (M2x2.2) screw and loosen the single captive screw, securing the SSD thermal plate to the palmrest, to lift it out of the system. -
Page 35: Removing The M.2 2280 Solid-State Drive
About this task Steps 1. Place the solid-state drive into the thermal plate and install the single (M2x2) screw. 2. Slide and insert the tab of the solid-state drive into the solid-state drive slot. 3. Replace the single (M2x2.2) screw and tighten the single captive screw to secures the thermal plate to the palmrest. Next steps 1. -
Page 36: Installing The M.2 2280 Solid-State Drive
About this task Steps 1. Remove the two (M2x2.2) screw from the thermal bracket and lift the bracket out of the system. 2. Lift the solid-state drive from the M.2 slot on the system board and remove it from the system. Installing the M.2 2280 Solid-state drive Prerequisites If you are replacing a component, remove the existing component before performing the installation procedure. -
Page 37: Hard Drive
About this task Steps 1. Slide and insert the Solid-state drive into the M.2 port on the system board. 2. Place the thermal bracket on the solid-state drive, replace the two (M2x2.2) screws to secure the thermal plate to the palmrest. -
Page 38: Installing The Hard Drive Assembly
About this task Steps 1. Lift the latch and disconnect the hard drive cable from the system board. 2. Remove the four (M2x3) screws that secure the hard drive assembly to the palmrest and lift the hard drive assembly along with its cable from the system. - Page 39 About this task Steps 1. Align the hard drive with the hard drive bracket and replace the four (M3x3) screws. 2. Connect the interposer to the hard drive. 3. Align and place the hard drive assembly on the palmrest, then replace the four (M2x3) screws to secure the hard drive assembly to the palmrest.
-
Page 40: Coin-Cell Battery
Coin-cell battery Removing the coin-cell Prerequisites 1. Follow the procedure in before working inside your computer. 2. Remove the card. 3. Remove the base cover. 4. Disconnect the battery cable. 5. Remove the board. NOTE: The Coin-cell is installed on the IO board. About this task Steps 1. -
Page 41: Installing The Coin-Cell Battery
Installing the coin-cell battery About this task Steps 1. With the positive-side facing up, insert the coin-cell battery into the battery socket on the I/O board. 2. Press the battery until it clicks into place. Next steps 1. Install the board. -
Page 42: Installing The System Fan
About this task Steps 1. Disconnect the fan cable from the connector on the system board and unthread the cable from the routing points on the fan assembly. 2. Remove the two screws (M2.5x5) that secures the fan to the palmrest. Installing the system fan Prerequisites If you are replacing a component, remove the existing component before performing the installation procedure. -
Page 43: Heat Sink
About this task Steps 1. Align and place the fan on the palm rest. 2. Replace the two screws (M2.5x5) that secure the fan to the palmrest. 3. Route the display cable thought the routing points on the fan assembly, and connect the fan cable to the connector on the system board . -
Page 44: Installing The Heatsink - Uma
About this task Steps 1. Loosen the four captive screws that secure the heatsink to the system board. 2. Lift the heatsink off the system board. Installing the Heatsink - UMA Prerequisites If you are replacing a component, remove the existing component before performing the installation procedure. Disassembly and reassembly... -
Page 45: Removing The Heatsink - Discrete
About this task Steps 1. Place the heatsink on the system board and align the captive screws on the heatsink with the screw holes on the system board. 2. Tiighten the four captive screws to secure the heatsink to the system board. Next steps 1. -
Page 46: Installing The Heatsink - Discrete
About this task Steps 1. Loosen the four captive screws and remove the three (M2x3) screws that secure the heatsink to the system board. 2. Lift the heatsink off the system board. Installing the Heatsink - Discrete Prerequisites If you are replacing a component, remove the existing component before performing the installation procedure. Disassembly and reassembly... -
Page 47: Speakers
About this task Steps 1. Place the heatsink on the system board and align the captive screws on the heatsink with the screw holes on the system board. 2. Tiighten the four captive screws and install the three (M2x4) screws to secure the heatsink to the system board. Next steps 1. -
Page 48: Installing The Speakers
About this task Steps 1. Disconnect the speaker cable from the system board. 2. Unroute and remove the speaker cable from the routing guides on palmrest. 3. Lift the speakers, along with the cable, off the system. Installing the speakers Prerequisites If you are replacing a component, remove the existing component before performing the installation procedure. -
Page 49: Io Board
Steps 1. Using the alignment posts and rubber grommets, place the speakers in the slots on the palm rest. 2. Route the speaker cable through the routing guides on the palmrest. 3. Connect the speaker cable to the connector on the system board . Next steps 1. -
Page 50: Installing The Io Board
About this task Steps 1. [For models shipped with a fingerprint reader] : Disconnect the fingerprint reader to IO daughter board FFC and IO daughter board to system board FFC from the IO daughter board. 2. [For models shipped without a fingerprint reader] : Disconnect the power button FFC, IO daughter board FFC, and display cable from the system board. -
Page 51: Touchpad
About this task Steps 1. Reconnect the power button FFC and IO daughter board FFC to the IO daughter board. 2. Place the IO daughter board onto the from the system. 3. Replace the four (M2x4) screws to secure the IO daughter board to the palmrest. 4. -
Page 52: Installing The Touch Pad Assembly
2. Remove the card. 3. Remove the base cover. 4. Remove the battery. About this task Steps 1. Disconnect the touchpad FFC from the system board. 2. Peel back the conductive tape from the touchpad module. 3. Remove the three (M2x2) screws securing the touchpad bracket in place. 4. - Page 53 Steps 1. Reconnect the touchpad FFC to the touchpad module. 2. Align and place the touchpad module onto the system. NOTE: When installing the touchpad bracket on the Vostro 3400, insert its top corners under the two tabs on the palm rest.
