Configuring Snmp Using The Vxflex Os Gui - Dell EMC VxFlex Ready Node User Manual
Hide thumbs
Also See for EMC VxFlex Ready Node:
- Operating system installation manual (74 pages) ,
- Operating system installation manual (86 pages) ,
- Installation manual (92 pages)
Table of Contents
Advertisement
SNMP Trap Support
Alert Message in
Alert Message in
VxFlex OS GUI
REST
Network Adapter
NIC_PORT_DOWN
Link is down
Drive is ready to be
PHYSICAL_DRIVE_
removed
REMOVED_FROM_
OS
BOSS is not
STORAGE_CONTR
configured with
OLLER_INVALID_B
expected Raid Level
OSS_RAID_LEVEL
1
Interleave must be
NVDIMM_INTERLE
enabled in BIOS
AVE_DISABLED
when NVDIMM
devices are present
Persistent Memory
NVDIMM_PERSIST
must be enabled in
ENT_MEMORY_DIS
BIOS when
ABLED
NVDIMM devices
are present
NVDIMM battery
NVDIMM_BATTERY
state is low.
_INVALID_STATE
Install or check GPU
GPUCARD_MONIT
drivers
ORING_ERROR
Replace DIMM
DIMM_IN_ERROR_
STATE
DIMM reports
DIMM_IN_DEGRAD
Degraded state
ED_STATE
Configuring SNMP using the VxFlex OS GUI
Dell EMC VxFlex Ready Node AMS User Guide
320
Table 35 VxFlex Ready Node–specific Alerts in SNMP, VxFlex OS GUI, REST, and
ESRS (continued)
Alert Message in
SNMP Trap
Nic.Nic_Port.Nic_P
ort_Down
Node.Physical_Driv
e.Ready_For_Remo
val
Node.Boot_Drive.In
valid_Boss_Raid_Le
vel
Node.Ram.Invalid_In
terleave_Bios_settin
g
Node.Ram.Invalid_P
ersistent_Memory_
Bios_setting
Node.Ram.NVDIMM
_Battery.Invalid_Sta
te
Node.Gpu.Monitorin
g_Error
Node.Ram.Error_St
ate
Node.Ram.Degrade
d_State
Configure SNMP and add trap receivers using the VxFlex OS GUI.
Before you begin
Ensure that you can authenticate to the VxFlex OS GUI with an admin user.
l
Alert Code
Severity
(for ESRS)
SIO11.01.0000
5 (Critical) The network link is down in
001
SIO07.06.000
2(Warning
0001
)
SIO07.01.000
5 (Critical) Check the BOSS setup
0002
SIO07.04.000
5 (Critical) Enable NVDIMM interleave in
0004
SIO07.04.000
5 (Critical) Enable Persistent Memory in
0005
SIO07.04.000
5 (Critical)
0006
3 (Error)
SIO07.06.000
2(Warning
0001
)
SIO07.04.000
3 (Error)
0007
SIO07.04.000
2(Warning
0008
)
Recommended Action
the network adapter. Verify
that the network adapter is
enabled in the operating
system, and verify that the
network cable is connected
properly at both ends.
The drive is ready to be
removed from the node.
configuration
BIOS settings.
BIOS settings
Check the NVDIMM battery
status. A fault in the battery
will impact the NVDIMM
persistent memory.
Persistent memory will not
function if battery is faulty.
Check that the GPU drivers
are properly installed on the
node.
Replace DIMM
Replace DIMM as soon as
possible
- Quick Links:
- Introduction to Vxflex Ready Node
- Hardware
Hide quick links:
Advertisement
Chapters
Table of Contents
