Table of Contents
Advertisement
COPIER > OPTION > IMG-MCON
C-S-P-D
High dens end edge crrct: PDL dens prrty
Lv.2 Details
To set ON/OFF of high density trailing edge correction function at
PDL.
By selecting CAL (priority on density) in C-PDL-T, high density
trailing edge correction function is ON in normal operation; however,
set OFF as needed.
Use case
ON: When reducing jagged line and jagged outline of text
OFF: When matching density with original on high density area, or
when prioritizing density and gradation
Adj/set/operate method Enter the setting value, and then press OK key.
Display/adj/set range
0 to 1
0: OFF, 1: ON
Default value
1
Related service mode
COPIER> OPTION> IMG-MCON> C-PDL-T
Supplement/memo
Abbreviation of CAL_Shadow_PDL_Density
C-S-C-D
High density end edge crrct ON/OFF: copy
Lv.2 Details
To set ON/OFF of high density trailing edge correction function at
copy.
With CAL of COPY, high density trailing edge correction function is
ON in normal operation; however, set OFF as needed.
Use case
ON: When reducing jagged line and jagged outline of text
OFF: When matching density with original on high density area, or
when prioritizing density and gradation
Adj/set/operate method Enter the setting value, and then press OK key.
Display/adj/set range
0 to 1
0: OFF, 1: ON
Default value
1
Supplement/memo
Abbreviation of CAL_Shadow_COPY_Density. When adjusting the
input signal 255 to low in the case that the density of solid area is
too high, jaggy (jagged effect of halftone) may occur to text, etc. By
entering the input signal 255 as solid, occurrence of jaggy can be
prevented.
C-SM-P-G
[Not used]
Lv.1 Details
-
C-SM-C-G
[Not used]
Lv.1 Details
-
8
Service Mode > COPIER > OPTION > IMG-MCON
8
Service Mode > COPIER > OPTION > IMG-MCON
COPIER > OPTION > IMG-MCON
DH-TGT
Setting of D-half control target
Lv.1 Details
To set the target data of D-half control.
When the Reader is installed (copy model), D-half control uses the
gradation data before execution of PASCAL control and detection
result of D-half control after the execution as control target. If
controlled only by the patch image reading detection when Reader-
related failure occurs, set to the gradation data manually.
When the Reader is not installed (printer mode), only gradation data
is available.
Use case
When Reader-related failure occurs
Adj/set/operate method Enter the setting value, and then press OK key.
Display/adj/set range
0 to 1
0: Detection result of D-half control right after PASCAL control, 1:
Gradation data
Default value
0: Copy model, 1: Printer model
WDREDUCT
Setting of white dots reduction mode
Lv.1 Details
To set the white dots reduction mode.
When 1 is set, white dots become less significant by enlarging black
dots by thin line correction.
When white dots are significant
Use case
Adj/set/operate method Enter the setting value, and then press OK key.
Display/adj/set range
0 to 1
0: OFF, 1: ON
Default value
0
Related service mode
COPIER> OPTION> IMG-MCON> VDADDCNT, HDADDCNT, LIN-
OFST
Related user mode
Thin line correction, horizontal line correction, and vertical line
correction in user mode
VDADDCNT
Horz added dot amnt at white dots reduct
Lv.1 Details
To adjust the amount of dots added to side at white dots reduction
mode.
As the greater value is set, the size of white dot gets smaller.
When WDREDUCT is 1, this setting is enabled.
Use case
When adjusting the level of white dots reduction mode
Adj/set/operate method Enter the setting value, and then press OK key.
Display/adj/set range
0 to 4
Default value
1
Related service mode
COPIER> OPTION> IMG-MCON> WDREDUCT
8-150
8-150
Hide quick links:
Advertisement
Table of Contents
Troubleshooting