-
Page 54: Display Assembly
Display assembly Removing the display assembly Prerequisites 1. Follow the procedure in before working inside your computer. 2. Remove the card. 3. Remove the base cover. 4. Disconnect the battery cable. 5. Remove the WLAN. About this task Disassembly and reassembly... - Page 55 Steps 1. Disconnect the display cable from the connector on the system board. Disassembly and reassembly...
-
Page 56: Installing The Display Assembly
2. Unthread the display cable and WLAN antenna cables from the routing channels. 3. Open the system to at least 90-degrees and place the system on the edge of a table so that the palm rest is laying flat on the table and the display assembly is over the edge. - Page 57 Steps 1. Align and place the system under the hinges on the display assembly. 2. Install the four (M2.5x5) screws securing the display assembly in place. Disassembly and reassembly...
-
Page 58: Display Bezel
3. Re-route the display cable and WLAN antenna cables through the routing channels on the palmrest. 4. Reconnect the display cable to the connector on the system board. Next steps 1. Install the WLAN. 2. Install the base cover. 3. Install the card. -
Page 59: Installing The Display Bezel
Installing the display bezel Prerequisites If you are replacing a component, remove the existing component before performing the installation procedure. About this task Steps Align the display bezel with the display back-cover and antenna assembly, and then gently snap the display bezel into place. Next steps 1. - Page 60 6. Remove the display assembly. 7. Remove the display bezel. Disassembly and reassembly...
- Page 61 About this task Disassembly and reassembly...
-
Page 62: Installation Display Panel
Steps 1. Remove the six (M2.5x2.5) screws securing the display panel to the hinges. 2. Gently flip the display panel assembly forward, peel back the mylar tape securing the display cable on the rear of the display panel. NOTE: Ensure the panel has a clean and smooth surface to rest on to prevent damage. 3. - Page 63 About this task Disassembly and reassembly...
-
Page 64: Camera
Steps 1. Place the display panel on a flat and clean surface . 2. Connect the display cable to the connector at the back of the display panel and close the latch to secure the cable . 3. Adhere the tape that secures the display cable to the back of the display panel . 4. -
Page 65: Installing The Camera
Steps 1. Disconnect the camera cable from the camera module. 2. Using a plastic scribe, gently pry the camera off the display back-cover and antenna assembly. Installing the camera Prerequisites If you are replacing a component, remove the existing component before performing the installation procedure. About this task Steps 1. -
Page 66: Display Back-Cover And Antenna Assembly
Display back-cover and antenna assembly Removing the display back-cover Prerequisites 1. Follow the procedure in before working inside your computer. 2. Remove the card. 3. Remove the base cover. 4. Disconnect the battery cable. 5. Remove the WLAN. 6. Remove the display assembly. -
Page 67: Power Button
Next steps 1. Install the camera. 2. Install the display panel. 3. Install the display bezel. 4. Install the display assembly. 5. Install the WLAN. 6. Connect the battery cable. 7. Install the base cover. 8. Install the card. 9. Follow the procedure in after working inside your computer. -
Page 68: Installing The Power Button
About this task Steps 1. Remove the two (M2x2) screws securing the power button to the palmrest. 2. Disconnect the power button cable and remove the power button from the system. Installing the power button Prerequisites If you are replacing a component, remove the existing component before performing the installation procedure. Disassembly and reassembly... -
Page 69: System Board
About this task Steps 1. Place the power-button board into the slot on the palmrest. 2. Install the two (M2x2) screws to secure the power button to the palmrest. 3. Connect the power button cable to the connector on the system board. Next steps 1. - Page 70 10. Remove the heatsink. NOTE: The system board can be removed along with the heat sink. 11. Remove the display assembly. Disassembly and reassembly...
