Canon imageRUNNER ADVANCE DX C5870i Service Manual page 522
Hide thumbs
Also See for imageRUNNER ADVANCE DX C5870i:
- Faq manual (100 pages) ,
- Manual (96 pages) ,
- Faq manual (48 pages)
Table of Contents
Advertisement
E110-0003-05
Detection Description
Remedy
E110-0004-05
Detection Description
Remedy
E110-0005-05
Detection Description
Remedy
E120-1001-05
Detection Description
Remedy
E120-1003-05
Detection Description
Remedy
Startup BD phase lock error
The BD phase lock was not performed during the specified time at startup
[Related parts]
- Flat cable between the Main Controller PCB (UN41/J75) and the Laser Driver PCB (Y/M) (UN09/
J700)
- Laser Driver PCB (Y/M) (UN09) (Unit of replacement: Laser Scanner ASS'Y)
- Main Controller PCB (UN41)
[Remedy]
1. Check / replace the related harnesses / cables / connectors / parts.
2. After replacing the Laser Scanner Assembly, execute "Settings/Registration > Adjustment/
Maintenance > Adjust Image Quality > Auto Correct Color Mismatch".
Startup polygon surface detection error
The surface detection was not completed during the specified time at startup or the surface
detection was completed but the BD jitter exceeded +/- 0.5% of period
[Related parts]
- Flat cable between the Main Controller PCB (UN41/J75) and the Laser Driver PCB (Y/M) (UN09/
J700)
- Laser Driver PCB (Y/M) (UN09) (Unit of replacement: Laser Scanner ASS'Y)
- Main Controller PCB (UN41)
[Remedy]
1. Check / replace the related harnesses / cables / connectors / parts.
2. After replacing the Laser Scanner Assembly, execute "Settings/Registration > Adjustment/
Maintenance > Adjust Image Quality > Auto Correct Color Mismatch".
Startup polygon surface identification error
The surface cannot be specified at startup
[Related parts]
- Flat cable between the Main Controller PCB (UN41/J75) and the Laser Driver PCB (Y/M) (UN09/
J700)
- Laser Driver PCB (Y/M) (UN09) (Unit of replacement: Laser Scanner ASS'Y)
- Main Controller PCB (UN41)
[Remedy]
1. Check / replace the related harnesses / cables / connectors / parts.
2. After replacing the Laser Scanner Assembly, execute "Settings/Registration > Adjustment/
Maintenance > Adjust Image Quality > Auto Correct Color Mismatch".
Power supply error (24V)
24V was not input to the Laser Driver PCB when the power supply is turned ON
[Related parts]
- Harness between the Drum Driver PCB (UN54/J223) and the Laser Driver PCB (Y/M) (UN09/
J701)
- Laser Driver PCB (Y/M) (UN09) (Unit of replacement: Laser Scanner ASS'Y)
- Drum Driver PCB (UN54)
[Remedy] Perform the following in the while checking whether the error is cleared.
1. Check the connection of J200 on the Drum Driver PCB(UN54).
2. Check / replace the related harnesses / cables / connectors / parts.
3. After replacing the Laser Scanner Assembly, execute "Settings/Registration > Adjustment/
Maintenance > Adjust Image Quality > Auto Correct Color Mismatch".
Power supply error (3.3V)
3.3V was not generated by the Laser Driver PCB when the power supply is turned ON
[Related parts]
- Laser Driver PCB (Y/M) (UN09) (Unit of replacement: Laser Scanner Assembly)
[Remedy]
1. Check / replace the related harnesses / cables / connectors / parts.
2. After replacing the Laser Scanner Assembly, execute "Settings/Registration > Adjustment/
Maintenance > Adjust Image Quality > Auto Correct Color Mismatch".
510
8. Error/Jam/Alarm
- Quick Links:
- Table of Contents
- Paper Feed/Output Options
Hide quick links:
Advertisement
Table of Contents
Troubleshooting