- Page 71 About this task Disassembly and reassembly...
-
Page 72: Installing The System Board - Realtek Audio
Steps 1. Remove the two (M2.5x5) screws from the right hinge, Fold the right hinge up. 2. Disconnect the following cables from the system board: a. Speaker cable b. Keyboard FFC c. Power adapter port cable d. Keyboard backlight FFC e. - Page 73 Steps 1. Align and place the system board on the palmrest. 2. Replace the single (M2x4) screw that secures the system board to the palmrest. 3. Connect the following cables to the system board: a. Speaker cable b. Keyboard FFC c.
-
Page 74: Removing The System Board - Cirrus Logic Audio
Removing the system board - Cirrus Logic audio Prerequisites 1. Follow the procedure in before working inside your computer. 2. Remove the card. 3. Remove the base cover. 4. Remove the battery. 5. Remove the WLAN. 6. Remove the SSD. 7. -
Page 75: Installing The System Board - Cirrus Logic Audio
Steps 1. Disconnect the following cables from the system board: a. Speaker cable b. Keyboard FFC c. Power adapter port cable d. Keyboard backlight FFC e. Touchpad FFC f. Hard drive FFC g. IO board FFC h. Fingerprint reader FFC Power button FFC from the system board 2. - Page 76 About this task Disassembly and reassembly...
- Page 77 Steps 1. Align and place the system board on the palmrest. 2. Peel back the Mylar tape from over the screw hole. 3. Replace the two (M2x4) screws that secures the system board to the palmrest. 4. Connect the following cables to the system board: a.
-
Page 78: Power-Adapter Port
3. Install the system fan. 4. Install the memory 5. Install the SSD. 6. Install the WLAN. 7. Install the battery. 8. Install the base cover. 9. Install the card. 10. Follow the procedure in after working inside your computer. Power-adapter port Removing the power adapter port Prerequisites... -
Page 79: Installing The Power Adapter Port
Steps 1. Disconnect and un-route the power adapter port module from the system board. 2. Remove the power adapter port module from the system. Installing the power adapter port Prerequisites If you are replacing a component, remove the existing component before performing the installation procedure. About this task Steps Place the power adapter port module into the slot provided on the palmrest. -
Page 80: Palm-Rest And Keyboard Assembly
Palm-rest and keyboard assembly Removing the palmrest and keyboard assembly Prerequisites 1. Follow the procedure in before working inside your computer. 2. Remove the card. 3. Remove the base cover. 4. Remove the battery. 5. Remove the WLAN. 6. Remove the memory 7. - Page 81 Next steps 1. Install the system board. 2. Install the power adapter port. 3. Install the touchpad. 4. Install the board. 5. Install the heatsink. 6. Install the system fan. 7. Install the coin-cell battery. 8. Install the speakers. 9. Install the hard drive assembly.
-
Page 82: Chapter 6: Troubleshooting
● Using a non-Dell or incompatible battery may increase the risk of fire or explosion. Replace the battery only with a compatible battery purchased from Dell that is designed to work with your Dell computer. Do not use a battery from other computers with your computer. -
Page 83: Locate The Service Tag Or Express Service Code Of Your Dell Computer
Locate the Service Tag or Express Service Code of your Dell computer Your Dell computer is uniquely identified by a Service Tag or Express Service Code. To view relevant support resources for your Dell computer, we recommend entering the Service Tag or Express Service Code at www.dell.com/support. - Page 84 Table 4. LED codes (continued) Diagnostic light codes Problem description Recommended solutions Unrecoverable SPI Flash failure Replace the system board. Short in hinge cable tripped OCP1 Check if the display cable (EDP) is seated properly or pinched at the hinges. If problem persists, replace either display cable (EDP) or display assembly (LCD).
-
Page 85: Real-Time Clock (Rtc Reset)
Real-Time Clock (RTC Reset) The Real Time Clock (RTC) reset function allows you or the service technician to recover Dell Latitude systems from No POST/No Power/No Boot situations. The legacy jumper enabled RTC reset has been retired on these models. -
Page 86: Wifi Power Cycle
5. Press and hold the power button for 20 seconds to drain the flea power. 6. Install the battery. 7. Install the base cover. 8. Connect the power adapter to your computer. 9. Turn on your computer. NOTE: For more information about performing a hard reset, see the knowledge base article 000130881 www.dell.com/support. Troubleshooting... -
Page 87: Chapter 7: Getting Help And Contacting Dell
Getting help and contacting Dell Self-help resources You can get information and help on Dell products and services using these self-help resources: Table 5. Self-help resources Self-help resources Resource location Information about Dell products and services www.dell.com My Dell Tips...